CHarging your t9193 through a USB hub? - HD2 General

Who here uses a USB hub to charge their t9193? I tried this on a Belkin USB hub without success (light indicator doesn't turn on). Is there a speciic way to make it charge through a USB hub or is mine just not compatible?

Does your HD2 charge from a PC USB port properly? A lot of times, USB hubs will need a 12v DC power source to create the 5v power required for USB devices. (Wall wart to the mini circular plug end found on laptops, etc) If your hub doesn't have that input, I'd find one that does. I bet that's your issue.

On a good powered usb hub maybe, but it will still
be less power than the wall charger and will not charge your battery as well.

JuBond said:
Does your HD2 charge from a PC USB port properly? A lot of times, USB hubs will need a 12v DC power source to create the 5v power required for USB devices. (Wall wart to the mini circular plug end found on laptops, etc) If your hub doesn't have that input, I'd find one that does. I bet that's your issue.
Click to expand...
Click to collapse
My USB hub is powered by an AC adapter to the wall. I'm thinking it may be the voltage that doesn't work w/ the hd2 then..

So my USB Hub says
input 100 - 240V~0.8A 47-63Hz
output 5V 2.6A

That is probably spread over all the ports on the hub.
What else is plugged into the hub? Un-plug them and try to charge. Many hubs will say that and not come with the extra power supply. It is extra. Does yours have the power supply?

Yes, it has a physical power supply and when I tried it, nothing else was plugged in except the power supply to wall.

Related

Silly Charging Question

So this may be a silly question, but I've just received the T-Mobile MDA (HTC Wizard) second-hand and without a charger.
The Mini USB port on the bottom allows ActiveSync and charging from my notebook's USB port, but when I try to charge using an AC-to-USB adapter it doesn't work... I've tried two different Motorola phone chargers and a generic one that came with my Jawbone that has a USB female connector on the adapter and you supply your own USB cable. I've used the same cable I was using when attaching to the PC, but no luck.
Interestingly enough, I did get it to charge with the same USB cable once at an airport by plugging it into the Southwest Airlines chairs with the USB power plugs...
So does anyone know? Does this phone require a special sort of charger?
you need a charger that is rated 1.0Amps.
usb is normally 500mAmps, not enough to charge your phone.

[Q] Charging TAB from a PC USB or USB Hub

I setup a self-powered USB2.0 hub which has a 2.5AMP power adapter. I used a dual male (split) to single female USB cable and plugged the TAB USB cable into that.
This same dual cable & hub works fine to power an external USB hard-drive which won't work with just a single cable for power. I would think with 2+ AMPS it should charge the TAB "normally" (with no "x" on the battery indicator) but it does not, the "x" remains. All other devices have been removed from the hub.
Anyone else been able to get a normal charge off a PC or USB hub with a split cable? It's such a pain to have to put the TAB on the wall charger then switch it back to the PC.
when the screen is off the device charges, despite what the battery display says.
tca120 said:
when the screen is off the device charges, despite what the battery display says.
Click to expand...
Click to collapse
Correction, it trickle charges. Very slowly.
LordLugard said:
Correction, it trickle charges. Very slowly.
Click to expand...
Click to collapse
I understand that but I was under the obviously incorrect impression that if you used a double male USB to single female USB cable you would get a normal charge since there is more power available. Is the charge rate dependent on the TAB seeing power on a specific pin of the cable telling it that a charger is connected and not a cable to the PC? I'm connected to a self-powered hub with a big 2.5amp power supply and nothing else connected to it.

How to attach usb powered hub to android stick? Which port

I have an andrid. Stick mx2 imito and I have a powered USB hub but I can't configure how I am meant to to get it to read from the hub. I have 2 ports on the stick, one full sized usb and one mini usb .
And In terms of devices I have my keyboard I want to add
1 external usb hard drive
And if I can get it to work a USB wifi dongle
Huh!
Since there is only one full sized USB port, I would think that is the solution. That's how it runs on mine anyway. Connect all your devices to the powered hub. Should be straight forward
So I would need a usb cable male to make? To connect to the hub. Do they exist ? I will try find the cable .
i cantget it to work
so the large usb port. i need a cable from that to connect to the hub? usb port
but i dont have a usb port with the same end? male to male etc
Get a USB powered hib
wakkaday said:
i cantget it to work
so the large usb port. i need a cable from that to connect to the hub? usb port
but i dont have a usb port with the same end? male to male etc
Click to expand...
Click to collapse
The hub will come with one male USB to connect to the stick.
http://gadgets.softpedia.com/images/news/How-to-Charge-your-USB-Devices-Quick-and-Easy-4.jpg
Make sure to get a powered hub so that all the devices can be supported properly.
gsurath said:
The hub will come with one male USB to connect to the stick.
http://gadgets.softpedia.com/images/news/How-to-Charge-your-USB-Devices-Quick-and-Easy-4.jpg
Make sure to get a powered hub so that all the devices can be supported properly.
Click to expand...
Click to collapse
this was an old hub i had, i dont have that wire. its a mini usb to full usb type connection isn't it?
Plenty of such options available
Here is another on ebay. Just search for powered USB hub and choose one
http://www.ebay.com/itm/10-PORT-USB-2-0-EXTERNAL-HUB-W-POWER-ADAPTER-FOR-PC-MAC-WITH-cable-SILVER-/370772094009?pt=US_USB_Cables_Hubs_Adapters&hash=item5653bd2c39
gsurath said:
Here is another on ebay. Just search for powered USB hub and choose one
http://www.ebay.com/itm/10-PORT-USB-2-0-EXTERNAL-HUB-W-POWER-ADAPTER-FOR-PC-MAC-WITH-cable-SILVER-/370772094009?pt=US_USB_Cables_Hubs_Adapters&hash=item5653bd2c39
Click to expand...
Click to collapse
ok great, so the port next to the power socket, is the cable i need to attach to and from the imito android stick? so that will be the main one and any other usb devices can go on the hub.
m confused on where i need to connect from on the android stick. which has 1 full sized usb, 1 mini usb otg socket and 1 mini usb (power)
It should also be possible to modify a USB hub to back feed power to the HDMI stick.
You would then power the hub with a sufficiently large USB power supply to power both the stick and all of the USB devices. In most cases, a single 2.1 Amp USB "wall wart" would work to power everything, unless you are really running something outrageous.
My NX003 (Same as MX1) can be powered from either the dedicated USB power jack, or the MicroUSB (OTG) connector.
So to build something like this, here is what I would do:
1. Obtain a USB hub I was willing to modify (destroy, as far as any other use is concerned)
2. Disassemble it.
3. Remove the input (Host) cable or connector.
4. Attach a short cable with a MicroUSB plug. Connect all 4 wires correctly.
5. Find "The diode" - Buy "The diode" I mean the one that that allows USB power to flow from the host to the peripherals when used in non-powered mode, but prevents power from flowing upstream to the host when an external power supply is used. (see referenced link).
6. Remove this diode, and replace it with a wire, jumper, or solder bridge.
7. Ensure all power circuity in the hub can handle 2 amps. Add solder to traces, or add jumper wire if needed to beef up current capability.
8. Reassemble, and clearly mark so that this hub is never used with anything else.
If the HDMI stick were powered via a coaxial connection, but is still powered by 5 Volts, I'd add a lead and coaxial plug off of the +5 in the hub. you'll have 2 wires, but it will still work. (Watch polarity.)
I have done this successfully for a prior, similar project. Reference Here: (Scroll to section about power.)
http://linuxslate.com/N770DockingStation.html
So why don't I actually do this to power my NX003? I did it an easier way. I bought a Tronsmart Prometheus. It has 3 full USB ports built-in.
-
Linuxslate said:
It should also be possible to modify a USB hub to back feed power to the HDMI stick.
You would then power the hub with a sufficiently large USB power supply to power both the stick and all of the USB devices. In most cases, a single 2.1 Amp USB "wall wart" would work to power everything, unless you are really running something outrageous.
My NX003 (Same as MX1) can be powered from either the dedicated USB power jack, or the MicroUSB (OTG) connector.
So to build something like this, here is what I would do:
1. Obtain a USB hub I was willing to modify (destroy, as far as any other use is concerned)
2. Disassemble it.
3. Remove the input (Host) cable or connector.
4. Attach a short cable with a MicroUSB plug. Connect all 4 wires correctly.
5. Find "The diode" - Buy "The diode" I mean the one that that allows USB power to flow from the host to the peripherals when used in non-powered mode, but prevents power from flowing upstream to the host when an external power supply is used. (see referenced link).
6. Remove this diode, and replace it with a wire, jumper, or solder bridge.
7. Ensure all power circuity in the hub can handle 2 amps. Add solder to traces, or add jumper wire if needed to beef up current capability.
8. Reassemble, and clearly mark so that this hub is never used with anything else.
If the HDMI stick were powered via a coaxial connection, but is still powered by 5 Volts, I'd add a lead and coaxial plug off of the +5 in the hub. you'll have 2 wires, but it will still work. (Watch polarity.)
I have done this successfully for a prior, similar project. Reference Here: (Scroll to section about power.)
http://linuxslate.com/N770DockingStation.html
So why don't I actually do this to power my NX003? I did it an easier way. I bought a Tronsmart Prometheus. It has 3 full USB ports built-in.
-
Click to expand...
Click to collapse
Thank you for the informatiom, but its a bit too technical for what i want... but i appreciate you efforts in writing this.
my stick can also power via both usb ports (mini) i have connected the cable from the stick to the hub which has been powered to the mains and it works, but the problem i have is when i put another usb device in the hub, it doesnt detect it e.g. keyboard wireless and i don't think the device has enough power to run my usb 2.0 portable harddrive (not main powered) - how can i get this to work? i have tried connecting this directly to the stick, but it just makes a beep sound. im guessing its lack of power... and i was hoping a hub would help.
my hub is powered 3.5 or 4 watts i believe...
Strange
Wakkaday,
This is very strange. On my MK802III I connect the powered USB hub (4 ports) to the full USB port.
I connect my bluetooth keyboard, 1 TB HDD and USB ethernet to the hub.
I power my Android stick using the 4rth port in the USB hub.
If I want USB audio, I replace the Ethernet/HDD with a USB audio peripheral.
All my peripherals work right out of the box. The only thing I am considering now is to have a separate power supply to the Android stick so that I can use all 4 ports on my hub.
It seems your device is not supporting the peripherals? Are the working when you connect directly?
gsurath said:
Wakkaday,
This is very strange. On my MK802III I connect the powered USB hub (4 ports) to the full USB port.
I connect my bluetooth keyboard, 1 TB HDD and USB ethernet to the hub.
I power my Android stick using the 4rth port in the USB hub.
If I want USB audio, I replace the Ethernet/HDD with a USB audio peripheral.
All my peripherals work right out of the box. The only thing I am considering now is to have a separate power supply to the Android stick so that I can use all 4 ports on my hub.
It seems your device is not supporting the peripherals? Are the working when you connect directly?
Click to expand...
Click to collapse
I'm also trying to use a powered 4 port usb hub with my android stick, but it doesnot recognises the hub. Do i need to have any usb host drivers or change any setting to get it work? My stick is on Android ICS.. Thanks in advance

[Q] Does the USB 3.0 cable charge faster via AC?

I suspect I know the answer to this, but I just wanted to get confirmation.
I was originally led to believe that the Galaxy S5's included USB 3.0 charging cable allows faster charging than a USB 2.0 cable. Upon thinking it over, the 3.0 cable should really only provide faster charging compared to USB 2.0, and only when plugged into a USB 3.0 computer port.
When using the same USB 3.0 cable via an AC wall adapter, the power output of the wall adapter should be the only thing that really determines the charging speed: Fast charging with a 2-amp wall adapter, slower charging with a 1-amp adapter; whether the cable is USB 2.0 or 3.0 should not matter.
Am I correct here?
The USB 3 cable provides only extra data lanes no extra charging speed. The AC charger will charge at 2amp and on PC you are likely to get not much better than 450mili Amp.

OTG Cable Mod to block power output to peripherals

First, my apologies if this isn't the proper place for this thread. Please point me in the right direction.
I have an in-dash Nexus 7 solution using an OTG cable and a powered USB hub. My issue is the damn USB devices connected to the hub suck the life out of the N7 when power is turned off to the hub and OTG connected charger. I attempted to mitigate this by splicing a 1N4001 diode on the power side of the OTG cable but not luck. The N7 charges properly but the USB devices still show power when the power is turned off to the USB hub.
Any help would be greatly appreciated.

Categories

Resources