Problem with the buttons.. - HD2 General

I had this HD2 for almost 2 months now.. and the leftmost button is now tad lower compare to the rightmost..and SOMETIMES it does not register the tactile...
I had checked some of my friends HD2 and it's getting the same problem...the leftmost is really just a tad lower..but their lowest button STILL works..is it because mime is the oldest ?
ANyone having the same observation and thus the problem..????

My on/end call button also feels very spongy (brand new handset). I will try and return it in the next couple of days...

I had three of these (sold the fourth unopened) and two of them had dodgy buttons, the other was perfect. I suspect it's mass-production that's to blame but ultimately the buttons do feel 'cheap' on the HD2 and definitely let the side down.

Been using long_press much? its sort of natural to press pretty hard, could account for it.

Related

Slight annoyance: keyboard slides too easily.

I have had my Orange SPV M3100 for a couple of weeks and I really love it. A great upgrade from the Wizard, which I only loved a little bit less.
But there is something about it that bugs me nearly every time I use it: the two halves of the device become misaligned from each other too easily.
I quite liked having the Power button on top of the Wizard, unlike the Hermes design where the button is on the side. Now, with the Hermes, I hold it in my left hand (thumb on the wheel) and press the Power with my right index finger. Theoretically I am only holding the lower half of the device to do this (the half with the keyboard) but in reality the fleshy part of my thumb pushes the upper half (the screen) to the right nine times out of ten when I press the button.
This drives me up the wall. It seems I'm constantly lining the two halves up like an untidy pack of playing cards
I'm thinking about putting a tiny bit of Blu-Tack or something in the end of the sliding channel under the screen, so that it offers a bit more resistance before the two halves separate.
Anyone else noticed this little annoyance? Or am I just being a bit picky? I didn't have this issue with the Wizard.
I too am a leftie and have the same problems. When I hold it in my right hand it isn't as bad,
Izzard-UK said:
I have had my Orange SPV M3100 for a couple of weeks and I really love it. A great upgrade from the Wizard, which I only loved a little bit less.
But there is something about it that bugs me nearly every time I use it: the two halves of the device become misaligned from each other too easily.
I quite liked having the Power button on top of the Wizard, unlike the Hermes design where the button is on the side. Now, with the Hermes, I hold it in my left hand (thumb on the wheel) and press the Power with my right index finger. Theoretically I am only holding the lower half of the device to do this (the half with the keyboard) but in reality the fleshy part of my thumb pushes the upper half (the screen) to the right nine times out of ten when I press the button.
This drives me up the wall. It seems I'm constantly lining the two halves up like an untidy pack of playing cards
I'm thinking about putting a tiny bit of Blu-Tack or something in the end of the sliding channel under the screen, so that it offers a bit more resistance before the two halves separate.
Anyone else noticed this little annoyance? Or am I just being a bit picky? I didn't have this issue with the Wizard.
Click to expand...
Click to collapse
The same here. I got my TyTn back from repair this week, also for the sliding (and other things). At first it slided with a littebit more resistance but after a day it is back to where is was: with the "easy slide...
Same thing
Had that same problem. My first TyTN died.... so let's how it goes with this new one. This is not sliding now - it so new.
I'm just a little bit afraid how this thing holds together after a year or two? Please tell how it works with you guys having few months old machine.
Has been loose from the beginning. Always slides about 5mm while turning on
with left hand.
Me too HT638F ...
But I will return it because I want an english version.

upper part is shaky when keyboard is opened. Normal?

The part where the display is becomes shaky a bit when you slide open the keyboard
Is that something that I should be concerned about or is it normal?
I think it's normal. I've examined four X1a's and they all had a small amount of play in the top part of the slider when open.
Mine has also a slight play to it (back and forth). Noticed this on the Raphael as well.
Keep in mind though, that the slider is only supported by two metal hooks situated (when keyboard out) at one end of the screen. So guess it's normal.
The play will also increase as the phone gets older (wear and tear). As long as the screen doesn't fall off I guess it's ok.
To prolong the life though, I try to be gentle when opening and support the screen when it's open (to reduce the wear and tear).
Mine's shaky when closed. Went to the service centre thrice and everytime they said it was normal.
Mine is a bit shaky as well. even when closed, but afer giving it some thought, i guess it impossible to make it totaly solid, at least with this form. i annoyes me, though. pressing the keys and you feel how it bends a little. when opened, I am afraid to press the little x or soething else on top of the screen, at least without supporting the lower side with my other hand.
Jabe said:
Mine is a bit shaky as well. even when closed, but afer giving it some thought, i guess it impossible to make it totaly solid, at least with this form. i annoyes me, though. pressing the keys and you feel how it bends a little. when opened, I am afraid to press the little x or soething else on top of the screen, at least without supporting the lower side with my other hand.
Click to expand...
Click to collapse
I support it when open, cause it's impossible to make it solid (@least not in this form factor). It's easy enough for me though.. cause the phone fits in my palm so easy (and way easier than other phones I've had - But I do miss the tilting screen from Kaiser though..then again, that needed major support when tilted)
I am new to this board, hello everybody!
I have my X1 for a week now. On mine the top part is shaky when closed, it moves ~1mm up/down opposite of the slider hinges. Anyone else?
It annoys me, but I hope it is okay and won't get worse.
Greets and have Fun with Your X1s!
i think it's normal. I noticed that as soon as I took it out of the box and was very worried. it's my first slider phone and i didn't know what was normal and what was not. reading threads like this was very reassuring for me. I just hope it won't get loose, if it stays like that, then i'm happy.
It seems really solid to me. No movement at all unless I push on it. I’m guessing it will loosen up over time.
same here, closed and opened. When I press gently in opposite corners when closed, it waggles slightly. I got annoyed/worried about this after purchasing the phone few months ago and went to the store to ask about it. I got to test three different X1s and they were all similar, so it's not a problem (or at least it's by the design
A bit annoying still though, especially when using touchscreen with your fingers. Mostly when pressing on the right side of the screen (down-right being the worst), it waggles slightly under your fingers.
Same here too. About 1mm up and down when closed, and when open, same.
And yes Jent, it does waggle a bit. Try using the phone when you're lying in bed, and hold the phone upside down... every press will move the screen about 1mm and it gets annoying very quickly.
i also have the problem with the upper corner^^

Any variability in the push of the buttons?

I probably have one from the earlier batches, and the buttons I find a bit too stiff. Would love it if they were much softer. I recently made a trip to Costco, which had a dummy phone whose buttons were much easier to press. Now, I'm wondering if later batches have softer buttons. It could be the way the dummy phone was made though...
Anyone who's ordered more than 1 phone notice any difference in the action of the buttons?
I actually exchanged my phone for a new one last week because the back button started creaking after awhile. (That was just one of several problems I had with that phone...) I think the buttons were really stiff and because of that I felt I had to press harder on the button and I think wearing down the button way too much to the point it started to creak.
The new phone I got has a much better tactile feel on the buttons now. It's a bit softer to touch and quieter.
I have my second MT4G. The first one made sometimes creaky noise on the home button but that was not the reason why I returned it. My second one doesn't have the creaky noise but the buttons are still hard to press. I come from the N1 that had soft buttons so everything with hardware buttons is a big change. I think that the buttons are more protruding on my second one; feels a bit odd but no reason to exchange this phone again.

Back Button Powers off screen?

I've been using android exclusively for the pass few days and have been really impressed with the progress that has been made on the HD2. I now find this phone to be less intolerable than when it was on wm6.5.
I have noticed i am using the hardware buttons a lot more in android. One problem i have though is that often when I use the "back" button it turns off the screen about maybe 30 percent of the time or so. I believe this because the buttons are not separate pieces but connected?
anybody else experiencing similar issues? Any fixes out there? Sorry if this has been addressed already in a different thread.
You have fat fingers
actually i have very skinny fingers. i only weigh 115 lbs. I have something else that is quite thick but if i used it on my phone i might crack the screen haha.
seriously though no one else is having this problem?
I think it's a hardware problem, maybe something (probably dirt) is stuck under your buttons?
I have similar problems with the back and middle button. It seems to be from them wearing out, which is happening a lot quicker since using android because the buttons are more necessary for operation. I've always been very gentle with my buttons, too. My phones in perfect condition except for the button issues. There's a couple threads around about the hard buttons wearing out... I don't think they were manufactured all that well personally... they don't seem all that stable. Most people don't have problems, but many have. Most newer android phones seem to use capacitive buttons. They are probably more stable that way, don't wear out easily, and have less manufacturing defects.
I've been thinking of sending mine in for warranty repair, because mine are progressively getting worse... yours might too. Or you can maybe set your volume keys as the back key. It would be great if some sort of onscreen back key could be made as that is probably my most used button.

[Q] Wobbly volume buttons on GNote3.

First off I want to start by saying that this is potentially the best piece of technology I have ever bought. I am in LOVE with the flexibility of Android (brand new iOS switch over) and the raw power and hardware of the N3.
I bought this beast a couple of days ago and I instantly noticed that the home button was a bit wiggly if I tried hard to make it wiggle. Needless to say I ran to the web and found that may others have been having the same issue but its not a deal breaker in any way. I have come to terms with it and it no longer bothers me.
What I also noticed was that the volume buttons are quite loose and shake quite a bit if I move them around with my finger. I can also hear them rattling a little bit if I shake the phone and if it vibrates there is a slight sound. Is this also standard with all N3's or are my volume rockers a one off case?
I am under a replacement warranty and getting a new piece should be no issue, but if this volume issue is a common one then I wont bother as everything else is working perfectly and I don't want to risk running into different problems with another N3.
floko127 said:
First off I want to start by saying that this is potentially the best piece of technology I have ever bought. I am in LOVE with the flexibility of Android (brand new iOS switch over) and the raw power and hardware of the N3.
I bought this beast a couple of days ago and I instantly noticed that the home button was a bit wiggly if I tried hard to make it wiggle. Needless to say I ran to the web and found that may others have been having the same issue but its not a deal breaker in any way. I have come to terms with it and it no longer bothers me.
What I also noticed was that the volume buttons are quite loose and shake quite a bit if I move them around with my finger. I can also hear them rattling a little bit if I shake the phone and if it vibrates there is a slight sound. Is this also standard with all N3's or are my volume rockers a one off case?
I am under a replacement warranty and getting a new piece should be no issue, but if this volume issue is a common one then I wont bother as everything else is working perfectly and I don't want to risk running into different problems with another N3.
Click to expand...
Click to collapse
Not seen any issues regarding Volume buttons being dodgy, only the home button. (only a small percentage tho) - Guess you just got a lemon unit, it does happen from time to time with any hardware.
I've got no problems on the home button or the volume buttons or the power button. Once you put a case on it you won't notice if it's just minor. But if it's bad, is get it changed. ..?
Sent from my SM-N9005 using Tapatalk

Categories

Resources