I used to have VoiceCommand and BlueAudio perfectly working on my X1. Now this crappy X2 that messes up so much, canNOT run any Audio to the Bluetooth Headset.
It should have the MS Bluetooth Stack so these programs should work. Perhaps it is some registry change that makes them work?
Anybody got them to work and know how to? Thanks!
It seems that the Bluetooth AudioGateway dll files is not working properly. Tried different dll's from different versions but still did not find the "correct" working one. Anybody???
Couldn't get MS Voice Command working.
Vito Voice Dialer works great though.
Haven't managed to make my X2 work with my existing bluetooth headset.
X2 says it's paierd with the device, but then you can't answer calls or anything else.
If it wasn't for the $$$ I spent to buy this piece of crap, I'd have a new phone already!
Okay, is this vito voice dialer dialing VIA bluetooth or not? And HOW do you press a key on the phone to activate it? What key? And just read their manual, they don't even mention any bluetooth capability there. Can you use bluetooth and how?
Because voice command works (more or less) HOWEVER NOT via bluetooth and since there is NO hard/software button to assign to it, it cannot be activated via the phone either!
I have to press the bluetooth button and then the sound (mic and voice) come out of the phone speaker.
I strongly think this has to do with the bluetooth gateway SE is using with the X2. But I was hoping somebody technical could have found a solution by now. For me voice dialing is essential and my X1 was perfect.
With blue audio I could listen to musik on a mono bluetooth!
Just to mention it, I use SE hbh-PV740 and it always works if making 'regular' calls via the phone over bluetooth. But I cannot initiate it nor voice dial.
I can't get my X2 to do anything with my bluetooth kit, so all your questions re: bluetooth I can't answer.
I start vito from a button on the screen and it works.
For me and my phone, the vito product is much more accurate and reliable than voice command.
Related
Can anyone tell me the truth ??? Is it possible or not ?
My previous GSM was a Motorola Timeport. When I had to telephone someone, I just spoke the name of that person, and my Motorola dialled the correct number.
For example I said "Parents", and the phone number of my parents was automatically dialled.
Can I do such thing with my BT headset Sony/ericsson HBH-35 and my Qtek 2020 ???
Some people say it is totaly impossibble ???
I cann´t tell you, if that would work, but i know, that you can use voice dial via some extra software. It works well.
What i don´t know, if you can use your BT for Voice recognition....
Stefan
Aha, thanks Stefan. ( we have almost the same flag - lol ! )
So voice-recognition would work, but only with the microphone of the Qtek itself, pobably not with bluetooth....
So I guess I have to use speed dial in the car...
yes, it´s possible with microsoft voice comand, try it¡¡ it´s very easy to install and very funny.
srlobo said:
yes, it´s possible with microsoft voice comand
Click to expand...
Click to collapse
I assume you mean that voice-dialing is possible, NOT voice-dialing through a BT headset. Right?
From all of the information I have gathered, voice-dialing through a BT headset is just not possible at this time. If you have gotten it to work, I'll bet there are thousands who would like to know how you did it! :wink:
yeah i believe that there is some bluetooth profile required
there are some threads about it somewhere in hacking it forum
Rudegar wrote:
yeah i believe that there is some bluetooth profile required
there are some threads about it somewhere in hacking it forum
Click to expand...
Click to collapse
I have searched and can find nothing that indicates that voice-dialing through BT works yet. There is a great deal of discussion, but no solution (that I can find). I believe that a BT HandsFree profile is required, but not included with the Himalaya BT implementation.
We can certainly hope that one is included in WM2003 SE, should that actually make it to this platform.
some people were talking about if it was possible to use the ipaq bluetooth stack on a xda2 if that works
I'm using Voice Dial sinse 3 month and it works grate. Even in the car I can ask any contact of my data base ( +/-1000) name of contact + mobile or at home etc... The program ask you for confirmation by reading once more the contact name and asks if this is correct.
If you say "yes" it compose the request phone number.
I'm using HBH 65 BT headset for phone and the intergreted micro from Qtek for voice recognition.
Try it for free at : http://www.fonix.com/page.cfm?name=product_fonix_voicedial&ID=14
I have the french version
So Kiyeko -
Are you saying that you can press the button on your BT headset, say a name from your contacts list into the microphone on the headset and the i-mate/XDA II/MDA II/QTEK 2020 will dial the number? If so, I would be interested to know what software recognizes the headset button-press as the initiator of the voice-dialing software.
I have tried Pocket BT Tools with Fonix Voice Dial and was never able to get it to recognize the headset button press as the initiator of the program. Oh, by the way - I tried it with the MS program as well.
Returning to the initial question posted by mvb95.
Yes, with your hardware (Qtek 2020 and HBH35) is possible to use voice recognition to put the calls.
You must install Vito Voice Dialer PE v3.0. Eventually assign a hardware button to the voice dialer. Record all the tag voices you want.
With both devices paired and turned on (HBH35 blinking green), press the hardware button assigned to Vito and say the tag (e.g.: “John”) to the headset. You don’t need to use the Qtek speaker, don’t need to press the HBH35 button, nor confirm the recognition with “yes”, like in the Fonix.
Is simple and ease.
vmgps wrote:
say the tag (e.g.: “John”) to the headset.
Click to expand...
Click to collapse
Are you SURE it is using the headset microphone to input the name? I have downloaded and installed the program, then set a hardware button and recorded some voice tags.
When I press the hardware button, it does not activate my HBH-30 to input the tag, it records it with the device's microphone.
Are you using Pocket BlueTooth tools?
Hi Brian:
I use it always in my car.
My hardware: Qtek 2020 (Rom: 1.72.00WWE, Radio version: 1.14.00) and headset SE HBH-35.
I have tried several times covering the microphone hole with my finger and, by other side, speak to the headset 2 or 3 meters away from the Qtek.
With Vito you don’t need to say “Call John” but only “John”.
I don’t use the Pocket Bluetooth Tools because the latest Rom has the Bluetooth headset profile improved and this software doesn’t work with my car kit handsfree Nokia.
I can’t put my hands on fire, but the only thing I’m sure is that I can talk normally with the Vito Voice Dialer and the headset in my car.
Does any known how to detect when user press answer button on headset? What event or message generated by system? I find only some event that occurs when user insert headset jack in phone.
The AG service gets a "AT+CKPD=200" message
What i'm interestet in ; How do you send these AT commands ?
I'm sorry, but what is "AG service"?
Audio Gateway.
As far as I remember WM5 has standart API to register AG message handler. WM2003SE and older don't have a standart way.
It's not good. I'm interested in WM2003
Voice Dialing via Bluetooth NOT available on Atom
I thought that when I bought my Atom I would have voice dialing over a Bluetooth Headset. My friend has an Exec and it works fine. However, not with the Atom. Even the latest ROM doesn't support it. I have 4 headsets, all pair in Handsfree profile, all have call answering, call ending and last number re-dial working perfectly, but none will initiate voice dialing with the Atom, but all will voice dial with my Nokia 6230.
Therefore it is not a WM5 built in feature and is still ROM dependant. It doesn't matter whether you use the built in voice program, Vito, Neuvoice or M$ Voicedial, the stack simply won't support the AT command.
C'mon O2, it's about the only thing that is crook with the Atom. Other than that it is just the worlds best pda/phone!
Re: Voice Dialing via Bluetooth NOT available on Atom
Camstech said:
I thought that when I bought my Atom I would have voice dialing over a Bluetooth Headset. My friend has an Exec and it works fine. However, not with the Atom. Even the latest ROM doesn't support it. I have 4 headsets, all pair in Handsfree profile, all have call answering, call ending and last number re-dial working perfectly, but none will initiate voice dialing with the Atom, but all will voice dial with my Nokia 6230.
Therefore it is not a WM5 built in feature and is still ROM dependant. It doesn't matter whether you use the built in voice program, Vito, Neuvoice or M$ Voicedial, the stack simply won't support the AT command.
C'mon O2, it's about the only thing that is crook with the Atom. Other than that it is just the worlds best pda/phone!
Click to expand...
Click to collapse
Couldn't agree more!
About voice dialer. I thought it was just because Atom needs bluetooth headset button to be pressed for a while to launch dialer. It acts so with wired headset. Unfortunately, i have just one bluetooth headset to play with. And it turns off after 2 sec. holding the button.
On my Dopod 818pro everything acts like a charm (VD runs after a single press), so it isn't a WM5 bug.
can someone enable activating MS Voice Command from a wired headset for WM5?
it would be greatly appreciated.
Thanks,
I have the same problem using a bluetooth headset but if I use the wired headset supplied with my Atom it works fine.
that's good news. so, many OEMs are realizing the importance of this feature. so far, they have it in the Treo 700w and according to you, the Atom.
btw, did you have MS Voice Command pre-installed in your Atom, or did you buy it separately?
thanks,
The talk button on the wired headset is a "fake" button. It generates an special pattern in the recorded audio that it's recognized by the phone application.
It generates an special pattern in the recorded audio that it's recognized by the phone application.
Click to expand...
Click to collapse
Are you sure about that?
I've disembled quite a few headsets and the usual way is to shortcircut the mic-wire with one of the stereo-wires, whitch in return has to be cought by the mainboard and then translated to a command.
I'm not sure, but seems pretty feasible. That button is only used by the phone applicacion, which needs to open the wave input device.
Detecting the button pressing is pretty simple: recording at 16 bits, the average of the absolute value of the samples in complete silence is at least 100, with the talk button pressed, 6 or 7.
I know most people seem to be adding MS voice commander to their TyTn's but I have that much software on my M3100 that I want to use the Cyberon installed software.. It does just what I need, launch progs and voice dialling from my contacts list..
I don't require anything else except......
How do I get my SonyEricsson HBH-300 BT handsfree to actually use it's microphone when trying to make voice commands..
I was wondering why I had been having so much trouble dialling when driving, reading a few other threads it appears ( and now I've tested it) that the mic only works on a call, it uses the M3100's built in mic to receive the voice command, not a lot of use in a noisy vehicle..
Any suggestions please...
If I need to reg hack, what is the best software to use with the M3100. I tried I had for my OLD pda running wince 2003 but it doesn't seem to like WM5
Any help please... Phil
I have a Vario II with Skype installed.
I realise that Skype recommends that you use the supplied headset when using the product for calling (rather than the speakerphone) but I was wondering if I can use my Bluetooth headset instead of the wired headset?
Bluetooth works fine with ordinary phone calls so I sort of expected it to work with Skype (doesn't the phone just see a Bluetooth headset as a standard headset once a partnership has been established?) - but it doesn't appear to work.
Am I missing something or does Skype for Pocket PC not support Bluetooth? And, if not, why not?
Skype probably doesn't use BT Headset profile. They probably should. But look at how long it took MS to make Voice Command work with BT and on our phones it didn't even work. I bet A2DP stereo headsets would work since it is an audio sending profile and not related to calls but you wouldn't be able to use the MIC except for the one on the phone. This might be enough functionality someone could try if they haven't already. However, there is the utility that someone wrote for the Samsung SCH-i730 that redirect all audio to the BT headset. There is no reason it shouldn't work on any PPC that uses the Microsoft BT stack. So try it out and see if it works.
http://pdaphonehome.com/forums/391448-post1.html
You need to create shortcuts to the toggle executable to make it easy to use.
There is a reg entry that will allow you to patch all sound to a BT headset.
HKLM\Software\OEM\VoiceCommand
LaunchAPEnable should be 0 instead of 1. Once done the headset hardware button will be remapped to connect to the device instead of launching voice command.
You will still be able to press the button to answer calls, it just won't initiate voice dial for new calls.
I would suggest one of those small freeware that allow to remap the hardware button (my button right softw key's been remapped to display a full program menu, that includes the voice command). I'm using a program called New Menu for Windows Mobile 5.
Hope this will help,
Sam
Can anyone share if they have any other methods to use BT with skype?
bsica said:
Can anyone share if they have any other methods to use BT with skype?
Click to expand...
Click to collapse
sorry for the bump... but if this can somehow work it would be a godsend... any ideas oh wise ones?
read my previous post.
To toggle Audio to A2DP you might want to see:
http://forum.xda-developers.com/showthread.php?p=1485391#post1485391
It's an easy way of switching audio to the headset and back to the device. This is for A2DP only.
hey guys,i was hoping for a different thing..is it possible to change the sound from the loudspeaker to the small speaker?? like using a real phone instead of using earphones..i dont have any earphones or bt headsets for the moment so i was hoping that someone can help me out here..its annoying if ur using skype while other people can hear the person you are talking to..
p/s:i've search everywhere including this forum,but still no solution..
No. Apparently it's a flaw in WM: it doesn't give apps access to the phone speaker.
that's a shame..hope microsoft will consider this for their future product
Bluetooth does work with Skype
bsica said:
Can anyone share if they have any other methods to use BT with skype?
Click to expand...
Click to collapse
Try www.Fring.com it has the Skype, MSN, ICQ in there they're all work with the bluetooth. (check the setting after the installation to allow bluetooth headset)
I've done some searches and not found anybody who manages to use MS voice command through a hands free headset.
I've just bought a parrot bluetooth hands free for my car. I'd hoped to be able to use MS voice command for voice dialing. I get the actual phone call through the hands free, but the voice prompts for VC come through the phone and the mic on the phone is used for voice recognition.
I've read people hacking about to get all audio through the hands free, but the hack I've seen disables VC.
Does anyone know if it's possible? Or is there any other software that can be used for voice dialing through the hands free. I'm guessing not if it's htc bad implementation of the bluetooth stack.
Cheers
it is definitely possible - if with BT handsfree you mean bluetooth headsets. With my Jabra BT620s i could use MS voice commander 1.6 and give instructions....it ALMOST works, in the sense that it technically does the job but, at the end, i didn't like it: too sensitive to noise and to....my english....
andrewpmoore said:
I've done some searches and not found anybody who manages to use MS voice command through a hands free headset.
I've just bought a parrot bluetooth hands free for my car. I'd hoped to be able to use MS voice command for voice dialing. I get the actual phone call through the hands free, but the voice prompts for VC come through the phone and the mic on the phone is used for voice recognition.
I've read people hacking about to get all audio through the hands free, but the hack I've seen disables VC.
Does anyone know if it's possible? Or is there any other software that can be used for voice dialing through the hands free. I'm guessing not if it's htc bad implementation of the bluetooth stack.
Cheers
Click to expand...
Click to collapse
I have the same problem - has anyone found a fix?
Incoming calls are fine, also connections that are made after the initial user-to-phone command.
I also have a diamond and this operates just fine ie the MSVC prompt comes through the bluetooth OK.
Thanks
PS yes, I have tried changing HKLM\Software\Microsoft\Bluetooth\AudioGateway
BTAGExtModule =vcbthag.dll to BTAGExt.dll