Database Users

do you use a screenprotector?

Do you use a screenprotector on your trinity? I do, one from Brando, but I don't like it and am thinking about removing it...
Is anyones screen already damaged?

Is it possible to put it perfectly at all ?! I mean I must be in a totaly sterile envoirement with gloves and special suit and God knows how and what skill I must have to put it right
My Trinity is one day old but I will surely remove it in a couple of days, can't look at it with this ugly bubbles beneath

The first thing I do when I get any new device is get a screen protector for it, and it goes on before I ever start using the device. I've gone through a lot of PDA's over time and one thing I can say is that you get better at putting on the protectors and you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
The best way to put the protector on is to carefully peel just a bit of one edge and line it up at the top of the screen. Then use the included card to slide the rest down the screen, the paper backing will peel off as you do this and it helps to prevent bubbles and dust getting on the stick side of the film.

If you don't like bubbles, try a brand that is not adhesive. Most people don't like the type that slips under the case but I do. I've been using NuShield protectors for a couple of years on 4 different PDAs and they are great IMO. I don't use a case (store in pocket) and NuShields are very durable - easily lasting 6 mo.

I'm using a brando ultraclear for K-Jam in my p3600... it works perfect... I haven't any sort of bubbles because i put it the first day i got my new device.. so device under it was very clean and the result is PERFECT

shoey5 said:
...you get used to the odd bubble or piece of dust underneath. It's far better than what happens to your screen without a screen protector over time.
Click to expand...
Click to collapse
Completely agree!

I'm using Covertec Screenprotector(for S100), and it works like hell!
The screenprotector is about 1-1,5 mm thick, so it's pretty thick compared to many other brands, but the advantage is that it's almost impossible to get airbubbles, and the screenprotector is 110% clear! So you won't even see it's there!
Comes in a pack with two protectors, one with UV-filter, and one which is ultra-clear...
Can highly recomend them... No need for a "anti-bubble-wiper-thingy"

1.5mm thick?!?!?! That's thicker than a "anti-bubble-wiper-thingy". I have wetsuites that thick. You talking about a case or a screen protector?
LOL
No offense - just having fun. Some are actually quite thick in comparison.

Hehe! Well, ok; maybe it's a bit thinner... But it's about the thickness of a playing card, and just as stiff as one too...
And no, it's not a casing, or a wetsuit... Maybe a drysuit haha!

I use protector, but got 2 bubbles which I want to try to remove.
Can anyone tell me how to remove the protector without using anything thin and sharp?
Asbjørn

Tape. Take a 1-2 inch long piece of tape and press one end on a corner of the protector. Then pull

I can't get my screenprotector removed...not even with tape

Hate screen protectors. Don't use them. My nephew has a Jam which is years old and hasn't had a protector. NO screen scratches -- only a little dullness where the SIP keyboard is but that buffs out in seconds once a year using Displex. No scratches from keys even though it's subject to some abuse and the casing is scratched and dented. Thus I myself have no crap on my P3600's screen.

Im not a fan of cases or screen protectors, but I got 1 for my p3600. Its pretty good, I just wish it was about 2mm wider, since the left edge doesnt quite go till the very end of the screen which is annoying.

I got my screen protector from 'Javoedge.com' , it cost me about £8.50 but it is worth every penny.
It is cut to the exact size of the Trinity screen and fits really well. It is so thin that it slides beneath the White plastic case of my Trinity and the screen itself, so there are no edges of the screen protector to be seen.
I agree that you must take your time when installing it to try and get the edges straight, but when it's on it fits and looks great.
I opted for the super clear version and not the anti-glare version.
Great product!

Invisible shield from ShieldZone.com
I'm using an "Invisible Shield" from ShieldZone.com for my P3600. At the time I got mine, it didn't exist any pre-cut version for the P3600, so I ended up with a pre-cut TyTN shield, since they have the same screen size.
The first 2-3 days the result wasn't that good as I had some bubbles under the shield, but they disappeared after some days.
Watch the demo videos on ShieldZone.com, and I guess you will be as impressed as I'm with this shield.
-Bjørn

Hi people.
I am soon gonna be a happy owner of a Trinity and i will definately buy a screen protector for my device. Can you please give me your opinion on different brands you have tried?What brand would you recommend buying?
Thanks

I have a Brando one that they now market as a P3600 version.
It sticks to the screen with static so no glue or residue if you remove it. Also this means it is washable too. The static provides more than enough force to keep it on the screen. In fact it is stuck fast. Only by pulling a piece of tape stuck to it by both ends will remove it.
My only problem is more with screenprotectors in general. Since they add extra thickness to the screen they do affect the sensitivity of the touchscreen. So for a while you will write with the stylus and you wont be using enough force. You get used to it, but it would still be nicer to find a thinner membrane.

Mine is a Clear Touch Crystal from Boxwave. I've used Boxwave's products for years and found them to have very high durability and quality. The screen looks like it has nothing on it at all when the device is on. I find that it actually seems to improve touchscreen accuracy and feel.
The only problem I have had with screen protectors in general is that if they are cut too close to the borders of the screen, that is, if they fit too well, they seem to interfere with the screen's ability to detect taps. I think it is interfering with the digitizer. Every time I have installed a protector PERFECTLY leaving no gaps on any side, the screen stops responding until I remove the protector and reinstall it with the edges trimmed in about 1 mm on all sides. I don't think that you need to have all edges trimmed, but I do it for uniformity's sake.
Hope this helps someone who gets a protector and then thinks they broke their device by installing it like I did my first time.......ahhh to be young again.....

@olsenbjo
Does the Invisible Sheild cover the entire device, or just the screen?
Thanks!

"Rigid" Screen Protectors?

Having recently bought my son a Nintendo DS, I noted that in the accessory pack I got with it, it came with 2 screen protectors that are semi-rigid. They're quite a bit thicker than one that shipped with my phone, and don't flex and bend like thin paper. They also don't seem to affect sensitivity of the touch screen in any way, as well as being perfectly sized to the screens and were invisible once fitted.
Are there similar protectors for the TyTn 2? I'd love such a protector as it'd be FAR easier to fit, and provide much better protection to the screen.

Rigid Screen Protectors
I have come across these. The ones I tried were made by "Martin Fields" product number MFOP-HTCTyTN-T
A right bloody bastard to fit as they are very slighty oversized. Perhaps this is done purposly so the protector fits into the gap around the edges of the screen?
Very clear and reasonably priced compared to the OEM product. They do work extremely well (once fitted).
Rgs,
J

Thanks. I'll check em out.

invisibleSHIELD.. That's all I have to say.
oH, view the demo also.. its well worth it.

I just checked my little brother's DS box, hoping to find the screen protector but nothing there but manuals =(
Any reference on how firm and rigid the MField or InvS are?

Well, from the video, the invisibleShield isn't the slightest bit rigid, though if it lives up to its claims, that wouldn't matter. I ordered a Martin Fields one earlier so I'll see how good that is.
It's not just the rigidity for protection though. A rigid protector will be a LOT easier to fit...

Beleave me, MF is rigid. And yes, it is easy to install but remember to clean the surface of the screen. This part is very important. If you do it right, it will install in less than 30 seconds and you will struggle to see the difference between no protector and MF.

Oh I know that. I'll be cleaning it very carefully and making sure there's no dust about when I fit it! Don't want dust under the thing!
Just wish it'd hurry up and arrive!

boxwave
The boxwave protectors are much thicker than average ones, are washable, and work great. They are about as thick as the psp protectors, e.g. more like a hard plastic sheet, I'm not sure what the ds ones are like.
http://www.boxwave.com/products/cle...crystal-screen-protector-htc-tytn-ii_2905.htm

tke371 said:
invisibleSHIELD.. That's all I have to say.
oH, view the demo also.. its well worth it.
Click to expand...
Click to collapse
FYI, a warning this could break your Tilt!!!!
This shield rocks. However it's a risk for the Tilt. You have to apply water to the back of the protector to get the bubbles out. I applied water, shook the excess water off before applying.... and stuck it on.
I used the included squeegee to get the excess water out of the shield along with the bubles. I wiped extra water away. Next day, my screen was dead (colors were washed out and glitches). Apparently during the squeegee process water slipped between the screen surface and the edge of the bezel around the screen, and in to the phone, and got under the LCD plastic into the LCD itself.
I do use this product on my $2700 SLR camera. There's no bezel on the LCD so the squeegee'd water comes right off, and won't get in the camera.
Beware. I had to get a new Tilt because of this, and it'll be a cold day in hell I use this product on any item with a bezel where water can seep in.

Semi- related: how are you guys cleaning your phone screens?
Oh, and +1 for Martin Fields.

My phone broke, but I had insurance on it (not from phone company but through homeowner's via a personal property rider), and mycellularrepair.com was able to replace the LCD for $200. Also, never buy that phone company insurance. Personal property rider is the way to go. It was just pennies a year for ~$500 of coverage for the phone. NO DEDUCTIBLE! So I paid nothing to have my phone fixed.

Get a NEW ONE - They're Cheap
jon_k said:
FYI, a warning this could break your Tilt!!!!
This shield rocks. However it's a risk for the Tilt. You have to apply water to the back of the protector to get the bubbles out. I applied water, shook the excess water off before applying.... and stuck it on.
I used the included squeegee to get the excess water out of the shield along with the bubles. I wiped extra water away. Next day, my screen was dead (colors were washed out and glitches). Apparently during the squeegee process water slipped between the screen surface and the edge of the bezel around the screen, and in to the phone, and got under the LCD plastic into the LCD itself.
I do use this product on my $2700 SLR camera. There's no bezel on the LCD so the squeegee'd water comes right off, and won't get in the camera.
Beware. I had to get a new Tilt because of this, and it'll be a cold day in hell I use this product on any item with a bezel where water can seep in.
Click to expand...
Click to collapse
Interesting - Are you really that concerned about a product which is relatively cheap compared to the amount of time use you get out of it? Forget washing it off. Just put another one on - a CLEAN NEW one. If they last a long time (like in most cases a year or more), who cares that you have to spend around $20 to get a replacement. If they stopped making them altogether or they cost a ridiculous amount of money (for plastic, ridiculous. For peace of mind, priceless), then yeah, I would wash and rewash the screen to save money.
And the idea is NOT to squeegee the WATER bubbles out to the sides. They will evaporate on their own given some time. The idea IS to squeegee the AIR bubbles out to the sides and also to take extra great care when doing this procedure. You wash it off so that it restores some of the tackiness on the film. You can get most of the water off by blowing or using a can of compressed air, THEN put it on. You shouldn't have that much water under your film if you take care when doing it.
I am sorry about your tilt. That really sucks. If I were you, I would just put a BRAND NEW one on next time and forget about washing it off.
~Gwen

I need one of these too, recently the digitizer for the touch screen on my phone cracked. They are charging me 50$ for the screen and 40$ for labor. My question would be, would this rigid screen have prevented my digitizer from breaking? If it would then id buy it in a second.

I'm giving a +1 to the Martin Fields as well.
I just got a couple of them for my phone. They're definitely more rigid than some of the others, but I put it on a clean screen & can barely tell I have one on.
Stylus slides smoothly across it, no visible scratching at all (unlike the OEM one that marked easily), & it's also pretty smooth for finger usage too.
Had to wait a week for them to ship via expansys-usa, but worth the wait.

screen protector yes or no

any one with recommendation on screen protector

I'm currently using a Zagg max coverage protector that I had installed at Best Buy, and have no complaints so far. The only thing I've noticed with it is that my finger tends to get stuck when using Swype, but not often enough for it to bother me.

I don't have this phone but I don't think you need a screen protector. I haven't seen any videos on the screen durability test like they do for the iphone scratch test. But I think the screen should be sturdy enough. The screen won't be as smooth to scroll with a plastic layer. And if you accidentally get even a drop of water in the corners of the phone with the squeegee, you are screwed. Good luck.

Using an Invisible Shield on mine. This is the only phone I've ever used one on. I figured with a screen this huge I want to keep it looking nice.

You don't need you it is glass like the Iphone and hero. I have seen test's on both using key to try and scratch nothing happened. Anything that would damage the screen (scratch it) would go right through the screen protector and still damage it. As it would take a lot of force to scratch. Just a wast of money not to mention it hampers the touch screens ability to pick up your finger.

someone apparently water damaged their evo with putting on a protector. Careful. I would cover up the indicator on mine once I get it.

i have a zagg on mine and hate it. its sticky and has a "orange peel" like appearence. i ordered a hard plastic one on amazon and am waiting for it to come in the mail.

I also feel that a screen protector is unecessary...glass is very hard to scratch, and can only be scratched by something harder than it is.

Zaag one here and I think it's too sticky. It messes with my swiping. Catches my finger too much.

chazglenn3 said:
I also feel that a screen protector is unecessary...glass is very hard to scratch, and can only be scratched by something harder than it is.
Click to expand...
Click to collapse
I used the same logic with my hero and ended up getting a few scratches just from unforseen sh!t happening. this screen is too beautiful for me to risk.
also whoever water damaged their phone while putting on a screen protector is an idiot.

I put one on for peace of mind and it works just as it did without the protector.
However, if it's like the iPhone screen, then you shouldn't need one at all. I had the same iPhone since the release date and had zero scratches as of Friday... it's last day in service!

We pre-ordered out Evo's at RS so we used out accessory credits for Zaggs and car chargers and I put them on. They do have an orange peel like look when looking at them at a angle with the screen off and reflecting off some light. But with the screen on and looking at them there is no issue with the display. They were not hard to put on either.

I'm using the "anti-glare" protector that comes in the 3-pack you get at the Sprint store for $12 (the other two are "clear"). I love it - it doesn't interfere with my user experience at all. Why on earth would you risk scratching your screen? To save $4 and 5 mins time?

Boxwave Crystal Clear screen protectors. I have a 3-pack on order (I have 2 Evo's between me and my girlfriend). We're using them "naked" so far until they arrive.
I highly recomend the Boxwave protector though, I have used them for about 6+ years on various PDA/Smartphones. I even have one for my P&S Camera.

Here is my experience:
Zagg:
Good -
Works well as protection
Hides fringer prints decently
Bad -
Blurs your screen a very small amount
Makes the surface feel like rubber
Hard to put on without getting a little dust under it
Generic hard plastic sheet:
Good -
Works well as protection
Feels very smooth, smoother than glass
Easy to put on, and normally you get 2 or 3 in case you make a mistake
Perfectly clear
Bad -
Finger print magnet, oil really builds up
You can see where the protector ends around the edges
Added glare in sunlight(small amount)
Unprotected Glass:
Good -
Feels very smooth
Easy to clean off, just rub it off on your shirt
Perfectly clear
Bad -
Medium finger print problem, but easy to clean
I feel scared to place it face down, once I get a case that recesses the face I will feel better.
Over all I decided to go with unprotected. Its the middle of the road and I feel the best over all experience.

Zagg Invisible Shield is NO GOOD.. Its almost sticky. Don't get it! I warned ya.

zone23 said:
Zagg Invisible Shield is NO GOOD.. Its almost sticky. Don't get it! I warned ya.
Click to expand...
Click to collapse
Agreed, the Zagg is sticky. But I deal with it so that I can protect it. I don't have a huge issue with viewing it or the orange peel look when it's off because you don't notice it when it's on. The fit is nice. On my hero, I had a really clear smooth one from ebay which was great, but was all scratched up. The zagg shouldn't even mark up which is why i'm dealing with it. Sticky, but not to the point that it pisses me off. I put it on myself relatively easily, just spray lots of that solution on it, no bubbles, no dust, 2 minute application.

Maybe the Zagg is sticky if you put it on backwards but I have ZERO complaints about mine.

I ordered a 3 pack of anti-glare/anti-fingerprint screen covers from handhelditems for 7.99 (for the 3pack). They have crazy deals on evo 4g accessories right now. I also got a car charger for like 3.99.
I bought it more for the anti-glare/anti-fingerprints than the actual screen protection.

Warning!
There is a whole thread started on water damage and most of this comes from any screen protector that requires you to spray on water... ei Zaggs
When you squeegiie the water off the screen it leaks in to the back of the phone and Sprint has been sneaky about placing water damage indicator right on the tip of the phone.. below battery.
Either cover the indicator with protector or stick to the regular screen covers..

hi guys, kindly recommend a i9023 full body screen protector.

as topic
hi guys, kindly recommend a i9023 full body screen protector.
I've been looking tru ebay, amazon. but not yet to find a satisfied ones

I love my Bestskinsever skin. $10 for full body. You have to make the solution yourself though.
Sent from my Nexus S using XDA Premium App

I got myself an InvisibleShield from Zagg. It's not easy to install.. the back side of my phone got some bubbles stuck in there. The front side was better though. However sliding your fingers across feels weird... there's always some rubberized layer that you can feel and creates traction sometimes. Then it gets a bit sticky and if you leave your phone on a glass surface for example, when you pick it up you can feel that it's unsticking from the table. And then you've got an orange peel effect on the screen. Moreover the shield collects finger prints and dust around the key holes but hey... at least you've got peace of mind about your screen not getting scratched. I for one, can live with the above mentioned issues besides at night it looks great... only by day you can see better the imperfections but still you don't have problems with the screen being reflective by day.. you can see well what's going on.

I always get zagg and let best buy put it on. I've tried many times. I've tried doing it the way they do but it still looks like **** when I'm done. They do a much better job than I ever would. I let a sprint employee put one of theirs on once. They did a ****ty job on it. I tried doing that myself at home, taking a long time to try and cut the plastic to be the exact size as the screen. I failed miserably when putting it on and getting all the air pockets out. Get a zagg at best buy and pay them to put it on. Don't mess with the screen or put a case on it for at least a couple hours. Overnight is better. I didn't do that once and every time I put the phone in my pocket, the heat would make the zagg slide on the screen. After that I give it a few hours to dry and set. No problems now. That's why they they say to not roll down your windows for 24 to 48 hours after you get tint put on a car. The liquid needs to dry and the adhesive needs to set properly.

I'd have to recommend the ZAGG as well. I always buy from ZAGG.com that way if anything goes wrong the warranty/replacement is easy, plus it's usually cheaper. There's also a technique called palming with helps a lot with getting the corners to stick, they even have a video on it.

I use Steinheil Ultra Optics. I love the matte feel to the screen and it reduces glare. Also it doesn't yellow!

Hey i bought Steinheil Ultra Optics and kind of disappointed with it. It's not fitting into my i9023.....
Pros
- no finger print.
- good feel on sliding e screen with my finger
cons
- no warranty
- doesnt fit. protector too small!
- too expensive for a ****ty protector w/o warranty.
I will not recommend Steinheil Ultra Optics!
Who has a satisfied screen/full body protector for i9023 plz recommend..haha

I bought ghost armor ones for my nexus s and the wifes iphone 4. Followed the directions and did the iphone first. It looked like ****. Took it off and decided not to do my nexus. Will probably return them, and just be careful with the phone.

xoskins and xtreme guard screen protectors

Hiya guys,
I was just wondering if anyone else has either used xoskins or xtreme guard protectors and been left feeling disappointed? I originally had an SGP ultra on my nexus 4 but I was feeling a little annoyed that it didn't cover the full screen. Other than that they're perfect, nice screen hardness difficult to scratch and leave the screen looking amazing. I really thought the xoskins one would be perfect so I paid the price and ordered (shipped from US to UK).
Finally arrived, installed straight away. Let me just say I've fitted lots of screen protectors before to various phones and I'm pretty good at it. So much so friends and family ask me to do theirs for them. Still, the xoskins one felt a little fiddly. The solution they provide makes it very slippy, so using the squigy afterwards made it squirm around which was annoying. Also, even though both sides were wet the squigy still left slight burns after only 3-4 swipes. It took a full 48 hours for it to dry.
The cut on the protector was good, and it was nice and clear. It seemed to leave a slight orange peel effect across the screen though, and I had 4-5 thin rainbow type lines/scratches about 1cm long on the one side which were clearly on the underside of the protector (all perfectly straight and all facing down perfectly so I'm thinking manufacturing fault?). The feel of the protector was frankly awful. It flexes under finger and restricted swiping somewhat. Worst of all, any slight knock leaves imprints. I tested it by lightly rubbing my nail across it, it left a clear mark that was there for 2-3 days! It flexes way more than I'd like, I can't see it providing much protection from knocks tbh. Granted I wouldn't do this in normal usage but any other knocks left imprints too.
So I removed it, and thought I'd try the xtreme guard. My god, I've never used such a rubbish protector. The cut is dubious at best, the screen clearly looks worse when its on and it suffers from the same indentations and flexing as the xoskins ones.
Maybe I've been spoilt by the SGP ones (I still have the back protector SGP skin on there as its a perfect fit as its flat) or maybe all wet application protectors are like this to be more flexible for the curved glass?
Either way I've ordered another set of SGP protectors and I'll put up with the exposed edges. I'm sure there's people out there that are happy with their protectors, but I just wanted to share my experiences.

Wet applied screen protector can never compete with the dry one..even the $1 junk one.
I took off my Xtremeguard and using the junk that came with my nillkin case..which is still much clearer than the xtremeguard.
But I keep the back of xtreme since it make it less slippery.

Glad its not just me who found this then I can see how having a *stickier* back protector could be beneficial. The SGP one I have is still rather slippy. Hoping it will help strengthen the back though in case it has any accidents The SGP ones saved my iPhone 4 before. One was a drop from my ear onto a wooden floor!

It's nice to read that I am not the only one who dislike the Xtreme guard screen protectors.
I just cant believe how sticky it feels and how much it gets scratches and dents.
I've got a fillkin flip case comming my way as well so I think I'm also going to replace the front xtreme guard screen protecotr with the nillkin one.

One thing to keep in mind for all wet protectors is that when you need to push out the bubbles, never used a squeegee. It is very difficult to avoid burns on the surface with a squeegee. Instead wet your finger tips and push the bubbles out with your finger. Much easier and doesn't leave burn marks.
If you absolutely need to use a squeegee, the paper one provided by SGP (ironically) is pretty good for wet protectors. Use the corner as much as possible and don't push too hard.
I myself prefer dry protectors as well but there are indeed some good things about wet ones. They are very scratch resistant, provide more grip, and doesn't show finger prints as much.

The xo skin i have is trash the front has so many random Knicks and bubbles and stuff the back does too but I'm going to leave that on and just use these 3 for $5 screen protectors from amazon until the glass protector comes out with reviews
Sent from my Nexus 4 using xda app-developers app

I am using the XG and granted it has it's orange peel look to it, but I don't mind it. The look reminds me that I have a sp on and I can safely put the phone in my Seidio holster without looking. LOL.
Yes, the screen looks way better with a dry sp on, but I am happy with the cutouts and fitment. And plus doesn't affect the Diztronic Ultra hard case at all when taking off or putting on. Which is good IMO.
Am I 100% happy? No, I say maybe 96%. But for the price of 3 front and backs for 6 bux. I can't really complain too much.

Xtreme Guard are excellent. You just need to take your time applying it and pushing out the bubbles. Minimal orange peel and the protection is perfect around the curved edges.

After having mine on for nearly a week i'd still disagree. I have no bubbles or marks on the xg but it does have the black spots issue I've read about which suck! The cuts off on mine everything is aligned perfectly with screen edges but 1/4 of the camera lens is covered. Honestly its not how I fitted it. The feel is also pretty bad. I genuinely cannot wait until I get my new SGP ones.
Xoskins replied to my email about 4-5 days after I showed photos of the defects. They are sending me out a new protector at least. Will probably sell it on eBay to claw back some cash.
I'm not going to bother emailing xg as they're cheap and tbh I won't be going near their protectors again!
Sent from my Nexus 4 using xda app-developers app

The problem I had with XO Skins was that the protector for the back of my n4 had a little pin hole in it! Luckily they are replacing it free of charge, including shipping! Which is good cause I'm in the UK and did not want to pay to send it back to the US.
The protector for the screen however has been brilliant, I've had it for about two weeks on there and the sort of rubbery feeling goes away and it feels very similar to the glass on touch. If a little more squishy. It does not drag against my finger anymore.
As for bumps leaving marks, I've noticed that, but they always go away within about thirty seconds.
All the bubbles have disappeared on my screen and its very clear.
I definitely agree with the OP about the application process though, the solution makes it very slippery, which is good when trying to position the skin. But when using the squeegee to push out the air bubbles and liquid the skin moved everywhere. After that though, it dried family quickly, did leave it overnight anyway.
I'd say I'm pretty pleased with my XO Skins purchase.
Sent from my Nexus 4 using xda premium

Confused_Cheese said:
After having mine on for nearly a week i'd still disagree. I have no bubbles or marks on the xg but it does have the black spots issue I've read about which suck! The cuts off on mine everything is aligned perfectly with screen edges but 1/4 of the camera lens is covered. Honestly its not how I fitted it. The feel is also pretty bad. I genuinely cannot wait until I get my new SGP ones.
Xoskins replied to my email about 4-5 days after I showed photos of the defects. They are sending me out a new protector at least. Will probably sell it on eBay to claw back some cash.
I'm not going to bother emailing xg as they're cheap and tbh I won't be going near their protectors again!
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
That's no even possible.
Pics?

narta said:
That's no even possible.
Pics?
Click to expand...
Click to collapse
Why not? I'm talking about the front facing camera not on the rear. My SGP ones arrived this morning so the xg one was ripped off almost straight away so unfortunately I can't take you a photo to show you.
The cut was definitely off, there was some extra material right in the dip of the cut out that goes around the lens as if it hadn't been cut cleanly. The dip wasn't rounded like it should of been. Maybe I just got a bad one in this respect, but it shows there is very little quality control. Especially as mine also suffered from the same black spots I've seen elsewhere.
The bottom of the protector was literally up against the chrome rim, I couldn't of positioned it any lower so it wasn't due to bad positioning. It was just poorly made.
I've just ordered a Nillkin case which will hopefully help protect the bits of glass the SGP ones miss. The feel and screen clarity is so much nicer!

Well, xoskins replacement arrived today. It had been put into an envelope that has a bright blue lining and the edges of the protector now have a lovely blue haze. Great! It didn't even have a piece of card in to stop bending etc. so lucky it survived at all.
Not even worth trying to sell it, If I purchased one off ebay myself and it had this haze I'd be gutted. Really disappointed with them.
I did notice they seem to of changed the design too. My previous xoskins one had a U shaped cut out for both the front camera and the proximity sensor. This new replacement has O shaped holes for both so that there is something actually protecting the top edge all the way along.

That sounds like your first one was a case fit and your new one is a full skin. When I got a replacement it came sealed in a baggy, crazy. I would hit them up again.

stretched said:
That sounds like your first one was a case fit and your new one is a full skin. When I got a replacement it came sealed in a baggy, crazy. I would hit them up again.
Click to expand...
Click to collapse
The first one I had definitely went right up to the chrome edges on every part other than the top by the proximity sensor and camera where there was a U shape.
I'll drop them another email and see what happens. They can only say no.

Well, what can I say? I'm using the xg for the front and for the back of my nexus 4 and I'm very pleased with it. I have them on for about 2 weeks now and everything is well..
The cut of the xg protector is one of the best out there. In my past galaxy nexus I used a clear screen protector and every 2 months I had to change it with a new one because of the dust that got under it... Causing to many bubbles.
That's not the case with the xg protector. This thing is not going anywhere.. And I also use it with the official LG bumper case with no problems..
I'll try to upload some pictures for you to see.. The only disadvantage is that the feel of the xg protector is worst from other clear screen protectors, using the dry install method.
Στάλθηκε από το Nexus 4 μου χρησιμοποιώντας Tapatalk 2

narta said:
That's no even possible.
Pics?
Click to expand...
Click to collapse
I agree. You must have a defective one. My second set has all the correct cutouts. Here's my with the XDA case with XG front and rear protector on. The link is to the front.
http://forum.xda-developers.com/showpost.php?p=36718215&postcount=7