MAGLDR 1.11 to MAGLDR 1.13 - HD2 Android Q&A, Help & Troubleshooting and Genera

Please tell me how to upgrade from
MAGLDR 1.11 to MAGLDR 1.13.
Thanks
Sent from my HTC HD2 using XDA App
Sent from my HTC HD2 using XDA App

Is it hard? No.
Download 1.13
Put your phone bootloader (tricolor screen)
Connect to pc
Run romupdate exe
Read onscreen guides, make choice
Done
Enjoy your new MAGLDR
Sent from my HTC HD2 using Tapatalk

Im doing that but on romupdate shows me error because my phone is not sync with mobile device centar, but that is imposimble because phone is flashed with android
Sent from my HTC HD2 using XDA App

boki_thegame said:
Im doing that but on romupdate shows me error because my phone is not sync with mobile device centar, but that is imposimble because phone is flashed with android
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
me too have the same problem

I solved that. First you need to install HTC Sync for all HTC Android Phones (i cant post hyperlinks if you want i will send you link via DM ) and after you will can to upgrade MAGLDR

You don't need to install anything, just turn off phone, then turn back on holding down volume down button until you see tri-colour bootloader.
At the bottom you will see the word serial then plug into PC, thenafter a few seconds you'll see it change to usb, then flash 1.13.
Hope this helps
Sent from my HTC HD2 using XDA App

You don't need ActiveSync.
The ROM Update Utility .exe will recognize and skip to step starting with the tricolored screen (hold vol down and power on). Ie. it will recognize your phone from there on.
You can do this to update anything from NAND Rom, Radio, MAGLDR etc. once you are no longer tied to Windows Mobile (activesync). The ROM updater skips those steps.
Did it just now.

does it erase the setup you have on your phone? or can you just upgrade with no issues?

I'm interested, too, if there's any data loss.
I read somewhere something that after upgrade the android needs to be flashed again.

builtboosted said:
does it erase the setup you have on your phone? or can you just upgrade with no issues?
Click to expand...
Click to collapse
Shivan149 said:
I'm interested, too, if there's any data loss.
I read somewhere something that after upgrade the android needs to be flashed again.
Click to expand...
Click to collapse
No, flashing from 1.11 to 1.13 does not result in data loss (normally - to be safe I'd suggest taking a backup though)

ClydeB1 said:
No, flashing from 1.11 to 1.13 does not result in data loss (normally - to be safe I'd suggest taking a backup though)
Click to expand...
Click to collapse
Thanks! So I can update without much work after the update.

Shivan149 said:
Thanks! So I can update without much work after the update.
Click to expand...
Click to collapse
So I did it and no problems!

does updating MAGLDR 1.11 to 1.13 make u lose ur warenty. And does someone know when there is gonna be a new MAGLDR 1.14(?) on the market and will this be better then 1.13?

warranty? I think you can reverse and go back to stock for warranty. you already lose your warranty once you flash hspl anyways.
Sent from my HTC HD2 using Tapatalk

magldr 1.11 to 1.13
I'm trying to update from magldr 1.11 to 1.13 but every time I run the ROM update utility I get "Error [260]: Connection" & "the Update Utility cannot connect to your PDA phone." I have the tri-color bootloader screen, as well as USB on it. I'm already running a NAND Froyo build, just trying to switch to Gingerbread. I've tried searching this forum & the web for help without any success. Any help would be appreciated, thanks!
Angelo

Related

[Q] Problem while flashing Nand Android on HD2---won't reboot after Go Go Go! screen

So i used this *thread* to flash the android Nand on my HD2 and i followed all the steps, and then i ended up with a screen as below
123456
GO GO GO!
Typically it is supposed to reboot and go to the Android screen. But it didn't and now it is stuck. I tried hard resetting with power and volume button but no luck and infact none of the buttons work. Even i took the battery out but it comes back to the same screen.
So how do i go back to the WIN 6.5 now. PLzzz somebody help me. I'm sure somebody must have same problem coz i saw in some post that couple of people had the same problem.
PLZ help!!
dude, to go to magldr menu hold end key while booting, and to get to the bootloader to be able to flash a winmo rom, just hold volume down key while booting.
GOGOGO! issue was solved on magldr 1.11, do you have magldr 1.11? If you don't just flash it when you're on bootloader (rainbow screen).
ok. i downloaded the V1.11. But i don't see the tricolor thing. all i see is the Boot Menu with 10 options on it. and when i tried to flash it the connection was unsuccessful. My PC won't connect to the phone then how would i flash it??
patelk3 said:
ok. i downloaded the V1.11. But i don't see the tricolor thing. all i see is the Boot Menu with 10 options on it. and when i tried to flash it the connection was unsuccessful. My PC won't connect to the phone then how would i flash it??
Click to expand...
Click to collapse
you should:
power-off device
press the vol- button and power button together.
then flash 1.11
good luck
Maybe you can help me aswell?
I've tried flashing cmn 6.1 and it works (followed all steps of guide: i have magdlr 1.11, hardspl 2.08 and radio on my dutty rom 2.15.50..). So now i have cmn 6.1 nand. But if i try to repeat the same with Cotulla's Nand or MDJ's - i stuck on error:
Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
I get it once i connect usb cable to usb flasher (it says usb is connected) and launch daf.exe and press 2 times next till it starts checking if phone is connected. Any suggestions how to solve it? Please, help me
May be just reconnect USB cable.
But first make sure that in PC's device manager You have uncheck Save energy option ( it lets to turn off USB port for energy savings)
Sent from my HTC HD2 using XDA App
BimBooTheGreat said:
Maybe you can help me aswell?
I've tried flashing cmn 6.1 and it works (followed all steps of guide: i have magdlr 1.11, hardspl 2.08 and radio on my dutty rom 2.15.50..). So now i have cmn 6.1 nand. But if i try to repeat the same with Cotulla's Nand or MDJ's - i stuck on error:
Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
I get it once i connect usb cable to usb flasher (it says usb is connected) and launch daf.exe and press 2 times next till it starts checking if phone is connected. Any suggestions how to solve it? Please, help me
Click to expand...
Click to collapse
You get that error if you don't run DFT as administrator. Right click on the file, run as administrator.
Sent from my HTC HD2 using XDA App
Thanks guys. It worked and now i have android on my HD2 which i love.
But there is a small problem with it. My data connection won't work, the wifi does.
Any ideas??
patelk3 said:
Thanks guys. It worked and now i have android on my HD2 which i love.
But there is a small problem with it. My data connection won't work, the wifi does.
Any ideas??
Click to expand...
Click to collapse
Go to the FAQ link in my signature, there you will find the TMO APN details which you need to enter manually.
What rom you install?
What rom you install?
Some roms no get data or mms in T-mobile US
neowolfx said:
What rom you install?
Some roms no get data or mms in T-mobile US
Click to expand...
Click to collapse
They should, it's just that you need to manually enter the APN details.
i tried entering the APN manually and it worked.
Thank you everyone for the help.
Android is so much faster and better...just wow. I'm lovin' it.
BTW i used the instructions given on this blog
I got the same thing, nothing after the go go go. I just rebooted my phone and it loaded fine. Only issue I have is the G-sensor freeze. Love this build though!
Sent from my HTC HD2 using XDA App
Help Help Help
I followed a video, flashed my phone, ran the dft and it says it was successful. Now when it rebooted itself, it would boot, but only to the dft screen and then cut back off and do the same 1234 go go go. please tell me what im missing. i know im close but damn im ready for android already lol please help.

install MAGLDR 1.13 on 1.12?

HI!
Well i have installed MAGLDR 1.12 before and had NAND. BUt now i want to try out CWM, and need 1.13.
But how do i update to 1.13? i tried to just run the ROMUpdateUtility.exe, but it cant find my phone. so i cant install it.
please help me asap!
the same way you installed 1.12 the process is the same
man, i just told you all, that ive tried to run the ROMUpdateUtility.exe, but it doesent find my phone.
please try to help me!
dont just say "you just update.." or something that doesent help.
Do i really have to reinstall Windows again?
im a genius so i solved it myself!
just hold VolDown + onbutton - to go to bootloader.
then connect the usb, and flash the MAGLDR
no you just did what you did intially to put magldr on, as per what i said
i think 1.13 batter.
if you cant do the update through bootloader or anything the you have only one option left reflah a stoch rom and then do it
Richy99 said:
no you just did what you did intially to put magldr on, as per what i said
Click to expand...
Click to collapse
Why would you even bother to give such a HELPFUL post? Obviously if he remembered how to flash MAGLDR he would of done it. It's not hard to just say to boot to HSPL and do it...
Sent from my HTC Vision using XDA App

[Q] htc hd2 rom to wm7.

can anyone help me? i tried to change my phone to lower rom version like was said needs to be installed on phone and needed to install windows mobile 7 on the htc hd2 phone and it keeps going to rom installation failure screen and rom installation recovery why wont it work help what do i need to do also it was the dark forces team rom update utility.
bobbymd said:
can anyone help me? i tried to change my phone to lower rom version like was said needs to be installed on phone and needed to install windows mobile 7 on the htc hd2 phone and it keeps going to rom installation failure screen and rom installation recovery why wont it work help what do i need to do also it was the dark forces team rom update utility.
Click to expand...
Click to collapse
Can you be more specific about what ROM you are trying to install, and how you tried to install it? Also, do you have HSPL amd MAGDLR installed on your phone?
If you can provide more specific details it will be easier to understand what is happening with your phone.
ok thanks its the madglr rom to set up the phone for next step in installing wm7 on the htc hd2 its the custom ruu version 2.15 for install on phone and its not going through
bobbymd said:
ok thanks its the madglr rom to set up the phone for next step in installing wm7 on the htc hd2 its the custom ruu version 2.15 for install on phone and its not going through
Click to expand...
Click to collapse
From your description it is quite hard to understand what your are attempting to do. My guess is that you are trying to install a Windows Mobile ROM before installing WP7. If that is the case, then you should be installing the Windows Mobile ROM when you are at the tri-colored bootloader screen. Turn on your phone with the volume down key pressed to get to this screen. Connect your phone to your computer, wait til you see "Serial" change to" USB" and flash your HD2 with the desired Windows Mobile 6.5 ROM
im trying to flash from 6.5.3 to wm7
bobbymd said:
im trying to flash from 6.5.3 to wm7
Click to expand...
Click to collapse
Are going into the MAGDLR screen options when booting and choosing option 5 USB Flasher before connecting your phone to the computer? Also what version of HSPL are you using? WP7 doesn’t support HSPL3.03/OSPL3.03. You need to select HSPL2.08 to run WP7 and MAGLDR.
im not seeing that screen and options for option 5 usb flasher im getting the rom update utility screen on my pc its 3.27.4.0 version madglr
bobbymd said:
im not seeing that screen and options for option 5 usb flasher im getting the rom update utility screen on my pc its 3.27.4.0 version madglr
Click to expand...
Click to collapse
You must install MAGDLR on your phone before you can flash WP7. When it is installed on your phone, hold the power button when you see the MAGDLR screen while booting the phone, and then you can choose option 5.
i tried doing the install of madglr on phone and it keeps failing it wont update phone it goes into the update recovery screen and says to unplug from pc etc
bobbymd said:
i tried doing the install of madglr on phone and it keeps failing it wont update phone it goes into the update recovery screen and says to unplug from pc etc
Click to expand...
Click to collapse
Hmm, did you install HSPL2.08 on your phone before trying to install MAGDLR?
yes and both wont go through they both fail
bobbymd said:
yes and both wont go through they both fail
Click to expand...
Click to collapse
Try changing USB ports on your computer, you might have a hardware driver problem. Also, use a USB port on your computer, not on a hub.
ok i will try that and see and get back
bobbymd said:
ok i will try that and see and get back
Click to expand...
Click to collapse
Okay, I have to get offline soon, so good luck. Check device manager on your computer to make sure the driver is installed correctly.
ok tried that and got the same thing i tried a 3rd port on my pc the device driver installed properly it said and still got the same thing dont understand whats happening and it seems in videos i saw on different sites it happens easy for them i dont get why it wont work for me??
Perhaps others may have an idea. On my T-Mobile HTC HD2 everything installs easily
Sent from my HTC Glacier
ok thanks bud
You are welcome. Other than the driver not installing correctly when you are in the bootloader I am not sure what could be your problem.
I am sure others will have more ideas for you. Good luck.
Sent from my HTC Glacier

[Q] Htc HD2 wont reboot (Magldr and CLK)

After flashing HSPL 2.08, i installed magldr on my device. But when i install an Android or Clockworkmod Recovery, the installer repartitions the device. But after this step there stand "reboot" but it wont reboot. I must then pull off the battery and restart the phone. But ten the phone is stuck in Magldr or in Clk.
Plss heeelp me!
Thank youu
XxxXxx896 said:
After flashing HSPL 2.08, i installed magldr on my device. But when i install an Android or Clockworkmod Recovery, the installer repartitions the device. But after this step there stand "reboot" but it wont reboot. I must then pull off the battery and restart the phone. But ten the phone is stuck in Magldr or in Clk.
Plss heeelp me!
Thank youu
Click to expand...
Click to collapse
Well first clockwork mod recovery must be installed to install android in both clk and magldr ..
Sent from my Transformer TF101 using xda premium
kylew1212 said:
Well first clockwork mod recovery must be installed to install android in both clk and magldr ..
Sent from my Transformer TF101 using xda premium
Click to expand...
Click to collapse
Yes I did this, but it wont reboot, the device cant exit magldr. i must pull of the battery, but then it stuck on htc splash
i think u have the same issue as me ...i cant reboot too ...in magldr it stuck on 123456 go go go ...and in clk it gives an error ...but the probleme disapear on windows ...try to flash wm ...if it's ok than its soething with android and u cant do nothing about ...i tried everything ...and no solution ...
mootmetal said:
i think u have the same issue as me ...i cant reboot too ...in magldr it stuck on 123456 go go go ...and in clk it gives an error ...but the probleme disapear on windows ...try to flash wm ...if it's ok than its soething with android and u cant do nothing about ...i tried everything ...and no solution ...
Click to expand...
Click to collapse
another problem is that I cant flash back to WM. It is stuck at the HTC Logo.
I flashed with sd-card and bootloader and with the installer on the pc, but no way it wont boot and theres no R G D at the buttom of the screen when the htc logo appears. pls help me ...
Is it possible that my memory blocks are damaged ?? because clk says: "Error cannot read recovery Header" and then it is stuck .
What radio are you using?
Sent from my NexusHD2 using xda premium
have you tried the "task29" with hd2 toolkit?
Same problem over here Impossible to reinstall WM, because task29 stops installing at 96%
kylew1212 said:
What radio are you using?
Sent from my NexusHD2 using xda premium
Click to expand...
Click to collapse
Iam using Radio Leo 2.15.50.14
ericw13 said:
have you tried the "task29" with hd2 toolkit?
Click to expand...
Click to collapse
Yees very often... i used task 29 every time before i flashed a new rom.
When you are using "task29", you stay still stuck on 96%??
if so, I suggest you try another USB port on your pc.
otherwise, your menu "magldr", it is functional?
Already tried to put it in another USB Magldr is functional, but I don't know what to do with it.
ericw13 said:
When you are using "task29", you stay still stuck on 96%??
if so, I suggest you try another USB port on your pc.
otherwise, your menu "magldr", it is functional?
Click to expand...
Click to collapse
No at me task 29 isnt stuck. and yes magldr is functional. but i need recovery to flash rom. first i entered usb flasher and all works fine, but then there stands: "Resetting phone" But it wont reset i must pull off battery !
XxxXxx896 said:
No at me task 29 isnt stuck. and yes magldr is functional. but i need recovery to flash rom. first i entered usb flasher and all works fine, but then there stands: "Resetting phone" But it wont reset i must pull off battery !
Click to expand...
Click to collapse
are you sure to have applied the correct partition settings. false if the rom is stuck on a screen. what is the rom you want to flash?
ericw13 said:
are you sure to have applied the correct partition settings. false if the rom is stuck on a screen. what is the rom you want to flash?
Click to expand...
Click to collapse
So far no rom because i cant flash the clockworkmod. there it wont reboot
XxxXxx896 said:
So far no rom because i cant flash the clockworkmod. there it wont reboot
Click to expand...
Click to collapse
by flashing with hd2 toolkit, you have errors that appears in the application?
ericw13 said:
by flashing with hd2 toolkit, you have errors that appears in the application?
Click to expand...
Click to collapse
No all is fine there is no error... the phone dont want reset... and i tried mtty (cubexe said to me) and there stands that the phone has some bad blocks but no way to erase them or to mark them, i really tried all tipps i have read...
i think the nand memory (hardware) is totally damaged...
searching on the net, I came across this software YAFFS nand explore. it is apparently able to correct the problem of "bad block" on Android phone, a view!!
Sent from my NexusHD2 using XDA App
ericw13 said:
searching on the net, I came across this software YAFFS nand explore. it is apparently able to correct the problem of "bad block" on Android phone, a view!!
Sent from my NexusHD2 using XDA App
Click to expand...
Click to collapse
Thank you for your answer. but i cant use this because its a app and i cant boot into android.. there is no OS on my htc hd2. i cant install any OS the bad blocks are at the beginning, in the middle and at the end of the nand memory i think there is no system which is so small to boot into. a tool for pc which correct the bad blocks would be very usefull but i tried it already with mtty and i think its made for htc devices and this tool cant erase / repair /mark the blocks... i dont know if there i another tool which can repair this... but if you know some other tools for pc pls tell me ))

[Q] MAGLDR 1.13 stuck GO GO GO!

HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
hold power button until magldr menu appear
in ad recovery you can wipe anything
Pentuni said:
HI there so i bought a used HD2 wich came with ICS installed when it arrived i turned it on and loaded MAGLDR then it tried to load Android but got stuck at the GO GO GO! line. As i dont have any drivers installed and Windows doesnt recognize the HD2 in MAGLDR i cant flash a new rom. I wanted to do a Task 29 but that requires drivers too.
So my question is how do i perform a full wipe so i can get a working rom since the phone turns on, shows the TMobile splash screen then goes into Magldr and tries to boot android immediately then get sutck in GO GO GO!.
Click to expand...
Click to collapse
good to know u want to start from scratch...u ll never know wats been put it that device... ....here is wat you can do
i had put out these steps in another thread to help out a fellow XDAian... try
files you need: (if you need pm me)
-task29
-Radio Leo 2.15.50.14
-DFT_LEO_MAGLDR113_DAF
-Recovery_150M_system_5M_cache
-rom zip (dont alter/extract zip if you done know wat to do with this)
do these: (from your current WP7 rom)
-restart device
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-do a task 29
-get into bootloader again
-plug usb...hd2 should say 'USB'
-install radio by running 'CustomRUU.exe'
-get into tricolor bootloader
-plug usb...hd2 should say 'USB'
-run DAF.exe for installing MAGLDR
-reboot
-get into MAGLDR by holing power/end key while booting
-go to 'usb flasher' in the menu and press green/call button
-plug usb...hd2 should say 'USB'
-wait till it say 'wait usb...usb'
-get into your recovery folder
-run daf.exe
-reboot post completion
-get into MAGLDR by holing power/end key while booting
-get into ad-recovery
-get into mount storage
-activate usb mass storage
-now put the rom zip files into sd card
-press power to get back to recovery menu
-select install rom from sdcard
-choose rom file
-select install
this should typically install nandroid into your hd2...
if you face any issues, share the step and the error scenario/msg
I tried to get task29 but my PC doesn't recognize the hd2 even on bootloader.
Sent from my MB860 using xda premium
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
It's better if you download the drivers because it's useful for later needs...
Best regards
Sam Razzy...
Sent from my HD2 using xda premium
Pentuni said:
Edit: So i managed to get the drivers and got the phone recognized, so i performed task 29, worked perfectly. Followed the steps but when i try to install a radio it fails and gets stuck at 96%. I tried flashing the radio several times but no luck... What am i doing wrong?
Click to expand...
Click to collapse
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
gdsbalaji said:
can u provide more details....actually as much details on the hd2 (eu/us), hspl, radio version, your process on how u tried etc...we will help you solve this.
Click to expand...
Click to collapse
I have the T Mobile US version, HSPL SPL-2.08.HSPL 8G XE COtullaHSPL 0x05 0x50(what it says on tricolor bootloader). The radio i tried to install is 2.15.50.14.
I got the drivers, my PC finally got a connection with the HD2 so i performed a task29 and wiped the phone then i followed your guide tried to install the radio but the process with CustomRUU.exe got stuck at 96% and said there was an error "this update utility can not be used on your device." and now the phone shows an Update Fail screen without a radio i cant install MAGLDr then install WP7 on it so what can i do?
kylew1212 said:
Their is a guide in my signature, its got basically everything you need to know. If you have problems post on there or pm me. I will gladly help.
Sent from my HD2 using xda premium
Click to expand...
Click to collapse
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Pentuni said:
Thank you i read your guide. So can i instal clK without a radio? Also can i install ICS beta10 or Windows Phone 7 with cLK and witout going through the radio installation?
Another thing... the came with almost no battery and i cant charge the phone with the update failed screen i saw that i need at least 50% of battery but i dont think the phone has that much.
Click to expand...
Click to collapse
Okay sorry I should've explained more..
yes you have to have a radio.
Yes you can install ics beta 10 with clk.
No you cannot install wp7 with clk magldr is required for that.
If your phone is getting close to running out of battery I would flash clk 1.5 via SD card and then charge the phone up
Sent from my HD2 using xda premium
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
I'm having the same problem until today.
Did a task29, installed magldr, cwm, then a rom, radio is 2.15.50.14.
It can boot to CWM, it can reinstall the rom but it's gets stuck in the go go go after restarting.
Please help
TIA
I know how to use magldr, but not tons about it.. also I think you guys should post in the wp forums someone there may be better help
Sent from my HD2 using xda premium
Pentuni said:
Ok so i got the radio installled and proceeded with the process with magldr installed fine and i followed this guide to get WP7.
http://forum.xda-developers.com/showthread.php?t=1246040
After the installation the phone syas reboot now! but doesnt do anything i had to pull out the battery and now it wont boot. ts stuck in a blank magldr menu.
EDIT: I managed to get magldr to show something, it tries to boot WPH but says 1eFATAL HIT 1. Did i scre up the installation? If i hold the power button it keeps doing the same thing without showing the options menu how do i wipe the rom so i can flash a new one?
Edit 2: flashed wp7 again boots magldr then sticks on GO GO GO! again.
Click to expand...
Click to collapse
Its happened to me before. Make sure as soon as you flash magldr, thats you clear mbr on sd card and use last 24 nand, and you will be fine, otherwise you will stay stuck on go go go go
good luck!
Yep.. thats a problem for you, but also for me, i have HTC HD2 fully working, just replaced digitzier soon, WinMo just works flawless thought it sucks ballls, and whenever i try to do task 29 then install radio then install magldr then install cwm with the required partition, i get stuck on GO GO GO! ..

Categories

Resources