Related
Hi,
No doubt as many others have, I managed to drop my XDAII one too many times (they are a bit to light and smooth).
I think the speaker is no a bit duff as sometimes it stops working and I can't hear the other person. If I press on the circular bevel on the case that hides the speaker it starts to work, sometimes tapping the bevel also brings the speaker back to life.
I wanted to know, could this be a simple problem like the speaker connection coming loose or something more serious where a solder fix will have to be applied?
I think the device is still under warranty so I might be able to RMA it but I wanted to know how easy or hard is to fix this, can it be fixed by me or should I send it in to be repaired?
Cheers,
Taz
I would send it in for repair, once you break the security seal you will invalidate warranty and then you will be in trouble if another hardware failure occurs. It is probably a simple connection problem.
its just likely to be the spring connectors from the board to the speaker which is fixable (details can be found in the forums HERE).
However, the O2 XDAII has a 24 month warranty which i found out in November as i had exactly the same problem and decided to take it to my local O2 shop to have it repaired. It took them 1 week to get it back to me but they told me my unit was irreparable and gave me a reconditioned unit as a replacement. I was not very happy as the case was scratched all over etc and my unit was as new. I complained and asked them to give me a new unit. After a further 2 weeks and 2 more instances of sending it back to the repair centre i eventually got a brand new fully boxed XDAII (second battery, second case, second cradle etc etc) from the O2 shop but not until i kicked off with the manager stating how unprofessional O2 was in repairing/replacing a unit that was under warranty.
NB. New XDAII screens are no where near as good as the original screens when looking at it from an angle. They look fine straight on but colours fade/change when viewed from below or from the left.
Hope some of that helps.
Cheers mate,
I think I still have about a year on the warranty but I heard that the XDAII are no longer in production so I am a bit worried that I may not be able to get it repaired however a pal reckons they should upgrade me to the XDAIIs (I had one, didn't like it).
I will visit my local O2 shop in a few days and kick it off with the manager as well... to get some results of course
Cheers,
Godz
I got a serious problem with my mda vario here.
sometimes, 7 out of 10 times, when i get a call the screen gets totally corrupted and jumbled like on the picture in the attachment. i can only see black vertical lines on a white screen. in order to make the screen work properly i have to turn the phone off/on (stand-by mode) then.
does anybody know where the problem is?
i have to confess, that the phone slipped out of my hands and fell on the ground 3 times so far.
thanks
well, you say youve dropped it 3 times already? is it possible that something may be loose inside? is there cosmetic damages from dropping?
yes, there are some scratches on it. i don't really think that something is loose or broken, because the screen gets only on icoming calls corrupted.
so i don't think that it is due to a loose contact or something like that...
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
roads said:
I have exactly the same problem. I personally think it is unlikely that dropping the phone has caused it as it corrects when you cycle the power button. Any help on this from other forum member would be much appreciated.
Click to expand...
Click to collapse
Any resoluation this? I have the exact same problem!!
Oh dear ... somethings in the air...
mine's got it also. first time i saw it was a couple of days ago. only happens with the alarm clock in the morning :?
My phone is crap like hell... gotta hard reset and reconfig the damn thing. acting up lately...
(ps... AFAIK i barely dropped the phone... maybe 1 or 2 times. nothing more)
I have the same problem
I have read the service manual of wizard and said:
Unusual Vertical / Horizontal lines or partial display
(1) Check the connection of LCM FPC whether is properly connected. (Is a conector between motherboard and LCD)
(2) Try with another LCM. (LCM=LCD Screen)
(3) Try with another Main Board.
(4) Replace LCM if necessary
(5) Replace Main Board if necessary.
(6) Once the defective part has been identified, verify it again with the defective part whether the
symptom could be duplicated
Any sugestion?
Okay..
so far, i have installed Molski 2.26 rom (30meg free version) and upgrade the radio rom form 2.25 to 2.47.
I have not had another occurance of this so far.
Maybe a fluke.
Screen fixes when pressure applied to bottom of the screen
Guys,
I now have to keep my finger pressed hard against the bottom of the lcd unit to get the screen to display to work properly. it is under warranty with Imate but they want me to send it to Abu Dhabi for repair. I'm in Canada and concerned that I may not get it back.
So has anybody else identified this as being a loose connection rather that a real hard fault. Also has anybody fixed their unit by dismantling and reseating the connections.
Finally has anybody used the Imate repair service and was it timely & reliable?
Any advice would be appreciated.
Mick
This is a real hard fault.. had it with my mini s, took it into the shop, it was away 2 weeks... and in the end they gave me a replacement!!
I agree - took it completely apart and cleaned everything ....
And still have the issue.
Serves me right for buying something in Middlesbrough I suppose
It must be a hard fault with the LCD assembly. Will have to see how Dixons handles an overseas repair.
Take care & thx,
Mick
I had the same problem, in the end i took it into my local t-mob shop to have it repaired, they ended up sending me a new one.
Well, I've exactly the same problem since the past two-three weeks, it also occurs only in the morning. I'm living in the Netherlands and this is happening since it's rather cold over here, especially in the morning (3-4 degree Celcius). Since my bedroom window is open during the night, it gets rather cold in my room.
During the rest of the day it is +8 degree Celcius, and the phone works flawless. Maybe this problem has something to do with the Temperature?
Temperature
Bebob - don't thin so as I have had this problem for a number of months and the temp here in the summer is high (30+ degrees C)
It looks to be a bad connection type issue and may be a bad screen cable. It makes sense though that the issue is at the bottom of the screen cos this is where we press the select buttons all of the time.
Pls keep me posted on how you do. mine is going to a local repair shop (on my dime) tomorrow to see if they can fix it.
If not can any of you guys recomend a new unit that could be considered an upgrade to the KJAM ?
Many thanks
Mick
suggestions needed
friends, i have o2 mini s and got the same problem with screen for the last 3 weeks....
can anyone tell me that will the problem aggravate or else will i be able to use my cell properly for few months...
and also what will be the approx cost of repair..
all suggestions will be warmly appreciated...
It's happened to me as well. I have lived with that for one month now. It is happening, when I touch the cursor keys or when touch the lower part of the display. I tried "shaking/hitting" the xda and it looks better, so I assume it is a faulty connection cable.
I have active Cleartype and no more vertical lines for the past 2 days.
I seems to be a problem when background is white and leters are black.
Regards
similar problem
i dropped the phone (T-Mobile MDA Vario) and now when i turn it on the screen is fine for 5-30 seconds but then it scrambles, but works again if i smack the bottom of the phone on my hand!
t-mobile staff told me there are sensors to identify if it has been dropped. I'm suspicious that it could even be programmed to go "faulty" once it is dropped as the screen is fine for a limited time so it obviously works somewhat. do you know if this is the case? or what's happened? also is it a simple thing i could do myself? i didn't take out insurance so that's why i haven't just claimed off that as i'm really broke
Any help is appreciated
Regards,
Steve
whiteish screen / over temperature
hi,
I have a problem smilar at qtek 9100. I had upgade to my ppc wm5 to wm6 around 3 week ago and overclocked to 221 mhz with batery status today plug-in . 2 days ago Screen became whiteish (almost no contrast or over gamma) and working temperature is around 30c. I tried to re-flash with many kind roms but noting chaged.
Is there anybody has these kind of experice. If I can not solve. I am planing to buy new LCD ( I am not sure new LCD will solve the problem)
Thanks
Same problem here. Dropped it ONE time and the screen went crazy. Sent it to my t-mob shop and they got it repaired. They said in the report that they changed the "flex". Dunno if this helps.
So I got my TyTN via import back in August and I am experiencing several problems a few months later: the keys on the front intermittently cease working, the handset speaker makes small buzzing sounds when connected to a GSM network, and sometimes the screen washes out white.
1) I'd like to contact HTC USA for support options, does anybody have the number?
2) Also, does anybody know if they have an advanced exchnage option where they send you a refurb (after you give them a credit card number) and don't charge the card as long as they receive the defective unit back in two weeks or so?
The US HTC can not help you, I've already contacted them. You have to send the device to Europe HTC and have the repair done there. They have 2 HTC offices here in Houston TX one is a repair shop and they said they do not have the knowledge or parts to repair the TyTN that I would have to send it to the country from which the phone was purchased. I think this is complete bull. They could get the parts easly and repair or replace my phone, they are just making it harder to get the TyTN fixed hoping you won't bother them. I am having the screen alignment issue and my phone locking ALL THE TIME!!!! but I have not sent it in becuase I can't handle not having my phone for 2 weeks. I sent an email to HTC Europe asking how long and if I could get a replacement since I have been having so many problems and they never responded.
As far as I know they have no lowner or replacemnet program. I suggest you buy a cheap GSM phone and keep it as your back up.
any luck getting your repairs? I am having soe problems and my imei is definitely from UK.
I bought mine from MadMonkeyBoys gadgets and he has been very responsive in providing support. Although I had to wait until I had a new unit to sustain me during tyTN's repair (now I have a Cheetah), David from MMB quickly got me a repair order and I shall send the unit out tomorrow
Hi guys,
I could not find any other "help" section, so I decided to write my problem here. My Diamond 2 has some sort of display problem, device works, same with touchscreen. I can blindly control the phone, but I can't see anything because LCD does not work. I attached a photo of how LCD looks like when it is not in standby (light on). LCD looks fine with light off (in standby/turned off).
Anyone knows what this might be? I don't know how it happened, but not by my direct action. I checked a clock many times that day, and later when I checked the phone I just could not get LCD to work anymore. Just this.
I already e-mailed HTC service for support. I bought the phone from Amazon UK like 3 months ago, so I think warranty is still valid. I just hope they will not cause any problems and repair the phone without any fees. I am just checking here for your expertise on the matter. Maybe there is someone else here with same problem.
Thanks!
* I tried hard reset button
Hi
By pressing the button at the top (to check the clock) so many times the button may have got loose or the the wires connecting the LCD to the motherboard may be loose, I had this problem with my Nokia N85.
Best thing to do is get it repaired under warranty. First, ring or email Amazon and see what they can do. If your unwilling to send it off Carphone Warehouse will do the repair it for you but you have to find the repair centres. They have quite a few so it should be too hard to find.
Also Carphone Warehouse will not charge you as long as you have proof of purchase.
Man.
Is sending the phone to the Carphone Warehouse a good idea? I was just browsing the net and found many complaints about their repair services.
I sent my Nokia N85 for repair and it was ok. But I can see why your asking because I read the same reviews.
You should definiately try Amazon first.
Man.
Hi,
anyone had such problem? Service visit required? It's unlikely I've pressed it too hard also never got wet.
Thanks for any advise.
Bartuzi
bartuzi said:
Hi,
anyone had such problem? Service visit required? It's unlikely I've pressed it too hard also never got wet.
Thanks for any advise.
Bartuzi
Click to expand...
Click to collapse
Someone has had this in the past, its a "send it back for repair" situation I think.
you can try using those sucker to suck the part out.... also try to pess the corners of the screen and this should be able to solve the problem.. the problem is the glass of the screen sticking onto the capacitator that detects our finger touch
detion
pressing helps but only for a sec, after letting go it comes bach, what about sucking out, any details how to do it?
You can try putting it in an airing cupboard for a few days, see if that'll dry it out, probrably better to go for the return option, least you know it'll get fixed properly.
thanks Guys, I'll try drying, if not service visit...
A friend of mine has the same problem, as some other guys too. There is also a thread - in German language - at 'PocketPC.ch' about this problem.
The dot sometimes even disappears! A few hours later it is back, really strange. He already send it to repair but it came back unrepaired. Maybe at that point of time it was not visible. After contacting the service once again asking if this could be a general hardware problem he was told "Yes it could be a general hardware problem of the HD2." And what is more HTC has some problems to get enough spare parts (display ?) for repair. Some users at 'PocketPC.ch' reported that their device has been for weeks (5 or 6 weeks) at the repair center because HTC could not deliver the spare parts.
Let's see how it goes on.
Best regards
These are very helping information, I'll try drying option than rather going to service which 20 km away via terrible jams
HTC HD2 screen problem
Hi,
I have had the same problem. Did you solved your problem, or have you learned anything about it?
Cheers,
Mehmet
bartuzi said:
Hi,
anyone had such problem? Service visit required? It's unlikely I've pressed it too hard also never got wet.
Thanks for any advise.
Bartuzi
Click to expand...
Click to collapse
Have a look at this thread....
http://forum.xda-developers.com/showthread.php?t=613631&highlight=screen+spot
It's been a problem for some people before and been fixed without sending their phone away. I think you need good suction
to johncmolyneux
suction you say I'd appriciate any details on that...
I've read the thread, coclusion is simple if it doesn't dissapear after max few days BY ITSELF, repair it! there are few lucky people who got it dissapear after suction, heating and so on... mine stays on the screen for few months now. Indeed after leaving it on a sunny day, the dot got signifficantly smaller.
hair dryer
hair dryer helps onlu for 30 minutes, maybe it should run for 12 or 24 hours?