HELP desire z screen wont turn on - G2 and Desire Z General

Hi everyone, I got my desireZ back in November and it has been working perfect ever since, i have it rooted using VISIONary and everything was perfect until today. The phone was in my pocket and i was lsning to music, i looked at my phone and all i saw was a white line going from the top of the screen to the bottom, i pressed the power button to turn of the screen, then i pressed it again and now all I see is a black screen with the back light on.
I have tried to soft reset the phone, took out the battery sim card and left the phone for a while, came back turned it on and still the same thing black screen with the back light on... The touch screen works fine i still hear the phone receiving txt msges and emails, i can even receive phone calls, and answer them by sliding my finger across the screen like usual.
I am trying to do a hard reset of the phone but i can't do that cause even when i turn on the phone while holding the volume down key i still dont see anything on the screen
any help would be appreciated.
EDIT - after trying to open the keyboard a couple of times, now the screen turns on white... when i press the power button to turn of the screen and turn it back i see a fading effect where the screen slowly turn on from left to right (fades from black to white) and then stays white till i press the power button again....

Since i have rooted my phone, i dont belive i can take it to bell to fix it the way it is... and since i can't see the screen to perform a hard reset to remove the root (i dont have s-off) ... does anyone know of another method for doing this? maybe with connecting to a computer?

awsrasool said:
Since i have rooted my phone, i dont belive i can take it to bell to fix it the way it is... and since i can't see the screen to perform a hard reset to remove the root (i dont have s-off) ... does anyone know of another method for doing this? maybe with connecting to a computer?
Click to expand...
Click to collapse
There is another thread on the forums about someone having the same issue. I believe there is a solution using adb on your PC to connect to the phone.
Not sure how 'tight' your service provider is, but if the screen is dead, and you are still under your warranty period, they may simply swap the device for you after doing some 'basic' tests and dump it into the bucket that goes back to the factory for refurb. The fact that it is rooted won't be discovered until much later, if ever, so it may not be an issue.
Good luck!

gbarayah said:
There is another thread on the forums about someone having the same issue. I believe there is a solution using adb on your PC to connect to the phone.
Click to expand...
Click to collapse
Any idea on the location of this thread, can't find it anywhere.
I am suffering the exact symptoms as the OP with my Desire Z which is rooted with visionary rom flashed - I would really like to know how to use adb to resolve this !
Cheers,
Ste

http://forum.xda-developers.com/showthread.php?t=898486&highlight=blank+screen
http://forum.xda-developers.com/showthread.php?t=864948&highlight=blank+screen
http://forum.xda-developers.com/showthread.php?t=843578&highlight=blank+screen
http://forum.xda-developers.com/showthread.php?t=844795&highlight=blank+screen
http://forum.xda-developers.com/showthread.php?t=821229&highlight=blank+screen
..... Aint read none of em myself,.... Good luck. If you find some to be of use, report back for the others. Peace

Cheers mate, will have a good look tonight

Related

Some Help... Phone blank screening to a degree

Thanks for reading.
I'm currently using WM6.1 on the phone, and loving everything about it.
Since day 1, I've used a phone lock code, along with PIN1 code.
When unlocking the phone for after say an hours inactivity, the keypad will show, then the screen will go blank only showing the top bar of the phone.
Any press of buttons and screen will just make a beeping sound, and so far nothing I've done will restore the keypad to unlock the phone.
Is there anything wrong with the ROM i have, and is there anyone who can suggest how to correct this?
Please remember, the top bar still shows, and a reset allows the phone to work as normal (once logging back into it of course).
Thank you,
Hi guys,
Sorry to bring this back up, but this problem is still going on.
Not sure how to resolve it, so hoping someone would know how to solve this.
Thanks,
Posted twice for some reason.
Maybe is a sw failure,(50%) try to reflash with this fw: RUU_Hermes_CINGULAR_WWE_3625023_6275_1540700_108_UOOS_SVN05_Ship.exe
if your hermes its from att/cingular. after flash open and close the tap of hermes, if the blank screen continues or return this, the failure is hw (the flex component broken,bus, pcb) in this case you need to buy the spare part or send to sat.
good luck
other possible solution
http://forum.xda-developers.com/showthread.php?t=321163
Hi there,
Its not white screening, or anything else, I think the next time it does this, I'm going to have to take a picture, to make sure it can be understood clearly.
Basically, when bringing the phone out of standby (from pressing off/on button) and attempting to enter my pin into the phone the phone will allow me usually to press at least one number of my pin, and then it'll black screen, where the start bar still displays, but no response.
The handset isn't problematic when being opened for use, or anything else, its just annoying to have to reset to load the phone back up again.
I hope this helps?
Further to the above, here is what i've been talking about...
Happened last night, typically as I was bored, and had to wait till morning to take the photo...
Still no movement on this post...
Would it be suggestable to upgrade the install of WM?
If it is, how easy (will read guides beforehand) is it to do (reasonably, hard etc).
Just this is now my only phone, so don't fancy my chances bricking it.
Thanks!
Sorry to be posting yet again, but this has now happened 3 times a in row since last night. I wouldn't mind knowing if a rom fix would sort this, and if so whats the best rom to go for...
Just keen to get this sorted now...
Thanks.
If it helps, I've nothing running when this happens. The exception of last night, where I was using Audio Manager when walking home, and had to soft reset once in the door.
Hi
I am almost certain you have a software fault here and need to reload a new ROM - take your pick - my preference is schnaps - it isnt that hard to do and should solve your problem
Just go to the Windows upgrading section on here and follow the process - you will be happy
John

I think I bricked it...

Before I start I know how touchy people are about searching forums and the wiki etc... but I already have!
Ok so, I tried to flash a new ROM to my phone last night, I have done it before without problems however this time I was having trouble getting the phone to connect to my laptop (I run Windows 7). Both USPL and HSPL wouldn't work (in fact active sync wouldn't even recognise it).
So I went to bed, woke up and... My phone didn't work at all
I spent ages trying to get it too work, I tried putting it into bootloader, but nothing happened, I tried getting it to Hard reset, but nothing happened. (By nothing happens i mean the screen doesn't turn on).
The only sign of life i get from it is the little vibration that usually occurs after the 'smart mobility' screen appears. Except this is delayed by about 10 seconds from after pressing the Power button.
The delay makes me think that there is something else wrong with the phone other then the screen...
Please help!!
Oh and I am sorry for the essay... I only just realised how long and rambling it is haaa.
UPDATE: right it just connected to activesync but still nothing on the screen, is there any way of checking for definite that the screen is broke before I fork out for a new one? There is astill the massive delay between turning the phone on and getting the little vibration...
Try removing battery overnight, then re-inserting. Then try to get to bootloader or hard reset
how exactly did you manage to brick it? did you flash the rom in question with uspl, or do u generally have hard spl installed? i dont know but it looks like the bootloader is somehow broken ...
Ok I will try doing that, thank you for helping
And no, I didnt get as far as flashing the ROM because active sync never recognised the phone in Bootlaoder. I usually use USPL.
Did you fix it? and if so how?
I have very similar issues with my HD right now. Screen went black, bought a new LCD and still the same problem. Oddly enough the only way I can get the screen to come on is to take the battery out and set both battery and phone body in my window sill for half an hour or so. It is cold here right now and they are both pretty cool to the touch when I take them out. Put it back together and tada! Screen comes on. I dunno what the deal is also, don't know if its the battery or phone being cold that makes it work again??? I am going to try and figure it out.. Try it on yours it may help

HD2 frozen on boot

I have just got the HD2 and been using it for a few weeks. Downloaded a few apps (eg HTC rom, BSB tweeks) and all is good. Saw Max Manila and looked like a great idea - checked my manila version 2.5.19211619.0 and downloaded 2.7 SE (checked it's right for my manila) loaded onto phone and it crashed after soft reset. Took battery out and phone doesn't go past first screen (with the red writing bottom left) - Hard reset is the same and now I'm worried!
Any ideas???
sad to say yy sounds like hard reset time.
power off, hold volume up and volume down, tap power keeping volume up and down pressed til the screen comes on and follow the prompts.
it will reset your phone to factory defaults.
never used max manila so I cant help with what the problem might be, but if there is a developers thread for it you might be better asking there.
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
if your phone is provider locked then that will not work.you need the rom that came on your phone. so if was from uk o2 then you need the o2 uk rom, otherwise it wont work.
No luck! Whilst I've got everything to sort the phone out it won't do anything but load the white first screen no matter which buttons I hold down.
Man this sucks!
Guess there's nothing for it except the bin unless anyone else has any other ideas??
can you get into boot loader?
press and hold vol down(not up this time, just down) tap and release power, keep vol down held. should boot to striped cultures colored screen.
if you can what does it say next to SPL?
Hi Samsamual
Thanks for helping but no, won't go into bootloader either - doesn't respond to any input (even when I conect the usb the charge led doesn't come on!) and just starts with the white screen with the HTC logo and then the red writting appears and it just hangs - left it for 5 mins just to be sure and no change
Looks like I've really messed it up although I have no idea what I did wrong - instal went just like the other things I installed.
Ahh shame. All i can suggest is the original rom sd card method. But it MUST be the propper rom that came on your phone, so if you got it from vodaphone, , , even if it is unlocked, you must use the voda rom.
Also, have a really good read through the pages in teh rom development section. If you can find someone with the exact same issue, you could be one step closer to fixing it.
Brotherskid said:
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
Click to expand...
Click to collapse
you must tab the power botton for a short time just tab it and leave it with keeping pressing on the volume up and down buttons don't leave them i think it must work with you tell me if it works
Brotherskid said:
...I'm going to try booting from the sd card b
Click to expand...
Click to collapse
When you tried the SD card method did you use a 2GB SD card and was it formatted to FAT32?
WB
Have you tried a boot (all combinations!) without the sd card installed?
Hoss and WB - thanks for the comments
Hoss, I've held the volume buttons for over a minute after powering on - no change
WB, I can't get the phone to go into boot loader screen but thanks for the info for the future. Next time I'll see if I can copy the original rom just in case.
Resigned myself to having a new paper weight on my desk and looking for a new phone - Guess I won't be putting so many programs on my new one....
PA - Thanks for the advice - Yes tried with sd card in/out sim in/out bootloader, hard reset, soft reset and always the same.
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
rlydiard said:
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
Click to expand...
Click to collapse
What's most annoying is it wasn't as if I was doing anything crazy! Max manila is used by many people (from what I've seen in the threads) and I guess I downloaded the wrong one (although naturally I checked and it's the right one). Certainly will curb my using of 3rd party software! As for the warranty, you're right, I can try and see if it can be fixed (bizarrely, that hadn't occured to me - I thought that with no resets working HTC couldn't do anything). Thanks for the tip and I'll let you know how I get on.
Surely your warranty will cover this. Yes, let me (and us) know how all of this goes. You will get your phone back to what you deserve, for sure!
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
watnuweer said:
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
Click to expand...
Click to collapse
Experential nut I may be, but just wondering if you had the problem after you installed the MAx manila? I wonder now what versions of OS may be causing this problem.
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
fakker said:
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
Click to expand...
Click to collapse
This is getting more interesting, what do you suppose is the cure of taking out the battery, and then charging? I do not doubt your experience, I am just extremely curious if anyone can explain this phenomena.

Argh! The screen is no longer responsive. What to do?

Just as i said - Argh! The screen is no longer responsive. What to do? I can no longer slide the lock across the screen. i have tried to flash the ROM with the 1.66 official but i cannot because it tells me to unlock the phone. I cant! argh! I've pushed the little red button by the battery a couple of times as well as removed the battery. Any suggestions? The hard buttons allow me to answer a call but that's it. i recently turned on the lock for the phone (today in fact) but I've unlocked it several times since doing so before this happened.
Sounds familiar...
Sounds like it is the same problem I had, as well as a few others on this forum. Even after a hard reset, it still didn't work. According to other people here, the solution is to have the screen swopped out for a new one. I've actually just sent mine in today to get it sorted out.
Just curious - I've got a suspicion that environmental conditions may have a role to play in causing the failure. What is the weather in your area like?
Very nice here today. Sunny, mid 50s(f).
I bought this off of ebay. Do i just send it in to HTC?
Try a hard reset, and if it doesn't help then make sure you have an official ROM and send it to HTC.
a hard reset is the little red button next to the battery, correct? ive done that.
and i cant very well change the ROMs at this point now, can i?
lythe123 said:
a hard reset is the little red button next to the battery, correct? ive done that.
and i cant very well change the ROMs at this point now, can i?
Click to expand...
Click to collapse
I would really like to wipe it before i sent it in. i dont want all my info, etc going into someones hands i dont know. anyway to do that?
No, that's a soft reset. Hard reset is pressing the red button while holding both volume keys until you get the "Restore factory settings?" prompt (when the device is on), then following the onsceeen instructions. This is what you're looking for to erase everything, including any possible software bug that could have caused the issue.
If the touchscreen still doesn't work then, send it in.
lythe123 said:
a hard reset is the little red button next to the battery, correct? ive done that.
and i cant very well change the ROMs at this point now, can i?
Click to expand...
Click to collapse
No! A hard reset is:
- Turn phone off
- Press vol up and down at the same time and then press power button (hold vol)
- follow the instructions on the screen
Be aware, that all you data on the phone will get lost. I recommend taking out the SD for that as well. After that u r done. By what you say i assume, that you didnt flash a custom ROM yet, right ?
Thanks! that didnt work either though.
I just want my money back now honestly. This thing, as pretty as it is, is just too much trouble.
Sorry double post...
A faulty device can happen to anybody, just bad luck... can't count how many times it has happened to me as well in the past.
I heard that there is a batch of phones that have a faulty screen, other problems are that without pressing anything the phone still registers clicks, phone doesn't always detect the correct place of where you pressed and the screen not responding.
I have got this on my phone and have arranged a pick up from HTC to pick up my phone for repair, hopefully in a week or two it will come back with a brand new screen that works
Ive had it a couple of months now. Im not sure if i can deal with the lack of apps that my iPhone has, pandora and the like, and the fact that teh HD2 would every so often change time and even date and i cant get weather in places my iPhone can.
In short, i love the HD2 for its specs but i no longer trust it at all.

[Q] Black Screen...

Hello all. First let me state that I rather not make a thread to ask help on a problem that seems to have happened to a few owners, but my knowledge as to how I could resolve the issue is severely lacking..
At some point today my phone was ringing but the screen would not show. I thought about taking the battery out and turning it back on but there would be no HTC, Bootanimation, anything. It was Just a black-lit screen which responds due to tactile feedback and the four touchkeys light up as usual. At first there was an odd sound that would play after a few minutes so I decided to charge it but again there was nothing. Even tried to access bootloader with -Vol and Power still no screen.
I asked a friend of mine to call my phone to see if it would ring but they said it instantly goes to voicemail as if my phone was off. Note that I WAS SURE IT WAS ON.
Adb seems to work with it as it seems whatever I need to do I have to do it through there.
G2 rooted with gfree method
CM7.1 RC1
Clockwork Recovery
Again i am sorry if I bothered those with posting something others would think is "too common of a problem" as I have no experience in fixing this issue. Plus I would like to try any option available as I would not like to try and have my phone replaced (because of the risk of discovering root and obtaining a G2 with stock gingerbread which is currently not rootable)
Please help..
It sounds like you're suffering from some sort of hardware failure. You need to send your phone in for repair/replacement.
The Unnamed Time Lord said:
Hello all. First let me state that I rather not make a thread to ask help on a problem that seems to have happened to a few owners, but my knowledge as to how I could resolve the issue is severely lacking..
At some point today my phone was ringing but the screen would not show. I thought about taking the battery out and turning it back on but there would be no HTC, Bootanimation, anything. It was Just a black-lit screen which responds due to tactile feedback and the four touchkeys light up as usual. At first there was an odd sound that would play after a few minutes so I decided to charge it but again there was nothing. Even tried to access bootloader with -Vol and Power still no screen.
I asked a friend of mine to call my phone to see if it would ring but they said it instantly goes to voicemail as if my phone was off. Note that I WAS SURE IT WAS ON.
Adb seems to work with it as it seems whatever I need to do I have to do it through there.
G2 rooted with gfree method
CM7.1 RC1
Clockwork Recovery
Again i am sorry if I bothered those with posting something others would think is "too common of a problem" as I have no experience in fixing this issue. Plus I would like to try any option available as I would not like to try and have my phone replaced (because of the risk of discovering root and obtaining a G2 with stock gingerbread which is currently not rootable)
Please help..
Click to expand...
Click to collapse
A. They don't care if its rooted.
B. You can root stock Gingerbread.
Same issue here...
I'm facing the same issue, when i try to unlock the phone (power button or trackpad) the screen lights but stays black, and the buttons are also backlit. I have to lock again with power button and unlock again to get to the actual screen.
It first happened a few days ago, and since i didn't reboot/restart in weeks i tried to reboot but the same issue comes back.
then i shut it down, pulled the battery and then back, and restarted: the phone goes directly to that black backlit screen, i tried several times and tried recovery with no luck, so i thought my phone was messed up although i did have some haptic feedback, well in fact the phone was actually booting, but just not showing anything else than the backlit screen; i waited a minute or so to the booting completes (still shows nothing), then i lock/unlock the screen again and there it is, asking for the pin code.
I tried to go to the recovery again to try to wipe dalvik-cache, i know for sure it goes to recovery, but with a totally black screen, not even backlit this time; the trackpad is too sensitive in the recovery to just blindly navigate in the menu, so it is not useable at all.
Then i had the idea to go to Rom Manager, i reflashed the rom from my sd-card, and enabling wipe dalvik-cache, which worked (all through a black screen). After a few minutes i "felt" it rebooting (vibrating) but still back to that black backlit screen, and i locked/unlocked it again and back it was asking pin code...
I also tried to roll back recovery to 3.0.2.4, since i remember i updated it a few weeks ago, but still the same issue.
I don't know what else to do without accessing the recovery, i wanted to try another kernel, or remove the trackpad wake... is there a way to do it via a script? I guess it's what Rom manager does...
Next step will be a total wipe, but i need to make some room on my sdcard for backup purposes first...
If anyone has an idea to sort this out, i'm highly interested...
I'll try to get a logcat, maybe could give a hint
Edit: Virtuous sense 2.0.0 (used it with no issue since it came out, could it be a hw issue?)
Edit2 : attached logcat
Is the pin screen differant than the usual one ie white number keys? If it is that's the sim lock screen you need to call the carrier to get the code or find out the default. Or just get a new sim lol
nah it's the 4 digit pin code, i didn't lose it btw, it's still working and i can use the phone, but i have a black backlit screen whenever i want to wake the phone, and thus when i receive a phone call, i don't know who it is and i blindly press/swipe the screen to answer, because if i want to use the same trick of locking /unlocking, it doesnt work as the lock button is also used to reject a call...
Maybe rip and reinstall the phone app?
asim0 said:
I'm facing the same issue, when i try to unlock the phone (power button or trackpad) the screen lights but stays black, and the buttons are also backlit. I have to lock again with power button and unlock again to get to the actual screen.
It first happened a few days ago, and since i didn't reboot/restart in weeks i tried to reboot but the same issue comes back.
Click to expand...
Click to collapse
I have the same exact problem as this EXCEPT, it's intermittent. Sometimes when I wake the phone I get an all black but backlight screen, and other times it's fine. I'm on CM7.1.
But a superwipe and reflash will probably fix it. Also don't restore system data on TB
I know i still can use wipe data + cache + dalvik through rom manager, and i always used to superwipe before switching roms, but how can i do that now when the recovery is all blacked out?
can anyone guide me to a script or something i could do while the phone is active, to tell him to reboot to recovery and flash that superwipe?
anyway i'll try the regular wipe and keep the thread updated
---------- Post added at 02:42 PM ---------- Previous post was at 02:35 PM ----------
SuperDave81 said:
EXCEPT, it's intermittent.
Click to expand...
Click to collapse
On my side if i leave the phone locked more than 30 seconds, it happens 100% of the time; also I noticed that now the backlight blinks 2 or 3 times (1 second blinking) when locked, first a few minutes after locking, and then randomly, about 3 or 4 times per hour; I guess it's getting worse;
I've read on another thread that it could be video cable getting loose, but since mine is still under guarantee, i won't open it right now just to check, if i can't fix by wiping / superwiping (when i know how to), i'll use that guarantee, which is one month left (lucky me)
EDIT: one other thing that makes me think it's no hardware, when the black screen appears because of a phone call or a message, the ringtone and notification sound are both half as loud as they should be, this is all really strange
after backing up my data, i reflashed the rom via Rom Manager, and I wiped data and cache (which equals to factory reset) this time: the first screen that should show the pin code numpad was already a black (backlit) screen!!
Also, thinking about it, i realised that the "flash rom from sdcard" menu in Rom Manager is in fact "Flash ZIP from sdcard": the zip doesn't have to be a ROM!!
So I tried flashing a new kernel this way, also some framework modifications (extended settings, removed TP wake, etc...) they all install Ok, but still this black screen...
Also I was about to flash SuperWipeG2.zip this way, but if it doesn't fix my problem, I will be stuck with a blacked out recovery, as SuperWipe wipes everything including /system; so if anyone has an idea to tell Rom Manager to flash two zips (Superwipe then Rom) i'll be willing to try, or a script to do that;
Maybe i'll have a look of the scripts in Superwipe and in the rom, and put both zips together... don't know if it's possible?
Maybe I'll try the Superwipe alone if I can get a spare phone, just in case...
Other thing:I used the phone's gps for more than 5 hours with the screen lit, and it never flickered even once; so it's hard to believe it's a screen connection issue...
Just to keep this updated, everything i did, including superwipe didn't change this issue, so i sent it back to the technical support (under guarantee) and I got it back today; the report that came with it says the screen has been replaced; so it was hardware finally...
Hi, i have same problem.. Black screen in recovery and during the boot. When the system boots, screen is OK. Sometimes i have also blackscreen when I want to use HW keyboard. I tried 4ext, reflash older versions of CW but still the same. I can see a screen through Android Screen Monitor and I can cotrol it. But phone is blak, only backlight. Can somebody say, how to solve this issue?
So, for other, if you cant see screen, you can use Android Screen Monitor for Windows and connect phone through USB and see a screen.
G1ForFun said:
A. They don't care if its rooted.
B. You can root stock Gingerbread.
Click to expand...
Click to collapse
WAIT one minute... they don't care? where was I when this meeting took place?
I had this issue as well on a spare G2 I had.
The screen was just black but you could tell it was lit, hardware keys were lit as well.
The phone was actually my brothers and it rooted w/ CM7.
I ended up selling the phone as is on Ebay but after some research it was a failure in the hardware for the screen and I found extensive instructions on how to replace it that I didn't wish to do.
I never attempted to get it replaced and kind of wish I did now if they don't care about the device being rooted.
I purchased my G2 before he had his, and it's never had the issue so not sure what to think of it.
Saintfyre said:
I ended up selling the phone as is on Ebay but after some research it was a failure in the hardware for the screen and I found extensive instructions on how to replace it that I didn't wish to do.
Click to expand...
Click to collapse
I think I have similar issue, can you post where you found those instructions?
Thanks in advance!
http://www.youtube.com/watch?v=u-dR8CHEGjY&feature=youtube_gdata_player
Sent from my HTC Vision using XDA Premium App
I used the same tutorial to change the LCD but after I put the new its just the backlight but nothing else... I will give it another go maybe and have a look again at those ribbon cables! I guess...
---------- Post added at 10:59 AM ---------- Previous post was at 10:09 AM ----------
I found on ebay: HTC-Desire-Z-T-Mobile-G2-A7272-Slide-Flex-Cable-Ribbon
or I found also with the chassis for a bit more.
Thinking to buy this, it would be great if anyone could confirm that it would help "my condition" ?
THanks in advance!
In terms of cables, yes the flex cables are what you want.
Sent from my T-Mobile G2

Categories

Resources