How does one go about doing this without damage the back cover?
thejron said:
How does one go about doing this without damage the back cover?
Click to expand...
Click to collapse
Not to sound like a smart ass, but carefully im sure it can be done but without damaging the rest of the cover, im not so sure.
I think you'd be safer to just put a nice, low-profile black case on it. Or maybe rubberize it with spray-on plastic, that might look nice. I'm having trouble imagining how you'd remove the logos and not cause any damage to the rest of the cover. Some sort of chemical bath or soft scraper, maybe? Or you could try just buffing them out.
I've never done it but I remember people using sugar cubes to do this in the past.
I take no responsibility if you trash your battery cover doing this though.
Related
PLEASE HELP
My wife has this phone..(so do i) well anyway she found a way to do the impossible. she broke her headphone jack in the headphone hole. The tip broke and the bottom is logged in the hole. I tried to get some super glue to perhaps stick it together and pull it out..this did not work. I took the back cover off to get more access but still cant get it..any one have any suggestions...now i also have a lot of superglue residue in the hole. is there any way to open this thing and get the rest of the plug out? BTW it is not the N1 headphone but another brand. PLEASE HELP
Is the tip hollow? If so you could try taking a small screw into it in order to have something to pull it out with.
aj
how deep is the remaining part?
the tip is not hollow and the shaft part is broke off under the plastic part.
ok this is not a joke.....
BUT if you are feeling "ballsy"
take your average sewing needle and heat it up with a lighter stove w/e unitll it is red-hot. USE A PLIERS TO HOLD IT
then plunge it into the center of the remenants and let it cool
only try this if there is some plastic left in there.
lol...I will try that...hope it works, how will the needle grip the broken part of the headphone. would it just pull right out.. I need something to grab or grip the broken part....I dont want to break my phone.
Well the poster with the needle idea has the goal of having the hot needle cool with melted plastic from piece that is broke off. Once cool, the hope is that the plastic will adhere to the needle (now completely cool) and allow you to pull it free.
I have some reservations about this idea. How did she break the tip off. Was it a sideways motion? Or did you try to correctly remove the plug but for some reason it was stuck and the tip was left lodged in?
If it was the later of those, the needle idea will do nothing. It may work is it happened the first way I described.
An alternative to the needle idea and potentially more damaging is to take a paper clip, place a small bead of solder on the tip. Avoid touching any of the phones internals with the solder and press that paper clip up against the broken tip. It should not take long to cool. Once it does, it may give the the force you need to pull it free.
Please report back when you have sorted this out. We are all curious.
maybe a little dab of jbweld or gorilla glue, if worst comes to worse of course. It would be much easier if it were hollow.
What about a really strong magnet?
gIMpSTa said:
What about a really strong magnet?
Click to expand...
Click to collapse
You want to stick a high power magnet next to a 530 dollar phone? Are you nuts?!?
The way to take out a broken screw is to drill a small whole in the center and try to wedge the smallest Allen wrench into it.
Maybe that might give you some sort of idea on how to dislodge that earpiece. I know it's not the same thing...but its N idea.
McFroger3 said:
You want to stick a high power magnet next to a 530 dollar phone? Are you nuts?!?
Click to expand...
Click to collapse
And what exactly do you think would happen?
I'm not talking SUPER magnet, but honestly, what component of the phone do you think is in anyway affected by a magnet?
There is a myth that magnets destroy electronics. Sure you can use a magnet to wipe a hard drive (not flash storage, talking magnetic disk) but it takes a SUPER strong magnet with a concentrated beam to do even that.
gIMpSTa said:
And what exactly do you think would happen?
I'm not talking SUPER magnet, but honestly, what component of the phone do you think is in anyway affected by a magnet?
There is a myth that magnets destroy electronics. Sure you can use a magnet to wipe a hard drive (not flash storage, talking magnetic disk) but it takes a SUPER strong magnet with a concentrated beam to do even that.
Click to expand...
Click to collapse
Magnets will not do anything, Blackberry uses one to turn the screen on/off
did you get it out????
Not yet still trying. .already voided the warrenty
Sorry if there's already a "purple stains on my HD2" but I just ordered this one on ebay and apparently the guy's daughter kept a purple case on it.. this is the result.
I don't wanna screw it up trying to clean it with alcohol but does it look like this could come out? or has anyone else used cases that have caused this?
Just get yourself a nice black case and with time the purple might wear down. I would much rather do that than ruin the rubbery finish it has!? But then again..i guess the choice is yours..my guess would be that it was a case with a custom paint job because there is no reason why the finish should have been coming off.
toreone said:
Just get yourself a nice black case and with time the purple might wear down. I would much rather do that than ruin the rubbery finish it has!? But then again..i guess the choice is yours..my guess would be that it was a case with a custom paint job because there is no reason why the finish should have been coming off.
Click to expand...
Click to collapse
Yeah, I suspect that color is probably actually "Beijing Pink"...classic mark (no pun intended) of a cheap paint job on a cheap case.
I haven't tried alcohol on this phone so I don't know if it'll affect the finish or not. Sometimes you can get that stuff to come up with a pencil eraser, but only in certain situations. Might be worth a try though.
If you can't take it off with an eraser you'll end up buying a cover. If you use alcohol and can't remove it or damage the finish you're still going to end up putting a cover.
I say you just try the alcohol route. If it doesn't come off then that's fine cuz you were going to slap cover on it anyways. I'd try a mr. clean magic eraser sponge, orange citrus cleaner stuff, goo-gone and alcohol being my last resort. Use Q Tips.
Looks like a bit of moisture got trapped between the phone and the case.
Knowing how tough red stains are to get out, in just about any environment, good luck is all I can say.
i had this same problem with a old nokia i had a blue case on it and it somehow stained the battery cover blue . i tried everything to get it off but i was desperate and said hey let me try some black magic spray on tire shine .left it on there for about five min and it wiped off like butter lol also works good for stickers on car bumpers let me know if this helps .
toreone said:
Just get yourself a nice black case and with time the purple might wear down. I would much rather do that than ruin the rubbery finish it has!? But then again..i guess the choice is yours..my guess would be that it was a case with a custom paint job because there is no reason why the finish should have been coming off.
Click to expand...
Click to collapse
Yes it was :/ the seller sent it with the pink/purple case, looks like it was spray painted (very poorly too). I do have a black rubber case that came with my first one, but i can't see it helping anytime soon..
Yeah, I suspect that color is probably actually "Beijing Pink"...classic mark (no pun intended) of a cheap paint job on a cheap case.
I haven't tried alcohol on this phone so I don't know if it'll affect the finish or not. Sometimes you can get that stuff to come up with a pencil eraser, but only in certain situations. Might be worth a try though.
Click to expand...
Click to collapse
yeah ill give that a try lol seems safe enough. (and the purple seems to be "soaked' into the finish ..at least thats what it looks like..) thanks!
Looks like a bit of moisture got trapped between the phone and the case.
Knowing how tough red stains are to get out, in just about any environment, good luck is all I can say.
Click to expand...
Click to collapse
If you can't take it off with an eraser you'll end up buying a cover. If you use alcohol and can't remove it or damage the finish you're still going to end up putting a cover.
I say you just try the alcohol route. If it doesn't come off then that's fine cuz you were going to slap cover on it anyways. I'd try a mr. clean magic eraser sponge, orange citrus cleaner stuff, goo-gone and alcohol being my last resort. Use Q Tips.
Click to expand...
Click to collapse
Thanks alot guys
The eraser didn't seem to work :/ , haven't tried the alcohol yet but I was wonderin if any of you knew about using acetone, nail polish remover, or gunkOff as far as embeded spray paint removal? (like which route is the safest)
So on the back of my new A500 there's a sticker with barcodes on it. It reads:
L-XE H60PN.002
<barcode>
Reconditioned
XEH60PN0021140B7E41500
<barcode>
I'll take a pic when I can. The sticker is really annoying me (and uglying up my new tab )
What is it, would I ever need it for anything , and can I remove it?
Sounds like its not a "new" tablet then... I think the bit about "reconditioned" gives it away....
As long as it runs good, you don't need the sticker. It was for internal manufacturing uses.
It means, as the other poster said, it was turned in for repair for some reason (somebody probably fubarred it during rom flashings or similar
I would use a damp sponge or cloth to get it moist (careful not to run water into the speakers). Hopefully, once it's good and damp, it should come off.
Lay the tablet on a flat scanner and copy the sticker /take picture and print it. So you will have a original copy. Invade you mess it up removing it.
But warm sponge trick does ideally work without to much distruction to the stickers print.
If itsays warranty void if removed .Call acer and tell them its unacceptable tpbeon there
Good luck.
Thanks guys. Gonna be taking Erica's advice. Yes. Its a refurb.
mtmerrick said:
thanks guys. Gonna be taking erica's advice. Yes. Its a refurb.
Click to expand...
Click to collapse
xoxoxoxoxo
wise choice.
so, as I'm trying to take tthis sticker off without destroying it, well, its not easy. . How do you recommend using a sponge on it? Its a slightly plastic paper sticker.
Try getting the glue damp along edges and pull it over on itself.
If were me I would lay a razor blade flat on the surface and work it slowely thru the glue.being g careful to not scratch the metal.I REMOVED Astupid dealership sticker off the back of my mini van like this.The nurve of them.putting such crap on surface of such a expensive purchased.
Is it possible to JUST replace the back glass on the battery door? Has anyone attempted this? Ive looked and seen that the whole part (glass and door) is around 60 dollars which is kinda pricey and just the glass is around 20 which is alot better in my book so I was wondering if it is at all possible? Thanks for any info!
Nocturnal86 said:
Is it possible to JUST replace the back glass on the battery door? Has anyone attempted this? Ive looked and seen that the whole part (glass and door) is around 60 dollars which is kinda pricey and just the glass is around 20 which is alot better in my book so I was wondering if it is at all possible? Thanks for any info!
Click to expand...
Click to collapse
Yes its possible, you just have to be careful with the NFC and inductive charging coils
lopezk38 said:
Yes its possible, you just have to be careful with the NFC and inductive charging coils
Click to expand...
Click to collapse
Thanks thats good to know. Is there a guide or anything that shows how and where to be careful and whats the best way to remove the glass from the back?
Nocturnal86 said:
Thanks thats good to know. Is there a guide or anything that shows how and where to be careful and whats the best way to remove the glass from the back?
Click to expand...
Click to collapse
Not to be jerk but it's not rocket science. There is no best way to open it. There's only one way to do it. Just take off the back case and replace it with the new one and that's it. don't worry about the stuff inside the back cover. It's glued tight.
Here's a video.
http://www.youtube.com/watch?v=AZDAIgwbXk4
Sent from my Nexus 4 using Tapatalk 2
scream4cheese said:
Not to be jerk but it's not rocket science. There is no best way to open it. There's only one way to do it. Just take off the back case and replace it with the new one and that's it. don't worry about the stuff inside the back cover. It's glued tight.
Here's a video.
http://www.youtube.com/watch?v=AZDAIgwbXk4
Sent from my Nexus 4 using Tapatalk 2
Click to expand...
Click to collapse
Thanks but I emphasized JUST the glass cause thats what I want to do JUST the glass not the entire back cause its potentially cheaper to go that way not the entire back which I know is easier to do but it costs more. I havent seen anyone actually replace JUST the glass which is what I was asking about. Idk if its glued to just plastic and i can break it apart and pry it off then clean and re-glue or stick, or if the nfc and wcharging contacts are glued to the glass in some way or what, thats where I want to be careful
it is possible. the best bet is to go ahead and remove all the glass pieces and that will determine which part to order. be carefule because the nfc and wireless charger are glued directly to the glass so if you rip the nfc or wireless charger you need to buy the whole thing. there is a foil attached to the inside of the back that is extremely easy to rip. mine was shattered into a lot of tiny pieces so it took a long time to remove all of the glass. so now i can just buy the glass instead of the whole back cover. it is a pain but it can be done.
justin g. said:
it is possible. the best bet is to go ahead and remove all the glass pieces and that will determine which part to order. be carefule because the nfc and wireless charger are glued directly to the glass so if you rip the nfc or wireless charger you need to buy the whole thing. there is a foil attached to the inside of the back that is extremely easy to rip. mine was shattered into a lot of tiny pieces so it took a long time to remove all of the glass. so now i can just buy the glass instead of the whole back cover. it is a pain but it can be done.
Click to expand...
Click to collapse
ok interesting i thought it may be like you described. My back isnt completly shattered just by the speaker grill and then its spread out in large cracks so its not a terrible shatter. Do you think it would be easier to remove the glass since it isnt completely shattered? And should I use heat to soften the glue and lessen the chance it rips off the nfc sticker? And would you happen to have pics or know of pics of what it looks like under the glass or with the glass removed? Thanks for your help and info!
I can pull the back off mine later and get a pic. But I'll have to wait until I get off work.
Nocturnal86 said:
ok interesting i thought it may be like you described. My back isnt completly shattered just by the speaker grill and then its spread out in large cracks so its not a terrible shatter. Do you think it would be easier to remove the glass since it isnt completely shattered? And should I use heat to soften the glue and lessen the chance it rips off the nfc sticker? And would you happen to have pics or know of pics of what it looks like under the glass or with the glass removed? Thanks for your help and info!
Click to expand...
Click to collapse
heres some pics. i outlined the foil so you can see where its at. i have a wide peice of clear tape where the glass was at to hold the wireless charger in until i get a new glass. heat definitely helps to soften the glue.
justin g. said:
heres some pics. i outlined the foil so you can see where its at. i have a wide peice of clear tape where the glass was at to hold the wireless charger in until i get a new glass. heat definitely helps to soften the glue.
Click to expand...
Click to collapse
Oh wow thanks man! Looks like there's a few gaps for the glass and the nfc charging coil is loose without the glass. Interesting. I wonder how it will look on the inside after the new piece of glass is placed like messy or as clean as the original look. Do you know what should be used to stick the new glass? I'm still debating if I should do this lol
Sent from my Nexus 4 using xda app-developers app
Im not real sure what to use either but I'd say to use some epoxy of some sort. I don't know if it would eat away at the paint on the back side of the glass or not. So I'd test it on something besides your phone first. I don't think two side tape would stay very well.
I've just been given a weird phone cover. It's some knock-off but I don't mind, the one quirk is that it suction-cups my screen to keep itself (flip cover) shut.
It leaves a weird mark each time, but will there be any long term effects of me using this cover? I know it's a weird cover, but I don't want to damage my phone in any way.
colinhexr said:
I've just been given a weird phone cover. It's some knock-off but I don't mind, the one quirk is that it suction-cups my screen to keep itself (flip cover) shut.
It leaves a weird mark each time, but will there be any long term effects of me using this cover? I know it's a weird cover, but I don't want to damage my phone in any way.
Click to expand...
Click to collapse
The S8 Seems to scratch easier than previous versions I would personally not use it or get a different one straight away.
TheMadScientist said:
The S8 Seems to scratch easier than previous versions I would personally not use it or get a different one straight away.
Click to expand...
Click to collapse
Do suction cups scratch?
Ugh. I was told that the cover was fairly expensive, I don't know how my parents will react to this revelation :S
colinhexr said:
Do suction cups scratch?
Ugh. I was told that the cover was fairly expensive, I don't know how my parents will react to this revelation :S
Click to expand...
Click to collapse
In my history anything can scratch with repeated use maybe put a tempered glass on top The gorilla glass 5 is "softer" than 4 it has a better impact resistance but not as good as before.... I saddens me to see my month old S8 loaded on back with scratches and a few on glass Despite my being in a otter box and extremly careful