Database Users

Dead cruise?

Hi
I seemed to have killed my phone tonight. Originally I flashed it with HardSPL then udk Vega firmware. It seemed to work OK but TomTom wouldn't work so I tried to flash it with something else. Now it boots up with the udk Polaris flash screen and then it dies. The screen is vagually there but there is no USB connection (either through Activesync or the firmware software). The bootloader screen is showing:
POLA100
SPL-1.28.0000
CPLD-2
I've tried lots of different firmwares, the original will not install (1.25.405.1) the error is 294 INVALID VENDOR ID
Has anyone any idea how I can fix my 1 month old phone please?
Kevin

first of all,
it looks like you haven't succesfully installed hardspl
if i remember, you shold install the original rom by manualy going into bootloader (camera+reset).
After that, try and install hardspl again.
hope this helps

My phone has died to. I used it today and sudently I can not unlock it. It want either hard reset or manualy go into bootloader. When it rings, I can answer and talk, but tapping the screen do not work. I am using the Glass rom, and have used a lot of different rom`s, and it has worked perfekt all the time. To enter bootloader (camera+reset)? or (on+camera+reset)? Any tips to unlock so i can install a new rom?

camera + reset = bootloader
reflash

All sorted now, I downloaded and applied the original Australian ROM and it worked a treat. I've now properly installed HardSPL and I'm playing around with all the different ROMS

kevinbloomfield said:
All sorted now, I downloaded and applied the original Australian ROM and it worked a treat. I've now properly installed HardSPL and I'm playing around with all the different ROMS
Click to expand...
Click to collapse
Where did you get this original Aus ROM? can you post a link?

Where did you get this original Aus ROM? can you post a link?
http://forum.xda-developers.com/showthread.php?t=381600

kevinbloomfield said:
All sorted now, I downloaded and applied the original Australian ROM and it worked a treat. I've now properly installed HardSPL and I'm playing around with all the different ROMS
Click to expand...
Click to collapse
Just amazing.... My device was considered dead as well till I try and updated with the Aus original ROM! And now I'm back to business!!!!!
Thank you all my friends!!!
Direct link to the ROM:
http://www.asia.htc.com/download/RU...5.65.30.04_1.58.21.23_polaris_murata_Ship.exe

Original SPL?
Is here any chance to load original SPL. To pola100. THX

eyeless1978 said:
Is here any chance to load original SPL. To pola100. THX
Click to expand...
Click to collapse
Pleased refer this post. Install back hardspl and don't replug, wait until end session. flash back with original SPL.

Restore original SPL without screen input

Hi!
Unfortunatly i've to send by to assistance my Polaris as the touch screen don't work anymore
I've restored the original rom but now i've to restore also the original SPL.
While i'm running the ROMUpdateUtility.exe after few seconds i need to confirm that i want to run the EnterbootLoader.exe file.. but i can't do it as my screen is not working! There is a way to bypass this step to give the confirmation by default?

Ok, i've solved the issue clicking randomly around the screen
I've installed the SPL 1.25 with the Official WM6.1.. it's ok?

I think the 6.1 ROM comes with spl 1.28

deechte said:
I think the 6.1 ROM comes with spl 1.28
Click to expand...
Click to collapse
No, it comes with 3.13

-snip-
i got it wrong.. sorry..

Cannot uninstall HSPL after installing 1.66 wwe rom

My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.

mon_money said:
My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.
Click to expand...
Click to collapse
You must use a vodafone stock ROM then - the 1.66 HTC ROM flashes the stock SPL
which does not fit your CID, therefore you get the triangle.

thx for replying.
I had stock rom 1.48 before and then i installed HSPL so that i can install Stock 1.66 wwe rom into my hd2. It was a successful action. Rom installed and worked correctly without any problem.
But problem arise when I tried to uninstall the HSPL to original spl. I renamed the 1.66 rom .nbh file to LEOIMG.nbh and converted the card format into fat32 also.
when i inserted the card into hd2 and turned it on whilst pressing down volume button. its started into boot loader program and den asked me to press power button to start the process.
And then it ended with an error.. 00028002 NOT ALLOW something like that. which is for Invalid vendor ID..
Please help..
how to return to original spl with the latest 1.66 wwe rom.
thx in advance..
tictac0566 said:
You must use a vodafone stock ROM then - the 1.66 HTC ROM flashes the stock SPL
which does not fit your CID, therefore you get the triangle.
Click to expand...
Click to collapse

don't think you can, HSPL has to stay on...could be wrong though...
why do you want to take it off?

mon_money said:
thx for replying.
I had stock rom 1.48 before and then i installed HSPL so that i can install Stock 1.66 wwe rom into my hd2. It was a successful action. Rom installed and worked correctly without any problem.
But problem arise when I tried to uninstall the HSPL to original spl. I renamed the 1.66 rom .nbh file to LEOIMG.nbh and converted the card format into fat32 also.
when i inserted the card into hd2 and turned it on whilst pressing down volume button. its started into boot loader program and den asked me to press power button to start the process.
And then it ended with an error.. 02800 something like that. which is for Invalid vendor ID..
Please help..
how to return to original spl with the latest 1.66 wwe rom.
thx in advance..
Click to expand...
Click to collapse
Actually, you did everything correctly... except that you should use the stock ROM for your device, which is vodafone branded, isn´t it?
BTW, did you check the SPL version already? Because it might be already back to stock SPL, but then, you won´t be able to flash an original HTC ROM.
Being back at stock SPL (with vodafone CID) and trying to flash/launch an official HTC ROM on the branded device results in what you write!

Hmm.. is there any harm if i don't remove HSPL??? as m still trying to make my HD2 working..
error coming is 00028002 NOT ALLOW
EddyOS said:
don't think you can, HSPL has to stay on...could be wrong though...
why do you want to take it off?
Click to expand...
Click to collapse

mon_money said:
Hmm.. is there any harm if i don't remove HSPL??? as m still trying to make my HD2 working..
error coming is 00028002 NOT ALLOW
Click to expand...
Click to collapse
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.

BIG thank you .. it is working now with the stock 1.43 rom.. and yes u are right.. it was showing me again 1.42 spl after uninstalling the HSPL.
u saved my hd2.. thx once again for ur great help..
tictac0566 said:
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.
Click to expand...
Click to collapse

tictac0566 said:
Get the original 1.43 vodafone UK ROM from here, and repeat what you did.
Follow the first link, select 1.43, then obviously the vodafone ROM.
EDIT PS:
In case you want to keep the stock SPL, but upgrade to the 1.66 HTC ROM, you must do this using SSPL (search for this here in the forum).
As of today, there is no other way of getting the stock SPL back than flashing your original ROM.
Click to expand...
Click to collapse
Hi
Thanks for the link, however the 1.43 ROM is corrupt, I have tried downloading several times. I try to extra the RUU_Signed.nbh with winrar but it fails, the 1.66 and 1.72 Vodafone ROMs extract fine.
Basically I am trying to restore a Vodafone HD2 to stock ROM+SPL, reason being the phone they sent on an insurance replacement is rubbish e.g. the touchscreen isn't responsive. I tried changing to a custom ROM also Vodafone 1.66 and 1.72 to see if the problem would be fixed but it didn't help.
Now I just need to send the phone back for another replacement.
Does anyone have an alternative link for this 1.43 ROM?

I am having a similar issue.
I am trying remove HSPL, I have copied the .nbh file over to the SD already formatted as FAT 32 - I'm using my original ROM.
(RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Shp )
Also tried with ( RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship )
When I start with volume down pressed, I get a message saying " Upgrade ROM code error please try again " then the multi coloured screen with SPL-1.42.0000 XE.
Please help, I fear I have broken my phone ...

chrisukhd2 said:
(RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Shp )
Also tried with ( RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship )
Click to expand...
Click to collapse
Then your phone is probably provider rom locked.
SPL-1.42.0000 XE.
Click to expand...
Click to collapse
HSPL is already removed, which is why the WWE roms don't work. You need to find your provider released rom, or (far easier) run hspl2, choose 1.42.hspl, flash either of teh roms you mentioned above by USB, run hspl2 again, choose 1.42.0000 and done.

samsamuel
Thanks for the reply.
I can't use HSPL2 as the phone doesn't sink to my PC as it's stuck on the tri colour screen. Unless there is a way of doing this from the memory card.
I'm pretty sure my stock ROM was 1.43, which I have downloaded but can't re flash?.
I guess I need to download a 1.42 O2 ROM from somewhere?

chrisukhd2 said:
samsamuel
Thanks for the reply.
I can't use HSPL2 as the phone doesn't sink to my PC as it's stuck on the tri colour screen. Unless there is a way of doing this from the memory card.
I'm pretty sure my stock ROM was 1.43, which I have downloaded but can't re flash?.
I guess I need to download a 1.42 O2 ROM from somewhere?
Click to expand...
Click to collapse
No need to sync to pc. In bootloader, connect usb cable - when USB shows on the screen then run HSPL2

ClydeB1 said:
No need to sync to pc. In bootloader, connect usb cable - when USB shows on the screen then run HSPL2
Click to expand...
Click to collapse
pre - and indeed - cisely

OK this is using the 1.48 ROM
Used HSPL2 and hacked to 1.42.hspl, pressed power to start update image, and the ROM loaded but then goes back to the tri colour screen again. So I ran flashed through USB 1.48 ROM and got " Invalid Vendor ID " ?
I tried HSPL2 again to hack to 1.42.0000 and then re-flash through USB and got " invalid vendor ID again "
I even tried with HSPL I had before and the same result.
Argghhhhhh
What can I be doing wrong here ?

Working now
I downloaded the latest O2 ROM 1.72.0 etc and it's working now.
Thanks again guys, you helped me a lot
Once more thing my phone now say's it has SPL-1.66 - I guess when unlocking using HSPL2, I now need to choose 1.66.000?

mon_money said:
My hd2 bricks after i tried uninstalling hspl with the help of stock rru_signed.nbh file. it is not working now. just a traingle with ! this coming.
any help.. hd2 i have is a vodafone uk stock rom.
Click to expand...
Click to collapse
1. download stock ROM
2. unpack/unzip and place ruu_signed.nbh and ROMUpdateUtility in sd card
3. make sure you have >50% battery life
4. with the device turned off, put sd card in
5. enter boot loader, device will automatically detect ROM file in sd card and
then will install this, it will install stock spl as well so hspl will be removed

chrisukhd2 said:
OK this is using the 1.48 ROM
Used HSPL2 and hacked to 1.42.hspl, pressed power to start update image, and the ROM loaded but then goes back to the tri colour screen again. So I ran flashed through USB 1.48 ROM and got " Invalid Vendor ID " ?
Click to expand...
Click to collapse
sounds like you tried to flash over sd card, which as any fule kno first thing it does is resets the spl, so hspl is no longer installed so the rest of the flash fails.
I tried HSPL2 again to hack to 1.42.0000 and then re-flash through USB and got " invalid vendor ID again "
Click to expand...
Click to collapse
because its .0000
I even tried with HSPL I had before and the same result.
Argghhhhhh
Click to expand...
Click to collapse
used sd card again eh?
1 - boot the phone to bootloader. (Three coloured screen)
2 - run hspl2, choose whatever spl you like SO LONG AS it ends HSPL.
3 - when the phone reboots, keep volume down pressed to re enter bootloader
4 - run your rom flash over USB
5 - phone should now boot normally.
6 - if you now want to remove hspl again, re run HSPL2 and choose the spl you want, ENDING IN .0000

samsamuel
Yes Doh - I was flashing from SD and then trying to flash through USB. It all makes sense now. I got around it though by using the new O2 ROM that's just been released so I didn't need to unlock to bring my phone back to life.
Anyway it's all working fine now with the stock 1.72 O2 ROM, just flashed with HSPL2 and re-installed the Energy ROM.
Thanks again for all the help.

ahh good.
Its a good idea if you flash fairly regularly to do your flashing from bootloader, that way you are visually aware of your spl at every step. just get used to holding vol down as it reboots and you can do the whole thing, hspl, rom, radio, without ever having to pull the battery. just keep booting to tri colour till its done.

HD2 stuck at white bootscreen

Hello,
I bought HD2 just yesterday, probably as every member of xda, i tried flashing it. No problem, i tried several ROMs and as far as i remember - after flash it got stuck at white bootscreen with green HTC (i found several threads dealing with this problem, but most of the people had written there ROM, RADIO, .. in the left corner - I dont have this written) So I tried to flash the phone from the SD with stock rom, nothing has changed, I tried taking out the sd & sim card. I tried hardresetting device few times and I got no more ideas.
Do you have any ideas?
Thanks in advance!!!
Filip
Edit 1: In the PDA Phone Rom update utility I cannot see the old version of ROM & Radio..
Edit 2: For now I have HSPL in the phone.

sounds like a missmatched rom and radio. once they are both flashed correctly it will boot. (example, a rom based on 2.10 rom will require a radio of around 2.06 or better to boot.)
edit - just seen you flashed with a stock rom from sd card, can you boot to bootloader? (press and hold vol down, tap power on)
dont worry about
In the PDA Phone Rom update utility I cannot see the old version of ROM & Radio..
Click to expand...
Click to collapse
for now

Felipe404 said:
Hello,
I bought HD2 just yesterday, probably as every member of xda, i tried flashing it. No problem, i tried several ROMs and as far as i remember - after flash it got stuck at white bootscreen with green HTC ...
Edit 1: In the PDA Phone Rom update utility I cannot see the old version of ROM & Radio..
Click to expand...
Click to collapse
I had exactly the same problem several days ago. After exchanging several ROMs, I got stuck at very first white screen with a green banner, but before it even showed the ROM and radio versions on it. And it happen after the ROM flush finished successfully. I also tried to hard reset it a couple of times.
But after that I used a gold card with 1.61 WWE ROM on it that I still have from the time when the HSPL wasn't developed yet.
During the flash from the gold card it waited at first and shown a some kind of error or warning grey exclamation sigh in a triangle, but just for a split second. After that it returned to continue flushing. I think it took twice as long as it should be, but as it finished, I was able to boot, hard reset and re-flash to the stock ROM 1.66 WWE, the usual way through the USB cable.

samsamuel: I can get with no problem to bootloader, could you send me exact link of the rom and radio that work together? And how come, that everytime I connect the phone to charger, it starts up?
mikiort: I havent ever used goldcard, havent ever heard of it better to say..
thanks for your help, guys, really appreciate it!!!

Since you have HSPL stil on your phone
(SPL 1.42.HSPL and not 1.42.0000) you are happy. Flash a stock rom from USB, lets say a 1.66 wwe rom, and if it still wont boot, go to teh radio roms thread, pick a low radio, (the 1.61 for instance) flash that, and you should have a working phone.

yeah, right now im flashin 1.66 WWE but it stopped and 99%... waaa im gettin nervous ok i will try and let you know

Ok, flashed 1.66 WWE but nothing has changed, im about to flash radio.

Flashed Radio 1.61 "Leo_RADIO_15.30.50.07U_2.06.51.07.nbh.7z" and still nothing... Oh!!! do you have any other ideas? Or should i again try to flash from SD official ROM?

Felipe404 said:
Flashed Radio 1.61 "Leo_RADIO_15.30.50.07U_2.06.51.07.nbh.7z" and still nothing... Oh!!! do you have any other ideas? Or should i again try to flash from SD official ROM?
Click to expand...
Click to collapse
hmm, sorry to hear that. i'd maybe consider flashing stock from sd card, but you need to be sure you have teh correct stock rom for your phone provider and region.
Be warned, this will remove HSPL, if you do not have the correct stock rom, it wont work.

Yea, i did that once already with 1.48 WWE Eastern Europe, it worked (it didnt show the triangle sign) but it didnt help, now im trying to flash 1.43 but im not expecting anything good

Done, nothing helps ... Now i have SPL 1.42000 so i can get the HSPL but as far as it doesnt help i dont know what to do...

Felipe404 said:
Done, nothing helps ... Now i have SPL 1.42000 so i can get the HSPL but as far as it doesnt help i dont know what to do...
Click to expand...
Click to collapse
Ok, if you have 1.42.0000 you need to redo the hspl flash. Once the spl is 1.42.hspl you can then flash to the rom of your choice. Which rom were you trying?
Many of the new roms require you to flash to a new radio at least 2.06 and most recently to 2.08 PRIOR to flashing the rom and if you don't the rom does not boot up and gets stuck on the white HTC screen.

really noob question, but anyways... do you firstly flash the rom and than the radio?
and to those ROMs.. i tried duffys, energy and one more i cant remember right now.. Im trying to HSPL and than flash from Vista computer, not XP...

Felipe404 said:
really noob question, but anyways... do you firstly flash the rom and than the radio?
and to those ROMs.. i tried duffys, energy and one more i cant remember right now.. Im trying to HSPL and than flash from Vista computer, not XP...
Click to expand...
Click to collapse
For these newer roms you need to flash the radio first and then the rom, otherwise the rom doesn't boot up and gets stuck on the white screen.

If you are flashing a newer ROM based on the new TMOUS ROM I would flash the 2.08.50.08.03 Radio, then the ROM. Make sure you have HSPL 1.42 first.

Ok, I do have SPL-1.42.HSPL CotullaHSPL there... now if possible tell me the "for sure" working combination... Btw, i remember how did it happen, i flashed dutty's rom and wifi was not working (option in communications couldnt be turned on/off was grey) and so i tried to flash there other rom.. and it got into problems..

Felipe404 said:
(option in communications couldnt be turned on/off was grey)
Click to expand...
Click to collapse
thats usually means you have the phone on usb connected to the computer.

Felipe404 said:
Ok, I do have SPL-1.42.HSPL CotullaHSPL there... now if possible tell me the "for sure" working combination... Btw, i remember how did it happen, i flashed dutty's rom and wifi was not working (option in communications couldnt be turned on/off was grey) and so i tried to flash there other rom.. and it got into problems..
Click to expand...
Click to collapse
I'm currently using the latest NRG rom (link in my signature) with the 2.08.50.08 radio and that works. Just as I said, flash the radio first and then the rom. The Dutty rom should also work the same way though so the choice is still yours.

OK so here i come, i flashed there firstly the radio Leo_RADIO_15.34.50.07U_2.08.50.05, then Dutty's ROM Duttys Leo HG V1 5.2.21892 but nothing has changed.. I think the device is ready to be sent to HTC, what do you guys think?

Felipe404 said:
OK so here i come, i flashed there firstly the radio Leo_RADIO_15.34.50.07U_2.08.50.05, then Dutty's ROM Duttys Leo HG V1 5.2.21892 but nothing has changed.. I think the device is ready to be sent to HTC, what do you guys think?
Click to expand...
Click to collapse
What did you do to flash the radio? Please explain how you did it.

[ROM]YardieROM v3(RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a _22 .51.50)Unlocked

Here is the new RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a_22 .51.50, unlocked and ready to go:
http://www.4shared.com/file/LgeeWQfG/Mozart_YardieROM_v3_501_7720.html
Changelog:
Developer Unlocked,max apps and prevent relock.
Custclear.provxml added to /windows
HTC theme replaced with grey theme
Alert tones 1-3 replaced with "you got Mail"etc
Internet explorer first run to google.
Added XBMods certs for update cabs.
SPL removed.
Instructions-
Be aware of XSPL issue with Mozart 4.XX & 5.XXroms, if required flash back to a NoDo rom before flashing XSPL.
1.Enter bootloader(Power on& vol-)
2.Flash RSPL(downgrade to NoDo if on 4.xx or 5.xx SPL)
3.Flash YardieROM using Rom Update Utility.
Respects out to Cotulla&DFT,bepe,ansar,XBMod,Football,Marvin_S,DaG,AnDim ,Ted973,Heathcliff74,airextreme&ceesheim for all the work they have put into WP7 development and creating the tools for us to play with.

--Reserved--

thank, after flashed will change the spl version? or stay with old hspl?

hengmy said:
thank, after flashed will change the spl version? or stay with old hspl?
Click to expand...
Click to collapse
It will remain with your original spl

Add Lang.
Is this rom able to work with RegistryEditor 1.2.0.0?
But it seems unable to save string I added.
thx
ps. I've managed to add Chinese to this ROM.

kevin3688 said:
Is this rom able to work with RegistryEditor 1.2.0.0?
I'm trying to add Chinese with RegistryEditor 1.2.0.0.
But it seems unable to save string I added.
thx
Click to expand...
Click to collapse
RUU_Mozart_S_HTC_Europe_5.01.401.04_5.71.09.02a_22 .51.50
Europe region... it means there is no chinese language pack in it.

The Registry Program 1.2.0 works
I need original theme, the new theme and Alert tones is not good.

I tried to flash your Rom it struck at 7%, luckily it didn't change my bootloader, back to Ansar's, thanks anyways.

the charging sound had been changed to "you got a voice message" not a big issue but.......

yardie.spike said:
It will remain with your original spl
Click to expand...
Click to collapse
Not good ... Is it reverssible ?

Caramel said:
Not good ... Is it reverssible ?
Click to expand...
Click to collapse
Whats not good?.....it means you can use XSPL and flash the latest roms rather than brick your Mozart.

Cheers Yardie boy
Loading it now

Be carrefull !!!
Begin flash with HSPL 1.32
Freeze while flashing
Reboot in bootloader to restart the flash.
Unable to flash again, Why ?
This rom put my Mozart in SPL 5.1, unable to go back in HSPL.

Caramel said:
Be carrefull !!!
Begin flash with HSPL 1.32
Freeze while flashing
Reboot in bootloader to restart the flash.
Unable to flash again, Why ?
This rom put my Mozart in SPL 5.1, unable to go back in HSPL.
Click to expand...
Click to collapse
No issue with HSPL 1.32 for me...no change in SPL either, what did you do different?
You could alwasy load an OSPL then put RSPL/HSPL on again.
The only little snag I noticed was connection set-up kept launching every reboot, which was resolved by deleting it...