Repaired cracked screen...how do i glue it in? - HD2 General

I have an HTC HD2 which had a cracked screen. I repaired it with a new screen, but I don't know how to adhere the screen to the chassis. What is the proper way to do this?
I tested it, and everything works now...but the screen stands off the chassis too far. It's not sandwiched down enough, so the talk/end etc buttons don't have enough travel to activate the pcb below them.
Can someone give me some advice? Thanks.

Related

touch screen problem

hi my wizard touch screen barely works now im hoping it is only the makeup my wife has gotten into the sides. I have it taken apart now and cleaned up but the is ablack spot on the cable for the digitizer I think that's what it is the screen ontop of the lcd. if the digitizer is bad is there any way to tell before I put it back together again. its just a small dot not near the copper part. any help would be appriciated. thanks!!!
anyone????

Broken LCD

Hello all,
My Touch HD slipped from my hands and ended-up flat on the screen... the screen does not have a scratch, the digitizer still works perfect, but the LCD underneath is broken, so I get a black screen. I can still access the Touch HD via my PC thanks to MyMobilier, though (so why do I complain, huh?!!)!
I ordered a replacement LCD in Hong-Kong (thanks ebay!), got the HTC Service Guide, managed to remove the antenna cover (tough!) and dismantle the whole thing. But NOW I AM STUCK with the 'bezel', i.e. the cover, screen, digitizer, LCD, and metal plate with bolts all apparently glued together.
Anyone faced the same problem? Anyone knows how to separate the LCD from the screen and digitizer?
Cheers,
FroggyZ
Up
Anyone can help with this???

Replacement of the screen unit

HI there,
I need to replace my screen, so I ordered a complete unit (LCD Screen, Digitizer and front). Now, I have to problem how to fix it onto the housing. They used biadhesive tape, but when I first tried it, the screen did not react when pressing the buttons, for example. I had to press very hard until it reacted. So I guess, the distance was not high enough, wasn' it?
How do I glue in the screen? Which tape to use? How to center it?
Does anyone know which tape HTC uses?

hd2 screen replacement problem...tape issue?

i cracked my digitizer a while back, and ordered a replacement. i used double sided tape to install. the first digitizer worked great, except only the top 10% of the screen was not responsive (pretty much the width of the task bar) so i contacted the people i ordered the new screen from, and they just sent me a replacement. i installed the second digitizer, and this time none of the screen works.
i tried to make sure both times not to put the tape to wide so it doesn't overlap into the clear screen part, only the black, but could this be a tape issue? anyone else have trouble with installing where parts or entire screen didn't respond?
thanks for your help.
Are you sure you have the digitizer/lcd ribbon in all the way to the connector on the motherboard? When I first put everything back together when I changed a digitizer, touch didn't work at all for me initially. At first I thought I had a bad digitizer. Then I looked closely at the ribbon and connector, and there's some flaps that stick out to the side on the ribbon cable. Make sure you push the ribbon in until the flaps stop you from going any further.

[Q] Problems after replacing LCD and digitizer. Help needed.

I recently broke my 1 month old S5 LCD. Outer screen is just fine, but the LCD has paper thin glass, and it unfortunately met it's demise after a misplaced toss. I ordered a new LCD digitizer assembly and screen adhesive, then disassembled my broken phone. When I disassembled it there was either adhesive, or gasket material that was on top of the plastic flaps that go around the back and recent buttons (I assume adhesive), and also around the home button which I assume is important for functionality, and for water resistance. To make a long story short I assumed that this material would be provided with the screen adhesive so I removed the material from the back and recent buttons (it was already slightly damaged on one, and almost all peeled off of the other. I left the home button material because it seemed weak and I didn't want to break it. Also, some of this material had been peeled off/torn off surrounding the home button. After reassembling without the adhesive/gasket in these areas my phone now presses back or recent at random and it makes the phone almost impossible to use because it will exit out of programs or just start doing crazy stuff all on it's own.
My question is, is there somewhere that sells the adhesive/gasket for these three locations, if so where, and if not are there any suggestions of an alternative to the stock material. I am wondering if anyone has had some experience with this issue could chime it. I greatly appreciate any help.
Sincerely,
Dustin

Categories

Resources