Align touchscreen after replacing - Touch Diamond2, Pure General

The touchscreen of my HTC Diamond Touch 2 had a "Newton Rings" problem. So i decided to replace it. Found a new touchscreen on E-bay and replaced it in a hour or so.
But after rebooting the alignment of the touchscreen is not correct.
After trying "Remote screen Aligment" form Code factory, the screen aligment program in my HTC keeps on looping.
Even tried to use "Mymobiler", so i could remotely use my HTC from a pc and start the screen alignment program, but that also keep looping.
Also used "CeRegistryEditor" to change the registry of my HTC from a pc, to change the calibration Data of m touchscreen. But i dont have the correct data code. Does someone got the correct code for me?
You can find it here:
HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH:CalibrationData
This is my code: (and not working correctly)
511,558 182,889 187,217 847,216 850,892

Here you go man.
I exported the whole Touch registry just in case.

Related

XDA II Screen malfunction

I tried using the XDA II today and the screen touch pad does not respond at all. The up down rocker wouldcycle through the today items and the hardware buttons worked. I tried a soft and then hard reset. Now I can not get past the set up screen where it says taps the screen to set up your device.
Any ideas?
There are two problems that i can think now.
Firstly, it due to screen protector. If you change a new one, try remove it.
Because screen protector is not suitable or incorrect place.
Secondly, it due to some program that you've been installed.
In my case ,I found problem with Calligrapher7.4. After I install,my screen is totally locked but Hardware button still work.
The way to resolve is by uninstall program via activesync. Just put your device to cradle wait until sync is completed ,then click add/remove program and remove your suspected software that cause your problem.
Hope you can solve this problem.

Stuck at align screen

Hello
i've got en elf but it is stuck at the align screen.
i searched the forum for many day's and i found out that the digitizer probably is broken.
So i bought an new one an installed it with this manual
http://forum.xda-developers.com/showthread.php?t=407323
great manual by the way
I also installed a new housing
I installed one of the new roms
But it is still stuck on the align screen$
I have a constant loop
first middle cross, then the 4 corners and then back to the middle
i installed a program to override the align screen and then the i can use the phone but when i tap the touch screen it is not the place i tapped that opens because it is not aligned
What can i do because i am all out of answers
ps there is no warrenty anymore
Greetz Hatchy
it could be the touchscreen
LCD and touchscreen are not the same
some models heve them separated,some not
as i could see elf has
touchscreen pic1
LCD pic2
so try replacing the touchscreen they are few dollars on ebay
Or if you want, you can have somebody cook a ROM for you that bypasses the screen alignment part.
kareem9nba said:
Or if you want, you can have somebody cook a ROM for you that bypasses the screen alignment part.
Click to expand...
Click to collapse
i doubt it's the software,because he said he tried some roms
and bypassing screen align can make phone unuseable,so....
farukb said:
i doubt it's the software,because he said he tried some roms
and bypassing screen align can make phone unuseable,so....
Click to expand...
Click to collapse
Yea, but even though, he can still use the phone without the touch screen before he gets it replaced.
kareem9nba said:
Yea, but even though, he can still use the phone without the touch screen before he gets it replaced.
Click to expand...
Click to collapse
well if it was artemis...he could (arte has a mouse pointer)
but elf lacks the buttons,so using it without touch will be tricky
Hello
i replaced the touch screen because the old one had the same problems
but the new has the same problem
hatchy said:
Hello
i've got en elf but it is stuck at the align screen.
i searched the forum for many day's and i found out that the digitizer probably is broken.
So i bought an new one an installed it with this manual
http://forum.xda-developers.com/showthread.php?t=407323
great manual by the way
I also installed a new housing
I installed one of the new roms
But it is still stuck on the align screen$
I have a constant loop
first middle cross, then the 4 corners and then back to the middle
i installed a program to override the align screen and then the i can use the phone but when i tap the touch screen it is not the place i tapped that opens because it is not aligned
What can i do because i am all out of answers
ps there is no warrenty anymore
Greetz Hatchy
Click to expand...
Click to collapse
When your PPC is at the alignment part of the start up process simply plug it into your computer and let activesync run. You do not need to set up a partnership at this time to do this.
Explore your PPC and go to the windows folder and then to the startup folder and delete the welcome file in there.
Soft reset your PPC and you are good to go!
I had an IPAQ for years that had a bad spot in the middle of the screen and this is the only way I have found to bypass the alignment.
I am stuck on the align screen in a loop as well. What program did you write to skip the screen. I am not able to use the phone because of that. I am really terribly stuck. Please help. Thanks.
I hear placing a blank text file named "welcome" with the extension ".not" on the root of your SD card after hard resetting will bypass the Windows Mobile setup. And until you get your screen repaired (if ever) and if you have a working DPAD, then you can download a free, configurable mouse cursor here. Just go the the third post and click on the attachment I posted.
Dave
Well,
For what it's worth,
I found out on my brother's Qtek S200 that was also in a loop, that it automatically passed the align screen after some 15 times.
Later I found this in the registry:
HKLM\Hardware\Devicemap\Touch\MaxCallError(=16)
So I assume you can tick the align screen 16 times before it continues?
it works!!

Strange Issue with Screen Alignment

Recently got a new job and in storage was an old (thought to be broken) Cingular 8100. I figured I could use the parts and hack together my old MDA (USB port broke off of main board). Before doing any of this I flashed it back to the original Cingular ROM and thats when I noticed the issue with why the original owner thought it was broken. The screen alignment wizard would not pass, you could sit there forever and keep hitting the points on the screen and nothing. I used this tool to get around the alignment screen:
http://forum.xda-developers.com/showthread.php?t=355010
and found that nothing I did would fix it. So I pulled out my old MDA and popped the screen and digitizer on to the 8100 and still had the issue. Weird. Downloaded Manilla 4 ROM and flashed, still having the issue. Even more weird. Looked back over the post from above and on a whim, connected up via CERegEditor and popped in the Reg entries listed in the thread and soft reset. Problem solved!!! Although, without being able to do the alignment without a soft reset the ext rom did not run properly since it was soft reset before it could run.
I still found it weird that the reg entries did not come over with the ROM so I did another flash and bam, problem came back. Ran the utility again to bypass the screen alignemnt and after looking deeper I found that while in Vertical mode, the screen thought it was in landscape, and while in landscape it thought it was in vertical. Flashed again but when the alignment came up, I did not press where the pointers were, I pressed where the pointer would have been in landscape mode even though it was in vertical mode and it let me through. Ext ROM installed, reset, connected with CERegEditor and entered the correct reg entries from the post and bam, everything is working.
So I guess the screen alignment data stored in the REG are not part of the ROM??? Can anyone shed some light on that?

Require HTC Touch 3G Calibration File

Guys,
I own an HTC Touch 3G.The Touch Screen suddenly stoped working.I tried Hard Reset,then it went into the Known loop of Align Screen.I somehow managed by skipping the Align Screen using the Remote Screen Alignment Tool.
But to make my Touch Screen to work, I need the Calibration Data File which by using Remote Screen Alignment Tool i can put the alignment for my Phone (Hopefully,Not Sure)
Any Tips & Suggestions are always welcome !!!
Plz help me to save my phone ...
Thanks,
Bala
t3232 help!
i have bought a htc clone t3232.i have problem with the touchscreen,works complete wrong!i have done soft/hard reset but i cannot resolve the problem.
i cannot enter to my phone because i cannot enter my password!
i have tried many times to calibrate the screen but every time the problem remains!please help i have the phone 2 days!
Guys,
Anybody can create the calibration file using Remote Screen Alignment Tool & provide me...
It will make my Touch screen to work...
Thanks,
Bala
ulvergr said:
i have bought a htc clone t3232.i have problem with the touchscreen,works complete wrong!i have done soft/hard reset but i cannot resolve the problem.
i cannot enter to my phone because i cannot enter my password!
i have tried many times to calibrate the screen but every time the problem remains!please help i have the phone 2 days!
Click to expand...
Click to collapse
I got problems with the touch screen also, when i press something on the screen it highlights above or below my selection, writing SMS was nightmare.So i went to htc service and they replace the "touch digitizer" and now my problems are history, everything works like charm.I think you should try that.

[Q] Need Calibration Data For HTC Jade 100 (T3232)

Hi,
i have HTC Jade 10 (t3232) with me from last three weeks i am having some touch screen (Calibration) issues, like it is not pointing out exactly when i try to calibrate
so i did hard reset, after that on first startup , it was going on and on looping on screen alignment screen, somehow i manage to skip or bypass that screen by using Remote Alignment Screen tool
i also tried and install new ROM by doing HardSPL and now screen alignment works fine on first boot
but after using my phone 5 to 10 minutes my cell phone calibration got out or changes its coordinates in registry, than i search for the calibration data of HTC JADE 100 and manually enter it in phone's registry
( Can anyone post the exact and correct values or data of Calibration for HTC JADE 100 (t3232), may be it will work. )
after inserting calibration values that i took from forum in the registry, it works fine on middle portion of phone except top and bottom portion, and this thing is going on and on
after that i research on XDA forums about this issue and came to know that i might have an issue with my screen digitizer, if i change my screen digitizer it might work again
but i am not sure whether it is a digitizer issue, touch screen issue or any software issue or what, i am very upset from last 3 weeks , any one can tell me after reading the above mentioned problems that what happened to my phone and what should i do,
your help is appreciated.
Thanks.
I have the same problem, I need the touch calibration data to insert the cell regedit
Any body please???? I have the same problem aloso
looking for this too!
OOOOOH Yeaaaaah, I found the HTC Touch 3G (Jade) CalibrationData = "520,387 201,800 208,141 832,146 826,788"
Is ur problem fixed after inserting these values.
Sent from my HTC Desire using XDA App
Touch 3g caliberation details.
salmansaeed said:
Hi,
i have HTC Jade 10 (t3232) with me from last three weeks i am having some touch screen (Calibration) issues, like it is not pointing out exactly when i try to calibrate
so i did hard reset, after that on first startup , it was going on and on looping on screen alignment screen, somehow i manage to skip or bypass that screen by using Remote Alignment Screen tool
i also tried and install new ROM by doing HardSPL and now screen alignment works fine on first boot
but after using my phone 5 to 10 minutes my cell phone calibration got out or changes its coordinates in registry, than i search for the calibration data of HTC JADE 100 and manually enter it in phone's registry
( Can anyone post the exact and correct values or data of Calibration for HTC JADE 100 (t3232), may be it will work. )
after inserting calibration values that i took from forum in the registry, it works fine on middle portion of phone except top and bottom portion, and this thing is going on and on
after that i research on XDA forums about this issue and came to know that i might have an issue with my screen digitizer, if i change my screen digitizer it might work again
but i am not sure whether it is a digitizer issue, touch screen issue or any software issue or what, i am very upset from last 3 weeks , any one can tell me after reading the above mentioned problems that what happened to my phone and what should i do,
your help is appreciated.
Thanks.
Click to expand...
Click to collapse
Calibration Coordinates for Touch 3g T3232
527,519 209,847 219,159 831,188 839,848
To bypass screen alignment create Welcome.not file at the root of SD card,

Categories

Resources