Related
Was trying to install wp7 on my hd2, but now im stucked on magldr version 1.13. Forgot that the volume buttons doesnt work and i cant get the phone out of there. Try to load original rom or even task 29 but nothing becuase the pc doesnt recognize it. When the phone its booting it says something like cant boot from sd android kernel fail and then the menu and i can select only the first 1 boot wph.
Is there a way to get the phone out of there, or my only hope its to repair the volume button.
thanks
If you haven't been able to flash anything then as long as you just reboot your phone you'll just go back to whatever ROM you had previously
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
i remove the battery but when the hd2 start again it boots instantly to magldr, i need another way to flash it different to the three color screen (i cant get there becuase the volume down button its broke).
i have a problem like that
If your volume keys don't work, then there is seriously, no other way. You can't get into bootloader mode without the volume keys, and the you can't flash a different rom without the volume keys, so yeah, your device is pretty much bricked....
But IF the vol. down key works, I assume that it is something with MAGLDR or HSPL, or possibly an error in RAM. Are there anything that can be flashed via magldr that checks the state of underlying HSPL?
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Maybe I'm tired or too old... but I don't understand your questions
You can imagine the different "softs" as layers:
1st: HSPL (or SPL) - it's the one you enter by pressing vol-down while booting.
this one give you the ability to flah a WM ROM (original or custom), a radio or MAGLDR
So if vol-down if dead... your phone also
nb: the first splash screen is at this level, so it will be still here after flash of MAGDR, CWM, NAND, WM7...
2nd: MAGLDR - it's the one you go in by pressing "end call" while booting.
It gives the ability to flash a NAND or WM7 via DFT
So if "end call" is dead... you're not But it's anoying I think...
3rd: CWM - it's the one you go in by selecting "AD recovery" in MAGLDR
It gives you the ability to flash a "CWM NAND" or an update... It also gives the ability to backup/restore a NAND.
So please clarify your question if you need help. More important do not post different problem by saying "same here". It's just confusing. Even if you can't boot your NAND it's not always the same problem
Let's try again dudes
osugsxr said:
any fix to this??? same issue following the steps and volume buttons dont work. I can select the boot wph ....wph not installed
Click to expand...
Click to collapse
HTC after sales... or few bucks
That is what I'm thinking, will try warranty to see if that works if not not ill see what they charge. For now back to the nexus s.
truc007 said:
HTC after sales... or few bucks
Click to expand...
Click to collapse
Sent from my Nexus S using XDA App
This is the answer to your problem if it does work find someone that is not a noob and have them fix your phone its really not that hard
Ok guys please help me I don't wanna start new thread
I installed on my hd2:
-HSPL 2.08
-Radio 2.15.50.14
-Magldr 1.13
-CMR
First of all I noticed that I dont have to hold the power button to get into the magldr menu.
I couldn't get into Boot As SD so I wanted to flash custom rom from bootloader. Unfortunately I can't do that. Even tried HR. Is there any solution to flash stock ROM
Any help would be greatly appreciated
Stuck for me too
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
hi, have u tryed with the small button under the volume down button? it works as the volume down button...
If u can go in bootloader (if ur volume down works) could be ur nand is corrupted (as mine ) so bye bye hd2... i m waiting for the htc sensation
DAF doesnt' work
ChitownWingMan said:
I just flashed the latest hspl3, radio code and MAGLDR 1.13.
When I try to boot MCCM 4.5 from SD it hangs on the main Android Home Screen. When I try to boot WPH MAGLDR says that WPH is not installed.
I am still running Windows Mobile 6.5.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I figured out the Android problem (I needed a different rootfs).
I have magldr 1.13 working!!!!
However, when I try to run DAF I get the same:
"An error has occurred
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (725)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (304)"
error that I have seen all over XDA-Dev.
However, none of the fixes I have seen on here have worked. I am running Windows 7 Professional.
I have tried:
Disabling Use USB in the Window Mobile Device Center
I have tried ANDR_INSTALL
I have rebooted
I have tried deleting all of the unattached USB device in the device manager.
I have tried using LeoAdvancedRUU
I have tried starting DAF first and then connecting the usb cable
I have tried connecting the USB cable first and then the starting DAF.
Help please!!! I was up until 8:30 AM trying to get this to work (I started at about 10:00 PM).
i also put the hd2 into the freezer for 10 minutes to solve heat problem and it doesn't start bootloaderi...
the nand corrupted..it start magdle but don't start android or cwm..there is nothing to do
tser04 said:
I have the same problem, after having upgraded to 1.13. Whenever i try to install a NAND version of Android, i am stuck with the splashscreen of the build i am trying to boot into. Bear in mind that every ROM i flash is flashed without any problems. So I guess it is not the NAND memory thats broken or faulty. The only build i am capable of running, is DFT's WP7 stock build. This loads perfectly, but due to the battery drain i would VERY much like to get rid of it and use my beloved MDJs Gingerbread/CM7 2.6 build.
To avoid any trouble i thought of just flashing a Task29, and a stock WM65 ROM to 'reset' to stock, that is, installing a custom ROM from SD card, so SPL is restored to factory version. However, i am not able to enter bootloader mode on my HD2. It can only boot into Magldr and succ. WP7. It doesn't help to press vol down, and it is not broken as I can use it in WP7. It seems as though HSPL is skipped and the phone is boot directly into magldr. This should NOT happen.
Anyways, this is very much close to a bricked device for me, so i am very sad these days. Does ANYONE know a trick that would enable me to replace magldr 1.13 with the working 1.12 without the tri-colour bootscreen of spl?
Click to expand...
Click to collapse
I have the same exact problem !! WP7 is the only OS that works and I want android
also the volume down key works...should I try to reflash HSPL ?? will that work ?? since HSPL 2.08 is already installed !??
Happen error
Read below for more information
Error Description: Config load failed.
Info: .\RSPL\RSPL.cpp (712)
Error Description: CONFIG: can't open config file
Info: .\RSPL\RSPL.cpp (291)
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
more data needed.
it looks like you're saying it loads HSPL 2.08 then loads magldr then when it tries to load the ROM it gives the fatal thing right?
so what happens after you flash a winmo ROM? does it hang? where? what exactly happens when you turn on your phone? have you tried flashing stock WM6.5?
Yup the fatal error appear on magldr v.1.13
Ive tried task29..
Then when i tried install windows stock 6.5 it stuck on the white htc screen without any red letters on the bottom like usual..
It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems
flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
I had the same problem. I tried every imaginable solution and nothing would work. I flashed WinMo from the bootloader screen, and SD card and it would sometimes load, but would freeze or hang up most of the time during boot. I tried flashing a DFT ROM, and it would boot about 20% of the time, and hang the rest. When it would boot, it would freeze once it got warm.
Luckily my phone was still under warranty.
fra1977 said:
It looks is a risk to do flashes, I have HTC HD2 and I'd lile to installa Android on Nand, but I'm scared by the possibles problems
Click to expand...
Click to collapse
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.
....................
I have the same problem. After trying everything, now it sometimes boots into windows but after a while it suddenly stops working and reboots and sucks on white htc screen....
Tomorrow it will go back for warranty...
does anyone knows how this fatal hit error happens? I used the phone without problems for over 2 weeks with android on nand, before the problems started.
Sent from my HTC HD2 using Tapatalk
I think that this is the problem that made us wait too long for MAGLDR.. cotulla thought that he fixed it but looks like he didin't... i think the bootloader has overwroten the SPL..
Can you guys give more details about your HD2s like "When have you bought it" "which screen you have" ?
flawlessx92 said:
I've tried search engine,ive tried everything but my phone still wont boot up:
Im currently using HSPL2.08 and my phone was just fine installing Imilka's Desire HD Ram NAND version yesterday...Installed the rom via clockworkmod and it was just fine..but then yesterday my phone freeze so i pull out the battery..then when i started to boot up the phone again...at Magldr v1.13 the phone shows FatalHit error while loading ROM..Im using radio v2.15 btw
Stuff that I've tried to fix:
Tried Task29,Reflashed WinMo 6.5 stock rom v1.66,tried reinstall magldr v1.13 even tried v1.11 and tried using other radio,using 2 different sim cards and SD cards,tried flashing via USB(TriColour Boot) and SD...EVERYTHING!!
T~T I really dont know what to do...Please help...at this phone i just want my HD2 to be able to boot up again no matter what OS..just want my phone back..
Click to expand...
Click to collapse
It seems to me like many bad blocks on NAND...
How to verify that:
1) flash cLK (chose a partitioning your prefer)
2) via cmd run the following commands
Code:
fastboot erase boot
fastboot erase recovery
fastboot erase system
fastboot erase cache
fastboot erase userdata
If you have bad blocks it will show up in console of cLK
It will look like this
[6521] can't erase block @ 3424
[6521] bad block @ 3424 (or something like that)
You need to have adb drivers installed and fastboot.exe for the commands. If you don't have download them from here
Put the in a folder i.e. c:\android
navigate with cmd there and run the commands.
CWM can recognize bad blocks and skip them, therefore if you have many in each partition you can create larger partitions for /boot and /system and your phone will work properly until you decide to send it for repair.
If i remember well each block is 128KB
MAGLDR v1.13 on my HTC HD2
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Same problem here, it seems the problem is with HD2 1024mem.. Tmous?? will CLK installation will solve? anyone with more suggestion? I would really really appreciate..my hd2 is laying on table for 2 weeks now with no solution
Ive noticed the fatal hit error on the hd2s with those tiny dots in the screen.
sent from my Nexus S
teutakarakashi said:
i have installed MAGLDR v1.13 on my HTC HD2
Phone have rebooted after installation finished, but DFT MAGLDR Bootloader have not loaded after these(
now i see only a white screan with the green text: ''HTC'' on it
please can somebody help me?
Ps : i had the correct radio ROM
HSPL 3.03
Radio 2.15
Click to expand...
Click to collapse
Your problem is wrong hspl.Magldr works only with hspl 2.08
sent from my hd2 using ics
WorldWide60 said:
The statistics are in your favor. If you were to compare all of the times that our HD2's have been flashed versus the amount that have been bricked, it would probably be less than 1% that have been bricked. IMO, Android is so much better than WinMo that it's well worth the risk.
Click to expand...
Click to collapse
agree with that
Did a hd2 the other day. Fatal hit error popped up. Done hundreds of hd2s. Bricked 2. On the particular hd2 i booted into magldr and did a reset. Had to reboot bout 20x to finally work. When it finally booted the touch was unresponsive. After another 10 or so reboots it finally stuck. Easy phone to mod but highest brick rating for me. I flash phones for a living so i know what im doing. Ive bricked my own g1 learning back in 09 and bricked 2 hd2s in 2011. There must be certain hd2s that dont accept the flash. Ive noticed the hd2s with the dots in the screen have been the only ones that give a hard time. Are theres the euro version? I only flash android on them not keep up with its development.
sent from my Sensation
I have a Vodafone HD2, and tried to run NAND Android on it many times, to no avail. I installed Hyperdroid GBX on MAGLDR, and made sure to follow the instructions carefully. It worked fine, and after a few days, when I tried powering on, it got stuck on the white Android logo. I took out the battery, booted into MAGLDR, recovered to a backup, but it still wouldn't boot, it was just stuck at the Android logo. So I did Task 27, flashed radio (Radio Leo 2.15.50.14), HSPL (2.08.HSPL), installed magldr 1.13, cwm 150MB partition, and the same rom (Hyperdroid GBX Magldr), and the same thing happened. It worked fine for a couple of days, then wouldn't boot. I tried the same process, with different roms. (Typhoon CM7, and Hyperdroid CM7) and the same thing keeps happening. I even tried installing CLK, but with CLK, I didn't even get the rom to boot the first time, it just sat there at the white Android logo.
This is getting to be very frustrating.
Please help me, if you can.
zyxw121 said:
I have a Vodafone HD2, and tried to run NAND Android on it many times, to no avail. I installed Hyperdroid GBX on MAGLDR, and made sure to follow the instructions carefully. It worked fine, and after a few days, when I tried powering on, it got stuck on the white Android logo. I took out the battery, booted into MAGLDR, recovered to a backup, but it still wouldn't boot, it was just stuck at the Android logo. So I did Task 27, flashed radio (Radio Leo 2.15.50.14), HSPL (2.08.HSPL), installed magldr 1.13, cwm 150MB partition, and the same rom (Hyperdroid GBX Magldr), and the same thing happened. It worked fine for a couple of days, then wouldn't boot. I tried the same process, with different roms. (Typhoon CM7, and Hyperdroid CM7) and the same thing keeps happening. I even tried installing CLK, but with CLK, I didn't even get the rom to boot the first time, it just sat there at the white Android logo.
This is getting to be very frustrating.
Please help me, if you can.
Click to expand...
Click to collapse
Hi,
Which version of MAGLDR are you using?
I'm using MAGLDR 1.13.
zyxw121 said:
I'm using MAGLDR 1.13.
Click to expand...
Click to collapse
Hi,
Sorry,which version of CWM?
I've been using 3.0.2.5, but I'll try with 3.0.2.4. I'll get back to you on it in a couple of days.
Thanks!
EDIT: The link you gave me downloads a 120MB partition size, but Typhoon CM7 requires a 150MB partition. Is it still going to work?
zyxw121 said:
I've been using 3.0.2.5, but I'll try with 3.0.2.4. I'll get back to you on it in a couple of days.
Thanks!
EDIT: The link you gave me downloads a 120MB partition size, but Typhoon CM7 requires a 150MB partition. Is it still going to work?
Click to expand...
Click to collapse
Hi,
Try KSUBEDI's TOOLKIT (Don't forget to thank him)
There is the ability to downgrade CWM
UPDATE
My phone froze, and then rebooted, however, it gut stuck at the white android logo. I waited for a few minutes, then took the battery out. I ran task 29, then LEOIMG. After that, I installed HSPL 2.08.HSPL, and tried to install MAGLDR 1.13. However, it was unsuccesful. It seemed to have flashed fine, with the progress bar going to 100, then rebooting, but after that, it got stuck at the white HTC screen. I tried taking out the battery, and holding down the power button while booting, but nothing works. I haven't yet got around to flashing CWM.
Do you think that perhaps cLK would work better?
Any help would be appreciated.
zyxw121 said:
UPDATE
My phone froze, and then rebooted, however, it gut stuck at the white android logo. I waited for a few minutes, then took the battery out. I ran task 29, then LEOIMG. After that, I installed HSPL 2.08.HSPL, and tried to install MAGLDR 1.13. However, it was unsuccesful. It seemed to have flashed fine, with the progress bar going to 100, then rebooting, but after that, it got stuck at the white HTC screen. I tried taking out the battery, and holding down the power button while booting, but nothing works. I haven't yet got around to flashing CWM.
Do you think that perhaps cLK would work better?
Any help would be appreciated.
Click to expand...
Click to collapse
Try to:
Install MAGLDR 1.13
Download CWR 4.0 and flash it in MAGLDR: http://www.multiupload.com/VZ1WB57AOY
Download this rom: http://www.multiupload.com/8UPNV5WUZU and install it in CWR.
Thanks, but I CAN'T install MAGLDR.
I flash it, and then my phone reboots and gets stuck at the white HTC screen.
ANOTHER UPDATE
I ran LEOIMG again, and this time tried to install cLK. It flashed fine, rebooted, and then got stuck at the white HTC screen, just as with MAGLDR.
I really am lost here. Does anyone have any ideas?
Thanks.
zyxw121 said:
ANOTHER UPDATE
I ran LEOIMG again, and this time tried to install cLK. It flashed fine, rebooted, and then got stuck at the white HTC screen, just as with MAGLDR.
I really am lost here. Does anyone have any ideas?
Thanks.
Click to expand...
Click to collapse
I would say do a task 29 and install wm6.5 first. then start the process from scratch.
Install this ROM this time.
http://forum.xda-developers.com/showthread.php?t=915159
This is a closest rom as wm 6. Let me know how it went if everything is fine then you can rule out that your phone is fine. also make sure
your anti-virus is turned off. Taking this simple steps will help you a lot in the future.
Good luck
PROBLEM SOLVED
It seems the problem is, I was forgetting to flash the radio . So I did that, and MAGLDR installed perfectly, as did CWM. I'm just installing the ROM (Hyperdroid GBX) now, but everything seems to be fine.
Thanks for all your help guys!
Glad you figure it out. Please press thanks
Sent from my Nexus One using XDA App
Hello, i have installed a SD version of android on my HTC HD2 it started normally but after i rebooted i got stuck on the winmo Bott screen(Htc in green with white background)
Ps : i have acess to the HSPL boot loader but i haven't tried anything(afraid that i brick my phone )
I am a complete noob and any help will be appreciated.
midoBB said:
Hello, i have installed a SD version of android on my HTC HD2 it started normally but after i rebooted i got stuck on the winmo Bott screen(Htc in green with white background)
Ps : i have acess to the HSPL boot loader but i haven't tried anything(afraid that i brick my phone )
I am a complete noob and any help will be appreciated.
Click to expand...
Click to collapse
did you use magldr or cLK?
I would go back to the tri-color screen flash task29, then reflash magldr or cLK or whatever you're using.
i suspect he means a haret version of android.
I had exactly the same thing every time i tried haret android over winmo, time and time again, for months, until nand android came along. They wouldnt boot, and resetting hung at boot screen forcing a hard reset. On the very few occasions an android build booted, they would work until i soft reset, then it gave the same hang at boot screen forcing hard reset symptoms. Mostly tho they just didn't boot, and the same hung at boot screen forcing hard reset.
I'll never try sd android again! never did find out why.
samsamuel said:
i suspect he means a haret version of android.
I had exactly the same thing every time i tried haret android over winmo, time and time again, for months, until nand android came along. They wouldnt boot, and resetting hung at boot screen forcing a hard reset. On the very few occasions an android build booted, they would work until i soft reset, then it gave the same hang at boot screen forcing hard reset symptoms. Mostly tho they just didn't boot, and the same hung at boot screen forcing hard reset.
I'll never try sd android again! never did find out why.
Click to expand...
Click to collapse
Sounds like an old radio or the fact that you didn't use a card reader to transfer the files, maybe they were corrupting in the transfer, I had this come up a few times.
I am using a haret version and the phone is not stuck at the android boot screen but at the winmo boot screen and i didn't use any magldr or clk
i have hspl installed and i have stock winmo
Hello,
I had this issue first time I changed from WinMo to Android. Stuck on the HTC boot screen. It was because there was no OS installed on it.
And I solved it by updating the Radio before updating the ROM.
So I would recommend you to first update your Radio, then try again installing your Android ROM.
midoBB said:
I am using a haret version and the phone is not stuck at the android boot screen but at the winmo boot screen and i didn't use any magldr or clk
i have hspl installed and i have stock winmo
Click to expand...
Click to collapse
mariegalante55 said:
Hello,
I had this issue first time I changed from WinMo to Android. Stuck on the HTC boot screen. It was because there was no OS installed on it.
And I solved it by updating the Radio before updating the ROM.
So I would recommend you to first update your Radio, then try again installing your Android ROM.
Click to expand...
Click to collapse
That's good advice, try the 2.15.50 radio, also make sure you are transferring via sd card reader to avoid data corruption. Also try a different ROM.
Stuck with NAND magdlr
Hello,
I tried to install several ROMs through ClockworkMod Recovery.
Everything went fine, with all of them, except when i rebooted before the first use. With all the roms my HD2 stayed on the bootscreen..
Please help me out!
midoBB said:
Hello, i have installed a SD version of android on my HTC HD2 it started normally but after i rebooted i got stuck on the winmo Bott screen(Htc in green with white background)
Ps : i have acess to the HSPL boot loader but i haven't tried anything(afraid that i brick my phone )
I am a complete noob and any help will be appreciated.
Click to expand...
Click to collapse
is your problem solved..i am facing the same
---------- Post added at 08:44 AM ---------- Previous post was at 08:37 AM ----------
orangekid said:
did you use magldr or cLK?
I would go back to the tri-color screen flash task29, then reflash magldr or cLK or whatever you're using.
Click to expand...
Click to collapse
hey can i directly install magldr after task 29 without installing os..PLEASE help facing the same .tried everything
Yes, phone into bootloader, connect USB, flash
HI everyone,
This is the first time for me posting a thread here...thanks in advance.
Well I have a HTC HD2 that is a friends of mines. He was trying to change the radio so it could work in another country and managed to brick the phone. He got tired of trying to fix the phone so he gave it to me. I have tried fixing it with a tool kit I downloaded in another thread here. I managed to get it to boot butt it wouldn't get past T-Mobile screen...I kept on messing with it trying to install a ROM and different radios but non will work and wont turn on anymore but still is able to be recognize but PC(not mobile media center) and the last thing I did was task29. It stopped at 99%...still can load bootloader 3 colors but having a harder time getting the phone recognize by PC. Can anyone help me before I get into a deeper hole? If your need any more detail please ask me...btw the phone is running SPL- 3.03 HSPL in boot loader.
to the rescue !!
Jaimelebrone said:
HI everyone,
This is the first time for me posting a thread here...thanks in advance.
Well I have a HTC HD2 that is a friends of mines. He was trying to change the radio so it could work in another country and managed to brick the phone. He got tired of trying to fix the phone so he gave it to me. I have tried fixing it with a tool kit I downloaded in another thread here. I managed to get it to boot butt it wouldn't get past T-Mobile screen...I kept on messing with it trying to install a ROM and different radios but non will work and wont turn on anymore but still is able to be recognize but PC(not mobile media center) and the last thing I did was tasIt29. It stopped at 99%...still can load bootloader 3 colors but having a harder time getting the phone recognize by PC. Can anyone help me before I get into a deeper hole? If your need any more detail please ask me...btw the phone is running SPL- 3.03 HSPL in boot loader.
Click to expand...
Click to collapse
your friend shouldnt have flashed the radio without proper info !!
radio is the only thing which bricks the device !!!
dont worry we'll try to sort something out !!
firstly start with flashing a proper radio !!
http://forum.xda-developers.com/showthread.php?t=611787
download the radio 2.15.50.14 from this thread and flash it !!
NOTE : if you cant flash radio from ur pc, via nbh installer or the toolkit, you can flash it from a memory card !!
just format a normal memory card, put the radio on the card, rename the radio file to LEOIMG.nbh and get to the bootloader screen !!
follow the instructions from there and flash the radio !!
secondly if you want android or wp7-7.5 on ur device !! hspl 3.03 wont work !!
so install hspl 2.08 for that !!
for winmo6.5 3.03 is ok !!
do a task 29 once and flash any rom or magldr(for android or wp7-7.5)!!
good luck .....
thanks for quick reply
I am trying to do what you instructed me.
Didn't work
I tried it on the PC and it sadly stopped @ 96%, now it wont turn on volume down+power. Battery was charged and i didn't turn off. It displayed error 262. as soon as I can I will try it on sd card. Thanks though.
I was not able to install the radio but did in fact get to task29 successfully and MAGLDR Version-1.13. Now my phone is stuck in the Stick together screen. Can anyone help me from here what should I do. thanks I will be waiting for a responce.
Do you still need help cos its really easy to unbrick your phone and I say this because once I flashed 5 different roms in 2 hours or less and my phone wouldn't even turn on and when it did it would get stuck on the tmObile splash screen and restart but I fixed it and now I'm running the best Rom out there lol... reply to this thread and I'll tell you what to do
Sent from my HTC HD2 using xda premium
The thing is that I can't get any ROM's to finish installing...in the SD card the power button does not work...and in the computer the fartest I gotten was 99% but always stops and gives me error ussualy Error 262. Ireally don't know what to do. MY friend said he took it to an Asian Guy...I noticed that the battery S/N does not match the phone...can this have an effect...I haven't been able to flash any ROMS successfully not even the debranded stock. I flashed several phones and installed many different custom firmwares but this phone has been a real challenge...I'm over 2 weeks in...Thanks for the help thus far you guys are the best...
leoimg.nbh won't start to install
Hi everyone,
I have a severe problem with my HTC HD2 after installing a NAND version of android which did not work very well, than wanting to reinstall winmob 6.5 (vodafone) it startet "loading" the leoimg.nbh from the SD-card, but than stayed in this status neverending. So I interrupted (was that the mistake?? :-( }. Now I'm able to start MAGLDR 1.13, am also able to install another NAND version, but with every version I get the message: problem with android.xxx and so on.
I can start the bootloader modus (SPL-2.08.HSPL 8G XE), also connect by USB, but if I try to reload any leoimg.nbh from SD card - it does nothing, just stays in the bootloader modus.
Did I destroy any hardware by interrupting the non functioning "loading"?
Please help, if you can, what I could do now to get a functioning NAND android again!
Many thanks in advance!!!
freak just try the task 29 and u might return everything to normal condition
and for future never interrupt the installation process as u can brick ur device
for the main topic, i can say that ur device is fully bricked and the only way is taking it to the service center or try flashing directly into the hardware, but thats dangerous and requires professional skills
Plz help!
bigtobitobs said:
Do you still need help cos its really easy to unbrick your phone and I say this because once I flashed 5 different roms in 2 hours or less and my phone wouldn't even turn on and when it did it would get stuck on the tmObile splash screen and restart but I fixed it and now I'm running the best Rom out there lol... reply to this thread and I'll tell you what to do
Sent from my HTC HD2 using xda premium
Click to expand...
Click to collapse
Please can you help me.. I did the same thing.. it kept getting stuck at 0% and then i had to wait like an hour and then i tried again.. now its completely dead!
Please tell me what to do..
Thanks
First of all; This steps can solve your problem. But first of all(don't forget to check 2.08.HSL) try to use "Task29" and if it is success, load Radio ROM 2.15.50.14, and load original Winmo 6.5 ROM (Tmous or EU which phone do you use).
If you are stuck somewhere, then;
Download an original ROM for your HTC device from HTC webside.
- Format your SD card like FAT32 primary.
- Take "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
Radio ROM 2.15.50.14;
Radio ROM 2.15.50.14
HD2 Toolkit 4.2.0.1; ( contains task 29, magldr and recovery and also HSPL)
HD2 Toolkit 4.2.0.1
it's revived!
powerofthink said:
First of all; This steps can solve your problem. But first of all(don't forget to check 2.08.HSL) try to use "Task29" and if it is success, load Radio ROM 2.15.50.14, and load original Winmo 6.5 ROM (Tmous or EU which phone do you use).
If you are stuck somewhere, then;
Download an original ROM for your HTC device from HTC webside.
- Format your SD card like FAT32 primary.
- Take "RUU_signed.nbh" from an original ROM and copy it to your SD card.
- Rename to "leoimg.nbh"
- Reset your device while pressing the volume down button.
After several attempts to switch on the phone it finally turned on so I immediately installed stock ROM and it didn't get stuck on 0%.. it worked!!
Do you think I should perform a task 29 now or I can just proceed with installing a new radio and then installing a new ROM?
Thanks again mate!
Apparently I need to install SPL 2.08 before trying to install HSPL and then run android.. anyone know where I can find it?
Nevermind figured everything out Thanks anyway
Click to expand...
Click to collapse
If you want to change your ROM with one another like Android NAND ROM or Windows 6.5 ROM, then use this procedures.
For NAND Android ROM; You must flollow this sequence;
first check your device if it is 2.08.HSPL, and format your sdcard ext3 or ext4 and 1gb (which one you must use is pointed out by your Android chief). Copy new Android ROM into your sdcard's FAT32 section. insert it into your HTC device.
1. do task29
2. instal radio rom 2.15.50.14
3. install magldr 1.13
4. do recovery 5.0.2.6
5. do clear cache and dalvik cache.
6. Choose your android ROM .zip file on sdcard, load and enjoy...
For Windows 6.5 Follow this sequence;
first check your device if it is 2.08.HSPL, Format your sdcard like FAT 32 primary partition. insert it into your HTC device.
1. do Task29
2. Install Radio ROM 2.15.50.14
3. Run LeoCustomRUU.exe like "Run as Administrator" which Windows 6.5 rom you chose to use.
Radio ROM 2.15.50.14;
Radio ROM 2.15.50.14
HD2 Toolkit 4.2.0.1; ( contains task 29, magldr and recovery and also HSPL)
HD2 Toolkit 4.2.0.1
ActiveSync
Hi..
I am new here...
I would like to ask about my htc hd2..
I ve installed android 2.3 and yesterday i tried to update to android 4.0 but something went wrong and now my phone can't load anything...
when i tried to install ROM, it shows phone is not connected...
My ActiveSync also doesn't detect my phone... I can't enter to phone settings coz the phone won't load...
Any ideas ?
Thanks...
Zerocool_uia said:
Hi..
I am new here...
I would like to ask about my htc hd2..
I ve installed android 2.3 and yesterday i tried to update to android 4.0 but something went wrong and now my phone can't load anything...
when i tried to install ROM, it shows phone is not connected...
My ActiveSync also doesn't detect my phone... I can't enter to phone settings coz the phone won't load...
Any ideas ?
Thanks...
Click to expand...
Click to collapse
Are you booting into bootloader and connecting the device to your computer so you can get the HTC Sync connection. Just boot into bootloader by holding the volume down button down and poewering on your device. Connect it to your computer via USB and when you see Serial in the white bar of boo5tloader change to USB you have the HTC Sync connection and can flash your device.
I face a very odd problem with my HD2 EU. After years of 2 different versions of Android on nand I decided to reset it to stock(Vol down+power with leoimg.nbh in root of a FAT32 formatted microsd). When I get in bootloader mode there seem to be 2 instances of bootloader. The first 3 colour screen with all the right wordings lasts a second or two then I get a second 3 colour screen with the same wordings. With my Verbatim 8Gb class4 microsd formatted FAT32 and leoimg.nbh (obtained from the original RUU_Leo_HTC_ITA_1.66.408.1_Radio_15.32.50.07U_2.07.51.22_2_Signed_LEO_Ship.exe) in the root directory, the device does not recognize the file and it's not possible to restore the phone to stock, but I can only get into usb connection.
Being able to get in usb mode with the various versions of HSPL (1-2-3-4) I can still change the bootloader. With the HD2 Android toolkit 4.2.0.1 I can install cLK, Magldr, do a Task29 and repartition.
When I use the RUU installer I can install the RUU_signed.nbh that I used to get the leoimg.nbh BUT when I do it, and it does finish gracefully, on the screen that states the currently installed image THE INDICATION OF SUCH AN IMAGE IS BLANK whilst the name of the image to install is the one I am flashing.If I reflash the same image AGAIN (so I know what's on the device) the info of the installed image is never displayed.So after trying the various bootloaders HSPL and SPL and getting the same result you are my only resort.
Has anybody experienced such a problem? It is as if the the bootloader goes through a script that then starts a second "identical" bootloader (I understand that I may seem crazy) that is not capable of recognizing a leoimg.nbh. All my buttons are still working so it's definitely not a button problem. Therefore in a nutshell the question is: if I can't get the device to recognize a leoimg.nbh is there any other way to make it do so, given that I can communicate via usb without problems ?