i've managed to get my mt4g taken apart, however, i can't seem to get the LCD and digitizer to come loose of the front housing. I've searched all over for information about this but haven't been able to find anything. Does anyone know how this is done?
Related
Hello all,
My Touch HD slipped from my hands and ended-up flat on the screen... the screen does not have a scratch, the digitizer still works perfect, but the LCD underneath is broken, so I get a black screen. I can still access the Touch HD via my PC thanks to MyMobilier, though (so why do I complain, huh?!!)!
I ordered a replacement LCD in Hong-Kong (thanks ebay!), got the HTC Service Guide, managed to remove the antenna cover (tough!) and dismantle the whole thing. But NOW I AM STUCK with the 'bezel', i.e. the cover, screen, digitizer, LCD, and metal plate with bolts all apparently glued together.
Anyone faced the same problem? Anyone knows how to separate the LCD from the screen and digitizer?
Cheers,
FroggyZ
Up
Anyone can help with this???
My touch hd has a faulty LCD screen, and I've bought a new LCD screen spare part, just so I could replace it myself. I'm trying to change the LCD to the new one, but am having problem removing the old LCD from its front housing. Could anyone help me with this? I've removed all the screws, and tried to pick on the side to remove the LCD, but have failed to remove it.
Thanks in advance!
This is my first post here and though i read similar posts on this subject i would
like to read your opinions on this one.
I accidentally dropped some water on my touch hd and my display got damaged.The phone worked fine and so did the digitizer but the problem was that the backlight of the display was dead.At some point the backlight turned on but when i tried to input the unlock code it turned off right away (did this several times).I knew that i should replace the lcd (and the digitizer just in case).
I bought the lcd and the digitizer seperately and i managed to assemble the phone back using the service manual.Since then when i turn the phone on I hear the starting sound,i get the vibration then after a while the screen with no backlight again displays the "tap here to configure your phone" screen (after the hard reset),when i tap i get no response.
I checked the connections many times and i also used a second digitizer with no success.
Is there a possibility flashing a new ROM will solve the problem?
If so is there a way of flashing a ROM when the phone's screen is not usable?
Waiting for your precious opinions/suggestions/knowledge
Thanks in advance.
Hello,
Flashing the ROM won't solve an obviously hardware problem.
If you changed the LCD and still have no backlight, then either you bought a defective screen, or the problem is elsewhere, maybe on the main electronic board... Which would be bad news.
BTW, I wanted to change the digitizer in the apst years, but its not provided with the glue, so I had to buy a whole assembled screen + digitizer.
How did you manage to glue the digitizer on the screen ?
I aligned the screen with the digitizer and then i used small pieces of a special thin and trasparent tape to hold it in place.The tape holds the screen tight and it is barely visible, it also has the advantage that you can seperate the lcd and digitizer anytime you want with ease (though you have to be very delicate when applying it to get a good result)
I asked for a replacement of the defective lcd and i hope i will get a new one.
I have an HTC HD2 which had a cracked screen. I repaired it with a new screen, but I don't know how to adhere the screen to the chassis. What is the proper way to do this?
I tested it, and everything works now...but the screen stands off the chassis too far. It's not sandwiched down enough, so the talk/end etc buttons don't have enough travel to activate the pcb below them.
Can someone give me some advice? Thanks.
Hi everyone,
Yesterday I checked that gorilla glass 3 is a big ****. Now I have my op2 working but with some scratches in the external screen. Touch is OK and the LCD is also OK, but I want to change it because I suppose that with a little pressure over the screen it will broke definitely. I'm looking for a digitizer replacement but I only find people changing both: LCD + Digitizer.
I've found that http://vifocal.com/lcd-digitizer-display-touch-screen-assembly-replacement-for-oneplus-2-two-smartphone.html and it is ridiculously cheap for a LCD + digitizer, so I want to be sure that for the op2 the way to change that part is completely changing the lcd and the external screen. It's that true?
Thanks.
Yes the easiest and best way fix screen issues is to change the entire combo.However if you search you will also find only front glass replacements without the LCD for a much cheaper price($3-4).....
parts4repair.com/front-glass-for-oneplus-two
....but again that requires professional tools for replacement and you need to play with loca glue while reinstalling and the process is relatively difficult and not everyone can do that.