Hi friends,
because my Polaris died I'm going to buy a HTC Pure. And for this I have a couple questions for you:
first:
HTC Pure locked AT&T with SIM and CID lock, unlocking using Olipro unlock,
Will I can use it with all the operators worldwide and flash a custum ROMs?
and second:
Can I change the body from
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
for such
Do it fit into the motherboard?
SIM and CID should set you up.
Regarding your housing, not sure about the fit, but you should consider the number of screen failures with the Topaz is high compared to the Pure which I have not seen.
Yes, if you are going to use Olipro, it will work, I did the same thing on my Pure and it works great now.
As for the second qn, don't do that, it will not fit.
Nag
Bruce Inman said:
SIM and CID should set you up.
Regarding your housing, not sure about the fit, but you should consider the number of screen failures with the Topaz is high compared to the Pure which I have not seen.
Click to expand...
Click to collapse
What do you mean with "screen failures", this problem relates to the release of a series of defective devices?
Please tell me what I should first pay attention.
Diamond2 has wery sensitive touch screen and it mailfunctions if the device is carried in pockets/bags with screen unprotected
search the forum for "touch sreen woun't untouch" or somethnig like that....my first screen failed to untouch 3 months after purchase, secondone is 6 months after still working with no problem, but allready has a slightly visible dent in lover third of the screen....build quality sucks*, big time (and still woun't sell mine )
*first screen was replaced under warranty, and as I write my device is again at warranty service - volume buttons started pressing randomly....strange( currently I'm not selling mine, but I'am one stupid failure away from selling....phone is scratchless! )
FW-eXXon said:
What do you mean with "screen failures", this problem relates to the release of a series of defective devices?
Please tell me what I should first pay attention.
Click to expand...
Click to collapse
If you search the forums for "Newton Rings" you will see many posts regarding Topaz screen failures. Some users had theirs fail 2 or 3 times after repairs.
I'm not sure if it was a specific bad batch released somewhere but I have not seen this issue on any Pure.
I can tell you that the Pure will fit in the Diamond 2 housing(and vise versa) but the problem is the antenna. If you could find an antenna for the TD2 housing, it would work, otherwise you would just have a PDA
oops..... repeated posts
TNX friends, the "oil" Newton ring, its something strange, and I disappointed in HTC Support. I will looked around the screen carefully and check for defects when my Topaz arrived, and in future will use screen protector. I read that overheating caused the newton ring.
If I find Diamond2 antena ill try to replace housing of Pure and will se what we got.
Again thanks for replying, how many did not seek, has not found information about the change of the houing, and known problems with Topaz, and here just only clear answers from You.
Related
Hello all, i'm facing a very serious problem with my skin.
I woke up the morning and the screen of my Atom was awful! I can't describe it because i don't know what the hell it has!
Here is 2 pics to see my problem:
With the screen off the problem is very obvious on the upper left corner
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
A pic with the screen light on (the problem isn't so obvious)
I'm in desperate position, i don't know what to do!
Is there a way to fix the screen? Do i have to buy a new one? If yes, do you know from where i can buy it? Unfortunately i can't send it from Greece to Hong Kong for the official service.
Any help appreciated!
Bill
Yes there is...
Hi Bill,
Im very sorry to hear about your screen. the problem with the screen is that the backlight of the lcd is not functioning. ( Its called BPD-light).
there are 2 options : 1. you can change the whole lcd screen, but thats pretty expensive if its not under warranty 2. you can replace the BPD which is very cheap actually (35-60$ ), but it is very rare to find.
In my store we fix those problems.
if you are interested, you can contact me : [email protected]
Goodluck!
Not sure whether it's the similar case as mine. My screen was ever like your atom snap shot a few times. Very clear when it's screen off. Mine's due to the screen got depressed a bit too hard (while in the pocket or doze off on bed with my atom ) that it some how stick to the one beneath. What I did was just to press that area with little preasure and it got back to normal. Hope it helps.
Re: Yes there is...
igal said:
Hi Bill,
Im very sorry to hear about your screen. the problem with the screen is that the backlight of the lcd is not functioning. ( Its called BPD-light).
there are 2 options : 1. you can change the whole lcd screen, but thats pretty expensive if its not under warranty 2. you can replace the BPD which is very cheap actually (35-60$ ), but it is very rare to find.
In my store we fix those problems.
if you are interested, you can contact me : [email protected]
Goodluck!
Click to expand...
Click to collapse
Umm, what??
The backlight clearly is working in the second photo.
Thank you all for your replies.
Yeah, it is the screen's problem and not the backlight.
So, the device it's on the way to HK for the official service and LCD's replacement.
I have seen similar circumstances in many TFT applications (I used to repair digital cameras).
My hypothesis:
The problem is perhaps liquid trapped next to the reflective diffuser sheet(used for backlighting) a piece of opaque polarised plastic paper.
I think water has got between the plastic rear membrane and the diffuser paper, and it is trapping it, in what can only be described as the capillary effect. (HTC might disassemble the LCM, let it dry, and then clean with isopropyl, or just replace it because it's too much hassle).
Finally my Atom is in my hands with the screen replaced!
I have sent my Atom ~20 days ago to Hong Kong with the help of baubaubau (http://forum.xda-developers.com/profile.php?mode=viewprofile&u=83579).
I've shipped the Atom to him, and then he has delivered the device to the O2 Support. Also, because O2 has run out of LCDs he gave them a strange push for not the replacement be delayed.
So, i have to thank him in public.
If you have any problem with your device or you want to buy a new one don't hesitate to come in contact with baubaubau. [/url]
I bought an imate jasjar on 31.08.2006
Returned on 1.09.2006 with a faulty screen when device is locked into landscape mode.
imate replaced it with a NEW device on 4.09.2006
Screen fails again today 7.09.2006 on the new device.
Different packaging and IMEI number.
I guess at least this one lasted 2 days and didn't fail out of the box like the first device!
Has anyone else had screen problems when changing into landscape mode.
Mine fades the screen out white and has pink or blue fine vertical lines.
Do I try another or ask for my money back?
Thanks in advance.
my screen image changes smoothly from landscape to portrait without any screen artifacts. i even took it off and tightened it up after i dropped it and it became loose.
U gotta Try another.
Of course U gotta Try another.
U can't desert a JASJAR like that.
Regards,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
______________________
GURJEET SINGH BAGGA
Microsoft Certified Proff.
[XDA2,O2MiniS,P900i,]
Say NO 2 Pirated S'Ware,Illegal Cracks
A BIG :"NO" TO WAREZ
Regardless of what others Preach & Practise.
Believe in urself And Just DO the Right Thing.
skywriter said:
my screen image changes smoothly from landscape to portrait without any screen artifacts. i even took it off and tightened it up after i dropped it and it became loose.
Click to expand...
Click to collapse
..mines a bit loose actually, is it easy to take it off and tighten the hinge?
i have the same problem sceen turnin white with pink lines, i 'll send it to repair, it seems to be the weak point of the UNI
3rd New Jasjar- No Problems now
Took three returns and a jasjar from another production run to rectify the problem.
Appears to be a pretty cheaply made piece of hardware!
I'm on my third Uni - the first (a G3) was great until the USB connector dropped off (a known fault). The second (another G3) felt flimsy from when first I got it. The hinge got rather loose after I accidentally dropped it. Also the earpiece speaker died when I dropped it.
I now have a replacement - a G4. It is far better made - much more solid, with a better keyboard and screen.
BTW, skywriter how did you tighten the screen - did you have to take the whole thing apart (as appears to be the case from the repair / maintenance manual)?
Hi,
I'm pretty distressed at the moment. On Sunday while out I noticed that the alignment of my screen was out. I realigned the screen and the problem seemed less but the problem came back after a minute or two.
After some Googling I tried the credit card trick for solving the alignment issue and now my problem is much much worse. I can not align the screen because I go in a never ending circle.
I suppose the best way I can describe the issue is, if drawing on a program like Note, the screen goes further out of alignment the further to the right of the screen I go. If I run the stylus down the right side of the screen the line is drawn about 1/3rd of the way into the screen but goes further into the screen at an angle as I run the stylus down the screen.
If I try to draw a box in Note around the screen edge the effect is like this;
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I also tried to loosen the screws at the back of the screen when slided out but I have now lost one of the screws and frankly I think the online fixes have done nothing for me except void my warranty and make it worse.
My questions are basically
1) Anyone else have the same issue and find a fix?
2) Will a missing screw and a homebrew version of Windows Mobile 6.1 mean the warranty is now void / HTC won't repair it and if so
3) Where / How much will it cost to get this repaired?
I really love my TyTN but it cost far too much for me to just "replace" and I really could do with it being repaired for under £100 or preferably for free.
Danny
This problem has been around since the Hermes first came out. There are those that claim that various things will work to cure the problem. Having had a Hermes that did this I can say nothing worked reliably or fo more than short periods.
My suggestion is to revert to the original ROM or flash an official new one and then take a chance with that missing screw for a repair under warranty. I can see you getting a service centre to repair for £100 (though you coul check this out) I have also seen repairs supposedly done (usually an LCD/digitizer combo replacement) that continue to show the problem. I have certainly seen cases where folk have replaced the screen themselves and it has not cured the problem. Hence my guidance for a warranty repair/replacement.
Mike
Thankfully I found the missing screw yesterday on the floor, chance of chances.
I will try to flash the old rom and send for a repair, I contact HTC though their site. Do they reply often? Sometimes I've e-mailed companies and been ignored.
Might be worth giving them a ring?
Hi everybody,
I have a question regarding the HERMES screen/digitizer with which i have always had problems...
I have been using my O2 XDA Trion for a bit more than a year now and i have always had the screen (dis)alignment issue. As i do not have warranty anymore i decided to check out the source of the problem one week ago, so I did a lot of research (also in this great forum ) and diss/reassembled the Trion without any problems. The problem now is : While I was testing the Trion's touchscreen with the included pencil suddenly the screen behavior changed. I am, as you can see on the two pictures below, not able to get in to the lower right corner of my screen anymore:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
There is no way to get in the lower right corner of the screen, even touching at the very low+right point doesn't work. My questions therefore are:
- Do you think the root cause is a digitizer failure? (The LCD itself still works flawlessly...)
- Do you think buying + installing a new digitzer might fix the issue? Might it also fix the screen alignment problem?
- How "hard" is it to install it? Through my research in this forum i heard that soldering is needed?
Thank you very much for your answers in advance,
Cheers,
Philipp
Looks like a digitizer issue as you can't get any sort of selection to happen in that area but the LCD is not damaged as you said.
gehzumteufel said:
Looks like a digitizer issue as you can't get any sort of selection to happen in that area but the LCD is not damaged as you said.
Click to expand...
Click to collapse
That's very probably true. The other thing that can cause wierd effects is anything that may be pressing on the digitizer around the edges underneath the bezel. Unfortunately some Hermes suffer from the digitizer remaining sensitive to touch even under the lip of the casing.
Regardless, I would not be tempted to replace the digitizer only. Although it's theoretically possible, it's not an easy job (LCD and digitizer are stuck together and contacts have to be made, positioning accurate , danger of cracking the LCD etc etc). Despite extra cost I would personally replace LCD/Digitizer as one unit.
One final point is that replacement carries a chance that things will not be perfect after replacement. This is because of various sensitive parts that can be affected when dismantling. eg. the d/pad connector.
Mike
Other way would be to find a "broken" Hermes (make sure its not the same problem or whitescreen) and use the whole slideout screen section. I did this and it worked fine...
Got my spare Hermes off ebay....
Cheers...
Hi guys,
just wanted to give you some information on the results.
I ordered the replacement screen 2 weeks ago here in Germany for about 45Euro (which is quite cheap i think, yeah ).
Everything worked fine so far. I installed the screen as described and it directly worked without problems. I have been using the Trion for more than one week now and the best thing is : Even the screen alignment problem seems to have dissappeared with the new screen, yeeppeh
Btw: I was a little surprised but the "new" replacement screen had the same date of manufacture on it as my "old" screen (which is in fact >2 years old). Nevertheless it worked...
So thank you all for your responses and help!
Cheers,
Philipp
My HD2 appears to have some big time screen problems, so i wonder if anyone has any sugestions.
Background
It never really lived in a case and the inevitable drops happened. That ended in about November when one drop too many caused the screen to crack. I replaced the digitiser and lcd screen which got it all working again happily, though beecause of the amount of fiddly stuff involved the chassis never truly fit perfectly, the screen protruded ever so slightly above the edge of the case, etc.
Fast forward to last weekend when for no apparent reason (i hadnt dropped it or anything) it started to behave erratically, not registering screen taps and then suddenly doing many things at one, making it almost impossible to send text messages and use effectively. My thought was that maybe it was losing calibration so tried aligning the screen but nothing would really happen.
Furhtermore it seemed like the bottom section of the screen had almost no responsiveness at all.
I therefore thought it might have something to do with the connections inside the machine, so i decided to take it all apart and check all the connections were sturdy. Thats when the real problems started because when i put it back together and turned it on, i had a horrible display that makes it next to useless.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I actually just fired it up to check that it was sill the case and it seems slightly worse than this picture!
So the questions. Firstly, does anyone know what might be the problem here. Is it likely to be the connection between the processor and the lcd, or soemthing more of a problem? How easy is it likely to be to sort it? A case of a completely new screen needed? Or is it likely to be something fairly simple? And would those problems with teh LCD screen be a similar cause of the calibration problems (i thought the digitiser might not be working properly, hence the original decision to take it to pieces!)
Hope someone can help. Happily my upgrade was due last friday, buit it would be nice to have a working phone for spare use etc.
Steve
It seems to me a bad LCD(100%) and probably a bad touchscreen!
As i suspected. Has anyone else with a replacement digitiser/lcd had any similar problems?