Stuck on t mobile stick together screen... - HD2 General

ok so i had kumars v 1.4.. and than updated to his v 1.5.. to update, i synced the phone with active sync and ran the RUU file.. now im stuck on the tmobile stick together screen.. i dont want to touch the phone until you can give me some advice
im showing
R 2.08.50.08_2
G 15.34.50.07U
D 2.10. KUMAR P1
PLEASE HELP!!!!!!!!!!!!!

Firstly, better to ask this in the kumar thread.
Secondly, try flashing it again, could be a bad flash.
Thirdly, your radio doesn't quite match the ones listed by kumar. (Although it is very close, so unlikely to be that.)
Oh, and you did do a hard reset after flashing, right?

yes hard reset was performed to no avail.. but just to clarify as long as i flashed HARDSPL the first time that will protect my phone from being bricked correct|?? because if thats so i will try to flash the rom again.. im not able to flash again because active sync is not recognizing the phone

oh i am so sorry.. thank you very much for your quick reply...

Take the battery out >> put it back in >> Hold down the volume down button >> press the Power button. This should take you to the bootloader screen and from there you should be able to reflash.
Good luck

Flash the stock ROM again from the bootloader as the above poster has stated. If not flash the ROM from the MicroSD card.

AllTheWay said:
Flash the stock ROM again from the bootloader as the above poster has stated. If not flash the ROM from the MicroSD card.
Click to expand...
Click to collapse
The stock rom isn't out yet.
2.10.0 is out, but the hd2's came shipped with 2.10.1
Working on it.

Well.... Any updates? Im sure you didnt go to sleep with it being stuck on the StickTogether screen lol

If I was the Op, I'd task 29 and reflash. It should works fine. I've never brick and htc phone and I dont think the HD2 is that easily brick if you use common sense.

romeo0119 said:
If I was the Op, I'd task 29 and reflash. It should works fine. I've never brick and htc phone and I dont think the HD2 is that easily brick if you use common sense.
Click to expand...
Click to collapse
the tmous is realy easy to brick. just flash any radio with a ..51.. version.......... brick.

alright..so what ended up happening is from boofloader i tried to reflash 1.5 to no avail..
so rather than trying to figure out how to flash back to stock rom, i figured i would try kumars 1.4 which i had installed previously. And sure enough everything worked again .. sorry it took so long to update. last night it wa s too late for me to post and ive been working the whole day..

pookeee said:
ok so i had kumars v 1.4.. and than updated to his v 1.5.. to update, i synced the phone with active sync and ran the RUU file.. now im stuck on the tmobile stick together screen.. i dont want to touch the phone until you can give me some advice
im showing
R 2.08.50.08_2
G 15.34.50.07U
D 2.10. KUMAR P1
PLEASE HELP!!!!!!!!!!!!!
Click to expand...
Click to collapse
I had exactly the same problem when flashing v.1.6. Then I flashed back v.1.5 and it works OK.

Hi I have the same problem, though I didnt flash a custom rom.
I'm stuck at the stick together screen, after flashing a stock rom to my tmobile hd2.
I tried to reflash but it gets stucked at 0%, and it wont move.

Raioneru said:
Hi I have the same problem, though I didnt flash a custom rom.
I'm stuck at the stick together screen, after flashing a stock rom to my tmobile hd2.
I tried to reflash but it gets stucked at 0%, and it wont move.
Click to expand...
Click to collapse
try to force it into bootloader first and then flash.

HotShotAzn said:
try to force it into bootloader first and then flash.
Click to expand...
Click to collapse
I did it, it is still stuck at 0%

did you flash from sd card? what does your spl say in bootloader? could be that you have flashed away hspl, and the stock you are trying is not quite a match. (There are several 'stock' versions i believe)
try re aply hspl, flash the rom from usb, then use the hspl app again to remove the hspl, and hey presto, , back to stock.

I dont have the red inscriptions when it shows the sticck together logo.
I didnt flash from the SD card(...) basically this is a stock phone with a stock rom I guess.
so I tried HSPL2_1024_RUN
it told me that my version was 2.08.0000 and it gave me 2 choices, going to 2.08.HSPL
I tried both, but it gives me an error.
CRITICAL ERROR
Flow: 00000006
Error code: 00000000
Description: Unknown
ps: Im constantly on the forum, so just reply and I will reply within 5 mins

go into bootloader manually, plug into a usb port around back of pc, use one you dont usually use, wait for it to connect, and run hspl1024, remembering to right click & run as administrator. Choose 2.08.hspl, and cross your fingers. Ill cross mine for you too.
if hspl wont load, all i can suggest is different usb ports, maybe remove the drivers, and letting it downoad new ones from the net, especially if you've ever used mtty.

ok so it does not work, hum I guess i'm screwed what can I do?

by the way here is whats written on the bootloadeer screen:
PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40

Related

Phone stuck at white screen with HTC

Hi there,
I really need help!
I wanted to flash my phone with a nbh file, but I could not enter my bootloader.
I had installed HSPL3.
Now someone told me to use Flashaholic ROM update utility.
I did this, and a black screen with a % indicator appeared, not too long, it restarted, and went into a white screen with htc in the middle.
Restarting with volume down button pushed doesnt bring me into bootloader.
What can I do now?
I really need help!
Unfortunately, if you can't get your HD2 to boot into the bootloader, there's not much to be done.
Are you sure you had HSPL installed? Because from what I have heard, HSPL is there to always allow you to use it for flashing stuff, regardless of the integrity of other software parts such as the radio or the ROM, so reaching the bootloader should not be a problem for anyone.
Can you connect it to your PC via USB? If you manage to get a connection, you might just have a chance to flash another radio/ROM.
anrabi4 said:
Unfortunately, if you can't get your HD2 to boot into the bootloader, there's not much to be done.
Are you sure you had HSPL installed? Because from what I have heard, HSPL is there to always allow you to use it for flashing stuff, regardless of the integrity of other software parts such as the radio or the ROM, so reaching the bootloader should not be a problem for anyone.
Can you connect it to your PC via USB? If you manage to get a connection, you might just have a chance to flash another radio/ROM.
Click to expand...
Click to collapse
I installed HSPL3, and it said it was succesfull so...
After that I installed a custom rom with an utility that came with it (Dutty's)
So far I know, I cannot get any connection, but I try to download a stock rom (an utility exe) from HTC.com.
But I think this won't work right? because you have to sync.
You could try and flash a stock ROM via the SD Card, see if that works. There are some instructions here on XDA in the ROM Development section, check it out there.
Basically, once you have downloaded an official ROM from htc.com, extract it as if it were an archive and get the ruu_signed.nbh. Rename it to LEOIMG.nbh. Then take your SD Card, format it to FAT32, place the LEOIMG.nbh on the card and put it in your phone. While holding down the volume down button, boot the phone and a white Loading... screen should appear and the flashing process should begin.
I`m afraid this won't work either, as the bootloader is supposed to show up in order for you to be able to flash anything, but it's better than doing nothing, so...
anrabi4 said:
You could try and flash a stock ROM via the SD Card, see if that works. There are some instructions here on XDA in the ROM Development section, check it out there.
Basically, once you have downloaded an official ROM from htc.com, extract it as if it were an archive and get the ruu_signed.nbh. Rename it to LEOIMG.nbh. Then take your SD Card, format it to FAT32, place the LEOIMG.nbh on the card and put it in your phone. While holding down the volume down button, boot the phone and a white Loading... screen should appear and the flashing process should begin.
I`m afraid this won't work either, as the bootloader is supposed to show up in order for you to be able to flash anything, but it's better than doing nothing, so...
Click to expand...
Click to collapse
Does not work, still hangs in htc bootscreen.
What I have to do now? =(
I hope you have any more suggestions for me.
I will read it within 20 min, because I have to go soon for 20 min.
I really need my phone fixed =(
Hi, if I remember correctly, you already said in the Artemis-thread, that the VOL DOWN button is broken. If this is the case, I fear there is not much you can do...
Have the same problem too.
I've installed a few roms with no worries, tried one about an hour ago that performs a Task 29 and i'm also now stuck at the white HTC screen...
it says the task29 was succesfull and then got stuck on the white HTC screen and the rom failed to load as the laptop did not detect a usb connection...
I've downloaded a stock rom and put it on the SD card named LEOIMG.nbh and tried pressing the vol down button, the Red,green,blue,white screen appears i can see
PB81100 HX-BC
SPL 2.08.Hspl 8g XE
0x05
CotullaHSPL 0x30
Then "serial" at the bottom or if i have the phone connected to the pc then "USB" appears.
If i hold both buttons and perform a Hard reset the phone asks to press Vol up button then says restored really quickly then freezes at the white HTC screen..
Any suggestions
Cheers
Actually got it sorted now, the rom had the Flashaholic utility built in which i haven't used before.
As we speak the rom is now installing phew (stop sweating now)...
Thought i had bricked it...
MaxKaul said:
Hi, if I remember correctly, you already said in the Artemis-thread, that the VOL DOWN button is broken. If this is the case, I fear there is not much you can do...
Click to expand...
Click to collapse
It's not broken, it just worked before I did the task29.
The phone is empty, and has no bootloader, and no ROM.
wakers said:
Have the same problem too.
I've installed a few roms with no worries, tried one about an hour ago that performs a Task 29 and i'm also now stuck at the white HTC screen...
it says the task29 was succesfull and then got stuck on the white HTC screen and the rom failed to load as the laptop did not detect a usb connection...
I've downloaded a stock rom and put it on the SD card named LEOIMG.nbh and tried pressing the vol down button, the Red,green,blue,white screen appears i can see
PB81100 HX-BC
SPL 2.08.Hspl 8g XE
0x05
CotullaHSPL 0x30
Then "serial" at the bottom or if i have the phone connected to the pc then "USB" appears.
If i hold both buttons and perform a Hard reset the phone asks to press Vol up button then says restored really quickly then freezes at the white HTC screen..
Any suggestions
Cheers
Click to expand...
Click to collapse
task29 DELETES the ROM. You NEED to install a ROM. A Radio-ROM should be installed automatically with task29. If this isn't the case, you need to install a Radio-ROM too. You can either install the HTC ROM or you can install a custom ROM like forum.xda-developers.com/showthread.php?t=612580
Suggestion: Enter bootloader -> connect USB -> install ROM with CustomRUU
MaxKaul said:
task29 DELETES the ROM. You NEED to install a ROM. A Radio-ROM should be installed automatically with task29. If this isn't the case, you need to install a Radio-ROM too. You can either install the HTC ROM or you can install a custom ROM like forum.xda-developers.com/showthread.php?t=612580
Suggestion: Enter bootloader -> connect USB -> install ROM with CustomRUU
Click to expand...
Click to collapse
Do I have to repeat it again? there is NO BOOTLOADER
joshoon said:
Do I have to repeat it again? there is NO BOOTLOADER
Click to expand...
Click to collapse
If you'd read the entire post, you'd notice, that I quoted the user "wakers", who seems to be able to enter bootloader.
MaxKaul said:
If you'd read the entire post, you'd notice, that I quoted the user "wakers", who seems to be able to enter bootloader.
Click to expand...
Click to collapse
Well im not able to.
I did a HSPL before then I putted a custom ROM Dutty's on the device.
After that I putten a Stock ROM on it again, and then I used Flashaholic, and after task29 it got stuck.
Well no bootloader means no HSPL which is good news for your warranty coverage..
Just go to HTC service and play dumb " uhm i was playing around websites with a flash game and uhm my phone uhm rebooted and is like stuck ever since in uhm HTC logo"
Now if the case for not being able to load the bootloader is a broken volumedown button, yeah ur pretty screwed, prepare to dive in ur wallet.
Were do you live? If you need help and there's one living nereby maybe we can help (p.e. a full battery) I live in the eastern part of the Netherlands (Overijssel) PM me if you can come.
On the Kaiser (my previous phone) I also had a problem I couldn't enter the bootloader anymore, but I can't remember why or what I did to recover it.
- If it was an allmost empty battery and recharged it?
- If I have used a special tool to connect?
I really can't remember.
If I read your story, I think you have loaded a corrupted NBH thru SDCard method, otherwise i think you cannot wipe your bootloader. Task29 only wipes the ROM area not the bootloader.
Have you tried to contact Bepe or Cotulla, cause i think they know everything about (H)SPL.
Otherwise you can start building a new house (you've got your first brick )
have you checked you battery connections, the middle one is notorious for getting bent out of shape at which point the battery will not charge and you can't flash you ROM.
chris2busy said:
Well no bootloader means no HSPL which is good news for your warranty coverage..
Just go to HTC service and play dumb " uhm i was playing around websites with a flash game and uhm my phone uhm rebooted and is like stuck ever since in uhm HTC logo"
Now if the case for not being able to load the bootloader is a broken volumedown button, yeah ur pretty screwed, prepare to dive in ur wallet.
Click to expand...
Click to collapse
I'm 100% sure it's not the volumebutton, and yes Im gonna play a bit dumb ofc, but I already have another story.
henk-jan said:
Were do you live? If you need help and there's one living nereby maybe we can help (p.e. a full battery) I live in the eastern part of the Netherlands (Overijssel) PM me if you can come.
Click to expand...
Click to collapse
It's costs a lot for a trip to there.
Btw, I tried a full battery too, didn't work. (I have two)
webpatrick said:
On the Kaiser (my previous phone) I also had a problem I couldn't enter the bootloader anymore, but I can't remember why or what I did to recover it.
- If it was an allmost empty battery and recharged it?
- If I have used a special tool to connect?
I really can't remember.
If I read your story, I think you have loaded a corrupted NBH thru SDCard method, otherwise i think you cannot wipe your bootloader. Task29 only wipes the ROM area not the bootloader.
Have you tried to contact Bepe or Cotulla, cause i think they know everything about (H)SPL.
Otherwise you can start building a new house (you've got your first brick )
Click to expand...
Click to collapse
I think it's bricked man, my bro is looking for the papers soon, and then im going to the KPN shop (the provider), because the phone has been ordered from there.
nrfitchett4 said:
have you checked you battery connections, the middle one is notorious for getting bent out of shape at which point the battery will not charge and you can't flash you ROM.
Click to expand...
Click to collapse
All the connections look fine.

I need your help please! Bricked hd2???

OK, I received a T-Mobile hd2 that was and still is stuck on "stick together " screen. I tried the reset button on the back, taking out the battery, checked for bents battery pins, and I downloaded 2 "official" .exe roms and renamed to zip and extracted.the nbh file and renamed to leoimg.nbh and tried to flash them.via a formatted fat32 2gb SD card and only one worked, kind of but gets stuck at like 15% of the way?? For like 10 min..I just pulled the battery. .I tried it twice..Please help me out here..this is what is says on the bootloader screen if that helps??
PB81120. SS-B3
SPL-2.10.0000 8G XE
MICROP(LED) 0X05
MICROP(TOUCH) 0X50
AND NOW IT SAYS THIS (ON THE GREEN PART OF THE BOOTLOADER SCREEN), AND THIS IS AFTER THE FAILED FLASH THAT I TRIED..
"UPGRADE ROM CODE ERROR PLEASE TRY AGAIN" ?
Is that just saying that the flash failed?? Or something else??
Please help me out guys...as you can see I'm kinda desperate and exuasted in trying to get this.hd2 working again!! Preferably ANDROID FROYO..THANKS IN ADVANCE!!!
You need to make sure you are flashing the correct stock ROM. Try downloading and flashing the official T-Mobile US 2.13 ROM, that SHOULD get you back to working. Everything you are doing is correct, Fat32 formatted SD card, under 4GB....nice job searching before posting, that is to be commended. Anyways, try the 2.13 ROM and let me know what happens.
Have you tried a hard reset? Or task 29 while in bootloader mode?
Sent from my T-Mobile G2 using XDA App
Ok i tried the 2.13 rom and it flashed and said success! but then it just stayed at that screen?? so i pressed the reset button on the back and now its back to the stuck "stick together" screen!! ??? should i have waited till it rebooted after it said "succes "?? i waited like 5 min and nothing and i just pressed the reset button..or should i have taken out the battery??
Yeahhh...you may have jumped the gun a little bit...after is says success, it takes like 10 more minutes for the ROM to set everything up. Go into bootloader and try flashing it again with the stock ROM and wait for at least 10 minutes and see what happens.
OK ill try that if I get lucky enough for that successful update..LOL
But I flashed a hspl2 (2.08) and can't I just flash away?? (USB..bootloader mode) ?? Since the phone is always stuck on the bootloader screen..
I just open the exe flash program and connect my hd2 in bootloader mode and I get the USB mode on the bootloader screen and I flash away..but it but it always stops at a certain point...mostly 8%..???
Yeah you can just flash away like usual. HardSPL isn't required to flash an official ROM anyways.
what am i doing wrong!!?? i tried ,many roms but hang at 8% 95% of the time?? i tried kumars tmous v2.9 s23139 se rom, the ruu_leo_1_5_tmous_2.10.531.0_radio_15.34.50.07u, and T-Mobile_HD2_MR_Software_2.13.531.1, all stop at 8%???!! ...i always do task29 after every failed rom to be clean and start over..thats right..right??
i have the hspl 2.08
i have a feeling im flashing an incompatible rom that requires a different radio rom??
please give me a link to download the right rom...thanks
1st post, rom 2.13
http://forum.xda-developers.com/showthread.php?t=655653
i feel for ya man, i keep getting up and running , every thing runs fine, i get it to survive a few reboots, then dead.... stuck at the boot screen.
i cant wait for a solution to android running natively...
I tried but hangs at 8%????
i tried many other roms, kumar, core cell, official tmobile us roms, they all either stop at 0%, 1%, 8%????? im going crazy here!!! whats going on?? i have hspl 2.08 and i do a task29 before every flash, but the wierd thing is that it doesnt auto reboot after task29?? it should, right?? and even after a hspl3 flash it doesnt reboot, the phone use to reboot automatically after one of those??? no i have to take out the battery for 15 seconds and put it back for it to boot again into bootloader?? and wierd thing is that sometimes if a flash fails and when i get it the hd2 to turn back on and if i do the hard ereset (volume up and down and then press up to reformat) it then reboots and hangs at the boot image of the last failed flash?? i thought when i do a task29 everthing should be erased???
guys im about to LOOSE IT!! i have tried to flash this phone already like 100 times int he past 3 days, no joke!!! 2 times it reached 100% but even after it rebooted and i did a hard reset it would hang at the boot logo?????
please guys help me out!!! and im the type of guys thats not gonna stop unless it breaks or someone takes the phone away from me...lol
naiefelyemeni said:
i tried many other roms, kumar, core cell, official tmobile us roms, they all either stop at 0%, 1%, 8%????? im going crazy here!!! whats going on?? i have hspl 2.08 and i do a task29 before every flash, but the wierd thing is that it doesnt auto reboot after task29?? it should, right?? and even after a hspl3 flash it doesnt reboot, the phone use to reboot automatically after one of those??? no i have to take out the battery for 15 seconds and put it back for it to boot again into bootloader?? and wierd thing is that sometimes if a flash fails and when i get it the hd2 to turn back on and if i do the hard ereset (volume up and down and then press up to reformat) it then reboots and hangs at the boot image of the last failed flash?? i thought when i do a task29 everthing should be erased???
guys im about to LOOSE IT!! i have tried to flash this phone already like 100 times int he past 3 days, no joke!!! 2 times it reached 100% but even after it rebooted and i did a hard reset it would hang at the boot logo?????
please guys help me out!!! and im the type of guys thats not gonna stop unless it breaks or someone takes the phone away from me...lol
Click to expand...
Click to collapse
Did you have Android loaded on that same microSD card? Does it hang if your microSD card is out.
After you task 29 it should auto reboot, then you press Volume Down and Power to get into bootloader. Have you tried flashing from your PC via USB? If you are flashing form the card a stock rom, it will overwrite your HSPL to Stock SPL. You probably know this. Also if you flashed 2.13 then you need to install HSPL3 and not the original HSPL program. 2.13 has 2.10 firmware. HSPL only supports 2.8 firmware.
I've always heard when it hangs on boot up that it's usually something on your card.
it never had android, i got it with the stock firmware and it was messed up, stuck on "stick together" screen..and i never have the sd while im flashing via usb in bootloader.. i tried many roms, and task29 followed by hpsl3 and then i would flash custom roms and even stock roms but all fail?? all stop at like 8%, but the wierd thing is that even the task29 sometimes fails at 0% so im suspecting maybe its from windows 7? but i did try xp and the samething, the roms would stop usually at 8% or 0%??? ...weird?
ok i kinda fell like my mind is cluttered and confused..
i want to know, please..what rom is compatible with my current tomobile hd2 with hspl 2.08 colutta
so what rom should work fine?? with no problem?? and DOES IT MATTER WHAT MY RADIO ROM IS?? i have a feeling that if i have a older radio that it will interfere with the rom???
Ok i got it to accept a rom flash from sd card!! But it just stayed at the "update complete, update success" white screen??? I waited over 10min the i did a reset and hard reset...and now stuck at the boot logo??? I heard i might need a higher radio??? 2.10 or higher?? Is this why its not booting up?? Can i flash the radio through sd card??
naiefelyemeni said:
Ok i got it to accept a rom flash from sd card!! But it just stayed at the "update complete, update success" white screen??? I waited over 10min the i did a reset and hard reset...and now stuck at the boot logo??? I heard i might need a higher radio??? 2.10 or higher?? Is this why its not booting up?? Can i flash the radio through sd card??
Click to expand...
Click to collapse
You can flash a radio, just like a rom form the microSD card...
is there such a thing as a wrong radio version for a rom or "required" radio version for a rom?? will that cause the phone not to boot up???
naiefelyemeni said:
is there such a thing as a wrong radio version for a rom or "required" radio version for a rom?? will that cause the phone not to boot up???
Click to expand...
Click to collapse
I've never had issues using any Radio with any ROM really. Some combos work better than others but won't cause your problem. If I were you I would task29, then flash the 2.13 or the new 3.14 shipped ROM via microSD to take the SPL back to stock. Then I would flash HSPL3, then reflash a Custom ROM or the Stock ROM via USB. Then do a couple hard resets after that. If that doesn't work I'm thinking Hardware.
You can use any of these radios. http://www.4shared.com/dir/RFg27UmU/Radios.html Doesn't matter what ROM you are running.
Wtf!! I tried to restore the stock tmous roms (2.13 and the latest 3.14) and all would stop at 8%???? And i reverted back to stock 2.08 spl..still hangs at 8%??? But if i flash that core cell rom...itll say success 100%..??/ why???? Man this freakin hd2 is makin me go crazy...hardware issue maybe??
come on guys?? please help, its been like 10 days no reply...

[Q] Help Upgrading My Rom

Can anyone help me please... I'm trying to upgrade the rom to the latest HTC HD2 rom for O2. I connect the phone via USB, sync it and then run the RUU program from HTCs website. The phone starts the process and boots the phone to the 4 colour screen and then to the black HTC progress screen and then it hangs on 0% for a few minutes until the utility finally tells me its lost connection with the phone (Error 262). I've done soft resets and hard resets. Disabled firewalls. Tried on another machine. Even ran the utility under XP SP3 compatibility. Still no joy. Can anyone help?? Thanks
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
T-Macgnolia said:
Sounds like you might have a bad USB cable or that you are having timing out problems. First forget about the ActiveSync. All ActiveSynce does is help insure hour HD2 is ready to be flash by checking the battery level and such. Power your HD2 on but hold the volume down button down while powering on. When you see the tri color bootloader screen connect hour USB cable and wait for the Serial in the white bar of bootloader to change to USB and then right click the RUU of the ROM and select run as administrator. If this still does not work I would try another USB cable.
Click to expand...
Click to collapse
Thanks for this... i followed your instruction and used 2 different cables. No joy.
Anything else I can try that doesn't involved the device suffering a sudden impact with the nearest wall??
Cheers
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
mr_bacon said:
could it have anything to do with the phone being locked to O2... its the latest ROM for O2 that I'm trying to install.
Click to expand...
Click to collapse
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
silverwind said:
hmm....if you are trying to flash stock rom which is not intended for your device, you need HSPL or Gold card.
There are threads in Windows Mobile 6.5 section that will guide you on installing HSPL or making a Gold Card.
Good luck
Click to expand...
Click to collapse
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
mr_bacon said:
Well here's the thing, my phone is locked to O2. I'm trying to install the latest ROM from HTCs website for O2 customers. For the life of me I cant get it to install. I did install HSPL a few months ago when I tried to run Android from the SD card. That didnt work either. Like I say, I've done a hard reset. Could the HSPL thing be causing an issue. How do I get rid of it.
I hate being a noob sometimes!!
Click to expand...
Click to collapse
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
T-Macgnolia said:
To get rid of HSPL you just have to run the HSPL Utility avain and choose the correct SPL version for your ROM when it asks what version you want to flash. Remember HSPL has the stock SPL versions to, click on the link in my sig to download HSPL 4. Hint thecstock SPL versions all have four zeros at fhe end and the HSPL version do not.
You said you are getting error 262, this usually means you don't have the right SPL or HSPL one of the two atleast that is if I remember correctly. What ROM are you trying to flash and what does it say in bootloader right now?
Click to expand...
Click to collapse
Hi... Been away so only just got this reply.
The rom I'm trying to install is a stock rom update from the HTC website:
O2 (UK): 3.14.206.1
For the record, my phone is an O2 phone.
As for Bootloader? It currently says:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
Hope that helps. Really bugging the arse off me this is.
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
samsamuel said:
get hspl2,
put phone into bootloader manually first and connect usb lead
(thats why it was timing out on you ((error 262)) because the connection takes too long to reconnect when it reboots from winmo into bootloader, , if you do it yourself first, that solves this error 99% of the time.)
when 'serial' changes to 'usb' run hspl2, choose 1.66.0000 (i recommend this because 2.08.0000, whilst stock, is a tmous stock, so 'may' give problems, , totally unconfirmed, but i had issues recently removing android/magldr whilst spl was 2.08.0000, i switched to 1.66.0000 and it worked straight away, i have a slight hunch that spl 2 doesnt like to be downgraded in some circumstances, , if you preffer you could use hspl4 and go straight for 3.03.0000, since that is whjat your 3.14 rom will install anyway when you flash it)
when it reboots saying its done, immediately hold voldown to re-enter bootloader
when serial changes to usb, run your 3.14.exe
Click to expand...
Click to collapse
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
mr_bacon said:
Thanks for this but can I ask a favour... Can you give me an 'idiot guide' as to what to do? I'm a compelete noob to this kind of thing and don't wanna brick my phone.
Cheers
Click to expand...
Click to collapse
Ignore that..
Mate - you're a genius. Followed your instructions and it worked like a charm.
Cheers pal. You saved my brain
Erm, not sure how much more basic i can make it. (Ignore my descriptions, just follow the steps)
Power off, hold voldown,power on keeping voldown held,, see multi striped coloured screen, that's bootloader, you can flash from this screen.
First you should try without bothering to change the spl.
Enter bootloader and connect USB, run the 3.14 you downloaded. That's it.
If it doesn't work, try changing spl as in my previous post by entering bootloader, and instead of running the 3.14 you run hspl instead.
As for writing a guide, you already read the various "how to flash.." guides (there are several) and watched the (also several) YouTube guides before you even started this thread,,, didn't you? Didn't you?? If not then shame on you!
Post back and ill check tomorrow.

HD2 kinda broken what can i do?

Hey XDA
Hope someone out there have got some good advice. We have some HD2s where i work and i have been sent one that is acting kinda weird.
I simply can not get it to flash a rom (_HTC HD2_RUU_Leo_S_HTC_DAN_3.14.403.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship) - we only use normal HTC roms. When i try to flash it nothing happens, it boots into the bootloader and just sits there at 0% until i disconnect the cable, if i dont it will sit there untill it runs out of battery. Tried a few times now and same result.
i have also just tried a restore, to see if its the internal flash rom that is broken and the restore also fails. My own HD2 restores in like a few seconds but this one just sits there again, like when i try to flash a rom to it.
So is it totally dead or is there something i should try?
Have you tried to use task29 (via computer) , then flash (via nbh) the htc rom?
hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.
dkwolf said:
hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.
Click to expand...
Click to collapse
HSPL 2.08 & reflash original HTC ROM via PC USB.
Do you get any error codes from the flash utility ?
could be CID related but you should see error code.
Yes, trying it with HSPL seems like a good idea to me, too.
Because then you can also try other ROMs.
will try this stuff on monday - i just cba to do more work today
thx for the advice
Build a gold-card and flash from the SD slot. If that doesn't work, put it in a zip lock bag and then into the freezer for 10 minutes. After 10 minutes, boot the phone and try flashing again immediately in it's chilled state. If it get's ANY further, you have a bad overheating NAND and need a new main board.
got HSPL2.08 flashed and a Dutty 3.14 rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions in the bottom. So i am just gonna toss this one out, since its can not be serviced (supplier has gone bust).
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.
dkwolf said:
got HSPL2.08 flashed and a Dutty 3.14[/COLOR] rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions((edit - the RGD screen)) in the bottom.
Click to expand...
Click to collapse
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.
Click to expand...
Click to collapse
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.
samsamuel said:
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
Click to expand...
Click to collapse
hmm you sure? The dutty download page says -
Things to Know how about my ROMs:
* Radio 2.15 Recommended
* HSPL 2.08 Recommended
* HSPL 3.03 doesn't support 576 RAM enabled
But i'll try to flash a 3.03HSPL and find out what happens. I did flash 2.15.50.14 radio before i flashed the Dutty rom. But gonna give it one last try.
samsamuel said:
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.
Click to expand...
Click to collapse
Have tried two pc's now, both running Win7 32bit - its all we have now.
Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?
samsamuel said:
Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?
Click to expand...
Click to collapse
yeah HSPL2.08, HSPL3.03 and Radio is flashing just fine. The roms i have tried also flashes perfect its just will not boot afterwards. I can usually do a hardreset on it and it will boot one time. If you then shut it off and try to turn it on again it fails with the white HTC screen again.
I am toally clueless on what is wrong with it, so gonna try to figure out if we have some kind of warrenty left on it and get it switched over to another one.

[Q]Help: is this HD2 dead?

First, sorry if I post the kind of question that has been already asked 1000 times, I'll understand if my post is deleted.
here is the story: I still have an HD2, but got a Sensation almost one year ago.
Now my HD2 is still WinMo 6.5 with Android from the SD card.
Yesterday, one of my pupils (yes, I'm a teacher, and my pupils know I'm into smartphones....!) gave me his HD2 because his father kinda bricked it.
I haven't been using my HD2 or reading XDA HD2 section or a long time (I'm too busy flashing my Sensation, so reading Sensation threads ), but I thought I could give it a try to unbrick it, I'm not a noob after all (selfish guy!!!!!!!!!)
I think this HD2 was somehow bricked while trying to install Android into NAND, or installing MAGDLR, as far as my pupil can tell from his dad
So this Sensation can't boot and has this, written in the 3 colours screen
PB81100 HX-BC
SPL-2.08.00 8G XE
MicroP(LED) 0x05
icroP(TOUCH) 0x40
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
Here is the state I had this HD2, unable to boot, just able to get into bootloader with the message above.
I tried to flash latest Dutty ROM (because I was using Dutty creme of the creme at my HD2 time!)
=> through USB, flash freezes sometimes at 2%, sometimes 75%
=> through SD card: it flashes, says it's successful, but the device doesn't boot, back to three colors screen, or white screen with error message if trying to boot normally
I tried task29: full of errors, not better after flashing a ROM
I tried flashing a shipped "official" ROM => same as custom ROM, says success, flashed through SD card, but never boots to something else than 3 colors screen..
I tried factory reset, said successful, but still no boot!!
I tried flashing a Radio ROM=> flash successful, but still no boot
I tried flashing HSPL again, 2.08 and previous versions: it flashes OK, can see the changes in three colours screen, but no success flashing a ROM after
I noticed that sometimes, this HD2 vibrates 7 times quickly in a row, which my own HD2 had never done, and I suppose it's a very bad signal
I'm not a noob at all, but really can't follow every thread, and tried the search function with no real luck.
Is this HD2 definitly bricked? Is there something I can do?
Sorry again to seem so noob, I would have flammed someone posting like me, when I was following HD2 development everyday, before having my Sensation (and a Moto Defy for my wife)
see the line ''SPL-2.08.00 8G XE'' (you actually mean 2.08.0000) well teh .0000 tells you its NOT hspl, its a stock spl, so nothing will flash.
run hspl 2,3 or 4 and choose ''2.08.hspl''. Flashing, task29, magldr, all that will now flash.
THANKS!
how stupide I am (or too long away from WinMo)
I had tried hspl2 that was unable to do the job, hspl4 did it
So now I have spl 2.08.hspl
...but face other problem:
task29 fails: it launches OK but my HD2 disconnects from USB as soon as task29 starts its process
if I try to flash a custom ROM (the dutty one my own HD2 is still using), via usb, same, usb disconnects (it wasn't before I flashes hspl 2.08)
If I try flashing as a LEOIMG with microSD, it feezes at about 2/3 of the process
trying to flash a shipped ROM leads to errors, back to three colors screen with "Upgrade ROM code error Please try again"
...not to mention each time it replaces the hspl by stock spl
Any idea?
i900frenchaddict said:
THANKS!
how stupide I am (or too long away from WinMo)
I had tried hspl2 that was unable to do the job, hspl4 did it
So now I have spl 2.08.hspl
...but face other problem:
task29 fails: it launches OK but my HD2 disconnects from USB as soon as task29 starts its process
Click to expand...
Click to collapse
don't run flashes from running winmo, enter bootloader manually, when serial --> usb, run your flash/task29 or whatever. (Gorget about task29, it isnt necessary)
alternatively, if you do run it from running winmo, then once the phone has restarted and the usb has timed out, simply run teh flash program again, and dont touch teh phone, since it will now be in bootloader, and my above note takes over.
if I try to flash a custom ROM (the dutty one my own HD2 is still using), via usb, same, usb disconnects (it wasn't before I flashes hspl 2.08)
If I try flashing as a LEOIMG with microSD, it freezes at about 2/3 of the process
Click to expand...
Click to collapse
not a good sign, but ignore that for now.
trying to flash a shipped ROM leads to errors, back to three colours screen with "Upgrade ROM code error Please try again"
...not to mention each time it replaces the hspl by stock spl
Any idea?
Click to expand...
Click to collapse
because that's the way to remove hspl, , flash a stock rom from sd. Step 1 of sd flashing is the spl gets flashed, removing hspl, the phone then restarts and tries to flash the stock rom, but now that hspl has gone it fails, since you aren't using the correct stock rom for that particular phone.
Try this, get the stock 3.14 rom ( filename will be RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship )
EDIT - you dont have a tmous, right? if you do, dont do this!)
phone into bootloader
use hspl4 to set 3.03.hspl
phone into bootloader
flash the 3.14 rom over usb.
report back.
Man, I'm on the good way!
3.03.hspl seems to be the key, when 20.8hspl wasn't
While the stock 3.14 ROM finished to download, I could run a Task29 till the end, no more USB disconnecting.
Crossing fingers!
I'll edit this post once I've tried to flash the stock 3.14 ROM
Huge thanks to you !!!!
2.x spl is not a stock spl for regular hd2's, only tmous, so whilst it does work, it does introduce the odd problem. for example you cant sd flash stock roms with 1.x versions when you are currently on 2.x.
SO, with a regular hd2, any time you wanna return to stock or are having flashing troubles of some kind, it is always worth using hspl.exe (2,3 or 4 , doesnt matter) to remove the 2.x spl/hspl.
For me, I always go back to 1.66.0000 using hspl2 before i even try to flash a stock rom. Since i choose a 0000 ending, it will be updated as required by the stock rom.
Fingers crossed it helped.
samsamuel said:
Try this, get the stock 3.14 rom ( filename will be RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship )
EDIT - you dont have a tmous, right? if you do, dont do this!)
phone into bootloader
use hspl4 to set 3.03.hspl
phone into bootloader
flash the 3.14 rom over usb.
report back.
Click to expand...
Click to collapse
This worked for me...Thank you so much.

Categories

Resources