HD2 kinda broken what can i do? - HD2 General

Hey XDA
Hope someone out there have got some good advice. We have some HD2s where i work and i have been sent one that is acting kinda weird.
I simply can not get it to flash a rom (_HTC HD2_RUU_Leo_S_HTC_DAN_3.14.403.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship) - we only use normal HTC roms. When i try to flash it nothing happens, it boots into the bootloader and just sits there at 0% until i disconnect the cable, if i dont it will sit there untill it runs out of battery. Tried a few times now and same result.
i have also just tried a restore, to see if its the internal flash rom that is broken and the restore also fails. My own HD2 restores in like a few seconds but this one just sits there again, like when i try to flash a rom to it.
So is it totally dead or is there something i should try?

Have you tried to use task29 (via computer) , then flash (via nbh) the htc rom?

hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.

dkwolf said:
hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.
Click to expand...
Click to collapse
HSPL 2.08 & reflash original HTC ROM via PC USB.
Do you get any error codes from the flash utility ?
could be CID related but you should see error code.

Yes, trying it with HSPL seems like a good idea to me, too.
Because then you can also try other ROMs.

will try this stuff on monday - i just cba to do more work today
thx for the advice

Build a gold-card and flash from the SD slot. If that doesn't work, put it in a zip lock bag and then into the freezer for 10 minutes. After 10 minutes, boot the phone and try flashing again immediately in it's chilled state. If it get's ANY further, you have a bad overheating NAND and need a new main board.

got HSPL2.08 flashed and a Dutty 3.14 rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions in the bottom. So i am just gonna toss this one out, since its can not be serviced (supplier has gone bust).
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.

dkwolf said:
got HSPL2.08 flashed and a Dutty 3.14[/COLOR] rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions((edit - the RGD screen)) in the bottom.
Click to expand...
Click to collapse
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.
Click to expand...
Click to collapse
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.

samsamuel said:
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
Click to expand...
Click to collapse
hmm you sure? The dutty download page says -
Things to Know how about my ROMs:
* Radio 2.15 Recommended
* HSPL 2.08 Recommended
* HSPL 3.03 doesn't support 576 RAM enabled
But i'll try to flash a 3.03HSPL and find out what happens. I did flash 2.15.50.14 radio before i flashed the Dutty rom. But gonna give it one last try.
samsamuel said:
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.
Click to expand...
Click to collapse
Have tried two pc's now, both running Win7 32bit - its all we have now.

Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?

samsamuel said:
Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?
Click to expand...
Click to collapse
yeah HSPL2.08, HSPL3.03 and Radio is flashing just fine. The roms i have tried also flashes perfect its just will not boot afterwards. I can usually do a hardreset on it and it will boot one time. If you then shut it off and try to turn it on again it fails with the white HTC screen again.
I am toally clueless on what is wrong with it, so gonna try to figure out if we have some kind of warrenty left on it and get it switched over to another one.

Related

[q] help maglder fatal hit 1 error?? Phone won't boot?

phone was working fine up until yesterday it frooze up then resarted and magldr went go go go then fatal hit 1 after that. Tried restarting it but notthing seemed to help. I tried to reflash a winmo rom but that kept hanging at the htc screen tried task 29 reflashing custom and stock winmo roms but nothing seems to work phone still goes to the bootloader and still hspl anyone have any idea how to fix this i am stumped??
MAZDROID said:
phone was working fine up until yesterday it frooze up then resarted and magldr went go go go then fatal hit 1 after that. Tried restarting it but notthing seemed to help. I tried to reflash a winmo rom but that kept hanging at the htc screen tried task 29 reflashing custom and stock winmo roms but nothing seems to work phone still goes to the bootloader and still hspl anyone have any idea how to fix this i am stumped??
Click to expand...
Click to collapse
i got this a couple times made me freak out too
all i did is removed the battery and it worked afterwards
did u try flashing a new nand android?
Yea i did but i still kept getting the same error should i try a different nand rom?
and after i reinstall a new nand rom its gets the the "reset now!" and just sits there
MAZDROID said:
and after i reinstall a new nand rom its gets the the "reset now!" and just sits there
Click to expand...
Click to collapse
Try going to bootloader - hold vol. down and press and release the power button
Then try flashing radio, hspl.2.08 and then magldr 1.11
This might help
heck i tried reflashing the radio and the hspl and the magldr all of its goes fine until when i try to install a nand rom once i do that i gets all the way to the "reset now!" and just stays there at this point i just want to get a stock winmo rom back on so i can atleast make calls this phone is my only form of communication
MAZDROID said:
heck i tried reflashing the radio and the hspl and the magldr all of its goes fine until when i try to install a nand rom once i do that i gets all the way to the "reset now!" and just stays there at this point i just want to get a stock winmo rom back on so i can atleast make calls this phone is my only form of communication
Click to expand...
Click to collapse
What is your HSPL version ? Its written on the tricoloured screen of the bootloader ? Your phone was unlocked before you tried to flash a NAND ROM ?
Try and use a task29 tool provided here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 . Extract it and run it properly ( with phone in bootloader mode ) and perform the task 29. Then flash a radio version which you can find it here http://forum.xda-developers.com/showthread.php?t=611787 . ( I suggest 2.14.50.02 )
My suggestion is to go to bootloader-tricoloured screen ( NOT Magldr ). Flash a good radio version and afterwards go back to tricoloured screen of the bootloader in order to flash a Windows Mobile ROM ( preferably a STOCK one ). Forget about NAND ROMs until you will be sure what your problem is.
PS : Very very important read for 2-3 hours ( to understand well ) what says here http://forum.xda-developers.com/showthread.php?t=609477
viperd said:
What is your HSPL version ? Its written on the tricoloured screen of the bootloader ? Your phone was unlocked before you tried to flash a NAND ROM ?
Try and use a task29 tool provided here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 . Extract it and run it properly ( with phone in bootloader mode ) and perform the task 29. Then flash a radio version which you can find it here http://forum.xda-developers.com/showthread.php?t=611787 . ( I suggest 2.14.50.02 )
My suggestion is to go to bootloader-tricoloured screen ( NOT Magldr ). Flash a good radio version and afterwards go back to tricoloured screen of the bootloader in order to flash a Windows Mobile ROM ( preferably a STOCK one ). Forget about NAND ROMs until you will be sure what your problem is.
PS : Very very important read for 2-3 hours ( to understand well ) what says here http://forum.xda-developers.com/showthread.php?t=609477
Click to expand...
Click to collapse
thanks man i followed your instructions and i am now back into winmo thanks a million times
MAZDROID said:
thanks man i followed your instructions and i am now back into winmo thanks a million times
Click to expand...
Click to collapse
I am having the same problem.
@ MAZDROID: Can you tell me the steps you did to recover your phone?
Thanks a lot.
Are you using the stock usb cable that came with the phone or some generic one?
There seems to be slight corruption while you are flashing the ROM.
Try using memtest86+ and test your computer's RAM.
LiFE1688 said:
Are you using the stock usb cable that came with the phone or some generic one?
There seems to be slight corruption while you are flashing the ROM.
Try using memtest86+ and test your computer's RAM.
Click to expand...
Click to collapse
Thanks for reply. I did not use the stock usb cable, but it was the same with the factory usb cable.
I got this problem when tried to install WP7, then got "fatal hit 1 error" when booting WP7 for the 1st time.
Now my phone is bricked with T-mobile logo. Tried to HSPL, fash radio, flash OS (with the stock one) by task 29 many times, but it did not work. All flash process are okie, but My phone is still bricked
Any way to bring the phone to factory settings? Need help for an advise. Thanks a lot
Is your's one of those 1024MB ROM T-Mobile HD2s?
I am not sure if the the SD leoimg.nbh recovery method works. It flashes the SPL back to Original, including Firmware, and RADIO.
If your HD2 only has 512MB ROM, then just download the Official HTC HD2 ROM from HTC's support site (If it is UK, then select UK, if it is USA, you are kinda S.O.L.)
Extract the RUU(something).exe file using WinZIP or WinRAR or 7-ZIP.
There will be a RUU_signed.nbh file, rename that to leoimg.nbh and put that in the ROOT folder of your FAT16/FAT32 MicroSD Card.
While holding the Volume Down button, power up the device.
It should detect the LEOIMG.nbh file and flash everything back to default.
*WARNING*
Make sure your HD2 has 512MB ROM, NOT 1024MB ROM
Make sure your MicroSD Card is formatted in FAT32 or FAT16
Make sure the the Official RUU ROM is v1.xx and NOT v3.xx
Good Luck!
BTW: The Stock Cable seems to have a DIODE soldered to it. Regular cable is fine, but it doesn't protect it from current back flow during charging.
I started with a task29 then flashed a new radio and then I reloaded a stock rom via usb since i couldn't get it to work via sd card. I was able to get the phone to start but i still am running into problems when flashing in general with the phone on multiple computers so part of the problem was solved but every now and again it just shuts of and i have to reflash
LiFE1688 said:
Is your's one of those 1024MB ROM T-Mobile HD2s?
I am not sure if the the SD leoimg.nbh recovery method works. It flashes the SPL back to Original, including Firmware, and RADIO.
If your HD2 only has 512MB ROM, then just download the Official HTC HD2 ROM from HTC's support site (If it is UK, then select UK, if it is USA, you are kinda S.O.L.)
Extract the RUU(something).exe file using WinZIP or WinRAR or 7-ZIP.
There will be a RUU_signed.nbh file, rename that to leoimg.nbh and put that in the ROOT folder of your FAT16/FAT32 MicroSD Card.
While holding the Volume Down button, power up the device.
It should detect the LEOIMG.nbh file and flash everything back to default.
*WARNING*
Make sure your HD2 has 512MB ROM, NOT 1024MB ROM
Make sure your MicroSD Card is formatted in FAT32 or FAT16
Make sure the the Official RUU ROM is v1.xx and NOT v3.xx
Good Luck!
BTW: The Stock Cable seems to have a DIODE soldered to it. Regular cable is fine, but it doesn't protect it from current back flow during charging.
Click to expand...
Click to collapse
Thanks, but mine is 1024MB ROM T-Mobile HD2s. Now whatever I flash the phone, it is still bricking, so i think it would work if I removed HSPL and bring it to the default factory.
Any idea to do this?
MAZDROID said:
I started with a task29 then flashed a new radio and then I reloaded a stock rom via usb since i couldn't get it to work via sd card. I was able to get the phone to start but i still am running into problems when flashing in general with the phone on multiple computers so part of the problem was solved but every now and again it just shuts of and i have to reflash
Click to expand...
Click to collapse
I did task 29, then updated radio 2.14 for T-MOUS, but tri-color boot loader sill comes with HSPL 2.08 which means radio was still 2.08? Then I updated factory ROM ship (OS 3.4 and radio 2.14). I can not find a Rom with only OS (not including radio)
Did you get the change of radio to 2.14 in boot loader? Where to download a factory ROM with OS for T-MOUS?
Thanks
Well, this is the thing, T-MOUS controls the ROM releases. The deal they have with HTC refrains HTC from releasing or hosting any of the ROMs. So they should be hosted on T-mobile US website.
Anyways, from what I know, there are only 3 releases so far for US T-Mobile HD2
2.10.531.1
2.13.531.1
3.14.531.1 <--- DO NOT GET THIS ONE (Contains SPL 3.03 cannot be flashed to HSPL 2.08)
After you do a RECOVERY using the bootloader, you will have to reflash the radio to one that is compatible with Android, after that you reflash the radio to one that can be used by Android. Then you install MAGDLR.
I vaguely remember rumors that using a T-mobile will lock the phone to only T-mobile. If you have an sim unlocked T-Mobile, you might lock it again.
Please do so in that order.
BTW: If your phone still can get to the BootLoader (TRI COLOR SCREEN), it is not bricked, it is just not behaving. Bricked means you can't even turn it on for some people.
OMG, they are... LOL!
http://www.t-mobile.com/wmupgrade/
My phone just reborned now. Thought it was totally die when stucking with "stick together" logo. Here are the steps I did.
1) Redo exactly step by step in this post (focus on steps: HSPL, campatible ROM, hard-reset, remove/reinstall memory card + Sim)
http://forum.xda-developers.com/showthread.php?t=609477
2) Try with different SIM CARDS for your phone. I tried 5-6 ATT cards, and only 1 works and helps to go through stick together logo. If you see these words R G B at the bottom, then you phone revives.
SO happy now! Thanks all for your previous posts
No luck
I've tried everything but nothing.
I Get the "Fatal hit 1" when I'm trying to enter AD Recovery.
I'm not able to boot it with WM stock - it just get stucked att the first HTC screen.
Anyone has an idea on how to solve this?
I've have made a few steps several times but still nothing, starting to get frustrated.
Try to flash a different size partition of cwm, see if that will get you in clock work recovery...
Sent from my HTC HD2 using XDA App
kompheak said:
Try to flash a different size partition of cwm, see if that will get you in clock work recovery...
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
Thank you so so much! It worked!
This is how I did for you other guys how's experience the same issue.
I did all this with the HD2 Toolkit.
1. Wipe Task 29
2. Install HSPL 2.08 HSPL (Don't now if this is needed but did it anyway)
3. Install MAGLDR
4. MAGLDR Reperation with Partition 200MB Cache 8MB
Now I was able to enter AD Recovery and install zip from SD card.
Android is loading at the moment and now it started up!
Thanks once again!

[Q] Possible Brick?? Some help if possible

Hey Guys,
I have NFI what happened to my phone but I think its bitten then dust..
I've been running NAND Android builds for a while now, the phone has been a bit funky for a few weeks now so I wanted to completely wipe and start form scratch..
So I download Task29 a new radio and ROM from the links in the ROM page (http://forum.xda-developers.com/showthread.php?t=933951) and ran Task29 like I have multiple times before.
The install went fine, and the phone rebooted like its meant to but now its stuck on the HTC screen, I can't boot in MAGLDR or HSPL...
So, is it borked??
suitable radio? suitable spl? both are critical. magldr wont work without 2.08.hspl and a ..50.. radio
samsamuel said:
suitable radio? suitable spl? both are critical. magldr wont work without 2.08.hspl and a ..50.. radio
Click to expand...
Click to collapse
The radio that was installed on before running TASK29 was, Radio Leo 2.15.50.14.
It already had HSPL v2.08 and MGLDR 1.3, already installed.
As I said, I've flashed new WinMo and Android ROM's hundreds of times, I mean I dont normally run Task29 before every install but I have multiple times in the past.
I only ran Task29 today as the phone was being really bad so I though a clean install might be the best way to go.
hmm, not sure what to suggest without sounding patronising, hehe,
there are a few people that cant seem to get magldr to start, for no good reason,
reflash the radio (just in case) manually go check the spl in bootloader again (just in case it doesnt say 2.08.hspl,, sometimes what you know for a fact is true actually isnt) and as for magldr, well its susceptible to all the usual flashing issues, , run as administrator, try every usb port, turn off your firewall,,,, try another pc even, , in fact if you have another pc available, try that first.
Thanks for the replies, but I can't get it to boot into MGLDR or SPL thats my problem.
When I turn it on it loads up the 1st HTC logo and hangs.
Is there another way that I can flash a radio of I cant boot into SPL???
I've read something about this before. I don't think it's an easy fix and it may be best to try go back to where you bought it and try get a replacement or send it in to HTC. I'm not too sure if they'll know that you have HSPL installed. I'd say highly likely they will. Have you tried hard resetting? Or can you not get to that screen?
If you want to find more on this just google "HD2 Wsod" or "HD2 White screen of death". You'll find lots if people with the same thing.
My HD2 has something similar but I can get to HSPL but it stays at a blank white screen with normal power on.
What happens when it's off snd you plug in the USB? Does it try start because of MAGLDR or just charge/do nothing?
Skellyyy said:
What happens when it's off snd you plug in the USB? Does it try start because of MAGLDR or just charge/do nothing?
Click to expand...
Click to collapse
Thanks for the reply, when I plug the USB cable in while the phone is off, only the charge light comes up. Doesn't actually try and boot
QuazzieM said:
Thanks for the replies, but I can't get it to boot into MGLDR or SPL thats my problem.
When I turn it on it loads up the 1st HTC logo and hangs.
Is there another way that I can flash a radio of I cant boot into SPL???
Click to expand...
Click to collapse
I know you said you ha e flashed hundreds of times, so you should know this. I am not being patronizing here either, but I will say it anyway. You have gwo different ways to flash a new radio, but both require gou to put gour HD2 into bootloader.
To put your HD2 into bootloader turn the device off and then turn it back on but hold the volume down button wbile it is booting and it will go to bootloader.
Whilr jn bootloader connect via USB cable to gour computer wait until you see USB the wbite bar of bootloader then you can flash the radio, a Win Mo ROM, HSPL, or MAGLDR just wich ever one uou want to flash at that time.
You can use a 500MB to 4GB SD card to flash the radio as well as a Win Mo ROM. You just rename the.nbh file to leoimg.nbh for the radio or the ROM and copy it to the root of your SD card. plasce the SD card back in the device. Put the device into bootloader but do not let go of the volume down botton until you see search hinge on the screen of the device. Be aware though if you flash a official ROM this way it will overwrite everything HSPL and all so you whind up with a stock HD2 again.
Stupid question: you are holding down the volume down button to boot into HSPL right?

[Q] Flashing Problem

Hi all,
I would like to ask someone who are willing to lend me a hand.
Here comes the problem:
1. I wanna flash a NAND Android into my HD2 (not Tmous)
2. I have already flashed with HSPL2 with selection of 2.08 HSPL.
3. It went through to Windows Mobile again, nothing goes wrong untill when I am trying to flash with Magldr Bootloader with ROM Update Utility.
4. It went through again, after that the phone reboot itself and it should be displaying Magldr bootloader instead of HTC green logo stuck at the WHITE SCREEN.
5. I've tried several ways to solve it including soft-reset but still nothing happen with the same problem which is the green HTC logo stuck at the white screen.
6. Even Hard-reset with factory default reset I have tried, the process went through, but still the same problem again (YOU GUYS KNOW WHAT I MEANT).
7. So, I tried another LeoAdvanceRUU.exe which @HD2Owner had posted few months ago, the flashing process worked through but it stucked at the 0% with HTC logo at BLACK screen.
8. I kept on trying with another ROM or Radio Flashing again, again and again and it is still stucked at 0% !!! (GOSH !! I'm going to be crazy)
I really hope someone can help me out of this as I am very appreciate to those who are willing to help me. I need the phone to deal with my daily usage, please the 'PRO's out there.. ><
Thanks in advance.
P/S: The Tri-Color mode showed PB8100 - SS-BC
Did bootloader show 'SPL2.08HSPL' (or something along those lines)?
Nigeldg said:
Did bootloader show 'SPL2.08HSPL' (or something along those lines)?
Click to expand...
Click to collapse
Yes !! It does showed..coz its already HSPL-ed..but i stil duno what is happening..
you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start
I dont drink either LOL
samsamuel said:
you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start
Click to expand...
Click to collapse
erm, I also tried to Flash the Radio ROM, but it will stucked at HTC logo with Black Screen and also 0% wont move either..
In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)
samsamuel said:
In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)
Click to expand...
Click to collapse
yea i did install the HSPL before flashing the radio and it is done with 2.08 HSPL
but what do u mean by Radios news HSPL?
when I am flashing the radio in the bootloader, I used the common flashing technique which is using the CustomRUU with the RUU_Signed.nbh file which contains Radio 2.14.50 and then the only the problem came out.
by means every ROM that I am trying to flash, It will still stuck at 0% Black Screen with HTC logo..
oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.
samsamuel said:
oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.
Click to expand...
Click to collapse
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??
no, no usb needed, put the leoimg on the sd card, card into phone, power on phone holding voldown, bootloader finds the leoimg on the card and starts the flashing process.
eXcMichael said:
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??
Click to expand...
Click to collapse
OK THAT'S WORKING @samsamuel !!!!!
THANKS ALOT !!!
I also assume the Radio was not flashed but i just cannot find a way to do the flash, and my troubleshooting was correct.
THANKS ALOT especially @samsauel and other devs' assistance. Highly Appreciate for what you guys contributed.. really THANK YOU, ITS NOW RUNNING Hyperdroid GBX ~
Thread can be closed and for further reference.
Look for HD2 nand toolkit 4.1 on XDA developers
It's a all in one utility hand HD2.
You can also try the we site addictive tips.com , they step by step tutorials.

[Q]Help: is this HD2 dead?

First, sorry if I post the kind of question that has been already asked 1000 times, I'll understand if my post is deleted.
here is the story: I still have an HD2, but got a Sensation almost one year ago.
Now my HD2 is still WinMo 6.5 with Android from the SD card.
Yesterday, one of my pupils (yes, I'm a teacher, and my pupils know I'm into smartphones....!) gave me his HD2 because his father kinda bricked it.
I haven't been using my HD2 or reading XDA HD2 section or a long time (I'm too busy flashing my Sensation, so reading Sensation threads ), but I thought I could give it a try to unbrick it, I'm not a noob after all (selfish guy!!!!!!!!!)
I think this HD2 was somehow bricked while trying to install Android into NAND, or installing MAGDLR, as far as my pupil can tell from his dad
So this Sensation can't boot and has this, written in the 3 colours screen
PB81100 HX-BC
SPL-2.08.00 8G XE
MicroP(LED) 0x05
icroP(TOUCH) 0x40
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
Here is the state I had this HD2, unable to boot, just able to get into bootloader with the message above.
I tried to flash latest Dutty ROM (because I was using Dutty creme of the creme at my HD2 time!)
=> through USB, flash freezes sometimes at 2%, sometimes 75%
=> through SD card: it flashes, says it's successful, but the device doesn't boot, back to three colors screen, or white screen with error message if trying to boot normally
I tried task29: full of errors, not better after flashing a ROM
I tried flashing a shipped "official" ROM => same as custom ROM, says success, flashed through SD card, but never boots to something else than 3 colors screen..
I tried factory reset, said successful, but still no boot!!
I tried flashing a Radio ROM=> flash successful, but still no boot
I tried flashing HSPL again, 2.08 and previous versions: it flashes OK, can see the changes in three colours screen, but no success flashing a ROM after
I noticed that sometimes, this HD2 vibrates 7 times quickly in a row, which my own HD2 had never done, and I suppose it's a very bad signal
I'm not a noob at all, but really can't follow every thread, and tried the search function with no real luck.
Is this HD2 definitly bricked? Is there something I can do?
Sorry again to seem so noob, I would have flammed someone posting like me, when I was following HD2 development everyday, before having my Sensation (and a Moto Defy for my wife)
see the line ''SPL-2.08.00 8G XE'' (you actually mean 2.08.0000) well teh .0000 tells you its NOT hspl, its a stock spl, so nothing will flash.
run hspl 2,3 or 4 and choose ''2.08.hspl''. Flashing, task29, magldr, all that will now flash.
THANKS!
how stupide I am (or too long away from WinMo)
I had tried hspl2 that was unable to do the job, hspl4 did it
So now I have spl 2.08.hspl
...but face other problem:
task29 fails: it launches OK but my HD2 disconnects from USB as soon as task29 starts its process
if I try to flash a custom ROM (the dutty one my own HD2 is still using), via usb, same, usb disconnects (it wasn't before I flashes hspl 2.08)
If I try flashing as a LEOIMG with microSD, it feezes at about 2/3 of the process
trying to flash a shipped ROM leads to errors, back to three colors screen with "Upgrade ROM code error Please try again"
...not to mention each time it replaces the hspl by stock spl
Any idea?
i900frenchaddict said:
THANKS!
how stupide I am (or too long away from WinMo)
I had tried hspl2 that was unable to do the job, hspl4 did it
So now I have spl 2.08.hspl
...but face other problem:
task29 fails: it launches OK but my HD2 disconnects from USB as soon as task29 starts its process
Click to expand...
Click to collapse
don't run flashes from running winmo, enter bootloader manually, when serial --> usb, run your flash/task29 or whatever. (Gorget about task29, it isnt necessary)
alternatively, if you do run it from running winmo, then once the phone has restarted and the usb has timed out, simply run teh flash program again, and dont touch teh phone, since it will now be in bootloader, and my above note takes over.
if I try to flash a custom ROM (the dutty one my own HD2 is still using), via usb, same, usb disconnects (it wasn't before I flashes hspl 2.08)
If I try flashing as a LEOIMG with microSD, it freezes at about 2/3 of the process
Click to expand...
Click to collapse
not a good sign, but ignore that for now.
trying to flash a shipped ROM leads to errors, back to three colours screen with "Upgrade ROM code error Please try again"
...not to mention each time it replaces the hspl by stock spl
Any idea?
Click to expand...
Click to collapse
because that's the way to remove hspl, , flash a stock rom from sd. Step 1 of sd flashing is the spl gets flashed, removing hspl, the phone then restarts and tries to flash the stock rom, but now that hspl has gone it fails, since you aren't using the correct stock rom for that particular phone.
Try this, get the stock 3.14 rom ( filename will be RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship )
EDIT - you dont have a tmous, right? if you do, dont do this!)
phone into bootloader
use hspl4 to set 3.03.hspl
phone into bootloader
flash the 3.14 rom over usb.
report back.
Man, I'm on the good way!
3.03.hspl seems to be the key, when 20.8hspl wasn't
While the stock 3.14 ROM finished to download, I could run a Task29 till the end, no more USB disconnecting.
Crossing fingers!
I'll edit this post once I've tried to flash the stock 3.14 ROM
Huge thanks to you !!!!
2.x spl is not a stock spl for regular hd2's, only tmous, so whilst it does work, it does introduce the odd problem. for example you cant sd flash stock roms with 1.x versions when you are currently on 2.x.
SO, with a regular hd2, any time you wanna return to stock or are having flashing troubles of some kind, it is always worth using hspl.exe (2,3 or 4 , doesnt matter) to remove the 2.x spl/hspl.
For me, I always go back to 1.66.0000 using hspl2 before i even try to flash a stock rom. Since i choose a 0000 ending, it will be updated as required by the stock rom.
Fingers crossed it helped.
samsamuel said:
Try this, get the stock 3.14 rom ( filename will be RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship )
EDIT - you dont have a tmous, right? if you do, dont do this!)
phone into bootloader
use hspl4 to set 3.03.hspl
phone into bootloader
flash the 3.14 rom over usb.
report back.
Click to expand...
Click to collapse
This worked for me...Thank you so much.

[Q] Tmous or Eu? need help

Dear Dev's / members
I have problem with this HD2 and cannot find a solution yet!
first thing first. is this a Tmobile of Eu mobile?
i tried flashing factory RUU but after 1% it gives an error saying Radio failed.
tried flash quite a few radio's but still after 100% it says radio fail.
tried flashing from USB cable
tried flashing from SD with leoimg.nbh
no luck.
the guy was using android on it until yesterday. may be he tried to flash a wrong Rom which brick the phone. now only white screen appears.
i can go to bootloader mode but no luck in flashing any thing at all.
Looks like EU model as no logo near earpiece.
if also has white markings on call & end key that would help confirm EU.
If trying to install .nbh file from SD it will overwrite HSPL so check current SPL status in bootloader.
If still on HSPL 2.08 try flashing an NRG WM6.5 ROM & see what happens (they have no radio so if completes then try radio flash if needed, try via USB them SD if USB fails.
Do you get an error code when it fails via RUU ?
thanks for helping mr. B
the error i get is (270) and yes it have white markings on all the buttons. so its confirm EU model. by NRG rom you mean Energy Roms? i tried earlier the energy Rom but no luck. after 1% it gives error.
cannot try mtty method as i'm on windows 7 and in windows 7, it's not showing the USB port. it's radio is corrupted. i think someone must have flashed a wrong Rom.
What standard ROM have you got ? if it a 3.14 rom try connecting HD2 via USB & use HSPL4 toolkit to install HSPL 3.03 & if that installs then try the 3.14 ROM via USB & RUU.
Also eliminate simple issues such as lead & USB port by switching port & using a different USB lead.
Windows 7 64bit ? worth trying another PC & 32bit if can as WMDC drivers on 64bit can be a pain for flashing ...
windows 7 32bit. tried flashing hspl 4 and it says complete but in bootloader it shows 2.08 only. i guess gold card method will solve the problem but it's too complicated. any other suggestions?
i would search for task29 and format the phone back to virgin default then download a windows rom from htc via the downloads page on there website for the phone ,then if it works re task29 it then put android on it with the htc hd2 tool kit witch has every thing other than rom (all u need to do is task29 it then go back to the boot loader and run the ruu rom)
samuel79 said:
i would search for task29 and format the phone back to virgin default then download a windows rom from htc via the downloads page on there website for the phone ,then if it works re task29 it then put android on it with the htc hd2 tool kit witch has every thing other than rom (all u need to do is task29 it then go back to the boot loader and run the ruu rom)
Click to expand...
Click to collapse
No do not run a Task 29 the device. I say this for two reasons, one if you flash the Stock Windows Mobile ROM via RUU the RUU will run a Task 28 before installing the ROM witch is pretty much the same as a Task 29. The second reason is that if you run a Task 29 it will remove the current ROM on the device so it will not have a working ROM anymore. If after the Task 29 you can not get another ROM installed on it the you will not be able to use the device at all anymore.
why not he thinks its bricked so there is no difference if he cant get a rom on it
samuel79 said:
why not he thinks its bricked so there is no difference if he cant get a rom on it
Click to expand...
Click to collapse
No the device is not bricked, a bricked device will not even turn on at all, no vibrations no nothing.
At jacktackle, try to find the earliest stock Rom RUU for your HD2 and try to flash it. It is possible you have what is reffered to as a stuck radio.The only fixI have seen for this is to flash a older ROM version with a older SPL version. If the earliest ROM version does not work start working your way up one version at a time and you might get lucky and get one that will flash.
thanks for all the help guys. but nothing worked. tried flashed old ruu's but reboots at 1% this radio is screwed up. hspl 2.08 is not upgrading nor downgrading. sd card update not working. i guess thats it. will give it back to him so that he can showcase it
first time ever i'm un successful. bad luck! may this LEO rest in peace. 'amen'
jacktackle said:
thanks for all the help guys. but nothing worked. tried flashed old ruu's but reboots at 1% this radio is screwed up. hspl 2.08 is not upgrading nor downgrading. sd card update not working. i guess thats it. will give it back to him so that he can showcase it
first time ever i'm un successful. bad luck! may this LEO rest in peace. 'amen'
Click to expand...
Click to collapse
Before you give it back you can find some of the old test ROMs for the EU or for the TMOUS depending on which version of the HD2 it is. Just make sure if it is a TMOUS that you do not flash a rom version that has a 51 radio with it. Just look at the RUU name and the radio version is in the name. If that does not work then the only fix will be to replace the mainboard cause JTAG would not fix the problem.

Categories

Resources