Hi Guys
I've been going through the process to try to upgrade to Win 7 but i've hit a bit of a stumbling block and as I'm not very good at this stuff, thought I would ask for advice!
Ok so, I tried to load MAGLDR 112 but that wouldn't load however, I managed to flash 110 from an SD card. So, next step would be to try to "upgrade" this to 112 in prep for WP7.
I have now tried to flash 112 from SD card AND PC RUU but both just "stop". The SD card shows the "Loading..." and then does nothing whilst the RUU shows "0%" and never progresses.
I figured my next step would be to try a stock ROM both via SD card and RUU however, the stock ROM shows exactly the same error.
Any ideas how I can get back to be able to flash NBH's?
Thanks!
usefull(?) info below-
PB81100 HX-BC
SPL-2.08 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
MAGLDR v1.10 boots to "Boot menu" but doesn't seem to do much other than allow me to go through the menus - what is MAGLDR?
Monty Burns said:
Hi Guys
I've been going through the process to try to upgrade to Win 7 but i've hit a bit of a stumbling block and as I'm not very good at this stuff, thought I would ask for advice!
Ok so, I tried to load MAGLDR 112 but that wouldn't load however, I managed to flash 110 from an SD card. So, next step would be to try to "upgrade" this to 112 in prep for WP7.
I have now tried to flash 112 from SD card AND PC RUU but both just "stop". The SD card shows the "Loading..." and then does nothing whilst the RUU shows "0%" and never progresses.
I figured my next step would be to try a stock ROM both via SD card and RUU however, the stock ROM shows exactly the same error.
Any ideas how I can get back to be able to flash NBH's?
Thanks!
usefull(?) info below-
PB81100 HX-BC
SPL-2.08 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x30
MAGLDR v1.10 boots to "Boot menu" but doesn't seem to do much other than allow me to go through the menus - what is MAGLDR?
Click to expand...
Click to collapse
I hit a similar problem earlier where on the bootloader it kept on saying NO SD CARD. You may try and follow this solution, I suggested earlier. Click here
The first and third step are quite important. Some others have tried to do it quickly and sometimes it has not worked so give them full consideration.
Let us know if it worked.
Cracked it thanks. Turns out I had put a "normal" SPL on and not the HARDSPL... reflashed with HARD and all working.
Thanks
Monty Burns said:
Cracked it thanks. Turns out I had put a "normal" SPL on and not the HARDSPL... reflashed with HARD and all working.
Thanks
Click to expand...
Click to collapse
Good good. Have fun mate.
Related
I have on the screen:
PB981100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x40
I have tried to uninstall it with a instructions where I rename the file to Leoimg. But it only starts on the screen with the colours, it's not loading. What are wrong? I must have my phone on service and when it got there I got som error from them and they say I have installed some illegal rom, I don't understand nothing, but maybe this is what they meant. Please help, I want to unintsall this.
You don't need to flash an official rom from SD card to uninstall HSPL.
Run HSPL2 and select an original SPL.
Yes, but i get error
I get error when I run hspl2. I got some usb connection error. What's wrong?
Simpfan said:
I get error when I run hspl2. I got some usb connection error. What's wrong?
Click to expand...
Click to collapse
Try to run HSPL2 as administrator
Good luck
If you still wanna try through the SD Card, the filename has to be LEOIMG.nbh and in the root of the card. After first tricolor screen, it should read the file and present you a white background screen with option to flash the stock ROM.
The menu comes with a flash
I got loading, but it only flashes and not going to a menu. It only says loasing and goe's back to my color screen. i have to remove the battery back to get the colour screen removed.
Problem with the card...its not reading the file...the card has to be in FAT format...NTFS doesnt work...whats the size of the card ?
Card is
Card is a 8 gb fat 32 card and are formatted correctly. have tried other cards but the same thing happens. but I have uninstalled the hspl i think, it not says hspl on the colour screen anymore. i run the hspl2 as administrator. Thanks for the help everyone.
Hi all ^^
I'm new here, and I just received my HD2 and wanted to flash it with one of the cool ROMs you have on this forum.
I flashed the HSPL with HSPL2 and everything went smoothly. Then I downloaded one of CleanEX DSE Core Rom (the 6.5 Maniless FRE) to be precise.
I flashed it, all was good, at the end the phone rebooted and i was stuck at the boot screen written "HTC CleanEX UDT DsE Series". I thought maybe it was because I didn't do a hard reset yet. So i did one, everything initialyze and when it's done same thing, the phone reboot and I'm stuck at the same boot screen...
I'm starting to get a bit stressed out because if I can't connect to Activesync I can't even put an original Rom or an other twinked one ><
Does anybody know what I did wrong or why it's not working ?
Thanks in advance for your answers.
PS: My phone is a french phone.
radio - go back and reread that roms thread for recommendation, however 2.07.50.x or higher should do it.
boot to bootloader, connect usb, flash radio, phone will now boot
Connect your phone to PC and turn it on while holding volume down, bootloader menu should apear (red,green,blue,white) then you can run Rom flashing tool on your PC
but i recomend flashing newer RADIO because this may be the reason for your current issue.
That was a really quick and effective answer !!
Thanks a lot to both of you !!!! *hugs*
its seriously the radio
DN41
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
smrazi said:
I tried to install HSPL but unfotunately it stops & my phone is not working. My HD2 hangs when HTC logo comes. I also try to copy stock ROM in SD card whilst pressing voldown & power keys, tricolour screen appeared & says:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Then the phone hangs.
Could anyone tell me what is ROM flashing tool & what version should I install.
Please help me.
Click to expand...
Click to collapse
are you flashing the ROM on a different micro sd card? you cant use a 8GB or 16GB. Try a smaller card like a 1GB or 2GB.
also rename the stock ROM to LEOIMG.nbh.
put that ROM file on a smaller card and go into bootloader should come right up. worked for me when i had to re-install stock to return defective unit.
/edit: Got it to work, had to format the SD card from the phone
I've been searching for an answer for this for hours and haven't seen anything here or elsewhere so my apologize if I've missed it (a little bug-eyed now)
I had to replace my HD2 due to the touchscreen no longer working so I'm trying to roll back the phone to its stock status but I cannot for the life of me remove the HSPL. I've followed the instructions and put the RUU_SIGNED.NBH (renamed to LEOIMG.NBH) onto an SD card and started the phone by holding down the volume down button. It boots into the bootloader screen but nothing else from there. Its like it doesn't see the file on the SD card to flash the rom back to the shipped version.
Right now the screen says
PB81120 HX-B3
SPL-2.08 HSPL 8G XE
0x05
CotullaHSPL 0x40
Using the RUU_SIGNED.NBH from this file: RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50.07U_2.08.50.08_2_Ship
What am I missing here?
how did you make it at the end?
9
Hey all,
A friend of mine tried to install android on his HD2.
After installing HSPL it worked fine.
But after flashing MAGLDR the phone gets stuck at the HTC bootscreen.
And I cant get the phone connected to activesync
What did I try:
1. Hard Reset
2. Using a stock rom RUU (ruu_signed.nbh)to flash like this:
a)Formatting the sd card to fat32(16GB)
b)Putting ruu_signed.nbh on the sd card and renaming it to leoimg.nbh.
(I tried the Unbranded and the NLD RUU)
c)Turning phone on with vol down.
After the thrid step (c) I get on a screen that says "Loading..." but after 30 minuts nothing happen.
Anyone! What do I need to do?
Greetz,
Michka
BTW i got my ruu_signed.nbh files from the %temp% folder of the RUU installer.exe
This is what he gets on the tripel color screen.
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
The SD card should be freshly formatted, FAT32 format.
It´s not easy to find out what went wrong with MAGLDR.
Did you use the latest version, 1.13?
What HSPL and what Radio ROM version were on the device?
And finally, do you still get into the bootloader screen (vol. down + power),
what does it say in there?
tictac0566 said:
The SD card should be freshly formatted, FAT32 format.
It´s not easy to find out what went wrong with MAGLDR.
Did you use the latest version, 1.13?
What HSPL and what Radio ROM version were on the device?
And finally, do you still get into the bootloader screen (vol. down + power),
what does it say in there?
Click to expand...
Click to collapse
Yes i used the latesd version o MAGLDR,
HSPL 3
Radio dont remember
Yes i can get in the bootloaderscreen.
Well, then please provide as much information as possible.
It´s really hard or even impossible to help without more information.
It´s a bit like: My car is broken. What should I do?
"A stock ROM" is very tight information...
For your reference, flashing through SD card deletes HSPL, that´s why I asked
what the bootscreen information says...
tictac0566 said:
Well, then please provide as much information as possible.
It´s really hard or even impossible to help without more information.
It´s a bit like: My car is broken. What should I do?
"A stock ROM" is very tight information...
For your reference, flashing through SD card deletes HSPL, that´s why I asked
what the bootscreen information says...
Click to expand...
Click to collapse
Oke if someone could help me I will provide some info tomorrow.
(I need to ask my friend cus i havent got the phone in my possesion)
This is what he gets on the tripel color screen.
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Sent from my HTC Wildfire using XDA App
Bump
Sent from my HTC Wildfire using XDA App
See, the information you posted is helpful indeed.
You still have SPL 2.08.0000 on your device instead of 2.08.HSPL. On the other hand, I still don´t know what your original ROM was.
Please try to re-install with HSPL3.exe, and please make sure to install the correct Radio ROM in case you don´t have it yet, should be 2.15.50.14.
Both items are required to run MAGLDR properly.
If your attempt to flash a stock ROM failed, then something else was wrong.
There are known problems flashing with 8GB, or greater, SD Cards.
Put the phone into Bootloader Mode and then connect to the PC.
Run HSPL3 and select 2.08.HSPL
Put the phone into Bootloader Mode and then connect to the PC.
Download and flash the RADIO 2.15.50.14.
Put the phone into Bootloader Mode and then connect to the PC.
Now you are ready to go through the MAGLDR instructions and NANDRIOD flashing.
fred_up said:
There are known problems flashing with 8GB, or greater, SD Cards.
Put the phone into Bootloader Mode and then connect to the PC.
Run HSPL3 and select 2.08.HSPL
Put the phone into Bootloader Mode and then connect to the PC.
Download and flash the RADIO 2.15.50.14.
Put the phone into Bootloader Mode and then connect to the PC.
Now you are ready to go through the MAGLDR instructions and NANDRIOD flashing.
Click to expand...
Click to collapse
Thanks for adding that hint, I keep forgetting this very fact.
I do have the 2GB card which came with the device ready for flashing purposes... it was even my Goldcard at very early stages.
Oke thx for the replies.
I will try it tonight!
Greetz,
Michka
Sent from my HTC Wildfire using XDA App
Thank you guys.
The problem was hspl.
Because of the sd card (i think) hspl wasnt flashed right. So i couldnt install a radio or get magldr working. Now i reinstalled hspl and i can do anything.
So what i did in short:
1. Reinstalled hspl 3.00 with a 2gb sd.
2. Flashed the right radio.
3. So now magldr was working
4. Flashed the nld stock rom(to be 100% sure everyting works).
5. Reflashed magldr 1.03 again.
6. Flashed an android disre hd rom (standard nand rom doesnt seem to work).
7. We are happy everything works.
Thx again!
Sent from my HTC Wildfire using XDA App
trying to put this rom on my phone -http://forum.xda-developers.com/showthread.php?t=1080950
but i feel like and idiot bc for some reason my phone says LEO1000 and it says in i cant get that rom without being LEO1024...I dont know very much about roms& spl's but i can follow instructions pretty well. Please help!
Something tells me i cant switch my phone from LEO1000 to 1024, but idk..i could have sworn my phone in the bootloader read 1024 at some point...
lol this is my first post, sorry if its disorganized and confusing.
if this helps this is what my bootloader reads
LEO1000 SS-B3 (NA)
NSPL0.96.2250.0
MicroP(LED) 0x05
MicroP(TOUCH) NA
SD NONE
Partition Info-v211v413
** i currently have a 4gb sd card in so idk why it says "none" ..i also have the 16gb card it came with i can use in its place if i need to change.
Did you HSPL your phone?
Doesn't seem so.
Ckckckck said:
trying to put this rom on my phone -http://forum.xda-developers.com/showthread.php?t=1080950
but i feel like and idiot bc for some reason my phone says LEO1000 and it says in i cant get that rom without being LEO1024...I dont know very much about roms& spl's but i can follow instructions pretty well. Please help!
Something tells me i cant switch my phone from LEO1000 to 1024, but idk..i could have sworn my phone in the bootloader read 1024 at some point...
lol this is my first post, sorry if its disorganized and confusing.
if this helps this is what my bootloader reads
LEO1000 SS-B3 (NA)
NSPL0.96.2250.0
MicroP(LED) 0x05
MicroP(TOUCH) NA
SD NONE
Partition Info-v211v413
** i currently have a 4gb sd card in so idk why it says "none" ..i also have the 16gb card it came with i can use in its place if i need to change.
Click to expand...
Click to collapse
Yeah looks like you havent installed HSPL Before hand. Your on NSPL0
I have hspl , hspl 2 , 3 & 4 all on my desktop & i currently can use 2 3&4
i have hspl 2.08.HSPL right now on it.
*When i power down my phone (take out the battery). Then hold the power button and volume down button together (and it powers on) it reads this:
PB81120 SS-B3
SPL-2.08.HSPL 8g XE
0x05
CotullaHSPL 0x50
Phone works great, everythings fine, just wanted newer rom thats all.Idk how i changed the "id" of my phone or how to change it back..does flashing different hspl's change your leo #?
nvm i got it to work, just flashed rom from usb flasher from mgldr menu instead of bootloader