Imate JAM says USB on lcd - JAM, MDA Compact, S100 General

Hello everyone!
I have one imate Jam that's showing USB v1.02 on lcd n it's doing nothing at all. Cant even connect it to pc or anything at all. tried to put it in boot mode but nothing happened.
Wat can be wrong? tell me procedure for fixing this!
Regards
Tom

Showing USB1.xx is the bootloader mode ! Maybe a damage switch ?
I would try to flash it .
Cotulla says : *Enter bootloader mode on device (Press POWER + CAMERA + RESET, you will see Serial/USB at top and 1.0X at bottom)
*Connect via USB to PC
*Run Update.exe
*Follow instructions in Update program.
*At the end you should see at device screen: "100% Upgrade OS Image Complete".
*After flashing press reset.
*Don't touch device, wait while "welcome screen" appear.
*Press screen, do calibration and start using device.
Good luck

Have the same problem, tried flashing but update program doesnt pick up the phone and then errors... Im using windows 7, could that be the problem?

Thanks for sharing info..
Can u tell me what rom to flash my imate jam with? I m new here don't know much about imate flashing. can u give me the link for the rom here please??
Regards,

*Connect via USB to PC
*Run Update.exe
*Follow instructions in Update program.
*At the end you should see at device screen: "100% Upgrade OS Image Complete".
*After flashing press reset.
*Don't touch device, wait while "welcome screen" appear.
*Press screen, do calibration and start using device.
Where to download rom from?? update.exe?? where to get that from?

wihandw said:
Have the same problem, tried flashing but update program doesnt pick up the phone and then errors... Im using windows 7, could that be the problem?
Click to expand...
Click to collapse
Fix it like here described, its in german but you will understand it.
The Magician must be in Bootloader mode for this procedur.
View attachment 298939
To be sure that your MAgician is o.k. flash a ROM from your Provider. Also you can get Cotullas WWE3.03 ROM from here http://cotulla.pp.ru/Magician3.html
Be sure that you have Radio 1.12 on your Magician ! ! ! !

cum instalez radio 1.12? cum imi dau seama ca este instalat. please help me

Related

How To: Revert to Windows Mobile 2003

Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Leiden said:
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Click to expand...
Click to collapse
Man! Can't thank you enough for this. I took my phone to the service centre, willing to pay for the repair, and they could not do it. Every thing works fine now. Very good manual, clear instructions and correct info!
THANKS!
Hi
I Am Trying To Follow The Procedure Mentioned. But When I Right Click On Spl I Am Not Getting 'emergency Flash' Active.
Can U Please Assist Me Regarding This
You need TyphoonNBFTools.dll installed on your phone. Try running TyphoonNBFTools and selecting Tools->Immediate Flash Tools->Test Immediate Flash. It should automatically install the required stuff for you. Check you phone when you run the program. You should get a prompt to installed a program from unknown publisher. Make sure to choose yes.
Stuck in bootloader
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
maybe u need to make a "goldcard"
my feeler (o2 xphoneII) lives again after flash with goldcard.
I can't find a way to create one for Typhoon, can you point me in the right direction?
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
er1cc said:
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
Click to expand...
Click to collapse
UR Phone is fried!
this happens to almost 1 out of 20 users.....that while downgrading/upgrading to another bootloader, ur phone becomes dead....
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
get the tricolour bootloader type in mtty info 2 the type format BINFS then upgrade using rom upgrade
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
i also got that problem but i reinstalled the patched RUU again and my phone now boot but i have not been able to go back to the 2003 as i insalled WM5 but still cant format the BINFS
If already have patcher the bootloader with the guide to upgrade to wm 6.0 can I ignore to do it again? I mean flash bootloader again ?

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

probleme flash

Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725

[SOLVED] Connection Error [262]. Stuck in bootloader (tri color) mode.

I'm new in these forums as well I'm new with flashing ROMs so obviously I messed up flash process and my device stuck in bootloader (tri-color) mode. This post I address to those unfortunate like me .
# Symptoms #
- ROM flash started and stopped at 17%. After recovery flash process stucks at 0% and pops Connection Error 262. Device is stuck in bootloader mode not possible to flash anything, hard reset does not help, flash from SD card does not help either.
# Possible cause for that #
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
2. Connection between ActiveSync and device was not established when flashing ROM file.
Before to go any further please take your time and read Polaris Wiki to get familiar with glossary and acronyms used here.
PROCEED ONLY if flashing original ROM does not help, hard reset does not help and flash from SD card does not work.
# Solution #
1. Download MTTY software.
2. Kill ActiveSync (Press Ctrl-Alt-Del and stop rapimgr.exe and wcescomm.exe processes).
3. Plug Polaris into usb port (Plug directly not through hubs).
4. Start MTTY after chose USB from PORT dropdown list (if it is not listed there then ActiveSync processes were not stopped).
5. in window type: set 16 0 (enter cmd mode)
6. after type: task 8 (this will format phone)
7. after type: task 0 (this will restart phone. Not always necessary)
8. soft reset
This procedure can damage your phone. Use it as last resort.
Official source in french here.
Now before flashing any ROMs read carefully how to flash (not install!) Hard SPL.
# P.S. about install and flash termins #
This error with flashing happened to my due misunderstanding between notions of installing something on your device and flashing. In my opinion those are completely two different things. As for first I understand of running some cab or exe directly on device. So problem comes when people sees install Hard SPL en device as they try to find some cabs or exes to install directly on device or they just copy all files to device. To make things clear Hard SPL "installation" actually is ROM flash process which must be done with maximum caution, but those who did not read Wiki won't understand it.
Cheers, whitealien
BiG THX @ Whitealien.
works to 100% on my Touch Cruise.
I flashed under Vista Ultimate...
# Solution # ... addition from me for Vista users!
....
2. Start Windows Mobile Device Center and Deaktivate USB Connection and then start Task manager end kill
Process wmdc.exe.
Rest of whitealien. and have fun!
Thank you!!!!
I had given up on this, and was sure my only option was a warranty repair :O
always welcome
Thanks, you've saved my Polaris.
Mine didn't want to react anymore to the soft reset, so I replaced your instruction 8 with:
Cmd>boot
and that did the trick.
whitealien said:
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
Cheers, whitealien
Click to expand...
Click to collapse
I had exactly the same problem, for whatever reason went back to original SPL before HARD SPL.
I solved my issue by using back the original original HTC RUU_signed.nbh and flash it using the CustomRUU.
Thereafter, repeat the entire HARD SPL and flash the home cooked ROM.
Cheers.
For unbricking your HTC Polaris, you can try also a hard-reset (if it is related to a software error):
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html
Thank you very much
you really helped
thank you again
mrfone2003 said:
Thank you very much
you really helped
thank you again
Click to expand...
Click to collapse
you are welcome.
Seems people are still falling for this error.
I'm has this error.
Solution (with SPL-2.20):
- kill ActiveSync (process, not uninstall)
- cable to USB on motherboard
- hard reset on phone
- connect to cable
- flash OFFICIAL rom
Two time I revive my Polaris.
help me please
hi.I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
thanks for the support
Thanks dudes for the great help you gave to recover my htc dual from bootloader screen. I am very happy to have my phone back. Thanks for everybody for the help they have provided generously. I appreciate alot. infact thousands times.
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
aaront1988 said:
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
Click to expand...
Click to collapse
Did you follow all steps from 1st post?
Did you kill all running ActiveSync processes?
I did indeed, i'm on vista so didnt have those particular processes going but followed the step from Aeroman and it still doesn't want to play. Any ideas?
managed to find a working XP machine and it worked a treat. Thank you so much.
thanks,this solved my pb
please help
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
wesram said:
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
Click to expand...
Click to collapse
What did you do to get there?
whitealien said:
What did you do to get there?
Click to expand...
Click to collapse
hey, im sorry for the late reply. it didnt notify me and now after posting several times asking for help in many threads by accident i bumped into this thread again to see that u answered and thank you so much.
now, what i did? this is the wierd thing, i didnt do anything, i went and back to see my phone stuck in bootload .... after this i tried almost everything i can find. from ur solution to flashing original rom to hrd spl to .........
now all gave an error except the original rom (polaris.1.28.415.2), it did went to 100% and device restarted to take me to my nightmare .... another bootloader screen am i suppose to search for polaris 1.28.0000?
i still have now the same writing shown.
please help me with this, its a nightmare .... is it totaly dead???
i managed to catch what it is saying b4 bootload screen (only when SD card is in place) it says no image file was found!!! in a very fast way and go to bootloader. in case the sd is not in place nothing happens and it goes straight to the bootloader

Htc Touch Find Aka Pola200 Stuck On Bootloader

Hi to all i have received this Htc touch find aka Pola200 that stuck on bootmode,
POLA200
Spl-1-25.0000
CPLD-2
someone can help me to restore orginal state it's a branded O2
Tanks
HI, if i´m right you got a Polaris with spl installed correctly but the OS -rom is not flashed correctly?
I copied this from the "help with flashing" thread...
How to install cooked rom.
Download the cooked rom, and unpack it to a folder.
STEP MANUALLY to bootloader. (Press and hold camera button and press reset)
You will see a tricolor screen on you PDA, and you have to see SPL-2.20.Olinex string. IF YOU NOT SEE THIS DO NOT TRY TO FLASH ROM!!!
Now connect your PDA to PC.
From the Hard-spl folder, run RomUpdateUtility.exe, or Rom.exe, (Next, Next….)
The screen will be grey, and a few minutes later the new rom will be installed.
(After rom flash Hard Reset is strongly recommended)
Click to expand...
Click to collapse
So pls CHECK if you see the Olinex string.... make a screenshot if u´re unsure...
IF THERE is any question, ask before you try to flash or s.th.
Here´s the manual for flashing Hardspl:
How to install HARD-SPL! (You MUST do it first and once!)
Download Hard-spl, and unpack it to a folder.
Connect your PDA to PC, and be sure Active Sync can connect to it.
From the Hard-spl folder, run RomUpdateUtility. (push Next, Next, and Update…)
Your will see a tricolor screen on your PDA.
It will ask you to Replug your usb Cable. DO IT!
The screen will be grey, and a few seconds later hard-spl will be installed.
If you want to check it, step manually to bootloader (Press and hold camer button and press reset), and you have to see SPL-2.20.Olinex string on the tricolor screen.
Click to expand...
Click to collapse
OK I resolve problem whit Mtty but now i want to flash whit italian Rom possible and how?
Tanks
So, i dont understood your problem at the beginning, but if its solved now ^^ fine !
So if you want an italian rom, maby take this:
http://forum.xda-developers.com/showthread.php?t=430745
Its the M-Amine 2.0 FINAL Rom... I testet it already in GER and think its one of the best here.!
The Flash-Manual is in short-form in my post above, in think in the Thread of the Rom too, and there will also be some very detailed instructions here in this forum at all.

Categories

Resources