Related
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right
Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725
After I have installed the maatiROM.V3 ROM, my phone has not been able to boot into Windows properly.
It booted into Windows the first time after I installed the ROM, however, when I tried to restore the programs and reset the device, it tries to install the ROM automatically again, however, after its all done and reset, it holds on a white screen with the HTC logo.
Can someone please give me some advice?
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Jowan073db said:
Download youre Original rom for youre device. and get the Leo in 3 colour screen then connect the usb and flash the Original rom back.. than it must work.
Click to expand...
Click to collapse
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
kayzee said:
my original version is 1.48.831.0 (71294) WWE
but I couldn't find it
I have version RUU_Leo_HKCSL_CHT_1.48.832.1_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but I dont know I need to use SSPL to install it or not....
I try to use SSPL to install it, but error [294] occur.....
WHAT CAN I DO???
thanks!!
Click to expand...
Click to collapse
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
kurniawan77 said:
Just download it from HTC support site... no need to use SSPL for this as it is the original ROM...
Click to expand...
Click to collapse
I am come from Hong Kong
Hong Kong's HTC website no download link.....
I dont know which version should I install
I got two version now
one is Official WM6.5 ROM - HTC HD2 (Leo) - English Asian Version(1.48.707.2)
the other is Leo_HKCSL_CHT_1.48.832.1-this is a chinese version which released by CSL (CSL is the provider which sell the phone to me, but my original rom is 1.48.831.0 (71294) WWE(English))
so I am very confuse now...
dont know which one is suitable....
Any idea??
thanks thanks thanks thanks so so much!!
I tried to install both official english and CSL chinese version, its show error [294].......
What should I do??????
now, the phone can get into windows(maatiROM.V3 ROM),but the phone keeping crash...and I reset it....the phone will re-install the windows(maatiROM.V3 ROM) again.... then crash again, and I reset again, and the phone re-install again.....keeping repeat crash, and I reset it, and re-install windows.......
*CRYING*
I dont know what can I do now.........
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
golumbu said:
In my opinion you can try the folowing:
- Remove sim and memory card and do a hard reset (with phone off , keep holding down the volume up and volume down keys and press power button, release all butons then press volume up again to restore manufacrurer deaults)
- Try to enter in boot mode (with phone off , keep holding the volume down and press power button) then flah again your phone
- If none of these helps and you can't find the original rom then use the GOLDCARD method. So make yourself a goldcard (serch the forum and you will find how to do that), boot your phone into flash mode with goldcard inside and you will be able to flash any original rom to your device
WBR
golumbu
Click to expand...
Click to collapse
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
kayzee said:
Thanks!!!I restored the phone to manufacurer default!Seems to be ok!!
thanks so much!!!
I
Click to expand...
Click to collapse
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
sakiin said:
It happened to me and I found out it is one of the reg tweaks in combination of a cab I installed did not work with maatiROM. The rom itself is stable and I use the Premium, which version did you use?
Click to expand...
Click to collapse
same as you!!!
I am using premium.....
Hello all,
There are many new users who want to install/upgrade to a custom rom but totally don't know from where they should start. So, they ask the same question again and again in irrelevant threads. Here is a very short guide which will help you to install/upgrade to a custom rom and will hopefully prevent newbie's from asking the same question.
@All New users: There is no problem in asking question and everybody is ready to help you but many ppl just don't go through the pages even tho the question has been answered several times in a single thread.
Things to be known:-
1. Flashing The term flashing means installing or upgrading. When we say Flashing a rom that simple means we are installing the rom. But sometimes you would have seen in forums ppl saying flash Hard spl or so. Here too flashing simply means installing.
2. Basic information On powering up your phone the basic information displayed on the screen are: ONBL version, SPL version, GSM or Radio version and OS version.
For flashing a custom rom we only need to know about SPL for now.
3. SPL Here is the description of SPL by krazy_about_technology,
SPL or Second Program Loader is a part of your phone's firmware. Its responsible for both loading of operating system and it is also used by operating system for some low level tasks. By Default, HTC and Other Manufacturers too, design it in such a way that it does not allows custom ROMs to be flashed in the phone. It does no by checking for the Digital Signature of HTC on roms. So it need to be patched in order to flash custom ROMs made by chefs in this forum.
4. H-SPL As you can see in the above description that SPL are designed in such a way that it doesn't allow you to flash custom roms. So we need a H-SPL ( Hard SPL). When we flash a HSPL it simply patches the current SPL or in other words it unlocks the device for flashing custom roms.
The flashing process
1. Flashing HSPL First flash HSPL, head over to this thread ( here ) for all the instructions and downloads of HSPL.
2. ROM Now after flashing HSPL choose a custom rom. Almost all the custom roms are compressed commonly with winrar or 7zip.
So, if you dont have winrar or 7zip to uncompress the package get any one of them. My suggestion is get 7zip from here.
After uncompressing the custom rom package there are two cases,
Case 1: There is a single *.nbh file, generally the rom file is named as RUU_signed.nbh ( but remember it may be of any other name too, just it will be of *.nbh format ). In this case you need some additional tools to flash this file into ur device.
How to flash the nbh file (this only guides you to flash nbh not unlocking ur device (hspl)
Here is a short method.
1. Download this Installation package (295 kb). here
2. Extract the above downloaded package anywhere on pc (say desktop)
3. Copy the downloaded nbh to the extracted folder. (Here the extracted folder name is Installation package)
4. Double click on ROMUpdateUtility.exe
5. Follow the onscreen instructions.
Thats it!
Case 2: After uncompressing the custom rom package you will see there are additional files with the rom file. These additional files are nothing but the tools required to flash the rom into your device. So in this case you don't need any additional files and you can directly for for flashing.
Flashing the rom:
For XP
1. Download and install Microsoft Activesync 4.5 (the latest) if you don't have it in your pc. It can be downloaded from here.
2. Connect your Device with PC via USB cable. As soon as you connect you would see a pop up window on your device. Probably there will be three options, you have to select the option which is Activesync.
Now you should see in your PC Activesync connected, if it didn't sync open Activesync go to connection setting and select the port through which your device is connected. Now re plug-in your device.
3. Run the ROMUpdateUtility.exe remember the flashing tool should be in a folder where the rom file is also present. Follow the on-screen instructions. Thats it.
For vista/windows 7
1. Download and install Microsoft Device centre from here.
2. Connect your Device with PC via USB cable. As soon as you connect you would see a pop up window on your device. Probably there will be three options, you have to select the option which is Activesync.
Now you should see in your PC Device center is connected, if it didn't sync open Device center go to connection setting and select the port through which your device is connected. Now re plug-in your device.
3. Run the ROMUpdateUtility.exe remember the flashing tool should be in a folder where the rom file is also present. Follow the on-screen instructions. Thats it.
Essential thing to be known:-
1. Bootloader mode Knowing how to enter into Bootloader mode is one of the most essential thing to be known for a opal user (windows mobile users).
How to enter?
There are two way to enter into bootloader mode.
1. If you device is on, open your device's back cover. Press the soft reset button ( red button ) using stylus. As soon as you press it, immediately press the volume down button and keep holding it until you see a tri-color screen on your device's screen.
2. If your device is off, press the power button as soon as the device vibrates immediately press volume down button and keep holding it until you see a tri-color screen on your device's screen.
Uses?
If you flashed a damaged rom, you would be no longer able to use your device. In that case enter into bootloader mode. And flash a different rom.
Thanks
Explain the excellent and easy to understand, good work Thank you
Iam glad that you liked it. I hope now ppl will refer this thread and not rom threads. Ppl can ask all the question that they ask on other threads here.
Nice Guide
You've done a great job with this guide. Thanks. I've already referenced it on another post.
i have hard spl my device...i've instales the rom from this: http://forum.xda-developers.com/showthread.php?t=680164
after that i;ve tried to unlock my phone...is from austria t-mobile...
when i've tried to use some programs to unlock the phone, the progress bar went to 7% and the a windows pups and said that there is a 260 error...
the i instaled again the 6.1 rom froms here: http://ptxserver.net/blog/?page_id=37
the i've tried again to unlock the phone but same error...
but when i started to put the first rom on mi device...opal v 6.5..i have the same problem...can someone explain how to unlock the phone and to have the first rom on my device(opal version 6.5 d25)...pls...
Ruch0 your question is not at all clear, if you want someone to help you then please make it little more clear.
Is your phone sim locked, if so then it is always said not to flash a custom rom.
According to ur question u say u have done hspl and installed a rom then trying to unlock the rom. Here by unlocking do you mean sim unlocking?
to make a better point i want to get rid off the 260 error...because i have found a lots of programs that will sim unlock the phone...
know i am trying to use this:
1. download hardspl v7 from the first post.
2. extract ruu_signed.nbh and rename it to HERMIMG.nbh
3. copy it to a microsd card, make sure the card is formatted as fat32
4. download sspl-herm from here
5. extract SSPL-HERM.exe and copy it to your phone.
6. insert sd card and run sspl-herm.exe on the phone.
7. you should see the tri-color screen and then it should change to this
8. press power button to start flashing
9. reset when you get the msg that its done.
but i cant start the sspl-herm.exe from my mobile...
LOL, that really made be to laugh. First of all are you sure that you have a HTC Touch Viva (opal) because from your description it is clear that you are using herms and having some probs. Well, my friend this section is ONLY for the device called HTC Touch Viva (opal). So asking here is a total wastage of time.
You should immediately head over to herms section and ask the ppl over there. Visit here.
do i need to install h-spl on my windows seven before flashing or not????
sanchitgrover said:
do i need to install h-spl on my windows seven before flashing or not????
Click to expand...
Click to collapse
After you have connected your device to pc and it is showing connected in Device centre (Windows 7), follow the below step
1. Flashing HSPL First flash HSPL, head over to this thread ( here ) for all the instructions and downloads of HSPL.
Click to expand...
Click to collapse
yes yes yes work fine and was very easy to do all the job 10q
Error
Hi, friends
maybe not to post it, but,
so want to flash my device, but don't, when I start de hspl flash not appear de bar, (0%), then show [202] connection error, maybe the hspl? or my device not supported? original spl 1.52.000 / F256?
thank you, if some one can help me
caioofaria said:
hey, jagan2, ok,
but, I'm working tomorrow, and the firewall, will not able to receive a remote access, but to explain, i connected my device, then I tried to run opa_hspl_v2, then it go so the bar of progresse, but in few seconds appears the error [202] connection error, I've tried in windows vista, xp, seven, all with net.framework working, maybe the my spl version? my is 1.52.0000 and ONbl 1.52.0000, gsm 1.52.0000,
I'm waiting to use your Evo 2.5A, really amazing with the features and look
Click to expand...
Click to collapse
The main thing you have to check is whether your phone is synced with ur PC via activesync/windows mobile device centre. If you are sure that it is synced then also not working then there might be some other problem.
About remote access don't worry there is a software called Team viewer it will bypass all firewalls.
Yeah, Jagan sorry, I know the team viewer, tomorrow we can use this,
thank you for ur help.
Jagan
Can u help me today?
Need Help
Hi Jagan
I have HTC Touch Viva purchased recently in India.
Software : Win Mobile 6.1 Professional Build : 19971.1.2.6
ROM Version : 1.35.720.2 WWE
Radio Version : 03.37.90
Protocol Version : 4.1.13.74
I tried to update its OS to Win Mobile 6.5 first time.
I followed your instruction in Post 1. But I am unable to do that.
First I tried HSPL 2, but it didn't work. I got 202 error.
I downloaded the ROM from the following Link.
http://forum.xda-developers.com/showthread.php?t=629257
ROM update also failed.
While updating, it showed the message like
Current ROM Version 1.35.xx...
New ROM Version : 1.27.xx...
To update the OS to 6.5, I need to do any thing else? Where I am going wrong? Plz help.
ivk: caioofaria has too similar problems that is error 202, its like in some pc its not coming and in some its coming. I will check that out again today in caioofaria's pc.
I will post result of my testing today, if anyone has a suggestion post it here.
For now iam assuming that ivk and caioofaria is not able to flash hspl because of there new default os. I will try to get a solution for this,
But if anyone has suggestion be sure to post it here.
Need Help - Update
Hi Jagan,
Little bit improvement in my problem.
The HSPL completed. Now the spl version : 1.26.0.0
Again when I try to update the ROM, getting Update Error 270.
Tried on different laptops(win 7). But getting the same problem.
Thanks.
No the spl version should be something like this 2.00 cmonex
That means you have done hspl yet. Actually i think i got the prob of the error, when you u try to do hspl and ur screen goes tri color then your pc will or i should say must install a driver it will be something like "Pocket pc syn" if its not doing then hspl will not get flashed. Just one again try to do hspl in windows 7 then when you are in tri color screen see in ur notification area below that some driver is getting installed.
hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic
basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.
Chef_Tony said:
basically, flashing a winmo phone is an easy process:
1. bootloader mode (power on with VOL- button pressed)
2. flashing
3. hard reset
however, there are a few preparations if your device was never flashed before, you need to install hspl on your phone and make sure you have the correct driver installed on your pc. the driver for the device in bootloader mode might vary from the driver used to sync the device, when switched on.
1. the driver:
if you have windows xp, connect the phone in bootloader mode and look, whether it changes from serial to usb on the bootloader screen, you should be fine by then.
on windows vista/7 you connect the device in bootloader mode, and might actually take some time for it to download another driver from windows update. if it changes from serial to usb, first try to connect using mtty, before attempting to flash, because the connection might not yet be stable and you might want to have a look at the thread (ref updating the usb drivers).
2. hspl
to quote the dummies' guide thread:
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
pretty easy, in other words, just connect the device in bootloader mode and run the package on the pc, it will unlock the spl and flash hspl.
if all went well, you are ready to flash, download any rom you like from the rom development section, and flash it using the .exe file that comes with them, might be updater.exe, blackstone RUU.exe or something else. if your rom download only consists of an .nbh file, like ruu_signed.nbh or BLACIMG.nbh, download advanced RUU and use it to flash.
alternatively, if this is to complicated for you as a beginner, you can rename the rom file to BLACIMG.nbh (if it is not already named like that) and put it in the root of the sd card, by then entering bootloader mode, it should find the rom and give you detailed instructions on how to install it.
last step, hard reset, as described in the original manual, switch on, while pressing VOL- and VOL+ and follow the instructions onscreen.
Click to expand...
Click to collapse
thnx 4 help really usefull and easy,i apperciate it
thnx again
@ blackspyker
did you successfully flash the hspl and a new rom?
(just seeing if this thread is solved or not)
Rn
just like me dear, please help us. but mine is English version
just like me dear, please help us. but mine is English version
blackspyker said:
hey guys..hope to be in a good health
this is my first theard ever here.. and honstly i found xda more useful,more likly to me rather than any websits else..so i'd like to thank guys here "u rocks guys "
now i'd like to ask about flashing anew rom for my HTC touch HD t8282
running win-mo 6.1 with arabic supported language..touch flow 3d..etc
but now i'm bored with original rom and i was looking for some roms around here and i found what i excatly wanted
but..(i'm sorry for that question :$) i dun know how to flash a new rom to my blackstone..i used search fuction and dummies guide also but..rofl i didn't get what they were takin about
so i was asking if someone could provide me with smplified way to install a new rom using HSPL
Thanks in advance and sorry for z long topic
Click to expand...
Click to collapse
download this, extract all the files, take micro SD out of device, connect device to active sync and then run HardSPLWrapper_Blackstone.exe on your pc, it will now start to flash a new SPL, when complete confirm you got it installed, go into bootloader mode (tricolour screen! {hold volume down and press the reset button under the back cover}) now verify the screen shows 1.56.OliNex, which is the new Hard-SPL version.
when complete you will be able to flash any rom to your touch hd/blackstone
note: if you do not flash a new rom you will have graphical issues with the current rom, however this gets fixed as soon as you flash a new rom
if you have any trouble, click me and go to the first post
good luck