I tried to flash HME but remained in odin: setup connbection .... now no longer 'in fashion and I just download icon and from a computer help me please? the tab when I connect is detected by Odin in download mode but it is not what I do?
ok pit jm6 = ok
pit jm6 e ok
Related
Hi,
Last night tried to upgrade the firmware of my Tad but something goes totally wrong.
My device was Vodafone GR fully unlooked with firmware:
PDA: P1000BUJI4
PHONE: P1000BUJI3
CSC: P1000VGRJI1
I have try to back up the firmware using “Roto Backup!” but “adb shell” command not completed.
I pressed with the firmware update without having the backup using this steps:
Download from Famfirmware P1000XXJMA and Odin3 v1.7
Use the included in Odin P1_20100909.pit and in PDA the JMA.tar file using Repartition, Auto reboot and F.Reset time.
Enter the device in Download mode and update without error.
After finishing the update, device rebooted in Download mode again.
Disconnect device from USB and reboot holding the Power bottom.
The devise stack in Samsung logo and vibrate once and then another 3times, this happened in loop.
Try to flash older firmware using Odin3 v1.3 1 with error
<ID:0/015> Firmware update start..
<ID:0/015> boot.bin
<ID:0/015>
<ID:0/015> Complete(Write) operation failed.
Click to expand...
Click to collapse
Try to flash the Vodafone P1000BUJI4 and discover that installing CSC after reset get error E:signature verification failed, Installing Muti-CSC Installtion adorted.
Now Tap be able to boot but not PDA and CSC version appeared only the Phone version appeared P1000XXJM6 (the last tried)
PDA:
PHONE: P1000XXJM6
CSC:
Any Ideas???
Try to flash the JJ4 with P1(which is a full firmware, if you got errors go ahead with the JM6 still without repartition) and then JM6 don't select re-partition when you flash the JM6.
I have install the P1000XXJM6 form http://forum.xda-developers.com/showthread.php?t=854300
Now PDA and CSC appeared correctly.
I steal cannot downgrade.
Also I discover that E:signature verification failed, Installing Muti-CSC Installtion adorted error appeared when I try to install CSC from other version.
Also in JM6 non included Greek input language, is it normal???
Is there any firmware with Greek language input???
Thanks’ in advanced.
dilis said:
I have install the P1000XXJM6 form http://forum.xda-developers.com/showthread.php?t=854300
Now PDA and CSC appeared correctly.
I steal cannot downgrade.
Also I discover that E:signature verification failed, Installing Muti-CSC Installtion adorted error appeared when I try to install CSC from other version.
Also in JM6 non included Greek input language, is it normal???
Is there any firmware with Greek language input???
Thanks’ in advanced.
Click to expand...
Click to collapse
A little bit late, but better than nothing
If you want your tab to have latest Vodafone firmware (gingerbread) follow the instructions below:
----1) download Check Fus Downloader 2.1 from here
----2) use it with the following codes shown below to download latest gingerbread official firmware for your tab:
-------In standard tab, write the following inside the firmware info label:
-------Product code: GT-P1000CWAVGR
-------PDA: P1000BUJMC
-------CSC: P1000VGRJM3
-------Phone: P1000BUJM2
-------Press check firmware. Get it! (download button)
-------Flash it with odin 1.7
-------Done and enjoy your fresh tab!
----3) if you want to root it also, get this attachment CF-Root-TAB7_XX_OXA_JQ1-v3.3-CWM3RFS.zip from this post.
----------- Follow the following instructions to the letter. Do not touch any buttons or checkboxes that are not listed below to touch!
----------- Unzip the attached CF-Root-xxx-vX.X.zip
----------- (USB) Disconnect your phone from your computer
----------- Start ODIN
----------- Click the PDA button, and select CF-Root-xxx-vX.X.tar
----------- Put your phone in download mode
----------- (USB) Connect the phone to your computer
----------- Make sure repartition is NOT checked
----------- Click the START button
----------- Wait for the phone to reboot
----------- Done!
----4) optional, but better to do it: when it reboots, before first start, press volume down and use wipe in every option you see available. look at the advanced submenu also (dalvik cache). Backup important files first, you will lose everything! You have to do this step to erase foreign CSC setting and set it back to VGR!!!
Done! your tab will work like a charm! I hope this helps you!
edit:
I finally managed now to flash DBT NB4 with PIT..
Hello guys,
I have some problems with my N9005.
First problem:
I tried to update my bootloader, also modem witn Odin 3.09
BL: NA6
Modem: NA2
Tried to update bootloader to ND5, also tried modem to NC2. I used key combo to get into download mode.
Auto Reboot and F Reset Time ticked, nothing else. Tried one by one, first BL with BL tab, modem with CP tab
Nothing changed after reboot... still NA6 and NA2
I also used mobile odin, skips modem cuz of write protection. This also is readable in download mode.
Second problem:
After every reboot (normal, recovery, etc.) the time is reset, you have to config manually or let it grab frome time-servers.
Annoying...
Can anyone help me?
Can anyone help me?
I tried to flash N9005XXUENB7_N9005DBTENB2_N9005XXUENB1_HOME.tar.md5 with PDA tab now, with hidden.img it stopped with FAIL (size)
So I used the pit file for DBT and tried again, still FAIL! (Size)
Note 3 now starts only to download mode with firmware upgrade error warning...
edit:
I finally managed now to flash DBT NB4 with PIT..
Sometimes pit file is needed for certain firmware.
http://forum.xda-developers.com/showthread.php?t=2643109
When updating bootloader and modem, u have to shutdown phone completely before the 3 combos. And do it one by one at the correct tab.
Sent from somewhere under the sky, at the corner of this rounded earth.
I was trying To install twrp But Odin sayed 'no Pit partition ' And on The Phone there is The screen 'firmware upgradw encountered An issue . Please select recovery mode in kies. I tried To install Pit file with stock firmware But is The Same. (May i didnt checked debug usb)
Flash a full stock ROM in odin
No Pit partition. And when i flash rom + Pit give me The Same error
The Samsung Galaxy S5 (SM-G900F) is stuck at the boot screen and keeps restarting. I cant go into recovery mode. I can only go into the download mode. I tried to flash it with odin and update it with kies. But none of it works.
At the download mode screen it says:
ODIN : flash read failure
Error: There is no pit binary
Odin screen:
<ID:0/013> Odin engine v(ID:3.1101)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013>
<ID:0/013> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help will be appreciated
Got your back.
Hey man just make sure you closed odin completely.
1. Start Kies
2.Click Tools-> Firmware upgrade and initilazation
3.Type in model of your phone for example sm-g900i which is my Australian S5 then it will ask you for your SN which is a 16 digit code serial number located on the back of your phone when you remove the battery.
Then just follow steps until it asks YOUR phone to be connected... DONT connect it yet...first put it in download mode; phone turned off; press home but, power but, and vol down bot at same time then press vol up key to enter download mode.
Connect phone; then just wait 1 hour and voila you got your phome with latest stock firmware.
Please reply to us if this worked for you as this can help new users to determine what to do.
Cheers
Sorry but English is not my first language, hope i made myself clear.
If there is anything else i can do to assist please let me know.:laugh:
Which Kies works with the S5? Because neither seem to be working
I'm having pretty much the same problem, had a bad flash and can't boot into recovery or get it detected in Kies
And I can't flash stock Marshmallow or Lollipop till I finish downloading them
Going through firmware upgrade and installation option and putting in the model just causes Kies to freeze using either version
WalkableBuffalo said:
Which Kies works with the S5? Because neither seem to be working
I'm having pretty much the same problem, had a bad flash and can't boot into recovery or get it detected in Kies
And I can't flash stock Marshmallow or Lollipop till I finish downloading them
Going through firmware upgrade and installation option and putting in the model just causes Kies to freeze using either version
Click to expand...
Click to collapse
Kies will automaticlly download the correct atock fw.....just use Kies lite versiom which is the one i used a couple of days ago and had exactly the same problem as you i actually had a corrupter pit file so there was no partition being found...again install and use lite kies for samsung then just dlow the steps ut should automatically download the firmware and install it into samsung at the same time you shpuld not remove the cable whatsoever during download and installation and actually make sure yu have the drivers for samsung installed and that the usb cable you are using is original....hope it works if you need a detailed guide with instalation steps let me know or heck i cpuld even help out with a video just let me know.
Hope you get it sorted and if you do please let us all know so in the furute people can see the answer.
Cheers.
It's alright I fixed it now, still couldn't get Kies to work
I flashed the latest version of Lollipop (no carrier) to the phone, which initially sent it into a bootloop. But that enabled recovery again so I did a data and cache wipe, flashed the same ROM from ODIN again and it worked
Hi all, i've also posted this on sammobile but have had little response. I installed TWRP on my S8 (G950f) and when it rebooted got stuck on the logo screen. I cannot enter recovery mode, only download mode. I've tried flashing with the latest Odin and it fails at the start with error DeviceInfo. So i installed an older version of Odin and now receive the error 'Set PIT file'. I cannot find a PIT file online for the G950f and upon reading it seems this is taken from the CSC file when 'repartition' is selected. I've done this to no avail, still 'Set PIT File' is displayed. I'm certain that the firmware is correct as it's been used before with success. For some reason this TWRP seems to have effed things up. I'm close to putting the phone on Ebay and never touching samsung again
This is my Odin log:
ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005>
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
This is my Downloading Page text:
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G950F
CURRENT BINARY: CUSTOM
SYSTEM STATUS: Official
FRP LOCK: OFF
OEM LOCK: OFF
Secure Download: Enabled
CCIC = S2MM005 hw: 6 boot: 7 main:3C
WARRANTY VOID: 1 (0x030c)
RP SWREV: B:1 K:1 S:1
DID = 02b50c50a9c2
EVT 1.1
LOT_ID = NBV6P
CHIP_ID = 02b50c50a9c2
nASV_Table_Version: 8
nASV_Group_CPUCL0: 9
nASV_Group_CPUCL1: 8
nASV_Group_G30: 3
nASV_Group_MIF: 9
nASV_Group_INT: 9
nASV_Group_CAM_DISP: 9
nASV_Group_CP: 9
nASV_Group_PMIC: 0
nASV_Group_PMIC_CP: 0
PMIC_ID = 2(e4)
LPDDR4 manufacturer = Samsung
LPDDR4 process ver = D18
LPDDR4 size = 4gb
Have you tried https://forum.xda-developers.com/galaxy-s8/help/stuck-bootloop-flashing-aqg5-fix-t3636857 ?
Hi, i've downloaded the file mentioned but it's a zip file and there's no BL file contained within it. I can't install via recovery as my phone wont enter recovery.
holidayaddict1 said:
Hi, i've downloaded the file mentioned but it's a zip file and there's no BL file contained within it. I can't install via recovery as my phone wont enter recovery.
Click to expand...
Click to collapse
Download the BL from https://www.sammobile.com/devices/ or using https://forum.xda-developers.com/galaxy-tab-s/general/tool-samfirm-samsung-firmware-t2988647
OK I've gotten somewhere (i hope). Followed your suggestion and after repeatedly pressing the Start button in ODIN have managed (somehow) to get into TWRP. However when i click 'install' the 'internal memory' displays as 0 with no option to select it.
Where do i go from here? Looks as if the internal storage is corrupt
The pit file is located in the CSC_OXM_G950FOXM1... file. Open it with winrar or 7zip and extract it.
Sjant said:
The pit file is located in the CSC_OXM_G950FOXM1... file. Open it with winrar or 7zip and extract it.
Click to expand...
Click to collapse
Do i need to exit TWRP then? I feel like i'd gotten somewhere
holidayaddict1 said:
Do i need to exit TWRP then? I feel like i'd gotten somewhere
Click to expand...
Click to collapse
Yes, you need to use Odin, or alternatively Smart Switch.
Sjant said:
Yes, you need to use Odin, or alternatively Smart Switch.
Click to expand...
Click to collapse
I've (kinda) managed to sort it!
Looked online and downloaded the files for AQF7 (just the BL and CP files) and whilst in download mode clicked start, held the 3 download buttons down again and hammered the start button in odin.. that made it boot into TWRP. However this just proved there was no partition there as the internal memory read zero.
So i downloaded the firmware for my device (XEU) and opened the CSC file with 7-zip and took out the .PIT file then in ODIN I JUST added the .PIT file and BL files. Pressed start and it worked but still only booted to the logo screen.
Next i added the AP file in ODIN and flashed that. This now went without a problem as the .PIT file had done its job repartitioning the phone.. The phone then restarted and booted to the welcome screen.
Some oddities which i don't understand are that in my Settings menu i now have an option 'T roaming' which shouldn't be there. and also a service provider option for 'KT twophone' whoever that is.
Confusing as i selected my countries (UK) XEU firmware.
My phone says 'international' on the boxes label so whether it's different firmware i'm not sure (couldn't find an international firmware on sam mobile).
*Edit..
I discovered that the additional options in the settings menu were due to me not flashing the CSC file so i reflashed all files at once (ensuring that odin had been reset first) and everythings back to normal.
Interestingly i wonder if i flashed a USA CSC file, would it give me access to the additional content available through the samsung USA store - they seem to have more AOD's, addons etc
Well Derr... because i discovered that android pay didn't work i felt like i had no option but to install TWRP... tried it, followed the instructions perfectly and it failed on DeviceInfo so now i'm back to the beginning.. stuck at the galaxy logo screen ( getting fed up of this phone now
holidayaddict1 said:
Well Derr... because i discovered that android pay didn't work i felt like i had no option but to install TWRP... tried it, followed the instructions perfectly and it failed on DeviceInfo so now i'm back to the beginning.. stuck at the galaxy logo screen ( getting fed up of this phone now
Click to expand...
Click to collapse
It got worse, however i've fixed it. I kept getting stuck in a boot loop despite having a successful flash. I just happened to check the files being flashed and realised that the BL file was the AQF7 bootloader and the other files were from my countries firmware. so i reflashed just the BL file for my country and the phone has now started
It looks as though flashing with TWRP won't work on my device for some reason as it seems to delete or corrupt the PIT. It's then a pain to get it all back working again.
Any other options to install TWRP?
Thanks
holidayaddict1 said:
I've (kinda) managed to sort it!
Looked online and downloaded the files for AQF7 (just the BL and CP files) and whilst in download mode clicked start, held the 3 download buttons down again and hammered the start button in odin.. that made it boot into TWRP. However this just proved there was no partition there as the internal memory read zero.
So i downloaded the firmware for my device (XEU) and opened the CSC file with 7-zip and took out the .PIT file then in ODIN I JUST added the .PIT file and BL files. Pressed start and it worked but still only booted to the logo screen.
Next i added the AP file in ODIN and flashed that. This now went without a problem as the .PIT file had done its job repartitioning the phone.. The phone then restarted and booted to the welcome screen.
Some oddities which i don't understand are that in my Settings menu i now have an option 'T roaming' which shouldn't be there. and also a service provider option for 'KT twophone' whoever that is.
Confusing as i selected my countries (UK) XEU firmware.
My phone says 'international' on the boxes label so whether it's different firmware i'm not sure (couldn't find an international firmware on sam mobile).
*Edit..
I discovered that the additional options in the settings menu were due to me not flashing the CSC file so i reflashed all files at once (ensuring that odin had been reset first) and everythings back to normal.
Interestingly i wonder if i flashed a USA CSC file, would it give me access to the additional content available through the samsung USA store - they seem to have more AOD's, addons etc
Click to expand...
Click to collapse
Hey mate. I am in the exact same boat as you, I am new to this and need some help. Where did you get your files, could you link them to me please? I don't know what I am meant to be doing and my back up didn't work properly so I can't even just go back to stock