Hi everyone. I have a HD2 Tmobile branded. It was working fine until yesterday i turn the phone off and then turn it back on. It wouldnt full booted. It just stuck at the pink (or red) Tmobile logo screen. Its the first screen that appear when u boot the phone up. I tried to connect it with a usb cable to my laptop but nothing happen at all so i can't reflash the ROM. Has anyone able to fix this before? Is there any other way i should try. Thanks
bump. Still looking for help please
Go into Bootloader Mode: While phone is Off, hold Volume Down button then tap the Power button.
Tell us what it says.
i have th same problem its stuck on pink tmobile
went to bootloader n says
PB81120 hx-b3
SPl-2.10.000 8G XE
Micro(LED) 0x05
MIcro(Touch) 0x40
also shows in the bottom white partt serial plzz some one help
mostwanted512 said:
i have th same problem its stuck on pink tmobile
went to bootloader n says
PB81120 hx-b3
SPl-2.10.000 8G XE
Micro(LED) 0x05
MIcro(Touch) 0x40
also shows in the bottom white partt serial plzz some one help
Click to expand...
Click to collapse
Ok your chooses here are:
A: Do a hard reset of your HD2 by holding both the volume up and down buttons down while powering on the HD2 and then following the on screen instructions.
B: Put your HD2 into bootloader and connect it to your computer via USB cable and wait for the Serial to change to USB. Then flash either your stock ROM, a custom Windows Mobile ROM of your choose, MAGLDR if you want to run Android or WP7, or cLK if you want to run Android.
Related
sorry to post again but i got to the part were you have to press the vol-down and power button and the screen with red-green-blue-wwhite comes on and has yellow writing in the red bar:
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0X05
MicroP(TOUCH) 0X30
Then in the white it has Serial in it
but thats it i just stays on there can anyone help please?
flunkyou2 said:
sorry to post again but i got to the part were you have to press the vol-down and power button and the screen with red-green-blue-wwhite comes on and has yellow writing in the red bar:
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP(LED) 0X05
MicroP(TOUCH) 0X30
Then in the white it has Serial in it
but thats it i just stays on there can anyone help please?
Click to expand...
Click to collapse
Hi
Why you press the Vol down and power button? Just press the power button it should load the rom. If it is fail to load the rom then you have to press Vol down+ power to get the Bootloader screen which shows three colour screen.
If that is your case then
Download your device's original rom from this forum or htc website Then connect the hd2 to the PC. THe "serial" sign will change to USB. then double click on the downloaded file. If you use Vista or Windows 7 on the pc Then right click on the downloaded file and Run as administrator. It will flash the rom for your HD2.
im just copying what the sticky says.... im trying to load 1.61, i have just turned the phone on and its still the old rom.
Wen i go in to then bootloader again should i just click the Ruu-1.61 (in windows) and follow the instructions?
ssorry im getting lost lol
flunkyou2 said:
im just copying what the sticky says.... im trying to load 1.61, i have just turned the phone on and its still the old rom.
Wen i go in to then bootloader again should i just click the Ruu-1.61 (in windows) and follow the instructions?
ssorry im getting lost lol
Click to expand...
Click to collapse
Try connecting your phone to pc via activesync and run RUU 1.61.
It worked for me and some other people here.
Good luck.
yeah it worked
the signal seems much better i get H all the time now
Hi,
I've tried to install Android on my HD2, and I guess something has bone wrong.
I've installed the HSPL 3 package, that was ok.
Then I've moved to MAGLDR installation, it was ok until the reboot, after seeing 100% on the installation process, it boot and then get stucked on the starting screen, where you can read HTC with their logo.
I've tried to perform a hard reset. Seems ok, then I press Vol Up. First, the restore time is really short (less than a second), then I press Vol Up again to boot, and I get back to HTC Starting screen...
Do you have any idea about what I'm supposed to do?
Thanks in advance for your help.
Edit :
And when I press Vol Down before power on, I got the 4 color screen with :
On the red box PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
On the green box Nothing
On the Blue box Nothing
On the white box Serial
Benj430061 said:
Hi,
I've tried to install Android on my HD2, and I guess something has bone wrong.
I've installed the HSPL 3 package, that was ok.
Then I've moved to MAGLDR installation, it was ok until the reboot, after seeing 100% on the installation process, it boot and then get stucked on the starting screen, where you can read HTC with their logo.
I've tried to perform a hard reset. Seems ok, then I press Vol Up. First, the restore time is really short (less than a second), then I press Vol Up again to boot, and I get back to HTC Starting screen...
Do you have any idea about what I'm supposed to do?
Thanks in advance for your help.
Edit :
And when I press Vol Down before power on, I got the 4 color screen with :
On the red box PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
On the green box Nothing
On the Blue box Nothing
On the white box Serial
Click to expand...
Click to collapse
Well, pardon me for saying this but you should have searched the forum and google before. So many people have seen this problem before. After hard reset, you don't have anything left on the device so just re-install.
Should work.
Thanks a lot for your reply I feel at least release, my Leo isn't dead
I did actually spent some time over google and this forum, but haven't identified any problems siilar than mine... Sorry about that.
Now you tell me that I'm supposed to reinstall, fine but... how? I know how to when you can connect the mobile to the computer with Active Sync, but without... no idea.
Could you please gie me a clue?
Read this thread carefully.
All of the steps you need are in there.
First you will need to flash a compatible Radio if you haven't done this already.
Then you need to flash the Android ROM you want to use.
I installed android on my HTC HD2 and everything is working except my SD card now only accept 2gb max. I want to flash back to stock ROM, but the problem is Window Mobile Center won't recognize/ not connect with my phone.
So, I want to put WM6.5 back, but Window Mobile wont connect, so how to fix it? Thanks.
solution
u hv to boot up ur phone into bootloader phonr by pressing down volume button and power button...a tri colour screen will appear...then start RUU...windows wil be installed...
cncrim said:
I installed android on my HTC HD2 and everything is working except my SD card now only accept 2gb max. I want to flash back to stock ROM, but the problem is Window Mobile Center won't recognize/ not connect with my phone.
So, I want to put WM6.5 back, but Window Mobile wont connect, so how to fix it? Thanks.
Click to expand...
Click to collapse
The post above me is correct follow their instructions and put your phone into bootloader andd connect your phone to the computer via USB cable and wait until you see the Serial in the white bar of the bootloader screen change to USB and then run ghetto .exe or RUU. You can also flash via SD card if you want. Go here to learn how.
won't work
i tried al the above
i run the HTC HD2_RUU_Leo_S_HTC_NLD_3.14.404.2_Radio_15.42.50.11U_LEO_S_Ship rom
my red blue green white screen saysB 8 11 00 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
I need help. I wanted to install android on htc hd2, i previously had WM 6.5. I formated sd card and put Android rom folder on it...run clrcad.exe and haret.exe. It came to black screen with some text, last line was something about jumping to kernel. It was there like 15 min, i pulled the battery...now it wont start...what to do?
When i plug in the usb it boots up to htc screen and then again shuts and boots to htc screen and keeps going like that.
Bent battery pin.
i now have another problem, i installed magldr 1.13 and now its stuck on htc logo screen...only can pull out battery and go to bootloader...i had radio 2.xx.50.xx...all the text on bootloader is:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
what to do??
Go to tricolor screen. Install stock winmo ROM and make sure the phone boots up fine, etc. Then you can start messing with it again. Note - if you install a stock rom, your hard spl will be replaced.
Did you check the bent battery pin idea? And also, may want to try the thing stated above, but use a custom ROM.
Oh, and may seem obvious but you are holding the power button down when trying to boot MAGLDR right?
Alright so my htc hd2 was given to me by a friend it already had android in it, but being me so stupid i wanted to use windows, and i thought hard resetting would do that, so i hard reset, by holding down the power and volume up and dwn, and it did and it said press volume up to boot and i did that and its been stuck on that screen ever since id appreciate any help i can get, and since its stuck on this screen windows mobile never recognizes it, so someone pleasee hlp me out. thankkss =)
The other thing is I can still access bootloader......
that blue red and green screen when i connect it says USB, but on cpu at device center it never shows up,
On the bootloader in the red area, its says:
PB81120 HX-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
All i want is it to go back to windows mobile, please help mee!!! I already have the Windows Mobile zip along with Radio and all that stuff downloaded, but i need to be guided through so please help me
I appreciate your concern.
Question: When you enter bootloader - do you connect the cable before or after? And what happens when you try to start flashing radio or wm? Does the installer say phone not connected?
/Anders
rickeymann1 said:
Alright so my htc hd2 was given to me by a friend it already had android in it, but being me so stupid i wanted to use windows, and i thought hard resetting would do that, so i hard reset, by holding down the power and volume up and dwn, and it did and it said press volume up to boot and i did that and its been stuck on that screen ever since id appreciate any help i can get, and since its stuck on this screen windows mobile never recognizes it, so someone pleasee hlp me out. thankkss =)
The other thing is I can still access bootloader......
that blue red and green screen when i connect it says USB, but on cpu at device center it never shows up,
On the bootloader in the red area, its says:
PB81120 HX-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x50
All i want is it to go back to windows mobile, please help mee!!! I already have the Windows Mobile zip along with Radio and all that stuff downloaded, but i need to be guided through so please help me
I appreciate your concern.
Click to expand...
Click to collapse
If you run the windows mobile installer (using CustomRUU) when you are in bootloader mode, it will install winmo for you.
Yeah, I installed Windows mob, but when im tryin to install it the first step is to connect to the usb the usb is connected and it still said try8ing to connect then it went staright to error those letters i wrote come up on bootloader screen, somone guide me through this pleaseeeee.