It was the second time replacing the housing on my Touch. I was a bit careless when putting it back together. I broke the slider button on the side. Can anybody tell me where I can get a replacement??
You try ebay? I found my speaker on ebay and it was only $5.50+free shipping straight from China. It took 9 days for delivery
Did you break the slider, or the physical button assembly on the PCB?
My camera button housing broke (not the button itself), so I had to open my Vogue, tear it out, and now I have to press a tiny phillip's screwdriver against two contacts to get my phone to boot to the bootloader.
Hopefully you haven't wrecked the PCB and can find a suitable replacement.
Shidell said:
Did you break the slider, or the physical button assembly on the PCB?
My camera button housing broke (not the button itself), so I had to open my Vogue, tear it out, and now I have to press a tiny phillip's screwdriver against two contacts to get my phone to boot to the bootloader.
Hopefully you haven't wrecked the PCB and can find a suitable replacement.
Click to expand...
Click to collapse
i just ordered a new housing for my vogue if you need any part of my old one we can arrange that. pm me
Hey im panicing so bad rite now. I just broke my htc's LCD screen ! Mad sad from this disaster . Dont got much money so can someone please tell me whats the cheapest or best way to replace or fix it ? I really need help because im freaking out!
The repair choices
There are basically two choices. Doing it yourself or having it repaired.
In either case the most straight forward is to replace the screen and digitizer as one unit. I expect you can still see things on the screen yet its cracked from one corner. Its the digitizer on the top that usually suffers but its hard to replace by itself. There is a YouTube video showing how to do this (search on Replace Touch Screen on HTC HD2 on YouTube).
If you are game to do it yourself (an electronics tech would be able to do it fairly well, though it is still fairly difficult) then you can buy a complete screen and digitizer off ebay (around $100). Getting the unit out of the case is tricky as its held in with 4xT5 Torx screws (easy bit) and lock notches around the case (tricky part). I found thin stiff plastic bits slotted in between the module and the case works well at releasing the locking notches. Then press out at the top of the battery area, while pulling the top edge of the plastic case out and down with your finger nails. One side at a time. Don't forget to remove the SIM card and SD card as these will hold the module in place if not removed.
The double sided tapes used to hold the screen in place are a problem, but warming them up with a carefully applied heat gun does release them. I would add that there is no need to unscrew any of the electronics boards as the screen can be replaced without doing this. Releasing the screen ribbon cable connector is done by flipping up the black locking section on the ribbon socket. Slide in the new cable, lock it down, then curl it around as you slide it backward under the metal case so that the curl in the cable occurs in that small space under the metal rather than being folded over sharply, which can fracture the ribbon cable "wires" rendering the screen dead.
Press the screen back down onto the tape (hopefully the tape has remained slick enough as its all that holds the screen in place). Be careful to align the edges and top and bottom correctly, otherwise your buttons won't work and the screen will not sit in the case properly. You can test the buttons as you align to feel for the slight click. Be sure to test all four as alignment left to right is just as critical for full function as up and down. You should also watch to be sure the light sensor little plastic bit (its a small clear cube of plastic) doesn't fall out and disappear while you are doing the screen swap and it stays in place during reassembly.
Then press it home into the plastic case. I remove the volume button (if it hasn't fallen out already) as it tends to push the volume button pads out of alignment (they are only held in with yellow tape (be careful not to loose them). Then with it all snapped in place pull out at the volume button section and slot the button back in place. Orientation is fairly obvious with the button points lower down and the joining bar going behind the case plastic to lock it in place (all with the screen facing upward). You may find the volume button only works if you press down on the screen slightly. This movement will be taken up when you screw the 4 torx screws back in.
Finish by powering up (with fingers crossed) and test. Hopefully all working.
Alternatively, if thats put you off doing it yourself, get it repaired by a service agent (around $300). Then it comes back all done with a small warranty. Most of the phone providers will be able to direct you to a good independent service agent.
I have an HTC HD2 which had a cracked screen. I repaired it with a new screen, but I don't know how to adhere the screen to the chassis. What is the proper way to do this?
I tested it, and everything works now...but the screen stands off the chassis too far. It's not sandwiched down enough, so the talk/end etc buttons don't have enough travel to activate the pcb below them.
Can someone give me some advice? Thanks.
i cracked my digitizer a while back, and ordered a replacement. i used double sided tape to install. the first digitizer worked great, except only the top 10% of the screen was not responsive (pretty much the width of the task bar) so i contacted the people i ordered the new screen from, and they just sent me a replacement. i installed the second digitizer, and this time none of the screen works.
i tried to make sure both times not to put the tape to wide so it doesn't overlap into the clear screen part, only the black, but could this be a tape issue? anyone else have trouble with installing where parts or entire screen didn't respond?
thanks for your help.
Are you sure you have the digitizer/lcd ribbon in all the way to the connector on the motherboard? When I first put everything back together when I changed a digitizer, touch didn't work at all for me initially. At first I thought I had a bad digitizer. Then I looked closely at the ribbon and connector, and there's some flaps that stick out to the side on the ribbon cable. Make sure you push the ribbon in until the flaps stop you from going any further.
Hi guys,
I just disassembled my HD2 to replace my broken digitizer and touchscreen.
But now i'm stuck with a problem.
What shall I use to glue both items together again?
And the keyboard makes some issues.
I tried to place both parts over eachother to see if they fit but I can't press the keys after it.
Seems like they are stuck.
That's why I didn't want to use superglue because after assembling it I wouldn't be able to change anything.
Maybe pictures tell more than words.
http://www.youtube.com/watch?v=t8Q7mXdcJ54&feature=player_embedded
hope that helps you
thanks wasn't the information I was looking for but nevermind
I assembled the device now .. but the next problem occured ..
the hd2 is loading without problems (led shows it) but when I try to power it on it's completely dead. nothing happends
with my old touchscreen it was at least possible to power it on.
my question is:
could the new soldered touchscreen + digitizer be broken? or did I break something during disassembly and assembly?
To be honest I didn't see any mistakes I made.
It's not my first time repairing stuff like that because I used to repair notebooks as a hobby.
Still i'm unsure what the heck is going on with my phone atm.
did you check if the flex cable from display is in the port, there is an white stripe that shows how far it must in the port. Did the phone vibrate when you pressed power button?
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
12dollar said:
I checked the cables and found nothing suspicious.
and the phone didnt even vibrate after trying to power it on.
I'm trying to get a new hardkey board (i hope you know what I mean).
Had problems with the keys being stuck and maybe I killed that one by trying to assemble it.
if the phone doesn't recognize me pushing the power on key it's no wonder it won't do anything.
hope this will fix the problem
Click to expand...
Click to collapse
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
bib*oops said:
Most likely something is wrong with your Power button, but you should turn it on with 2nd method:
- pull out battery;
- insert usb cable(connected to PC)/charger in your usb port;
- insert battery.
This way it should turn on whatever OS you have installed on.
If your OS is Android through MAGLDR, connecting it through usb should turn it on by default, unless your battery is not dead!
Check it out!
Click to expand...
Click to collapse
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
12dollar said:
I just did as you said and yeah the phone came to life.
so there is definately a dead power button (probably the board is broken)
Click to expand...
Click to collapse
Glad to hear that!
Definitely you should replace your keypad flex!
Did you fix the problem with the hardware keys
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
maznevh said:
Hi,
I have very similar problem.
I changed the touch screen on my HD2 and after reassembling I cannot get the hardware keys clicked.
I ordered a brand new key board and brand new plastic buttons. I received them but situation is the same.
If somebody can explain is there any trick during adjusting the plastic buttons to the clickable "small dots" on the board - please help me.
Best Regards
Click to expand...
Click to collapse
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Hard to get hardware buttons clickable
Mister B said:
Normally this is always down to glass digitizer not being aligned correctly when stuck to LCD.
0.05mm can make all the difference here.
You need review current digitizer position & pre test assembly to centre chassis without tape for a test run on button function.
Also check button board position is exact & located correctly in the pin holes at each end of the board.
original board quality is normally far better than most of the very cheap eBay pattern parts but one or two sellers offer a decent board around $4.50
Also clean all old tape from back of LCD & centre chassis plate so parts fit flush & once all checked new tape can be added, I also use small spots of up40 adhesive sealant near corners & near middle edges for final build up as holds far better than even the best tapes & gives an original strength & long lasting flush look to final job plus us easily removed with razor blade if repair ever needed again.
Super glue is a BIG no no NO.
Click to expand...
Click to collapse
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
maznevh said:
It is not the case in my case , because I ordered full set (digitizer + display) and they arrived factory assembled.
But you are definitely right - 0.05 mm make the difference. I think the problem comes from the fact that the board with buttons cannot be firmly fixed to the 2 small juts on the chassis. You know the plug of the buttons board is on the tail like extension. Probably when I try to cover the buttons board with the LCD+digitizer - the frame of the LCD slightly pushes the buttons board and the juts on the plastic buttons cannot be fixed exactly on the top of the actual buttons on the board. Anyway we are speaking about precise fixing something around 0.05 mm over something else, which is exactly same size... and in the same time you have to fix this without any visibility.
I will continue trying. If you can give me any other ideas - I will appreciate this.
Thanks
Click to expand...
Click to collapse
Do not rule out the LCD/Digitizer assembly as the china combos are prone to not the best accuracy of assembly as sounds like maybe LCD is mounted just a fraction too low on the digitizer perhaps.
Button board should be fixed via 3M style tape & most replacement boards come with tape ready for fitting.
worth making effort with button board to centre chassis to mount securely then mounting lcd to chassis without tape for a trial assembly & try and check for possible issues such as bent chassis or old tape not removed sufficiently or new assembly alignment not the best.
I would also recommend using original plastic button strip as the copy ones are not always good & have had experience with them before.