Database Users

Rom Flashing Help

So, I have installed HSPL 2.08. I flashed ChuckyDroid and it worked fine but I wanted more. So I flashed an Omega rom and it was cool but now I want to Flash Magldr1.3 and try wm7 or a nand android. The problem I am having is, when I start to flash the new rom, I get the HTC screen and 0% and it stays there forever. I end up pulling the battery and resetting the phone. I first tried with Mgldr then a few other wm6.5 roms with the same problem. Why can't I flash roms anymore?
I searched the thread and had no luck. I apologize in advance ir this has been covered before.

Try to flash stock Rom from tricolor or even from Your microSD card. And then hspl, magldr etc.

AzOutlaw said:
So, I have installed HSPL 2.08. I flashed ChuckyDroid and it worked fine but I wanted more. So I flashed an Omega rom and it was cool but now I want to Flash Magldr1.3 and try wm7 or a nand android. The problem I am having is, when I start to flash the new rom, I get the HTC screen and 0% and it stays there forever. I end up pulling the battery and resetting the phone. I first tried with Mgldr then a few other wm6.5 roms with the same problem. Why can't I flash roms anymore?
I searched the thread and had no luck. I apologize in advance ir this has been covered before.
Click to expand...
Click to collapse
How about this way.
Assuming you still can reach Boot Loader and You still have SPL 2.08 HSPL installed.
Go into bootloader screen and connect your phone using usb, and let the word: "serial" in the below of phone (the white color bar) changed to: "USB". If you fails, retry it using different ports, and dont forget to turn off your antivirus, firewall and internet connection, or even your screen saver.
While in bootloader, do "task 29", flash radio 2.15.xxx, install magldr 1.13 (all in sequence).
Assuming you succeed it. Now, we go into flashing NAND WP7 (or NAND Android).
Assuming that you already have NAND WP7 (or NAND ANDROID).
Go into magldr screen, you know how to do it right?
There, select option 5 (USB Flasher) and confirm it by pressing the phone call (green) button and connect your phone using usb to pc.
Run your NAND WP7 (or NAND ANDROID) rom.
Finish.
Good luck

[Q] Bricked?

So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.

Try to flash WM 6.5 1.66 version (or atleast the one below the most recent) trough SD method.
My kid brother had the same thing, the newest ROM (from HTC website) didnt work cause it gave a error.
If you keep getting some red error status while doing the SD flash, it might be bricked.
After a few tries with the SD method we were able to flash stock spl and such, but still the phone wasnt oke (but oke enough to send it for repair).

Skellyyy said:
So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.
Click to expand...
Click to collapse
hope this helps
http://forum.xda-developers.com/showthread.php?t=591314
http://forum.xda-developers.com/showthread.php?t=668347
dont forget to click thanks

Lol, guys all I did was hold down the reset button on the back and it turned back on. HAPPY!
Though, I want to run a Task 29 but it's still stuck at zero.
Oh well, I have a working HD2!

Skellyyy said:
Though, I want to run a Task 29 but it's still stuck at zero.
Click to expand...
Click to collapse
Because you don't have hspl you removed it by SD card stock flash.

samsamuel said:
Because you don't have hspl you removed it by SD card stock flash.
Click to expand...
Click to collapse
I didn't flash the stock ROM. I didn't do anything, just held the red button in. It keeps acting up now. Think it's time to sell and buy a new one.

Skellyyy said:
I didn't flash the stock ROM. I didn't do anything, just held the red button in. It keeps acting up now. Think it's time to sell and buy a new one.
Click to expand...
Click to collapse
really? I think you did...
Skellyyy said:
So guys I need help! I can't boot my phone! I can boot in to HSPL but that's about it. I can't boot in to MAGLDR. I tried running a Task29 but it just stays at 0%.
I've tried flashing MAGLDR and it's the same as the Task29... stays at 0%. Has my phone been bricked? Any help appreciated. I've tried flashing a stock ROM from SD and renaming the .nbh to LEOIMG.nbh but the first time I did it and it says to press power to confirm you want to flash it the phone just rebooted to the WSOD. Seems as though that changed my HSPL to HSPL.2.08.0000 now too instead of .HSPL. now all I get when I have the SD card in and boot to HSPL then when it boots to the grey coloured screen it just says "Loading...".
Is there anyway I can get my phone working again? Thanks.
Click to expand...
Click to collapse
Just so you know, when you start a stock rom sd card flash, the first thing it does is reset the spl, THEN it tries to flash the rom, two seperate events, (the phone even restarts in some instances between changing spl and starting the rom flash) so even if the flash fails, or doesnt even start, theres a good chance spl has already been removed.
(side note for info - This situation is most likely to happen when flashing stock from sd card when hspl is installed, because the rom doesnt get rejected at first because hspl is there, but after the spl is reset and teh phone reenters bootloader, it no longer accepts the rom, because hspl is gone, so the phone is temporarily locked up with no hspl and no working rom.)
So, you now have stock spl 2.08.0000 and a non working rom.
enter bootloader,
run hspl (new hspl4 link in my sig)
choose 2.08.hspl
re enter bootloader
flash magldr (just to be sure its there)
if you need to, make sure your radio is high enough version (if you have tmous forget this, if its a regular it needs to be in the 2.10.50 or so version or higher)
from power off, start the phone, as the very first splash screen changes to the black magldr screen, start pressing power, untill the menu items appear.
Job done.
Oh and the line "....I have the SD card in and boot to HSPL ......" makes no sense. You are booting to bootloader. its still bootloader whether it has spl or hspl. Your terminoligy will confuse you.

Well I highly doubt I did. Maybe it just updated the HSPL but that's all. Didn't even get rid of MAGLDR on my phone! When I held in the reset button, it booted straight to MAGLDR.
Maybe mine was just a fluke!

lol thats what i said, in a long winded way. when you run an sd card flash the first three or four seconds it loads the spl from the rom on the sd card, thus removing hspl.
(or in your incorrect words 'Maybe it just updated the HSPL but that's all' - correct, it 'updated' HSPL back to stock SPL)
but hey,its sorted, so no problem.

It's still HSPL though? It's just the previous version that's .0000 instead of .HSPL or am I completely off? Do I need to flash HSPL.2.08.HSPL again or can i just keep it .0000?

Lol I'm stupid. Sorry, realise now what you're saying now that I've looked at the SPL properly. So do you suggest I flash HSPL now?
Sent from my FutureShocks HD2 MIUI using XDA App

Lol,
One simple rule...
If it ends 0000 it is STOCK
If it ends .hspl it is hspl
Yes, run hspl.exe again, choose 2.08.hspl

Haha well atleast I've learned now. I don't even read the first part which just said SPL. Fail. If I flash HSPL again do I need to flash MAGLDR again?
Sent from my FutureShocks HD2 MIUI using XDA App

possibly, cos teh same sd card flash that wiped hspl could have also removed the second splash screen memory area, which is where magldr lives. deopends how far thru the flash it got before it stopped.
easy to tell tho, let it boot, if you see the black magldr screen appear when the first boot screen vanishes,, quickly press power and it will stop there and show the magldr menu, if it hangs without showing teh magldr screen, magldrs not there, and you pull the battery, into bootloader, flash magldr.

samsamuel said:
Lol,
One simple rule...
If it ends 0000 it is STOCK
If it ends .hspl it is hspl
Yes, run hspl.exe again, choose 2.08.hspl
Click to expand...
Click to collapse
agree! absolutely right

Erm well after the white HTC screen I get the MAGLDR screen that boots to my NAND ROM. I pressed the power button while it was booting but nothing happened.

Skellyyy said:
It's still HSPL though? It's just the previous version that's .0000 instead of .HSPL or am I completely off? Do I need to flash HSPL.2.08.HSPL again or can i just keep it .0000?
Click to expand...
Click to collapse
You will still need 2.08.hspl if you want to reinstall or update your magldr version at some stage. It wont work on 2.08.0000.

Skellyyy said:
Erm well after the white HTC screen I get the MAGLDR screen that boots to my NAND ROM. I pressed the power button while it was booting but nothing happened.
Click to expand...
Click to collapse
Sounds to me like you arent rpessing quick enough. keep holding power from the moment you power on if it helps.
the instructions are to hold power (end key) right from turning on until magldr menu appears, but for me, i watch the first splash screen, and just before it ends (6-7 seconds) only then do i press and hold the end key. do not let go of the end key until teh menu appears, else it will continue to boto the rom.

Oh so all you wanted to know is if I can boot to MAGLDR menu? Yeah, I can lol.

Wait a minute, you can't have MAGLDR unless you have HSPL (HSPL3 2.08) if you have just reflashed HSPL, That means you still don't have MAGLDR, unless you have flashed it already in which case you still don't have a working ROM (Android or Windows 7) until such time you chose an Android or Windows 7 build. confusing?
Here is the sequence of flash events.
1. HSPL3 - 2.08HSPL
2. MAGLDR 1.13
3. Flash your chosen ROM.

HD2 kinda broken what can i do?

Hey XDA
Hope someone out there have got some good advice. We have some HD2s where i work and i have been sent one that is acting kinda weird.
I simply can not get it to flash a rom (_HTC HD2_RUU_Leo_S_HTC_DAN_3.14.403.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship) - we only use normal HTC roms. When i try to flash it nothing happens, it boots into the bootloader and just sits there at 0% until i disconnect the cable, if i dont it will sit there untill it runs out of battery. Tried a few times now and same result.
i have also just tried a restore, to see if its the internal flash rom that is broken and the restore also fails. My own HD2 restores in like a few seconds but this one just sits there again, like when i try to flash a rom to it.
So is it totally dead or is there something i should try?

Have you tried to use task29 (via computer) , then flash (via nbh) the htc rom?

hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.

dkwolf said:
hmm just tried task29 and it did nothing, it booted the phone to the bootloader but no progress screen did show up. Tried it again and the phone just shut off again after showing the bootloader for a few seconds.
beginning to think this phone is toast.
Gonna try a HSPL update later and just flash a non HTC rom to see if that works.
Click to expand...
Click to collapse
HSPL 2.08 & reflash original HTC ROM via PC USB.
Do you get any error codes from the flash utility ?
could be CID related but you should see error code.

Yes, trying it with HSPL seems like a good idea to me, too.
Because then you can also try other ROMs.

will try this stuff on monday - i just cba to do more work today
thx for the advice

Build a gold-card and flash from the SD slot. If that doesn't work, put it in a zip lock bag and then into the freezer for 10 minutes. After 10 minutes, boot the phone and try flashing again immediately in it's chilled state. If it get's ANY further, you have a bad overheating NAND and need a new main board.

got HSPL2.08 flashed and a Dutty 3.14 rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions in the bottom. So i am just gonna toss this one out, since its can not be serviced (supplier has gone bust).
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.

dkwolf said:
got HSPL2.08 flashed and a Dutty 3.14[/COLOR] rom but phone refuses to reboot sometimes and boot just shows the white HTC background and does not show the radio/os versions((edit - the RGD screen)) in the bottom.
Click to expand...
Click to collapse
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
But still havn't gotten any error codes from the phone or flash programs, other then "USB connection failed". So i think its nand is kinda broken now.
Click to expand...
Click to collapse
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.

samsamuel said:
first, you can't run 3.14 roms on anything except spl 3.03.0000 or 3.03.hspl
Second it isn't booting because it almost certainly needs an updated radio, 2.15.50 for instance. You probably still have a 2.xx.51 from the original stock, and so wont show rgd screen till you change radio, won't run smoothly till you correct the spl with hspl4
Click to expand...
Click to collapse
hmm you sure? The dutty download page says -
Things to Know how about my ROMs:
* Radio 2.15 Recommended
* HSPL 2.08 Recommended
* HSPL 3.03 doesn't support 576 RAM enabled
But i'll try to flash a 3.03HSPL and find out what happens. I did flash 2.15.50.14 radio before i flashed the Dutty rom. But gonna give it one last try.
samsamuel said:
Put phone into bootloader manually, don't use front mounted USB ports, be sure and update win mo dev center to latest ver ..... all the usual USB connection error advice. Trying another PC with a different windows variant often helps if its available.
Click to expand...
Click to collapse
Have tried two pc's now, both running Win7 32bit - its all we have now.

Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?

samsamuel said:
Ahhh gitcha, then the dutty rom mustnt be 100% 3.14 rom (I didn't check) it must use a 2.x base to enable 576ram.
In which case, if stock roms don't flash but custom did, it could be stuck radio syndrome, which you can test for with (correct, get it using your serial from HTC.com) stock rom flash from sd card (4gb or smaller, fat32). Look out for "rsa radio fail" or similar on screen.
Edit, oh you said you flashed a radio, and that went ok?
Click to expand...
Click to collapse
yeah HSPL2.08, HSPL3.03 and Radio is flashing just fine. The roms i have tried also flashes perfect its just will not boot afterwards. I can usually do a hardreset on it and it will boot one time. If you then shut it off and try to turn it on again it fails with the white HTC screen again.
I am toally clueless on what is wrong with it, so gonna try to figure out if we have some kind of warrenty left on it and get it switched over to another one.

[Q][HELP!] Cant install MAGLDR

Hello, i have serious problem,
I was running Android GINGER... and after one restart i god 1234.... FAILED bla bla
After that i went to MAGLDR and tryed to reflash another rom but no succes
MAGLDR froze!!!!
I did TASK 29 on it and it removed everything, after this i am UNABLE to install MAGLDR 133 or any other on my HD2. its a 576MB from UK, using it in CROATIA.
HAD T-mob WIN 6.5, Android 2.1, and above mentioned 2.3.3 ver.
ANY IDEA HOW TO INSTALL MAGLDR AGAIN???
HSPL is COTULLA 2.08 HSPL
Did i bricked it? can i undo?
p.s. i did hardreset, didnt work.
CAN I TRY RETURN SPL and how to return to stock so i can try WMO6.5 again?
HELP i am desperate! help, payed alot for this phone, i am broke now without phone!

calm down man we've all been there at some point,
ok if you wanna go back to stock go to the htc site and download a official rom,
does your phone turn on?
can you get in bootloader?
if you can does it say spl or hspl ??

ops
i am sure you havent been there.
I GOT HSPL 2.08 by beppe and Cotula
I,ve tryed official rom, it starts counting, but at approx 10% it stops and bar goes red, and triangle with exclamation point appears next to it.
I OFF:... F**** it UP. i am so screwd!
-phone does turn on, and goes to white screen, saying htc and nothing
-i can go to 4colour bootscreen, sayes SERIAL and USB after i connect
ty for trying to help me

white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.

Demon_man said:
white screen hhmm Radio - do you happen to know what radio you have flashed, if not go here http://forum.xda-developers.com/showthread.php?t=611787 chose say 2.15.50.14 down load it, i dont have micro usb on my phone no more so you have to options put phone in bootloader wait for it to turn to usb and run the ruu for the radio, or extract it find the .nbh file and rename it to LEOIMG.nbh pop it in the phone keep holding volume down till u get a grey screen and follow the instructions to flash the radio, and then try again,
you said you had android before? did you use cwm or clk so you can recover??
oh and by the way i nearly bricked my hd2 on release day so i no how u feel lol
EDIT = you can try and flash the stock rom and start again, by using 7zip to extract the official rom, find the .nbh file, rename it to LEOIMG.nbh also pop it on a micro sd card smaller than 8gig (just to be safe) boot into bootloader and follow through that way.
Click to expand...
Click to collapse
i sayed i had android on cwm, i tryed recover but magldr crashed, and since then i have problem loading MAGLDR.
RADIO FAILED TO UPDATE, i tryed that version that you sayed but it goes to 100% then shows again that triangle with !inside. F***** i am loseing my mind!
Your way of upgrading rom wont work, gray screen shows for a glich of a second and dissapears to 4colour bootscreen.
I wish i died! i ****ed all up.
BTW i bought a phone in uk and on the back of battery sayes only serial numbers in this order:
S/N99HJY005-2
35412003-754967-0
no imei, no nothing else if helps.
i am dead, payed 500$ for it last year for this amazeing phone and now i ruined everything.

ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?

Demon_man said:
ok im with you on what you have and havent done, to me it sounds like a hardware problem if it wont flash, do you have another micro sd car you could use to try and go back to stock??
did you format the sd card first ?
Click to expand...
Click to collapse
I get it , how to do GRAY FLASHING THING, but i got RADIO EROOR
SAYES:
00018003
LEOIMG.nbh - FAIL
RADIO_V2 - RSA Fail
Update Terminate
UPDATE FAIL
this happends when the bar gets to the 100%

do you have access to another pc mate with a different operating system from yours??
are you connecting phone via usb to the front or back of the pc?
have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084

Take out the battery and keep the phone off in a very cool air conditioned room for a couple hours (maybe even the refrigerator).
Put the battery back in and flash stock again.
edit: hmm. Just read that other thread, yeah you may need to jtag it...but I'd still try the fridge thing.
Edit2: worked for this guy:
nschoot said:
Sorry, for not replying before...
I put my phone in a ziplock plastic back and left it in the fridge for a few hours (I think about 8 hours or so). Then I booted it and tried to install the LEOIMG.nbh file from SD card... I kept it in the fridge while installing the image.
And somehow, it just worked first time!!
The image (from the first post of this thread) is a US demo version of Windows mobile, but I was able to install the regular ROM from the HTC site after this - without the need to keep it in the fridge.
Click to expand...
Click to collapse

demon_man said:
do you have access to another pc mate with a different operating system from yours??
Are you connecting phone via usb to the front or back of the pc?
Have a read through this thread im reading alos
http://forum.xda-developers.com/showthread.php?t=618084
Click to expand...
Click to collapse
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!

davor.klobucaric said:
ok what i did dunno, but this is whats happened
downgraded to spl 1.42 or something,
started official ruu winmo 6.5 got an error, cellphone shut down and now it wont even turn on.
Ty for all the help, realy realy realy thank you !!!!
I am off to bed, tomorow i will throw my hd2 to trash can!
Click to expand...
Click to collapse
Which stock ROM did you flash?

either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return

Demon_man said:
either you have a bad flash and its gone tits up or its bricked, either way someone will be here tomorrow when u return
Click to expand...
Click to collapse
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)

davor.klobucaric said:
STOCK ROM:
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
IT WAS WORKING BEFORE!!!
i left batery out for a couple of minutes,and now it goes to 4 colour bootscreen,
BUT! I have another problem, 1,42.0000 works, but its SPL, and if i try to go HSPL 2.08 PROGRAM CRASHES on my comp.
This is so fu**** up. I would rather send to someone who knows how to repair this. anyone interested?
Lost my will to live with this phone. i am suicidal! (joke, don't call social services)
Click to expand...
Click to collapse
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.

your phone turned off??? is your battery dead??

orangekid said:
That is the correct ROM.
you need to flash it via SD instead of RUU, that way it will put the correct SPL on your phone without you having to do anything from you computer.
edit: to clarify, flashing via RUU it cannot replace your SPL version, but if you extract that file, then move the NBH to the root of your SD card, then rename it LEOIMG.NBH, then go into bootloader, it will recognize it and ask you to flash. hit power to flash and it will restore to stock SPL, Radio, ROM, Boot Logo, etc.. you're good to go.
Click to expand...
Click to collapse
I have tryed that, thank you for your response, it went well, spl went to rom fitting, BUT,
WHITE HTC sigh on turn on, 3 RED LINES ON THE BOTTOM showing radio, and other stuff, but it constantly restarts, it wont load win 6.5. anyonne know why?

Problem with clk/magldr
was trying to flash my htc hd2 EUROP with hd2 toolkit v 4.2.0.1 i follow this steps
1-i power off my phone
2-I press in vol down button and power button in same time phone now was in 3 color mode
3- i press in task 29 on hd2 toolkit this erase my phone completely
4-then i press vol down button and power button in same time again
5- i click in clk repartition and choose 200MB
6- what happen is after all this steps my phone start with htc image blocked in white and green and i cannot boot in fast speed mode like usually.
obs, im using spl-2.0.8 HSPL by cotulla.
does anyone knows how to enter in fast speed boot mode without clk or magldr cause ive tried with these they dont work,..i just only can run wm6.5 that is .....i need help please

You are sure, you have installed a recommended radio rom?
You should use the radio rom 2.15.50.14.
Send from my Leo using Tapatalk

[Q] Flashing Problem

Hi all,
I would like to ask someone who are willing to lend me a hand.
Here comes the problem:
1. I wanna flash a NAND Android into my HD2 (not Tmous)
2. I have already flashed with HSPL2 with selection of 2.08 HSPL.
3. It went through to Windows Mobile again, nothing goes wrong untill when I am trying to flash with Magldr Bootloader with ROM Update Utility.
4. It went through again, after that the phone reboot itself and it should be displaying Magldr bootloader instead of HTC green logo stuck at the WHITE SCREEN.
5. I've tried several ways to solve it including soft-reset but still nothing happen with the same problem which is the green HTC logo stuck at the white screen.
6. Even Hard-reset with factory default reset I have tried, the process went through, but still the same problem again (YOU GUYS KNOW WHAT I MEANT).
7. So, I tried another LeoAdvanceRUU.exe which @HD2Owner had posted few months ago, the flashing process worked through but it stucked at the 0% with HTC logo at BLACK screen.
8. I kept on trying with another ROM or Radio Flashing again, again and again and it is still stucked at 0% !!! (GOSH !! I'm going to be crazy)
I really hope someone can help me out of this as I am very appreciate to those who are willing to help me. I need the phone to deal with my daily usage, please the 'PRO's out there.. ><
Thanks in advance.
P/S: The Tri-Color mode showed PB8100 - SS-BC

Did bootloader show 'SPL2.08HSPL' (or something along those lines)?

Nigeldg said:
Did bootloader show 'SPL2.08HSPL' (or something along those lines)?
Click to expand...
Click to collapse
Yes !! It does showed..coz its already HSPL-ed..but i stil duno what is happening..

you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start

I dont drink either LOL

samsamuel said:
you havent yet flashed a correct radio. Non tmous radios (..51.. radios) wont allow magldr to start
enter bootloader
flash 2.15.50 radio
magldr will now start
Click to expand...
Click to collapse
erm, I also tried to Flash the Radio ROM, but it will stucked at HTC logo with Black Screen and also 0% wont move either..

In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)

samsamuel said:
In that case double check the spl version in bootloader. Quite often people flash "2.08.0000" by mistake instead of "2.08.hspl"
(You did instal hspl before trying the radio, right? Radios news hspl too)
Click to expand...
Click to collapse
yea i did install the HSPL before flashing the radio and it is done with 2.08 HSPL
but what do u mean by Radios news HSPL?
when I am flashing the radio in the bootloader, I used the common flashing technique which is using the CustomRUU with the RUU_Signed.nbh file which contains Radio 2.14.50 and then the only the problem came out.
by means every ROM that I am trying to flash, It will still stuck at 0% Black Screen with HTC logo..

oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.

samsamuel said:
oops, radios NEED hspl , lol, darned predictive txt!
ok, so sounds more like usb timeout,
enter bootloader, connect usb, count to 5, run customruu.
If that still wont work, you can flash radios from sd, just like roms. Put teh ruu_signed.nbh onto sd card, renamed leoimg.nbh, reboot into bootloader, phone will see the .nbh and flash it.
Click to expand...
Click to collapse
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??

no, no usb needed, put the leoimg on the sd card, card into phone, power on phone holding voldown, bootloader finds the leoimg on the card and starts the flashing process.

eXcMichael said:
erm, is the flashing will do it automatically itself ?? because I am still not able to boot into whatever OS yet. And do i need to connect the USB when the leoimg.nbh flashing if its working itself ??
Click to expand...
Click to collapse
OK THAT'S WORKING @samsamuel !!!!!
THANKS ALOT !!!
I also assume the Radio was not flashed but i just cannot find a way to do the flash, and my troubleshooting was correct.
THANKS ALOT especially @samsauel and other devs' assistance. Highly Appreciate for what you guys contributed.. really THANK YOU, ITS NOW RUNNING Hyperdroid GBX ~
Thread can be closed and for further reference.

Look for HD2 nand toolkit 4.1 on XDA developers
It's a all in one utility hand HD2.
You can also try the we site addictive tips.com , they step by step tutorials.