Being trying for the last few hours to pair with the car kit, the phone discovers the car......the car asks for a code..1234.. which I enter and push OK, the phones says pairing for a couple of minutes and then "cannot connect" at one stage it said "paired not connected" and I had to remove the battery to clear it.
Also when/if I can pair it how do I get it to remain visible so it will automatically connect.
Keith
hmmmmm.... not a nissan car kit, but i do have BT in my car, and it was so easy to pair and use.
i set my phone to be discoveable and let the car find the phone
then when they connected i entered the pass code 1234 (default on most car decks) and it was successful
then i was able to play music via BT A2DP and also call/receive calls in my car
the car and the phone both recognise each other but once the code is put in it hangs, II will try again tomorrow
Related
I'm using a bluetooth car unit that acts as a BT headset. I've succesfully paired it with the phone and it works fine. But if I either turn the unit on and off or walk out of range and walk back in, I end up having to go to "Bluetooh Connections", "Devices", selecting my device, clicking on refresh and selecting the headset service againa and clicking on "Save" to make it reconnect. The car unit is set to poll the phone every 30sec, so after I re-enable the service on the phone, the unit will connect.
Is there any way to either have the phone automatically do this or maybe create a shortcut to perform this operation so it's not so painful to reconnect?
People using headsets, is this necesarry for them as well?
Hi all,
I have the Pioneer CD-BTB200 connected to my car stereo (Pioneer DEH-P6900IB) and cannot connect my X1 to it..
I have searched and found this thread: http://forum.xda-developers.com/showthread.php?t=344216 but the posted solution does not work for me.. I installed total commander on the X1 and looked in the registry for the BT channel of my paired K800i (that can communicate with the BTB200) and tried it with that channel as well without success..
The BT module seems to recognise the phone but gives error message (just displays: ERROR ) when trying to pair the 2 (the 4 digit code I'm using is correct).
Can anybody help me? Would love to be able to make hands free calls again over the car stereo..
*BUMB*
Nobody has a solution? Plz help me out here guys!
I have a Pioneer bluetooth car stereo and when going through the pairing process, I enter the pin number on the x1 and the phone accepts the pairing, the stereo then says "Error". However, i gave it a few seconds and it will eventually paired. I then register the phone on the stereo so it will automatically pair. Now everything works perfectly, better than my Nokia e71 and N95 as these refuse to Auto connect at all.
Nope, doesn't do the trick for me.. I have waited for like 5 minutes withthe ERROR messages in the screen, but it doesn't get past that..
Anyone have any ideas on how to solve this problem?
I have the same Pioneer BT module and also get an error with my Samsung i750. However, after I register the phone with the car unit and then make a few calls from the handset, the phone eventually connects and stays connected until I shut down the car. I was hoping that with X1 I won't have to deal with it anymore, but I guess no such luck Anyway, I think the Pioneer BT unit is very particular and only works with a few approved handsets, I would change the BT unit if I could to something better..
I have the same Pioneer BT module and also get an error with my Samsung i750. However, after I register the phone with the car unit and then make a few calls from the handset, the phone eventually connects and stays connected until I shut down the car. I was hoping that with X1 I won't have to deal with it anymore, but I guess no such luck Anyway, I think the Pioneer BT unit is very particular and only works with a few approved handsets, I would change the BT unit if I could to something better..
Hi, I was able to pair my x1 to my pioneer headunit in my car and get the a2dp to work, but say when I leave the car and it d/c as it should, it does not automatically reconnect when i start the car again like it should, I have to manually go into the settings and set wireless stereo again. Anybody know a solution to this? I am used to my old phone just automatically connecting everytime I start the car. Phone is visible also.
Hi, can I ask how you get your pioneer unit to work with X1? I've tried pairing my Pioneer unit to my X1 and it doesn't connect. Btw, I want to use my unit for handsfree calling. Thanks.
lunguyen said:
Hi, I was able to pair my x1 to my pioneer headunit in my car and get the a2dp to work, but say when I leave the car and it d/c as it should, it does not automatically reconnect when i start the car again like it should, I have to manually go into the settings and set wireless stereo again. Anybody know a solution to this? I am used to my old phone just automatically connecting everytime I start the car. Phone is visible also.
Click to expand...
Click to collapse
Search this forum for A2DPtoggle and you will find a program to easily connect A2DP bluetooth stereo.
I have a parrot bluetooth car kit. Every time I turn the car off I get a message that I lost the connection with my headset and that I have to keep my telephone to my ear.
I don't want this message anymore. Is there a way to set this off.
Yes!
http://forum.xda-developers.com/showpost.php?p=3933326&postcount=1
Gordon
I am having a problem with my car's handsfree and automatic reconnection to my Nexus 4.
My car is paired (and when it is paired I select "Don't ask again" about access to the Address book). However when I return to the car, bluetooth on the phone does not automatically reconnect to the bluetooth handsfree in the car like it did with my previous two phones (SGS2 and SGS3).
I can go into bluetooth settings, and click on the handsfree device and it connects right away and works fine, but I really don't want to do that every time I get in my car.
Does anyone have any suggestions?
Thank you.
bump-- anyone?