hd2 T-mobile only usb detect ''qualcomm diagnostics interface 3197" - HD2 General

Hi. Hd2 T-mobile Have stitched as usual HD2 Leo. Now it is defined by the computer as "qualcomm diagnostics interface 3197". Whether there is a decision that it to cure or only JTAG?

I have the same problem.
Question - is it possible to restore this device?

i'm assuming you flashed a ..51.. version radio? if so, currently no known fix.

I do not know what happened to him.
The previous owner said that updated the firmware, but what specifically - could not find.
Is it possible to somehow check?
Phone does not go into bootloader mode.

well if it wont turn on at all, then no theres no way to see.
however, the most common "brick" on tmous (t mobile us) phones is flashing a non tmous radio. the symptoms are.... won't power on, no charge light when plugged in to charger, and shows up on the pc as qualcomm.
there is currently no known fix.
you could get it fixed under warranty, but you will probably need to go through htc, t mo probably won't help if you don't have a proof of purchase.however you proceed, don't mention flashing, cos they will charge you a few hundred dollars for a new circuit board.

Flashing through JTAG interface will be able to solve the problem?
If yes, are there circuits and software?
Or only specialized devices and software?

HI. have you solved the problem??? my Tmous is brick. Can you help me???

qualcomm = brick

Related

htc typhoon dead

hi , I have a htc typhoon (amadeus) based qtek 8100 phone , by mistake I upgraded bootloader to a htc wizard bootloader rom ( IPL/SPL 1.01 ).Now the phone isn't opening turning on or powering up.When connecting to usb nothing happens.Sometimes, it blinks all of the keyboard lights (maybe sometimes that I play with key combinations). How can I repair and put the right bootloader into phone again ?
Note1: I am pressing cam button and connect usb cable nothing happens.
Note2: I can't access to the bootloader screen[/quote]
I and several others have already replied to you on this and several other forums. You need a service centre to flash the phone using JTAG points directly on the curcuitboard.
Asking over and over isn't going to change the fact that with a screwed bootloader you need to flash using JTAG. Do you think the more times you ask somehow it will be different?... :roll:
Richard
No other way ?
May anyone have JTAG schematik for Qtek 8100 ?
sorry wrong thread

ROM or the motherboard ?

I attemted to flash my Kjam to WM6 & it went dead. It wont start at all. Kjam Service centre says there is a problem in the mother board and it needs to be replaced for $ 300+........now if flash fails...the ROM must have gone corrupt , what has it to do with the motherboard ?
can anyone throw light on whats the real thing ?
Deven.
take out the battery for hours then re-install it. try to boot in bootloader mode first(3 colors). If it work, it's the time to re-flash the right rom now!
When you start the device up what happens?
Same Problem accured for me!!!!!!!
I installeda new rom and my device didn't power on after that.
What should i do now?
afghahi said:
I installeda new rom and my device didn't power on after that.
What should i do now?
Click to expand...
Click to collapse
Nobody here is providing any details so everything is going to be just a guess. If either of these phones were a G4 and you flashed a rom that tried to update the IPL/SPL then its very likely you have bricked your device. But again, with no information about what rom you were trying to flash, what your IPL/SPL were beforehand, or details about what it means that it won't turn on, everything is just a guess...
Bricked Kjam
its comletely dead.....i had disconnected the battery for a couple of days then connected it but it wont start....i checked the battery using multimeter it is fully charged....neither does it power ON when connected to mains...It doesnt get detected when connected to the USB port..thats obvious since it is not powering up...so cant flash it again.. now m in a fix as to whether to spend another fortune after this sweetheart or keep it in a showcase ....
Deven
( a bricked KJam )
If nothing lights up that looks pretty terminal. :-(
Maybe you could buy a broken Wizard with a working motherboard? Alternatively maybe sell off your mostly working Wizard on this forum to raise money to buy a new device?
Sorry if you can't get it going. :-(

Bricked Hermes (SPV M3100) while flashing SPL - any help or sugestion are wellcomed

All started with trying to upgrade(rewrite) the GSM part because the Hermes had problems with phone part - when trying to call - the phone stop responding, bus the pda part sill worked.
So - I tried and tried and tried again, reading many threads about HARD SPL,Flashing radio, etc. Nothing worked..
In the end "i managed" to kill GSM - phone had "No Gsm" on boot-up.
From there i tried to downgrade SPL to 1.04 so that i try to "raw" rewrite the GSM part.
But something went terribly wrong, and while downgrading SPL, the phone suddently shutdown and never opened again.
Now i have the folowing situation: NO BOOTLOADER, no usb conectivity, nothing
This means that i cannot connect via USB whatever i try.
Is there any hope for me? or is it TOTALLY BRICKED?
Any help is apreciated!! I can even dismantle the mobile if there is any way to flash it via some kind of jtag connection...anything ...
The folks at www.imei-check.com can do the JTAG flashing. Just email them. It would be costly for you to do it yourself...
Are you saying that the phone won't turn on at all or that it does but you can't get a bootloader screen?
Have you tried taking the battery out for a while? Have you tried flashing an OEM rom and radio compatible with your device off an SD card?
All of this info is in the wiki, as are OEM roms you can flash.
Let us know how you get on.
Good luck.
WB
Try this:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
@wacky.banana: The phone is totaly dead: no bootloader, doesn't boot at all, doesn't seem to have any USB conectivity at all. Flashing from micro sd doesn't work : probably because the bootloader isn't working.
@drummer10630: i'll check with imei-chek about jtag flashing, especially the price and shiping costs.thanks
@markafreeman: I tried, but when i put the battery in, the red light goes off, not to amber . no soft or hard reset helps. not even leaving the battery out for 2 weeks - i had tried that too . thanks anyway.
Anything else I can try? - phone totaly dead, no bootloder, no usb conectivity - cannot use mtty, cannot flash from microsd
I had to get a replacement device at that point when it happened to me.
Maybe someone else know a way to get it working.
Good luck.
get onto orange
tell them you dropped the phone
and it crashed and wouldnt turn on
so you managed to hard reset it
and it crashed an ****ed up
they'll replace it
well they will send it to HTC
who just replace the handset rather than repair it
Hi dancameo2k , maybe you will not remember but plz:
I ve bought recenty an spv m3100, im effortless trying to flash the rom to an wm6 version.
Like you ive started with the hardsppl flash thing to prevent bricking it and prior to sd flashing... and im not sure if its workin...
plz can you explain in detail how did you bricked it??? thx!!!!
the rom you used to flash was an american version or european one???

HTC Imagio wont turn on

My name is carlos and im new in the forum.
This is my problem. I have an HTC Imagio. I tryied to update it but i fail because my phone wont turn on again. I dont know what can i do because I new in the htc world and I dont know how can I start.
Please heeeeeeelpppppp meeeeeeeeeeeeeeee
when yoy say "fail" what exactly happen....???
The phone wont turn on again T_T
You're not giving a very good explanation, did you attempt boot loader mode? anything else? at the present moment, you're just taking up thread space..
The boot loader mode is the hard reset??? or what is it?? The phone doenst enter on the hard reset (color screen with 3 options)
Moved as this is not ROM Development
Sorry about that, anyone know how i can fix it????
Hi i have a imagio dead. No bootloader load (someone wrote a blackstone hspl) and broke it .. the only thing when i connect on usb it is found as a qualcomm msm smthing. no drivers for this.. looked all over, xda, google. i found some jtag methods... I wrote a Intelpxa for a rw6815 with jmmflaser... but befor trying a jtag method, and/or try to sell it for components, i want to give it another try. Does enyone know how at least connect to mtty(to write wia usb the bl), or write a bl (any) wia usb?
Imagio Bricked
No USB way...
Unbrick a phone just can be made with JTAG tools... See jtagbox.com/riff-jtag-box-owners-unbrick-your-phone/shops-unbrick-bricked-phone-riff-box-owners-list
Hello everyone ... this is my first post on the forum I'm a reprimand in my assistance, a residue in Brazil and a customer trou Imagio HTC unlock the verizon and I just noticed that no longer seems to me he is the one CDMA XV6975 which blotted out and not turned over, but do not have IMEI MEID DEC and HEX as well ... riff bought a box to try and repair it could make you turn it on, no longer leaves the HTC logo and is vibrating, already tried the hard reset recovery mode and nothing continues to vibrate, not boot tried one more rom's not leave 0%. Can anyone help me with this device, because the customer does not come out of my foot.
Thanks to all.
Htc imagio bricked
hello guys, i really need help from u. i bricked my imagio this evening and right now it wont turn on so i don't know if u guys can hlp me with any software to recover it.
I will be very happy to c my imagio is breathing.
thanks for your help may God bless you all.

[Q] USB ONLY ALLOWS WP7 FLASH/no charge/no usb in bootloader

hello, guyz!
this is a full story of mine after wp7.8 by H2OWNER FLASH AND BATTERY GOT DEAD:
"HD2Owner, dear,
it's not to abuse as we know all the risks we take testing roms, just asking for your advice:
1. I did install your latest rom
2. after some time it stopped charging at all
3. the problem is the phone got unable to charge under sd android as well.
4. at the end of story battery got dead - can't load magldr.
5. managed to direct power on it via red/black cables of usb to +/-
6.but the problem still the same - I can't charge battery via phone
7. and even more - can't enable usb via bootloader (tricolor) - serial only:
- usb flasher works only with wp7 rom install;
- magldr, hspl, task29 flash via usb flasher fails with critical error 0000001;
- naturally, can't flash winmo;
- usb storage works well.
I'm completely lost what to do
h2owner, dear, I made grand research over google and xda.
can add only, that in addition I've already tried:
1. nbh of the default os flashed fine
2. pins in phone battery slot are properly aligned
3. I did try to clean both usb cable and usb port
and issue is still here - no charge under any os/no usb in bootloader/usb mass storage works fine/can flash only any wp7 build/the rest "flashes" lead to no usb connected
and what I can say is only that this is almost definitely connected to the usb power management of the phone by your wp7.8 build.
thus, that would be great if you know what to do and how to fix it. probably, reflash your wp7.8 updated with this fix?"
as for the moment I've managed to flash original wm3.14 rom via sd.
still no usb in bootloader, no charge.
don't know what to do yet.
don't even say usb is broken -
THE MAIN POINTS ARE THAT
1. I STILL CAN FLASH WP7/7.8 VIA USB FLASHER
2. I STILL CAN FLASH MAGLDR VIA USB FLASHER
3. BUT NOTHING MORE
4. AND USB MASS STORAGE WORKS AS WELL
5. UNDER WP7/7.8 STILL NO USB/NO CHARGE
the couple of thoughts to take in attention:
1. I did close zune while it's starting first time with wp7.8 by HD2OWNER under admin account
2. I did try another pc (win7, mine is w7 as well - same results, no usb)
please, post your suggestions, but remember - I CAN FLASH WP7/7.8 VIA USB FLASHER, WHICH MEANS HARDWARE IS OK.
okay, first news on the subject:
HD2Owner Today, 02:54 PM #3079
Recognized Developer - OP
Thanks Meter 1459
Posts: 1,947
Join Date: Oct 2009
Location: Neuhausen am Rheinfall
MORE INFO >
DONATE TO ME
important info related to usb2video:
usb mode is not changed back to zune/charge mode with a simple reboot.
you have to click usb2video appicon again and switch back to normal zune mode (with needed reboot).
otherwise, performance will stay choppy and device will never charge/connect to zune again.
WILL KEEP YOU UPDATED
this is going to be my personal blog alike..
okay, speaking with myself..
in order to have wp7.8 back, I need hspl and magldr..
then how to flash hspl now from spl 1.42 and without usb???
omfg.
hi dimdimdim !
this Thread & post for you only
i think must usb
try with this tool
http://forum.xda-developers.com/showthread.php?t=1090783
maybe can help you
boxmax said:
hi dimdimdim !
this Thread & post for you only
i think must usb
try with this tool
http://forum.xda-developers.com/showthread.php?t=1090783
maybe can help you
Click to expand...
Click to collapse
yes, I tried...but this is not more than interface for same magldr, hspl, recovery...method is not changed..
but thanks for suggestion!
Maybe is problem with usb drivers on your pc,try to reinstall them,tricolor screen won't recognize usb if you dont have drivers proper installed....
zexmunze said:
Maybe is problem with usb drivers on your pc,try to reinstall them,tricolor screen won't recognize usb if you dont have drivers proper installed....
Click to expand...
Click to collapse
I did try it on another pc...still no usb
This does sound like a hardware issue to me. I know you dont think it is an hardware issue, because some of the communications still work.
But the active driver determines the hardware id's that broadcasted. The drivers are mainly on OS level. Booting another OS would definitely solve problems in the problematic OS.
I think the one of the power-pins on your USB jack is broken.
The only other possibility that I can think of, but it is unlikely, is that Magldr somehow screwed up and interferes with the USB-power-management.
The Video-to-USB is unlikely the cause, because AFAIK it does not influence the power-management of the USB.
Heathcliff74
Heathcliff74 said:
This does sound like a hardware issue to me. I know you dont think it is an hardware issue, because some of the communications still work.
But the active driver determines the hardware id's that broadcasted. The drivers are mainly on OS level. Booting another OS would definitely solve problems in the problematic OS.
I think the one of the power-pins on your USB jack is broken.
The only other possibility that I can think of, but it is unlikely, is that Magldr somehow screwed up and interferes with the USB-power-management.
The Video-to-USB is unlikely the cause, because AFAIK it does not influence the power-management of the USB.
Heathcliff74
Click to expand...
Click to collapse
okay, if jack is broken, then I have only chance to send the phone to the service.
the point is that I'd like to know whether there is a way to go deeper, than OS level.
is that possible with tools, available at home? with cab for wm6.5 or nbh with drivers?
h2owner wrote it is not possible to charge the phone anymore if apply usb2video and not enable normal mode back again.
I can't say 100% I do not push usb2video once. I'd rather say I did it once and no more. and after that my battery got dead during a call.
thus, usb2video may get stuck on it's half way...
just to be sure - is there any option to apply some tool, which can go that deep into a hardcoded drivers?
if that was possible to get somehow wp7.8 back and apply usb2video again...but - no usb means no hspl..
by the way, JIC, isn't it possible to use usb2video cab on wm65?
dimdimdim said:
okay, if jack is broken, then I have only chance to send the phone to the service.
the point is that I'd like to know whether there is a way to go deeper, than OS level.
is that possible with tools, available at home? with cab for wm6.5 or nbh with drivers?
h2owner wrote it is not possible to charge the phone anymore if apply usb2video and not enable normal mode back again.
I can't say 100% I do not push usb2video once. I'd rather say I did it once and no more. and after that my battery got dead during a call.
thus, usb2video may get stuck on it's half way...
just to be sure - is there any option to apply some tool, which can go that deep into a hardcoded drivers?
if that was possible to get somehow wp7.8 back and apply usb2video again...but - no usb means no hspl..
by the way, JIC, isn't it possible to use usb2video cab on wm65?
Click to expand...
Click to collapse
Just tested for you: The phone DOES charge when USB Video Out driver is selected. I just switched back and forth and it charges always. Using HTC HD2 with exact same ROM as you used.
There are no such low level tools to look into drivers. At least, not for WP7 that I know of. But what do you expect to see? If you are booting Android, it uses Android drivers, with Android power-schemes. Completely different, but same problem. That proves for me, the problem is at hardware level. Any ROM flash or Hard Reset should always reset the USB mode/driver.
Maybe you can try to flash MagLdr on it (again). That is the only software-solution that I can think of.
Good luck,
Heathcliff74
Heathcliff74 said:
Just tested for you: The phone DOES charge when USB Video Out driver is selected. I just switched back and forth and it charges always. Using HTC HD2 with exact same ROM as you used.
There are no such low level tools to look into drivers. At least, not for WP7 that I know of. But what do you expect to see? If you are booting Android, it uses Android drivers, with Android power-schemes. Completely different, but same problem. That proves for me, the problem is at hardware level. Any ROM flash or Hard Reset should always reset the USB mode/driver.
Maybe you can try to flash MagLdr on it (again). That is the only software-solution that I can think of.
Good luck,
Heathcliff74
Click to expand...
Click to collapse
okay, this is that kind of proof I'd want to have before I send the phone for repair.
thank you, Heathcliff74.
dimdimdim said:
okay, this is that kind of proof I'd want to have before I send the phone for repair.
thank you, Heathcliff74.
Click to expand...
Click to collapse
You can try to reinstall Magldr, although I don't think it will help.
Just to be clear: Information I gave is the best of my knowledge, but it is provided "as is". I don't take responsibility of any costs that arise from using the provided information, even when that information proves to be incorrect afterwards.
That said, I hope they can fix it for you. But I guess a good repair man can easily determine if the usb jack is indeed broken.
Good luck,
Heathcliff74
Heathcliff74 said:
You can try to reinstall Magldr, although I don't think it will help.
Just to be clear: Information I gave is the best of my knowledge, but it is provided "as is". I don't take responsibility of any costs that arise from using the provided information, even when that information proves to be incorrect afterwards.
That said, I hope they can fix it for you. But I guess a good repair man can easily determine if the usb jack is indeed broken.
Good luck,
Heathcliff74
Click to expand...
Click to collapse
I did reinstall magldr when still had hspl 2.08...but now I'm on spl...
thus..happy repairing!
I did already replace usb socket half of year ago, that's why I did struggle so much for not hardware issue

Categories

Resources