Hi All,
I have an HTC HD Touch which was running Win 6.1 and I flashed the rom to Win 6.5 found on the Rom thread here. It seemed to work ok and was running for about a day. Since then it turned it self off, and now the screen does not come on. It appears to be on as if you dial it ti will ring, but nothing on the screen.....is there a way to flash it back or have I fried it?
Many thanks in advance
hi, strange behavoir, i've you tried to hard reset the phone? or just enter the bootloader?
To enter in the bootloader
Press and keep pressed "vol dn" then press the power button, you should enter in a red, green, blue, white screen.
If you can enter there and your screen is on, then I think an hard reset is what you need.
WARNING, hard resetting the phone will erase all your data on it, not the SD Card just the phone. Just for be sure, take out the sd card before hard resetting.
To hard reset press and keep pressed "vol up" and "vol dn" key and press the power button. Then follow what's on the screen.
Hope it helps.
bye
What I'd also do is check your SPL. If you've flashed a wm6.5 rom you need to have the correct SPL to match. Did you use HSPL or USPL to flash rom? If HSPL, your SPL should state 1.56.Olinex if not then you need to change your SPL. If you used USPL, your SPL should state 1.54.0000. Again, if not you'll need to change your SPL
Follow this guideline here for flashing roms. The symptoms you are describing could be due to you having wrong SPL. Either way, its easily fixed
Related
Hi All,
For the past few months I've been running a DFT NAND build of Android. Yesterday, the phone was running extremely slowly with some odd behavior in the Android menus. When I restarted the phone, loading got as far as the DFT splash screen but then nothing else would happen.
I have since used MAGLDR (1.11) to attempt to boot a fresh Android image from SD card but this hasn't worked. Have managed to use the USB Loader to attempt to flash another NAND build (both Android and WP7) but even though the download process completed, this still didn't work and am stuck in MAGLDR now.
Have read through the forums here and have tried most (if not all) of the suggestions, however nothing seems to be working.
Can anyone offer anymore advice?
Thanks,
Kev
As MAGLDR gets removed if you flash a stock winmo rom I suggest you to try that!
Before you install the winmo rom you can also use Task29 to completely wipe the nand.
good luck
Thanks,
I shall give that a try this evening.
Kev
Unfortunately none of the suggestions have worked. I'm unable to flash a stock WM6.5 ROM as the RUU doesn't detect the phone.
The device does show up in Windows as a Microsoft USB Sync device, however.
Task 29 does not work either due to the same problem.
I've attempted to flash a new Android ROM release but when the phone reboots, it gets stuck on the green HTC logo screen and won't proceed any further.
I don't seem to be able to get MAGLDR 1.13 on the phone either, as DAF.exe complains about some "Config load failed" error.
Any other suggestions?
Thanks in advance,
Kev
*sigh*
you need to read up on "how to flash stock rom from sd card". no need for RUU i believe; sd card method involves copying a file extracted from the stock RUU and placing it in the root of your sd card and letting bootloader detect and flash the file. search for a tutorial or see the stickies.
once you've done that, make a special note about the part that says you need to boot into bootloader (hold down volume down + turn on phone + keep holding volume down until a 4-color screen appears). i suspect you are not doing this step, this is why windows, mtty, etc are unable to detect the device.
if you have already done the above, ignore my post
*sigh* too.
I've already tried flashing from the SD card but I have the same problem. I get to a green HTC loading screen and nothing else happens. I just get stuck in a reboot to MAGLDR and try again loop.
I've read through plenty of posts on flashing custom ROM's and troubleshooting but nothing has helped.
I don't get a 4 colour screen when holding down VOL-DOWN and the power button, the phone just goes into MAGLDR.
Kev
Just to add to that, Windows DOES detect the device but the RUU doesn't. Only the DAF applications find and can talk to the device.
follow me
1. is the battery have enough jiuce? what HSPL you use? hope its HSPL3 2.08HSPL
2. bootloader . . . .
Thanks for your post.
Plenty of juice in the battery.
I believe it is HSPL 2.08 (well, whichever allowed me to get Android on the thing in the first place)
Bootloader what?
Kev
getting into boot loader (4-color screen) is the key to the whole flash with sd card method.
keep trying. read on how to enter bootloader.
i can remember a few ways.
DEVICE IS ON
1. if phone is already on, hold down volume down (keep it pressed HARD)...don't let go of it!
2. push the little reset button under the battery cover. don't let go of the volume down button!
3. don't let go of the volume down button until the 4-color screen appears.
DEVICE IS OFF
1. remove the battery. reinsert it after a few seconds.
2. hold down volume down (keep it pressed HARD)...don't let go of it!
3. tap the end call button and don't let go of the volume down button until the 4-color screen appears.
remember, entering bootloader is the key.
EDIT: it is better to ensure you have sufficient battery. however, flashing via bootloader SKIPS the battery level checks.
kevinwebster83 said:
Thanks for your post.
Plenty of juice in the battery.
I believe it is HSPL 2.08 (well, whichever allowed me to get Android on the thing in the first place)
Bootloader what?
Kev
Click to expand...
Click to collapse
in post 4 you noted you tried task 29 but was successful
you are not even familiar with bootloader, ??? makes me wonder
I'm very familiar with a bootloader, your "bootloader..." comment confused me.
Task 29 was unsuccessful. I've read in a number of posts that you can use Task 29 and start from scratch back at the original bootloader (rather than MAGLDR) but this obviously isn't the case.
Holding down the VOL-DOWN key does nothing other than get me to MAGLDR, which is what happens even if I don't hold any keys down.
I fully understand that the key is entering the bootloader, nothing seems to let me get there.
Kev
kevinwebster83 said:
I'm very familiar with a bootloader, your "bootloader..." comment confused me.
Task 29 was unsuccessful. I've read in a number of posts that you can use Task 29 and start from scratch back at the original bootloader (rather than MAGLDR) but this obviously isn't the case.
Holding down the VOL-DOWN key does nothing other than get me to MAGLDR, which is what happens even if I don't hold any keys down.
I fully understand that the key is entering the bootloader, nothing seems to let me get there.
Kev
Click to expand...
Click to collapse
this is how i enter bootloader from magldr
remove battery
reinsert, leave device off
hold and continue to hold volume down
briefly press power/call button
now your in bootloader
this will show your hspl
Battery removed
VOL-DOWN held
Powered on
VOL-DOWN still held
MAGLDR appears
This isn't my bootloader and doesn't show HSPL
kevinwebster83 said:
Battery removed
VOL-DOWN held
Powered on
VOL-DOWN still held
MAGLDR appears
This isn't my bootloader and doesn't show HSPL
Click to expand...
Click to collapse
if you are now unable to enter bootloader
in this manner, there is only one thing i can think of
you got a bricked device,
you might get some help if you post your querry in the
HSPL thread, or PM cotulla and team
I'm of the same opinion; it is virtually bricked.
The stupid thing is that if I select Android Flasher from MAGLDR, I'm able to flash a different version of Android to NAND but it just won't boot.
Will try a different forum.
Thanks,
Kev
kevinwebster83 said:
I'm of the same opinion; it is virtually bricked.
The stupid thing is that if I select Android Flasher from MAGLDR, I'm able to flash a different version of Android to NAND but it just won't boot.
Will try a different forum.
Thanks,
Kev
Click to expand...
Click to collapse
i discourage you to try another forum
if you got hold of HSPL, task 29 and other stuff here in xda
then this is the best place you can be helped
try to post in HSPL thread
or PM ClydeB1, or bepe.
if they cant help you
then i highly doubt if anyone in this world will
Which HSPL thread would you recommend?
kevinwebster83 said:
Which HSPL thread would you recommend?
Click to expand...
Click to collapse
the original by bepe, cotulla and DFT
I have the same problem...does the HD2 charge itnself in Magldr ?
hi guys i flashed my htc hd2 wm6.5 to nand android rom in 1st 1 week of usage i have no problem and enjoyed the nand android rom in my htc hd2 until one day my hd2 hang and when i reboot my unit it was hang on splash screen only....
i reflashed it using magdlr ver. 1.11 into the same nand rom im using but i have no luck...it still stock on tje android splash screen...what will i do guys?
im planning to flash it to wm6.5 rom,but what will i do?it never boot on tri color screen it only boot on magdlr screen
and how can i flash it wm6.5 rom cook or stock rom i want to revert it back to wm6.5
my hd2 running on gingerbread 2.3.3 nand(V1.8) rom before it malfunction..
Well, my forensic analysis has come up with the following technical and somewhat difficult solution to your present problem: "Click the search button"
Now I know it may sound intimidating, but I tested that feature out for you and came up with this:
http://forum.xda-developers.com/showthread.php?t=905841
matt
Shut down completely your phone (remove batter for 15 sec too)
Place battery back and now hold volume down button.
Still hold volume down button and switch on your phone.
You get 3 color screen.
Now attach your usb cable and connect it to PC
Find on this forum your phone stock win mobile rom (link to officila roms thread)
Run stock win 6.5 rom exe (this is sample name: RUU_Leo_S_HTC_WWE_EastEurope_3.14.479.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe)
Follow instructions on your PC screen. On final your phone reboots.
Enjoy your stock phone.
hi datasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
can i flash wm6.5 rom into magdlr usb flasher?
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
Switch off, hold vol down button in and switch on.
As ClydeB1, states you must hold the vol down only and not hold the power button.
siapelbo said:
hi dasoft thanks for the quick reply...
i try your suggestion to enter into bootloader mode but it booted on the magldr screen...
Click to expand...
Click to collapse
when you get ready to power back on you have to hold volume down and keep holding it while is booting and it should switched to the tricolored screen, plug the usb cable and it should say usb at the bottom when it connects, and if you have hardspl which I know you have after running android, you can use any custom winmo6.5 rom it doesn't have to be an official rom.
can i flash wm6.5 rom into magdlr usb flasher?
No, flash from bootloader.
awts...i cant enter into booloader mode....im so sure what im doing i sure i follow the instructions of you guys....holding down the vol button and switch on
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
I don't think you can flash WM6.5 with flasher. You have to restore from recovery screen by remove battery and restore.
ClydeB1 said:
Are you holding it at the bottom of the button and not in the middle or top, ie as if you are turning the volume down?
Click to expand...
Click to collapse
yeah im sure i was holding down the volume botton and switch the power on
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
ClydeB1 said:
Does the vol down button work normally in the Android rom or when moving around in magldr. To be sure, remove the battery and leave it out for 10 minutes then put the battery back, leave the cover off and try again.
I have heard of one or two users who have also had a problem where the vol down button stopped working. If that is the case there is no way back AFAIK.
Click to expand...
Click to collapse
volume botton is perfectly working it work around in magdlr mode actually i flashed my hd2 into android rom right now flashing is done without problems, but its not boot normarly it boot only in splash screen....
can you guys post a link of task 29...i will try this method and flash stock rom
but the main problem is i cant enter into bootloader mode
I use this tool for Task29 - http://forum.xda-developers.com/showthread.php?t=917807
Once you run Task29 though it will wipe the NAND memory and magldr and if you can't get back to bootloader mode then you will be stuck on the splashscreen.
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
temporary_24 said:
Hi,
I'm also having problems, but in my case the progress bar on my phone when installing the new ROM stops at 0% and will stay there indefinably. On my computer a connection problem will be raised.
The same happens with task29.
I've also tried decompressing ROM Utility, putted leoimg.nbh on my 2GB fat32 formatted sdcard, hold down the volume key.
I will get a new screen with "Loading..." on it, but it freezes there.
So, I have no idea what I'm doing wrong.
Any help will be appreciated.
Regards,
Click to expand...
Click to collapse
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
ClydeB1 said:
Are you sure you still have hspl installed? In bootloader, check your spl version- it should end in hspl.
Click to expand...
Click to collapse
Hi,
Yes. I had one with a 8 on it. I've installed the other, and it worked (or the other way). Thanks.
Regards,
guys my phone revive with a jtag procedure i went to a technician shop here in the phillipines
my phone running in stock rom again...
After flashing MAGLDR113 to install an NAND build my htc get freezed in the startingscreen. I can´t get into the bootloader and i also can´t do an hardreset.
What else can i do to get my hd2 working? I hope you can help me.
maybe usefull:
radio rom 2.15.50.14
Goatrip stock rom
greets schueffi
phone completely off
press power to turn on, but keep it pressed, dont let go.
phone will vibrate as it starts, then you see the first boot screen, (keeping power pressed still) then the screen jumps black with yellow at teh top, keep pressing power until teh menu items apear.
thanks but i´ve tryed that for many times but nothing happend...
is it possible to flash an rom without getting into the bootloader?
have anyone an other idea what i can do?
Not sure if this will help you, but I was being a noob and trying to use the touchscreen with magldr to select a menu item, but you're meant to use the volume up and down keys and the call button to select an item. To flash, select usb flasher. Hopefully that was of help
Hi, is there a solution for this? I have the same problem.
I wanted to install NAND Android on my HTC HD2 device actually running WM and Android on an SD card. I followed all the steps carefully:
I flashed HARDSPL with HSPL4
I updated the Radio version to 2.15.50.14
I installed MAGLDR113 and the installation gave me no problems, but when rebooting, the phone gets stuck in the initial screen and it doesn't either boot or let me go to the boot menu no matter for how long I press the power or the down volume button.
Anybody can help?
Thanks
Dear all HD2 professional,
I got a problem with my HD2 after flashing with a MAGDLR113, it has successful message on my pc, but when my phone restart it always stuck on htc logo.
i search with many forum in xda and try, but still not luck.
My problem is it stuck with htc logo when phone is open. although I try to hard reset (hold vol down + up + power) or (hold down + power), and connect to PC, it do nothing, it still at htc logo.
Now, I don't know what I'm going to do next?
please anyone give me an advice to fix it?
thanks,
dane
You probably didn't set correct radio or spl,, magldr wont boot without 2.08.hspl AND radio 2.07.50 - 2.15.50,,,
Get them both right, magldr will start
thanks samsamuel,
But
Could you tell me how to set radio or spl... or give me a link to do that?
Because I was stuck on htc screen, I can't get out from it.
thanks again,
You already set the spl, that's how you flashed magldr.
Enter bootloader, connect USB, flash the radio, magldr will now start.
here,read this http://forum.xda-developers.com/showthread.php?p=11097380
A few wrong / confusing / potentially dangerous (to tmous) steps listed in that thread. A good read with good links, but use it to help understand the process, not as a definitive guide.
(Example, it says if you have spl 3.03.0000 you should flash a stock rom to give spl 1.42.0000,,,,,, this step would brick a tmous,, when all you needed to do was use Hspl4 to set either 2.08.hspl,, or if the warning about not using Hspl4 scares you, use Hspl4 to set any spl, and then use hspl3 to set 2.08.hspl)
As with all threads, take the info on board, then confirm what you learned by reading other threads.
Many threads are slightly out of date, and so although the info is useful, its not always the easiest / best.
I think you need to root your phone. search on addictive tips.com, you will find step by step tutorial on how to root your phone and install android
Thanks guy,
But i still can't Enter to bootloader.
it should hold voldown + power, it still in htc logo and I didn't see any else even I try again and again. what problem with that or my phone got another problem?
sorry for my misunderstanding.
callme_dane said:
Thanks guy,
But i still can't Enter to bootloader.
it should hold voldown + power, it still in htc logo and I didn't see any else even I try again and again. what problem with that or my phone got another problem?
sorry for my misunderstanding.
Click to expand...
Click to collapse
Remove the battery then ofcourse put it again and do your thing (volume down + power) "hold both":fingers-crossed:
hi
i have used olinex 1.56 hard spl after hard spl phone screen has been black.Phone start but nothing appear on screen i have tried many rom but same thing.Can any one help me please?
Have you tried to revert back to stock ROM?
Reset and press volume up and down button together.
Can you get into the bootloader ?
Do thus Combination " POWER + VOL-DOWN "