Database Users

please help!! after ROM upgrade the device stuck completely!

please expert guys help ...
i have new leo with ROM 1.43 today after trying to upgrade to ROM 1.66 I did everything as asked, the installer began , with all the colours on the leo display then it started the percent completion counter , and after 2% it wrote me error something , and the leo restarted but stuck in the white start up menu with the green HTC icon and below the R G D information but the device doesnt proceed further and stuck here !!!
please help !!!!

it write me as i recall
it wrote me if i recall right :
INVALID MODEL ID

did you install HSPL before trying to install the ROM?

no i didnt try to install anything !
no i didnt try to install anything ! , just started the intallation file ROM arabic-english , and did what i asked to do !

if i didnt install hspl what can i do ?
can i take the device to the shop i bought it from and use the warranty ?

well, no...did you get the file from HTC direct or off here? your phone could be vendor locked to your provider so if you can get the original ROM that was on your phone you can flash that back on...
you should really read into things before jumping in at the deep end...

well i have an inlocked device ...
o bought the device in europe , but i am from israel , htc sent me notification about new arabic ROM with link , i tried with my serial to download but couldnt , it wrote me "this upload not compatible with ur device" , i downloaded it from here XDA developers , but it went wrong !! , the problem that the phone stuck in the loader menu , before uploading the sense interface , and i have no connection between the pc and the phone "no active sync" so how can i reinstall the older version or make the phone load again ?!!?!! plz help !

you need the original ROM and a connection to your PC. run activesync as even not working it should connect up...

no there is no connection the device centre says not connected
the phone is not responding and the pc doesnot establish connection with it , i am stuck with loading menu with the R 2.04.50.22~2
G 15.26.50.070
D 1.43.7024
from there nothing moving , if i do soft reset it , it stucks again in the same menu !!!
i didnt install HSPL , and i guess i tried to install not the correct region ROM upgrade , the phone was purshased in lithuania , but htc offerd me middle eastern ROM because i want the arabic - hebrew support !
plz help

You could try installing the Shipped ROM via microsd card method. Just make sure your battery is above 50%. then follow these steps:
1. Using 7Zip, Open your Shipped ROM.exe (You need your exact shipped ROM for this, anything else will give you the error you got)
2. Look for the "RUU_signed.nbh" (without the quotes)
3. Copy RUU_signed.nbh to your microsd card AFTER formatting the microsd as FAT32 (quick format works well enough, using Win 7)
4. Rename 'RUU_signed.nbh" to "LEOIMG.nbh" (again, without the quotes)
5. Take out the HD2 Battery and insert microsd card in slot.
6. Put Battery Back on and hold the "Vol Down" key while pressing the Power key
7. Follow the instructions on the screen... (remember you need at least 50% battery power just to make sure everything goes as planned)
8. Soft Reset after your done and you have a "Fresh" Shipped ROM on your HD2!
Optional:
9. Install HSPL (use the guide that's been stickied in the ROM Dev Section)
10.Flash the ROM of your choice via MicroSD method or activesync (again, please read the Stickied guides in the ROM Dev Section)
Good Luck!

total storage 328 instead of 180 !!!
well i didnt need anything to do, i pressed and hold the up vol. and down volume and pressed the power key , it did a hardreset and my old ROM back to me , though i noticed strange thing !!!
after the hardreset back to my old ROM i checked the SD card & phone storage and i found that i have now total storage 328 instead of 180 !!!
but then i upgraded my ROM this time with legal one from HTC support site , and the total storage got back to 180 again !!!
anybody knows what happened here ?!
p.s thank u guys for the help

Htc hd2 brick =(

Hello people ...
not much to say ...
i think i bricked my phone .... =(
i installed one of the ROM downloaded from here ...
and it brick my device ...
what should i do ? :`(
it says on the screen :
" Your OS ROM isn't customized for you hardware.
Please refresh the proper ROM code or contact the service center. " ((
p.s. i cant install other ROM
couse it cant see the usb (((

i got the problem solved =)
guess it came from it self couse i was nurvios )))
i entered the hard boot menu pressed the UP (volume) button and then pressed 2 time i think the up(coluve) and down(volume) then it not entered the boot option but connected the USB ...
i installed other ROM and its working fine again ... )))))

so far I have seen 1000 people on xda developers that assume to have bricked their phone...and probably 1 out of 1000 has truly done something stupid to brick his phone.

[email protected] said:
so far I have seen 1000 people on xda developers that assume to have bricked their phone...and probably 1 out of 1000 has truly done something stupid to brick his phone.
Click to expand...
Click to collapse
And then there are the 999 who think they have done something clever, but still bricked their phone...

gladly im not one othe 1\1000 people that done it =)
i had my luck on this one =)

i guess i was celebrated too early...
i tryed to delete the HSPL
by the video tut ... ( yeh yeh ... what can be more easier )
well ...
it says to get a stock rom ( i did it )
it say to put it on the SD after formating it to 32 bit ( i did it )
then hard boot ... ( i did it )
power button ...
and ........... puff ...
now i get: ( On boot ):
PB81100 HX-BC
SPL-1.42.0000 XE
microP(LED) 0x05
microP(TOUCH) 0x03
Upgrage ROM code error
Please try again ...
WHAT IS THAT ? :`(
dose it means i brick it ?
(p.s.)
Tryed to install the HSPL again ...
the install is successfull. ... but no change on the device ...

you have used the wrong rom.
you must use the correct rom that was on the phone when you got it.

Or the correct region. In doubt, just enter your phone's serial number on the HTC download page (here for 1.66) to make sure you get the correct official rom.
Then extract it, put the nbh on your card, etc.

" Sorry, this software download is not suitable for your device. "
hhmm .... i had the hong kong rom originaly ...
maybe it means i have to download it from an hong kong htc site ?

yes....choose the hk site

Are you solved the problem?
How?
I have a similar problem.
I have the same screen at boot, but when I try load anything my device as stuck in progress bar (0%) even for shipped rom’s…
This happens when I try load a shipped rom from SD. Before that I have loaded several cocked rom’s from SD without problem.

the fix...
hold volume up and down together and insert the USB cable then run a different or a good ROM

Bricked friends hd2!!!?!?
PLEASE HELP... I was trying to install android throught NAND on my friends hd2,, in the process of flashing the ROM via Magdalr or whatever.. it froze so i pulled the battery.... and it doesn't turn on. I've pulled the battery on my other friends HD2 so im confused as to why this one in particular does not turn on! PLEASE HELP!!! SHE'LL KILL ME IF SHE FINDS OUT!!!
EDIT: PHEW i figured it out... but im having trouble installing these ROMs

Did i brick my phone??
So my brother was trying to do who knows what to my hd2 and now the hd2 powers on and it says "stick together" (its a t-mobile hd2) and it just stays on that screen.. I'm not the most tech savvy person so bare with me... usually below where it says "stick together" it would show a bunch of numbers and codes and after a few seconds it would load windows mobile and the phone would work fine. However, mine just stays on the stick together and theres no more of those numbers and codes on the bottom.
Did he just brick my phone? And if he did... HOW THE HECK DO I FIX THIS???
HELP :*( i need to use my phone!!
Thanks

Heh I'm in the process of doing my very first flash to get a full install of Andriod 2.2 on my HD2, once I find out a specific answer I've been looking for I'm gonna start the process

HD2 brick
I just bricked my HD2 (USA T-Mous). I tryied update RADIO when was progress on PC 100% in PDA 96% and freezed. I just pulled battery and phone is bricked. When I connect to PC via USB, i can listen twice short plug sound and this is all. No bootloader, nothing. Any reason? Thanks

Did you try to turn on your mobile pushing "vol down" to load usb mode ?
After that, you can flash an official rom.
That "saves" my Leo...

NarkotiQUE said:
I tryied update RADIO
Click to expand...
Click to collapse
if the radio had 51 in the version (example 2.07.51.xx) then it is a brick, dead, gone.

NarkotiQUE said:
I just bricked my HD2 (USA T-Mous). I tryied update RADIO when was progress on PC 100% in PDA 96% and freezed. I just pulled battery and phone is bricked. When I connect to PC via USB, i can listen twice short plug sound and this is all. No bootloader, nothing. Any reason? Thanks
Click to expand...
Click to collapse
Did you have any luck? Does your device have HSPL? Let me know if you still need assistance.

xtntx said:
Hello people ...
not much to say ...
i think i bricked my phone .... =(
i installed one of the ROM downloaded from here ...
and it brick my device ...
what should i do ? :`(
it says on the screen :
" Your OS ROM isn't customized for you hardware.
Please refresh the proper ROM code or contact the service center. " ((
p.s. i cant install other ROM
couse it cant see the usb (((
Click to expand...
Click to collapse
hi i'm looking for a motherboard htc hd2 bricked? can you sell yours?

Htc hero.....bricked :-(help!!!!

Please help me,i've bricked my life(htc hero cdma)i have searched n searched online 4 2weeks for solutions but i have not found not 1 thing to help me,i accidentally flashed a gsm on my cdma & i cannot boot it @ aw,no led lights but yet it charges,i can only hold vol up & tap power while plugged in to wall or pc & it juz vibrates 3x & i need some kinda of solution,anybody!please......:confu sed:

wonderouzdj said:
Please help me,i've bricked my life(htc hero cdma)i have searched n searched online 4 2weeks for solutions but i have not found not 1 thing to help me,i accidentally flashed a gsm on my cdma & i cannot boot it @ aw,no led lights but yet it charges,i can only hold vol up & tap power while plugged in to wall or pc & it juz vibrates 3x & i need some kinda of solution,anybody!please......:confu sed:
Click to expand...
Click to collapse
Hey don't cry!
Here have a hug...
Try this:
g0mib0y said:
EDIT: DON'T UPDATE TO 2.1 AGAIN SINCE IT WILL HANG ONE MORE TIME. WAIT FOR HTC TO RESOLVE THIS ISSUE!!!!!!
EDIT 2: BACK UPP ALL YOUR DATA FROM YOUR MEMORY CARD FIRST!!!
EDIT 3: How did I find this out? I talked to a very helpful HTC suport rep (yes they do actually exist in Sweden). He helped me do these steps and so I thought I should share this.
Ok so you got a message that 2.1 was available for your Hero - FINELY! and you installed it using OTA. And then you got a triangle with a ! in it and you rebooted and all it says is "HERO".
This is how to solve it!
Take out your memory card. FORMAT TO <span style="font-weight:bold;">FAT32</span>!!!
Download the RUU 2.73.405.5 from HTC support homepage
Run the installation.
When it fails to find your phone <span style="font-weight:bold;">DON'T EXIT!!!</span>
If you are using Windows 7 go in to c:\Users\<span style="font-style:italic;">yourusername</span>\AppData\Local\Temp
Search for ROM.zip
Move to desktop
Rename to HEROIMG.zip
Transfer to your newly formated memory card now with FAT32 file system
Put memory card into phone
Start phone holding volume down pressed.
It will now check zip fil and then ask if you want to install.
homekey for YES
After installing you have 1.5 again and can safely upgrade to 2.1 OTA
Click to expand...
Click to collapse
Source:
http://forum.xda-developers.com/showthread.php?t=714519

None of the above applies to the OP since he flashed a GSM radio on a CDMA Hero.
Sorry to say, but you've got an actual brick...

so itz not 1 thing i can do @ aw????

thats not what happend! i described everything!!

[Q] Help on fixing hd2 that wont boot up

Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .

If it doesn't install, and nothing installs, then you need to take it to repair I guess.

I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.

frequency1 said:
I had a feeling about that. I just figured there was no way to fix it and the fact that i couldnt send it back to tmobile to get a replacement was out of the question since the firmware was modified. But your saying there are shops that fix these kinds of issues? If so, I better start looking around over here.
Click to expand...
Click to collapse
why dont you try sd card method for flashing your rom !1! you can pm me if you need further help

Do you mean that it can't get to the boot loader screen (rainbow) or that trying to install a ROM from there didn't work? You might want to flash the original HSPL too, just to check.

What I mean is that everytime I boot up the hd2 it stays stuck on the splash screen. It doesn't even show the rom information in red at the bottom left corner of the screen. But I can boot to the tri color menu though. I have tried to install the tmous official rom by plugging the USB when I'm in the tri color menu and it always stays stuck at 9%. So is there way to fix this or am I screwed.
Sent from my Android Powered HD2 using XDA App

Try the sd-card recovery instead of the USB one.
http://www.jayceooi.com/2011/01/01/how-to-upgrade-htc-hd2-rom-through-sd-card-video/
After that, even if it fails, it shows only SPL in the tri-color screen then you are set to claim warranty.

frequency1 said:
Hey guys I have a hd2 that wont boot up anymore. I have installed several windows 6.5 cooked roms into this device for a while now. Recently this device has been given me a lot of problems until finally it took a dump. Now everytime i power up the device it stays in the splash screen. It doesnt even show radio version, rom version,etc on the bottom left of the screen. So is this hd2 dead or is there some way that i can fix it. I even tried installing tmobile's official rom on this device by going into the "rainbow screen" so that the device can be seen by using the usb cable, but alas....it didnt work either. So any help would be appreciated .
Click to expand...
Click to collapse
Well my bro... i think thats nand problems or heating issues ... does flashing rom goes all ok or it stops during flashing ? if stops than check if you phone is hot - hotter than normal.
Try this : Take out battery, memory card, sim card and put you phone in the fridge for about 5-10 min ( dont worry tried many times... no harm ) meanwhile prepare your sd card to flash rom with sd card method ... to do that extract Ruu rom - stock one - download with hd2 serial nr ( winrar, 7zip etc) find Ruu_Signed.nbh rename it to LEOIMG.nbh than copy to sd card ( format you sd card fat32 and make sure it works ... 2gb will work ) take phone out from fridge put sd card & battery into phone power one phone while holding volume down key ( go into tricolor screen - bootloader) and follow procedure in phone... i hope everything goes well and you fix you phone... but if still no success than flash android or wp7 ( if you have warranty flash stock SPL and return phone).
best regards from me

my htc hd2 is STUCK.. HELP ME PLS

I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help

Before we start, you can ask him how his device has ended up like this, can't you?
boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
Click to expand...
Click to collapse
Sir, you have forgotten your caps locked.
boxboy said:
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
Click to expand...
Click to collapse
Because you have stock SPL, you won't be able to install any custom ROM or any stock ROM not made for your region/SN.
boxboy said:
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
Click to expand...
Click to collapse
AFAIK, task29 is, also to be considered, a custom rom so it needs HSPL to be flashed. Are you sure you have followed the steps correctly?
boxboy said:
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
Click to expand...
Click to collapse
That is not a ROM, it's a radio. You need to flash HSPL to be able to change the splash screen (NRG Screen). HSPL should go like this: SPL 2.08.HSPL .
boxboy said:
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Microsoft is a corporation, Windows Phone is the OS .
One more thing, to be able to flash a LEOIMG from sd, the .nbh must be a rom that is compatible with your device (It will work if you get it from htc.com using the device's serial number)
I hope this helps. And I'm sorry if I am incorrect at something.
Good luck.
------------------------------------------------------------------------------------------------------------------------------------------------
To summarize it, you need to do either one of the following:
1- Install HSPL, and do what you want.
2- Go to HTC.com, download a rom using your Serial Number, rename file to .zip, extract the .nbh file, rename to LEOIMG.NBH [Capital letters], put onto sd card and insert into phone, boot up device while holding volume down ONLY, and make sure splash is removed and you're back to the "htc" stock, then send to repair [why?].

posting teh same post in multiple sub forums is considered rude
http://forum.xda-developers.com/showthread.php?t=1440265

Yeah, HSPL is needed for flashing pretty much everything. One thing you could do would be to flash a stock ROM from your SD card (just google it I CBA to provide links and stuff) which would reset everything to factory WinMo (including SPL to SPL3.03 [assuming you flash the latest ROM 3.14]) and from here it would basically be a fresh start. Probably the safest route without HSPL

Hi.
Thank you for your replies...
Let me tell u guys if I forgot to say earlier. The mobile phone is not letting flash any of the Hspl... be q series, 2 series or 3.series... all the times it says error 0000006 and 000000010 etc... a couple out of hundreds it did let flash but then it doesn't let me flash the factory rom fom HTC.

I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck

OK,
My final.outcome.
This phone let's me flash the hspl but it doesn't let me flush any roms including the original HTC factory rom.
I can also perform the task 29. Etc but still the NRG screen is still there.
I would like to know that if I flash the original Split and send it HTC, will be repairable for free? Sure? Even with the NRG.

now i think the only option available to you is jtagging the device which may permanently void the warranty !!
it had happened with me once, but somehow it got solved !
i used to randomly install clk, magldr, radios, hspl etc multiple times !
it used to get stuck while installing and then i used to remove the battery and try again !!
somehow it started ! !!
STRANGE DEVICE !!

Yeap its a real problem!!
Now , It will not let me change the hspl to spl whatsoever I do.
I would like your suggestions
I bought this brick for £50 and I can return it to get my money back. Has any used jtagging and does it 100% work?. The thing is if I do used jtagging, and if it doesn't work ,then I can,t return it!. How much does it cost and is it worth it?

jtagging will solve your problem !!
they remove the motherboard of the device and flash the os into the motherboard directly through a device named riff box !!
refer this video for more info !!
http://www.youtube.com/watch?v=zElsUERTzOU
but pls do not try this at home ! !!
just contact a local repair shop to jtag your device !!
also u can contact these guys from the video !!
good luck ! !!

boxboy said:
I have succesfuly flashed the 3.03 hspl... bit still no success in flashing any roms ... it gets stuck sometimes at 99% and sometimes at 0% and sometimes it comes up with a scrambled screen and stuck
Click to expand...
Click to collapse
Check that the micro USB connection isn't "wobbly".
I had a TMOUS HD2 and never had any issues. Then, I sold it and got a Telstra HD2 and had big issues getting ROMs installed until I realized that the connection at the phone was a little weak. I can't send any updates to WP7 via cab sender unless the phone is in a certain position to keep the connection from breaking.

boxboy said:
I bought an HTC HD2 FEW WEEKS BACK FROM ONE OF MY FRIEND.
I DO NOT HAVE THE HISTORY OF WHAT HE TRIED TO DO WITH IT.
BUT BECAUSE IT WAS STUCK/DEAD , HE GAVE TO ME FOR CHEAP.
NOW THIS PHONE IS UNDER WARRANTY TILL AUG-2012 AND IS FROM VODAFONE.
(EVEN AFTER INSTALLING ANDROID IT IS VOID)
HE MUST HAVE TRIED SEVERAL ROM/HSPL TO GET TO THIS POINT.
PROBLEM:
When I power up the phone, it displays a NRG LOGO SCREEN (energize software), and it gets stuck on it forever.
When I do hold the volume down + power button, then it comes up with the three colour screen and it says SPL-2.08.0000, AND also says rom update failed (only if i try to install and then start up)
The phone does connect through USB when it is on the three colour screen, but it does not let me install ANY OF THE romS or the spl'S...
I have tried literally every single step possible. I have tried to do task 29, i have tried install the original rom, i have tried to put the rom in the sd card and try it that way.. I have also tried to do hard reset... vol up and down and it does not complete either..
I best rom it let me install was 99% of 2.10.50.19.2.. but after 99% it got stuck .. it seems like it gets stuck within 1 min or so.. anything you do!
Some times after several hundred attempts, it does let me change the spl... as it was displaying 3.... before then i changed to 1.4..... and then to 2.08...
All i want to do is to get rid of the NRG SCREEN, so i could send to the htc ,, for repair ( i know that it is not under warranty if i used andriod, but they will not know) .. or is there any way to completely format the phone,,, is there any solution to install andriod or microsoft? pls help
Click to expand...
Click to collapse
Don't worry ... you can give the life to your phone back... it shows fail bcus u have 2.08.0000.. so it means u Sud have 2.08 v hspl.. so try flashing hspl by getting into bootloader(3 colour) by pressing volume down + power Then flash hspl.. but remember select 2.08v.. then again after flashing hold volume down + power.. bootlooder.. then flash magdlr 1.13 ... now the phone will boot into a black screen with written mangdlr.. wen the black screen magdlr screen comes then press power off for 5mintzz.. follow the guide to flash.. there is a stick thread in NAND DEVELOP... U can get the windows version back to your phone to get the warranty...
Sent from my HTC HD2 using Tapatalk

Ok ,, some good new at last ..
I have used the HSPL4 to change my 3.03hspl to 3.030000 spl...
Success, as when i go to the tri colour screen it says spl and no hint of hspl...
Bad news, is that i still cant get the rom flashing,, as it gets stuff at some point and mostly at 99%.. Have tried both ways through SD (leoimg) and through USB.
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.

boxboy said:
Now final question is ... When i on the phone a big logo of NRG (ENERGIZE) writtten comes up and it gets stuck there.. the phone has SPL .. so it still under warranty to return it?.. I still have all the void sticker intact.
Click to expand...
Click to collapse
did you try to flash just a splashscreen as i suggested in your other thread? (they can be flashed alone, no need for a whole rom, , just like radios)
if you can get a stock splashscreen on there you are sorted.

Maybe try to download the original Software from HTC.
With you serial number you can get the latest windows for this phone.
Flash the Software you get from HTC.
If this is working ok you can try to install any Android ROM.
Read at first this
http://forum.xda-developers.com/showthread.php?t=905841
Try to understand and follow the steps..
But if you have even no luck with original Windows soft. You will also (maybe) have a lot of probs. with Android..

Thank you guys for all your help..
I have flashed andriod on several phones some time ago and I actually forgot the right steps to follow.
But this phone is unique is not letting me finish.
After following all the right steps, i wasnt able to install a rom succesfully even after installing the HSPL... and I am also not able to install the factory rom from htc on either the hspl or spl settings.
But i now got rid of the NRG screen and I have also installed the spl 3.03.. When you on the phone, it displays software upgrade failed..
So I have now sent the mobile to HTC as it is under warranty. I will then re-flash andriod following the right steps and see what happens!
Thanks again!

My mobile came back from HTC with a week.. Looks like a brand new one!
In the letter it says the replaced IMEI, PCBA, FL BD, W/O_ REGIONAL_ID, LEO
WOW
GREAT PHONE... ITS MUCH FASTER THAN THE PREVIOUS ONE FOR SOME REASONS