Screen alignmentproblem after screen replacement - Touch HD General

After a busted screen I replaced the LCD and Digitizer. After that I didn't make any changes to the software (ROM, nor settings) of the HTC.
LCD works fine, but my screen alignment is bad. On almost all items I have to thick on one item beneath it to get it, also some items are not reachable due to this problem.
I managed to start the alignment proces with the use of the Remote Alignment tool, alle goes well but the upper two crosses. The digitizer simply doesn't respond to these and after al while starts over again.
Is it normal that you have to align your screen after a digitizer replacement?
Will it help to hard reset my HTC? (I'm using a hacked ROM, last one from Dutty WM6.5, so it doesn't start automatically with the alignmentproces)
When the upper crosses don't respond in the alignment proces, does this mean the Digitizer isn't ok?
I found a thread about Remote Screen Alignment on this board (/showthread.php?t=355010). Will this help for me? The phone is almost unusable so installing / using PHM Registry Editor will be almost impossible.
Lot of questions, hoping for some answers

Almost 2 days, 69 views and no answer?
Please guys, I'm missing my beloved HD

Related

Is this the forum for repair advice? Digitiser recalibration

I dropped my phone and the screen now doesnt respond properly: The hardware DID successfully upgrade to the XDA ROM. But touching it causes the backlight to go on, - but most of the keys dont do what one would expect them to do: The phone turns on with a reminder from the calendar on the screen which wont DISMISS or CLOSE. Pressing on the windows logo and then on the phone key causes the calendar to come up and I am not sure which numbers are entered when I do manage to get the phone to come onto the screen (none of the right hand numbers seem to work at all). Does anyone recognise these symptoms and/or could they just show that my SX-56 needs the ROM RE-flashing? I should add that pressing the Master Reset button with this ROM in place seems to make the phone shut off and then when you restart it, all of the data remains in place. I wonder if there is any possibility that the XDA ROM has prevented the reset button from working normally?
A user on another forum said that to him, '"Sounds like the digitiser is up the swanee - have you tried recalibrating it?"
10-12 vertical black lines started appearing to the right hand edge of the screen. Sometimes they are there, sometimes not. THere is usually at last one there somewhere. At about that time the screen stopped responding as I mention. Today the left third started displaying the same veritcal lines, though spaced quite far apart (about a millimetre). Screen doesn't APPEAR cracked: Does this sound like a digitiser and if so, how do you recalibrate it please or is there a link to somewhere on the XDA site which I cant find which might tell me? Or could it be the cable is loose in the circuit board? As you touch the lower right hand corner of the metal casing where the vertical lines are, those lines flash (the right 10 or 12) on and off. And every coloured bar everywhere on the screen or word of text has vertical lines on it (the white parts don't)??
Someone on ebay has said that his phone "fell from my pocket and onto the carpet and the screen cracked, I then used it for about a week" "I sold the screen to someone cause the wanted the touch pad part of the screen for there phone". and wonder what it was he sold or which part can be replaced on it? IS there a touch part and a screen part on this phone?
To be honest, itsounds like you have brocken a connection somewhere between the LCD and the gfx output, probably not possible to repair yourself.
I wonder where the break would be?
I thought that might be the case: I wonder if it would be worthwhile trying to get another screen?
I should probably try to take the unit apart and see if some break somewhere can be identified if it is a break as opposed to some electonic part having failed. It SEEMS to be in the lower right hand corner?

Touch Screen Not working.. plz help.

Hi mates yesterday i bought a used herm...with excellent condition. but when i opened any dialog. the window closed automatically. and the screen light remains always on. and touch is creating problems.
and after some time the touch screen totally stop working. i dont know what happened. al the buttons are working fine. i upgraded my t-mobile herm to its original t-mobile wm6 rom. and again the touch screen is not working. and the screen light always stay on..
so is this hardware or software problem.?
guide me if you have any clue about this..
according to my thinking.. i think some button is pressed continuesly.. but everything is working fine.. only the touch is not working.
broken digitizer for the touch screen, buy a replacement lcd/digitizer together and replace yourself, about $100Aud. Use Mike Channons site to download the service manual. Use the search function and type in "htc service manual hermes".
As for the light, you will have to use your buttons to navigate to settings>system>backlight>battery power and external power. you can select how long the backlight remains on for.
Cheers...
Hi mate thanks for your reply.. Actually the situation is that. the screen is working perfectly. all buttons are also working perfectly. but suddenly the touch feature stopped working.
that time i was just opening some menus and they closed automatically. it looks like that there is some button pressed. and the screen light never stops. it continuously remains on. all buttons are working perfectly and everything. on the touch feature is not working.
i upgraded my device with genuine shipped t-mobile wm6 rom and again it stopped at the starting screen where i have to click the screen and the device brings the window for stylus adjustment.
so i wanna ask that is this also possible that some touch drivers are corrupted or something like this.? or is this a hardware failure.?
Kind Regards
I had same problem, it was hardware. Thats why I said to change the lcd. It is theoretically possible to replace JUST the digitizer, BUT, it is a MAJOR hassle.
As for getting past the alignment stage, look up Remote Screen Alignment. Its a cab file that stores the alignment settings on your pc. You WILL have to have a friend that has the same phone so you can get their settings as you need to copy them to your pc first. You can then copy the settings to your phone so you can use it until you replace that pesky lcd...
Cheers.....
I had a similar problem with my hermes. After a lot of investigating, I found out that this is a heat related issue with the hermes. The unit will heat up an some connection somwhere gets messed up and continually registers ghost taps on the upper right corner of the screen, which causes the continual opening and closing of programs/task manager. This overloads the phone which then causes the screen to eventually become unresponsive due to excessive computing.
With my phone, it must be heat related because it will only occur during or after heavy use or overcharging. Other people have had this exact problem with the conclusion being overheating. The worse part is, there is apparently no way to fix this, replacing the screen doesn't change anything. setting your screen alignment very far left will fix the problem but then everything you tap needs to be compensated for.
Good luck, hate to be the harbinger of bad news, but it's better to know whats wrong and that you can't fix it then not know whats wrong and keep trying to fix it.
same problem here... only my hermes is overheating already after 5 minutes use...
in the morning it works and when i put it in front of the airconditioning the touchscreen also works...
somebody who has an idea where to look for a solution??
kingsfan said:
same problem here... only my hermes is overheating already after 5 minutes use...
in the morning it works and when i put it in front of the airconditioning the touchscreen also works...
somebody who has an idea where to look for a solution??
Click to expand...
Click to collapse
Some of the suggestions in the white screen thread/s might help. The problem is that those who have the heat related problem will find it very difficult to trace the actual fault. The heat may be causing miniscule expansions on the boards / components and connectors. The tiniest of cracks or poor connections can therefore break with the expansion.
Another theory is that rather than heat it might be a capacitor that is breaking down either over time or again through heating. Unless you are a skilled electronic engineer that is virtually impossible to check, particularly since schematics are not available.
You might just be lucky if you dismantled and re-assembled - it might just re-set a connector or adjust a board so it does not get affected in future. That would be very much a matter of luck and of course potentially the situation might be made worse!
Mike
Hi mates. I am back with some issue.. i moved my device to a repair center and he said that its a software issue. and he fixed my device without changing any rom.. i dont know how..
but again when i open some window like programs. the right scrollbar make a problem... when i move scrollbar it automatically press the top close button..i aligned my screen 3 times but same problem with right side scroll bar.
and after playing with it. the touch totally stopped.
now the thing is.all the buttons are working fine and everything is working fine. even sms and calls. but when i check sms and press my scroller button. it displays the right click menu instead of opening the sms. and the screen light is continuesly on. as something is pressed. so. i think this thing wil help. i am now trying this method to check my pc.
http://inuchanbt.blog54.fc2.com/blog-entry-99.html
check this out as well.
i will send you details soon.
might just have something lodged between the case and screen.. also to get rid of the screen alignment, cable it up and delete welcome from the startup programs and then reset it.. should get you past it so at least you can use it until you repair your screen

Screen alignement PROBLEM !!!

Hi there,
i have problem with screen alignment after I dismanteled my trinity and cleaned it because it was all dusty.
After putting everything together my screen was not aligned. I tried to align but it just kept asking me to align forever.
I did dismateled it again and put together, flashed rom again but it is the same...
Anybody having any idea ? please...
New digitizer ...
it seams that only solution is new digitizer..
so I ma waiting for it, hope it comes fast...
Hello,
I broke my screen (only digitizer) and bought an replacement. After replacement i could not align my screen. When i touch the first cross, nothing happens. i had to soft reset the phone to bypass the alignment. The screen 'works' that means that it responds to touch, only is misaligned.
What is your experience with the new digitizer?
Arjan
Fixed the alignment problem. FtouchFlo was interfering with the screen alignment. After stopping FtouchFlo i could align it just fine. Screen is working with the new digitiser

Advice after touch screen no more work

Hi,
The touch screen of my HTC elf doesn't work anymore.
I am going to order some parts to change the digitizer myself and also the casing to make it look a little newer.
Anyway, I'd like to understand how the touch functionality works exactly. Is it a pressure on the digitizer itself that make a "touch" or is it a pressure on the digitizer that press the screen and this action make a "touch" ?
When I power my disassemble Elf, a pressure on the screen itself doesn't do anything....
I'd like to know if I need to order a screen as well
Hi,
just replaced my own elf's digitizer a month ago... and the phone is like new.
To answer your question it's the digitizer that reads pressure and sends the data to the system (if you already disassembled it you should have noticed a flat cable that connects the digitizer to the board).
So if the screen on your elf is working you should solve the problem by replacing only the digitizer.
You rock, I order now

[Q] Incorrect Error Diagnosis at HTC Repair Centre

Hi,
I had the following problem with my HTC Diamond 2 (it might have got wet & it might possibly have had too much pressure on the screen)
Problem:
The mobile boots ok and the normal buttons at the bottom work fine, as do the volume up/down buttons. The display, however, has what looks like the newton rings and when I press the display it detects a 'press' about 1cm to the left of where i pressed. This means I can't use the right hand side of the display and also can't enter my pin.
Error Diagnosis: (from Arvato Services in Germany)
Mainboard is defect. Cost to repair = € 303.17
Is this possible ? If there was a problem with the mainboard then I would expect to see other problems - and at present, I can only see that the touchscreen has a problem.
Please let me know what you think, thanks in advance !
(ps there should be a question mark at the end of the 'title', don't seem to be able to edit though)
Based on your description and from what I've read, it's definitely the digitizer.
It is possible that you have a damaged board, but regardless, your digitizer is bad.
I would attempt to replace this yourrself then see if everything is fine before sending it to repair.
I had the same problem!
The screen was getting worse in alignment over a time frame of a couple of days. If replaced the digitizer and screen and all is back to normal ..... however it seems to work better then ever before.
The only problem left is dust between the digitizer and my screen, but this is my own fault since I didn't glued the screens. I'll re-open in the next few days and use some silicone to close the gaps. Mainly the volume key has an opening to the outside.
Good luck with the replacement!

Categories

Resources