My XV6800 fell in water on Christmas - Mogul, XV6800 General

Getting out of an SUV (my XV6800 was in my pocket) it somehow popped out and feel in water (huge stream in street it was raining and snow was melting). I immediately dried it off. Pulled out the battery and put it in rice. Today I get all these weird leds. It seems like the screen is broken since I heard stuff going on. I tried to do a hard reset with two software keys and the soft reset.
To my surprise I got the screen back on. But now I am in a Restore waiting for complete screen. When its does I hit space to boot. But it just goes through the restore completed screen.
Is there anything else I can do? Thanks in advance.

I had the same thing happen. Baby dropped mine in the toilet. Be sure to check the screws on back. For some reason that loosened mine up and my touchscreen wouldnt work....good luck

Thanks.
Is there someway I can flash it to MR1 via an SD card? Someway I can avoic this restore screen?
edit: Ok I fixed it. At least I can use it again but most all physical keys are dead. Great...

I have an XV6800 that you may want...
I have an XV6800 that has a bad ESN. It reads zereos for the esn. I could sell it to you and then you could either use it for parts, or reprogram your ESN to this device. I know it is possible to do ( I have messed around with it some on this device just to see if it works). PM me if you are interested.

Related

VZW warranty replacement

Last night, one of the springs broke on the slide out keyboard of my XV6800. The sliding is loose and sometimes gets hung up on the broken pieces. A visit to my local VZW store today revealed that the phone wil not be fixed, but will be replaced under warranty. Now I have to start all over after all the customizations and installed programs... What happened to the days when a simple phone problem was fixed on site? This spring can't be a big job to fix...
In all my reading, I don't remember anyone mentioning broken springs on this phone. Anyone heard of this happening?
maddog241 said:
Last night, one of the springs broke on the slide out keyboard of my XV6800. The sliding is loose and sometimes gets hung up on the broken pieces. A visit to my local VZW store today revealed that the phone wil not be fixed, but will be replaced under warranty. Now I have to start all over after all the customizations and installed programs... What happened to the days when a simple phone problem was fixed on site? This spring can't be a big job to fix...
In all my reading, I don't remember anyone mentioning broken springs on this phone. Anyone heard of this happening?
Click to expand...
Click to collapse
if you do a complete backup of your phone then when you get the new phone put the rom that the backup file uses on it then restore your backup, voila all your work isnt lost.
I actually had all 4 screws loosen on my most recent. Therefore, the face came completely off and the ribbon cable broke leaving my phone bricked for a couple days. Things happen.....

Water Damaged G1?

I spilled water on my phone they other night in my sleep. When I awoke the phone was still on but had frozen up. Upon a reboot it locked up on the splash screen and with a couple more tries it locked up on a black screen. Eventually I got it to boot to home but the touch screen isn't working and I'm getting force closes when I try to open any apps. I tried leaving it in uncooked rice to absorb the moisture overnight but I'm still getting the same problems. Anything I can do?
There are two very important rules when electrical equipment is soaked.
1: take the battery out as quickly as possible so it shuts down and doesn't short.
2: LEAVE IT OFF UNTIL COMPLETELY DRY! This can not be stressed enough. Having it turned on with water inside is like trying to kill yout phone intentionally.
I find the best way to dry it is to take of any covers, batteries, sd-cards, sim cards ad anything else you can easily dissasemble, and then leaving it in an oven on 40-50 degrees overnight. Electrical stove is kind of neccessary for this though, unless you have a gas stove with good temp adjustment.
If I bought a cracked LCD G1 and replaced the digitizer with the one on my broken phone (touch screen isn't working) it should be fine right? There are no actual electronics to the digitizer screen, right?
Snakebear said:
If I bought a cracked LCD G1 and replaced the digitizer with the one on my broken phone (touch screen isn't working) it should be fine right? There are no actual electronics to the digitizer screen, right?
Click to expand...
Click to collapse
Theoretically, that should work. Haven't done it so I cant account for it.
However, how will that stop the FC's?
No, you misunderstood. I plan to buy a functional G1 with a cracked digitizer and use my old digitizer from the water damaged phone to fix it.
Nevermind, just found out the glass has some electrical parts to it and that's probably what I shorted out. Guess that's out.
I had my phone in my pocket when i went on a drunken creek walk. Long story short I pulled my battery had the same problems as you. So for my fix I wiped flashed a new rom then wipe again for good measure. Stopped force closes and works like a charm now.
read my post here for water damage if it happens again....
http://forum.xda-developers.com/showthread.php?t=616213
Well I did a Nand backup to no avail but I havn't tried a full wipe/format. Maybe I will give that a go and see if it helps. Did your touch screen also fail?
I'm currently using the G1 my brother dropped in a toilet. It accidentally turned on when he was removing the battery. It's really odd that the phone is working 100% at the moment.
Give it a few days before you rule it dead.
My sister dropped a RAZR in the toilet one day (Stoopit!) so my dad took it out (no pee in derp), hair dryer, rice, window, BAM!
Snakebear said:
Well I did a Nand backup to no avail but I havn't tried a full wipe/format. Maybe I will give that a go and see if it helps. Did your touch screen also fail?
Click to expand...
Click to collapse
The left side of my screen did not work for about 5 hours after I placed it in rice. Some say you need to keep it in rice for a full day or so. Basically take out the SD card, sim card, and battery and place the rest of the phone submerged in rice for at least 8 hours or so. Then try the phone.
BTW, my phone was acting sluggish ever since then so this morning, I did a factory wipe of the phone and things seem to be working normally. I also copied the SD contents and formated the card.

Dropped phone in water

So i dropped the phone in water. Took it out and dried it and after couple of mins i turned it back on. Goes after the S animation and black screen. Turn off and turn on again, now it wont go after main screen. After i used hair dryer for few minutes.
It was only in water for <2 seconds.
It constantly is restarting the phone and won't go past the i9000 screen. Am i screwed? Anything i can do to get warranty or no?
Ny friend put his phone in uncoocked rice for a while and that helped his phone, otherwise when did you get the phone? What carrier?
sent from my rooted captivate
I won it off a contest bell had. Have all papers. Got it in september and got warranty left. Never modded, except unlocked but i believe i can put lock back on
also as soon as i put battery, it turns on. in the event of repair, what do i say to samsung?
1. You shouldn't have turned on the device until you're sure that it's dry internally
2. Moisture indicators are likely to indicate that your device has been in contact with water. Samsung may deny the warranty or give some courtesy by closing an eye. Depends on your luck.
3. You may attempt to continue drying it and prays that it functions again
4. Perhaps try entering bootloader/download mode and reflash?
I dissemble it completely. Now one thing i need to fix is the side grill (silver strip) can't seem to put it back on..
ok sweet, it was able to boot further. I will be putting it back inside rice but any help with the side strip?
Also that big black thing is kind of lose (top right). Supposed to be like that?
ok, really weird issue
At first it worked fine, after i managed to put the strip on, i turn on and see blueish screen and everything is fine except graphics looks like 98 with blueish screen on top!
There are plenty of advises on the web if you Google for your subject. The most interesting ones are to place the phone without battery into rice for a week ot so, the other one is to place the phone without battery in refrigerator, well, all of them say to NOT TURN ON YOUR PHONE at least for 4 - 5 days if not more. However, I had this problem with my previous device and now it is working like a gameboy with no radio. My home insurance payed me for this, so if you have home insurance, be prepared to claim.
EDIT : the moment problem has happened you must pull battery out and place it as far as possible from your phone for a few days.
Sent from my GT-I9000
so what do i do now???
Any way i can claim warranty - as in do something to the cell etc?
The blueish screen = nothing on internet can be found
Also its impossible for me to lock back the phone
Turn your phone off, remove battery throw it into a dehumidifier for a day. Don't touch it. The more you turn it on the more likely something will short circuit and permanently damage your phone.
Most warranties do not cover water damage and there is nothing you can do about that.
If you have insurence my advise report it lost and claim replacement i insured my sgs against everything i already replaced it once from killing it flashing it but i am covered for water and accidental
Sent from my GT-I9000 using XDA App
Most devices have a moisture detector for if you ever drop it into water, voiding your warranty.
bad move turning it on worst thing anyone can do.
If your in blackpool, uk i can look at it for you.
best thing to do if this happens to anyone is.
take battery out.
put phone in a sealed pub of rice.
leave for 2 weeks and pray.
never ever turn it on after liquid thats when the damage happens
Grim, just grim!
oh boy :-(
thanks for the tip with the rice, good to know just in case..
Sorry for reviving this thread.
I too got the phone wet. I put it through a blower dryer and in a bag of rice.
the screen is fine no discolorations and it booted right up,but crashes on the desktop. i restart it and it stays at the galaxy s2 screen. i can enter recovery and so on, but i don't want to restore if i have too.
What should I do?
velvetmxo said:
Sorry for reviving this thread.
I too got the phone wet. I put it through a blower dryer and in a bag of rice.
the screen is fine no discolorations and it booted right up,but crashes on the desktop. i restart it and it stays at the galaxy s2 screen. i can enter recovery and so on, but i don't want to restore if i have too.
What should I do?
Click to expand...
Click to collapse
A crash at the desktop would normally indicate a software problem, but it is highly unlikely that the water had caused damages to the software. Rather, the water probably damaged the processors necessary to run the software. You can enter recovery mode probably because recovery mode does not require the full power of the processors.
So I think if there is any hope of saving your phone at all, you should reflash the firmware from recovery mode.
Do a nandroid backup, reflash and see if it was problem with ROM.
Sent from far, far away GalaxyS
lukaszD. said:
Do a nandroid backup, reflash and see if it was problem with ROM.
Sent from far, far away GalaxyS
Click to expand...
Click to collapse
i attempted a nandroid (I already have a saved nandroid) but wanted to backup this one since i'm not sure it sync some of the contacts.
when attempting the nandroid i got an error during thee backp portion of the data.
does that mean i should just recover from my original backup?

[Q] Help - I Drenched My A500...

Need some help here. I "managed" to drench my tab. Yeah, I know - stoopid me. So what's done is done. Currently the tab's display in not working. I think I was able to power it up - white light on the power button but this stays on forever.
I'm going to return the tab. So here's the question - how would I go about doing a factory reset without actually logging in to the tab?
Thanks in advance.
Bang...
Yeah I really did a banged up job on the tab. LOL!!
Could try to salvage it first and restore and then return it. Odds are if you turned the power on after drenching it you messed it up badly so youre data is gone anyways.
First of all, you should not have tried to turn it on until it was dry. That can cause shorting.
Any time an electronic device gets wet, pull the battery as soon as possible.
Stick it in a bag of dry rice for a week or two (pulls the moisture out) before trying to power it on.
I have a friend who's phone went to the bottom of a lake 3 times. Came back from it all three.
entropyiv said:
First of all, you should not have tried to turn it on until it was dry. That can cause shorting.
Click to expand...
Click to collapse
Indeed. NEVER turn on a wet electronic device. Especially in case where it's got as heavy-duty battery as a tablet or laptop has.
+1 For the rice trick. Silica works as well (the stuff that comes with a new pair of shoes).
+1,000,000 for never ever turning on a moist device! Water conducts electricity, so as entropyiv said, you probably shorted it out.
I'm also thinking that returning the tablet isn't going to work. They'll know immediately that it got wet, and that's a pretty straight forward warranty killer!
Good luck, and let us know the outcome!
most stores dont check for water damage. If you biught it at target youre in luck. When i worked there we were liniant if you had a reciept.
This is why I bought the accidental warranty...
I ride a motorcycle and have gotten radios and such wet in the past. I make sure and turn them off immediately, remove power and then once I'm home I leave them in the hot garage for a few days and I've never had a one that didn't come back to life.
Thanks...
for your responses. I'll try going the usb route to get rid of all my personal data off the tab. Once again, thank you!
The best advice I could give you as a former Compaq Computers Engineer is to take the back cover off, disconnect the battery if you can and unplug anything back there that you can. Leave the tablet in a relatively warm room for 24 hrs, reconnect everything and 9 times out of 10 it will work again. I'm not sure if you permanently ruined it trying to immediately trying to turn it on, but try this advise and see if it will work for you.
Good luck!
Ted
Wish I had the accidental on mine, i'm in the same boat. Only I cant do much with it.
BTW, anyone want a perfectly good iconia battery?
Markon101 said:
Wish I had the accidental on mine, i'm in the same boat. Only I cant do much with it.
BTW, anyone want a perfectly good iconia battery?
Click to expand...
Click to collapse
There was a guy with a busted screen.another withbdamaged case.part it out and you can get most of your money back.
Look for other damaged and droped unit threads
Good luck to you both
If it's warrantied, I would put the charger in it and toss it back in water to make sure it's fried good. Anything so it doesn't appear to power-up.
Or... if it had Recovery loaded, try to work through the menus for wiping before adding a mod. Touch screen isn't used.
What happened ? I only ask because the case seems like it would hold water back for at least a couple seconds, enough to get it out without the components getting wet.
Hello and thanks once again to everyone who'd responded.
I left the tab with some silicon gelica thing in a bag in a hot room for two days. Powered up the tab, looked like it was going to work - e.g. acer logo came up, as well as the android logo. I was feeling optimistic that the tab may just be fine. But alas, the LCD just won't work. I got a screen that's constantly flickering, snow, etc. It sure looked like the TV from the movie Poltergeist. lol!!
At least I can boot this sucker up. Now to see if the HDMI port is working or not. If it does, then I can hook it up to my TV, plug in a USB hub for a mouse and keyboard...then I should be able to do a factory reset to clear my personal data. Keeping my fingers crossed that this will work. Worse case, my Win 7 PC should see the tab and maybe I can "format" that thing from there.
Don't worry, I am NOT returning this to any retailer...this unit was not "store bought"...it's an engineering sample that was on loan to me... ;-)

DVP sudden weird behaviour

Hi,
I have a DVP 16 GB. It's been 1 year. A few days back it got wet in the rain. When I took it out of my leather case, the back button and search button lights were on and the camera was continuously blinking. I took apart everything and dried it in a bowl of uncooked rice. After that, it was working fine. No problems. Then suddenly from yesterday, it has started to act very weirdly. Whenever I switch it on, it works for a few seconds and then freezes. If I lock it, it freezes. But it remains switched on. The touch just doesn't seem to work. I have even hard reset it but to no avail.
At times, it works, i.e., after a few shut downs and reboots, but very slowly. The touch takes ages to respond. Please help.
cheerfulari said:
Hi,
I have a DVP 16 GB. It's been 1 year. A few days back it got wet in the rain. When I took it out of my leather case, the back button and search button lights were on and the camera was continuously blinking. I took apart everything and dried it in a bowl of uncooked rice. After that, it was working fine. No problems. Then suddenly from yesterday, it has started to act very weirdly. Whenever I switch it on, it works for a few seconds and then freezes. If I lock it, it freezes. But it remains switched on. The touch just doesn't seem to work. I have even hard reset it but to no avail.
At times, it works, i.e., after a few shut downs and reboots, but very slowly. The touch takes ages to respond. Please help.
Click to expand...
Click to collapse
Sorry can't really help man. But what it's worth, I haven't read anything like that appearing on the DVP, so it might not be a usual failure on this phone and rather related to the swim it took? If you grab a parts DVP off ebay, maybe you can swap parts until you isolate the prob... at least you might be able to find a cracked screen phone and place your screen on that puppy? Good luck. Phone probs suck :crying:
aleunge said:
Sorry can't really help man. But what it's worth, I haven't read anything like that appearing on the DVP, so it might not be a usual failure on this phone and rather related to the swim it took? If you grab a parts DVP off ebay, maybe you can swap parts until you isolate the prob... at least you might be able to find a cracked screen phone and place your screen on that puppy? Good luck. Phone probs suck :crying:
Click to expand...
Click to collapse
I got a touch screen, took it to a shop, got it replaced and it still is dead.The shop person told that the touchscreen strip is faulty. That needs to be replaced. Any idea on where I might get it?
cheerfulari said:
I got a touch screen, took it to a shop, got it replaced and it still is dead.The shop person told that the touchscreen strip is faulty. That needs to be replaced. Any idea on where I might get it?
Click to expand...
Click to collapse
Can anyone tell if it is the problem with the whole strip or just the ic?:fingers-crossed:

Categories

Resources