Hi Folks!
One week ago my little Prophet worked just fine. everything was going as it should.
But 3 days ago, i discouvered, that I couldn't establish a usb-connection anymore.
Windows doesn't recognize the device as a new usb-device when I plug it in.
The Prophet can only be charged via usb-cable.
I tried it on different PCs with several usb-cables. I tried hard-reset. None of it worked.
I would like to reflash my Prophet Shadow 2.0 ROM via ActiveSync, but I can't - is there a possibility to flash via SD-Card?
can you charge it?
My prophet's USB connector is broken, it's loose from mainbord.
Got a Diamond now, but thing I try to solder that connector. Check if your connactor has a faulty connection to mainbord maybe? If it happens to mine, maybe yours can be a bit loose too.
I just bought used Hima through, because I broke LCD screen on mine. And I got it with some old German ROM on it, it's working fine, but I would like something newer and in English. The thing is, that when I put phone in USB craddle, it only charges the device and says that USB Device Not Recognized. I cannot upgrade ROM nor anything else, just charge it. On my previous broken Hima, I had no such problem... Does anyone has clue what is wrong and what is the solution?
Thank you in advance...
I just found out that when I want to sync, I can do it, but have to pull cell phone toward me while it's in craddle. But doesn't work when I want to flash ROM. So I guess it's pins problem. I looked them and don't see anything bad, anyone has clue what to do?
OK, I finally managed to install ROM, I had to stick something to push forward my Hima in cradle. Does anyone know what can I do to fix that problem? It's the pins connection problem...
first of all..i don't understand why you started a new topic on this problem because THERE IS ANOTHER TOPIC WITH THIS PROBLEM JUST 3 LINES DOWN AFTER YOUR TOPIC...if you had read but didn't......about the conectivity problem with the pins cradle usb cable and advanced functionality of the usb-pc function..and thath it works just for the charge and for standard conectivity is says device mailfunction...
Because I had german windows 2003 that had no advanced functionality of the usb-pc connection! And also I didn't see too many similarities with those posts which aren't three lines down after my topic.
I changed 2 craddles and also had same problems. But I managed to access PPC when I gave some pressure on cell phone while in cradle...
I have another broken Hima (LCD screen broken), and wondered if I could take his connector?!
Hi all,
I had my set flashed to wm6.5 by Keyzx and it is wonderful.
Lately when I tried sync it with my computer and laptop, winxp detected it as unknown device and activesync shows that it is not connected at all with no partnership with the ipaq.
I was wondering if the USB port which is faulty but I can still see the ipaq is charging when it is plugged into the usb port. I had tried downgrade the WM to 6.1 but still no vail. I did changed several usb cables but still nothing. Anyone facing the same problem? Can anyone give any valuable pointers on this issue?
I had tried hard reset, soft reset and many more but it seems like not working.
sometime it happen but usually can be fixed by soft-reset or reboot of your own comp
Hi Keyx,
I am a big fan of your ROM and thanks for the advice.
This is not the first day that this happen but it had been like this almost 2 to 3 weeks now. I had tried soft reset, hard reset and restart of pc but it wouldnt detect the 612c. I was wondering if there is anyway for me to restore the rom back to the original and reflash it back to your cooked rom... as I do love the cool interface.
Sorry to bother you but I do hope you can guide me on this.
Regards,
Lee
ya i think there is stock hp rom somewhere in the forum which you can flash through sd or dnw, one can be found here
The same thing happened to me. I tried different computers, USB cables, uninstall/reinstall activesync, changing ROMs and nothing worked. The problem is the mini USB connector is very fragile. Your connector is most likely broken. I hope you have a warranty. I'm on my third unit due to the connector. The first one quit charging all together and the second one did the same as yours - charge only no sync.
in the very worst case you could live with bluetooth activesync if the connecter is really broken
keyx said:
in the very worst case you could live with bluetooth
activesync if the connecter is really broken
Click to expand...
Click to collapse
Excellent way to troubleshoot keyx. That is so obvious it never occurred to me... I wish I would have done that before I returned the phone.
Yes, I guess that is the only way to activesync right now... using the bluetooth. I believe my usb connector is not functioning anymore as I had the original rom flashed on my phone and I still cant detect it on my laptop and desktop.
Thanks all for the information and its very helpful.
i have tried to update to this radio twice now. both times after updating my computer will not recognize the phone after updating to the newest radio... any help would be appreciated
i dont think that has anything to do with the radio so try this....
1.take off any programs for your phone (exda-net, easytether)
2.reinstall htc sync(most current)
3. turn usb debugging on on your phone
that worked for me so maybe it will work for you
edit: i used the search function and came up with this!!http://forum.xda-developers.com/showthread.php?t=654940
Bad--Dog said:
i have tried to update to this radio twice now. both times after updating my computer will not recognize the phone after updating to the newest radio... any help would be appreciated
Click to expand...
Click to collapse
and welcome to the forums bro!
lv2bll said:
and welcome to the forums bro!
Click to expand...
Click to collapse
thank u very much
After updated to this radio, I've experience buggy USB connectivity (where if I start to charge it, the device will [sometimes] think it's connected to a usb device, after unplugging it will not detect it's removal).
I've also had the touch screen flip out, where it will not detect my actions at all. The way I fixed this was to connect to a machine where it then started to respond again...
Anybody else experience this weirdness???
AboveUnrefined said:
After updated to this radio, I've experience buggy USB connectivity (where if I start to charge it, the device will [sometimes] think it's connected to a usb device, after unplugging it will not detect it's removal).
I've also had the touch screen flip out, where it will not detect my actions at all. The way I fixed this was to connect to a machine where it then started to respond again...
Anybody else experience this weirdness???
Click to expand...
Click to collapse
Haven't head that one before. Have you tried another cable? That sounds suspiciously like a cable or USB port problem to me. The radio shouldn't have any effect on your USB connectivity.
sorry for the delayed response -
I used various usb cables and experienced this. The way i worked around this was to use ferrite insulated usb cables only and cut the green and white cables on both ends for the cable in my car. It seemed like the phone didn't like to detect and undetect devices often - all is well again.
Sent from my MatrixROM using the XDA mobile application powered by Tapatalk
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
...
6.5
Babbelut ROM WM6.5-28005 v0.3 NLD/WWE
*spb mobile shell is great, he is currently developing beta rom
http://www.sendspace.com/file/97d3p7 (download link for v.3)
http://www.megaupload.com/?d=ZTXWO4D7 (download link for v.Beta)
Downloading it now, will check it later on. THX
Was about to create topic but found this and hopefully will try this and hope it works on my XDA Orbit 2. I brought it off Cex from Aylesbury and it needs some love and update as i have Windows Mobile 6.1 (eeurrgh) and brought it off cos i thought i can upgrade to Winodws Mobile so i hope these works well for me.
Any introductions of doing that?
Thanks in advance.
First link didnt work. The XDA tried to block it by restarting it themselves. Tried third time. And unlucky.
Second Link. How can i use NBH file for my XDA?
...
Wrong place dude..
this is for xda orbit 1/artemis..
your looking for xda orbit 2/ poloris..
you need to be here..
Rn
Hi all I'm new here. My phone "O2 XDA Orbit" behaving strangely. Suddenly the sound disappeared and I can not hear phone calls directly into the phone, and any other person hears me not(microphone off), and not just one click sound on the screen. If I restart the phone with USB cable inserted into the phone and computer (on), then the sound occurs again(but not in original style, sound occur in to the back speaker not in front ), and phone function almost normally with microphone (on)>>> until the next reboot when sound disappear again and microphone is off. I mention that;.... connection the phone to the computer can not be achieved in any of this cases. The error code (USB connection) connection on my computer is {Code 10(One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it)} who can not recognize the new hardware. In your opinion of specialists in this field what would be done? I think something happens to the ROM which gives errors of hardware power. The sound occurs when I insert into the phone power charger connector and disappears when the power supply plug out ... Please if you can help me with some guidance what I have to do one upgrade of ROM or something? Specification of the phone is:
[*]IPL-3.04.0001
[*]SPL - 3.04.000
[*]OS - 3.4.0.0
[*]CPU - OMAP850
[*]Speed 201Mhz
[*]RAM 64Mb
[*]Flash 128Mb
[*]Data bus 16bits
[*]ROM 3.4.206.2WWE
[*]ROM date 4/18/07
[*]RADIO Vers. 02.67.90
[*]PROTOCOL Vers. 4.1.13.28
[*]EXT. ROM.Vers 3.4.206.101
[*]MODEL of phone -ARTE200
[*]Platform - PocketPC
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Adryum said:
Funny ...!!! Today I put the phone to the charger and after I removed the plug from the power supply, the sound has returned, but the USB connection to a PC still can not set ...! What should I do? A new version of Windows can install on my phone; without connecting the USB cable to the phone(ex.-of my card micro SD)??
Click to expand...
Click to collapse
have you got activesync or windows mobile device centre installed on the pc?
if yes..
i suggest you buy a new usb cable.
i have this problem with a couple of cables.
"USB DEVICE NOT RECOGNISED"
but when i change to a differant cable, everything is ok.
flashing via micro sd - upgrading windows.
have you done uspl 1.11.cmon?
Thanks for your attention Raving in the first place ...! Data cable has no damage that I checked the same cable with my photo camera and it works normally with PC and I have two more data cables and the problem is the same. It seems weird that the phone do some work once, ...once not. It starts when he wants the sound, and can not find any explanation ... In contrast with the USB connection can not establish anything, something happens to the sound module and USB ...PC see's something, but it's not sure what it is, and says he can not establish connection with the new hardware and it gives me error "CODE 10". in Universal Serial Bus Controller and the Active Sync is instaled on my PC but he don't say a word about this connection...I don't know on what to do...! I must mention that this oddity occurred only three days go and without them I do something wrong ... He grabbed him crazy after a normal operation for a year and a half, because we had no problems with it until now ... I used as a GPS and the phone and I was really pleased with him. By the way, what they mean uspl 1.11.cmon? All data of my phone are in the first post.The phone it was once unlocked by someone else, and now I can use any SIM card from any GSM provider..............I forgot to say that I've rebooted 2 times in general mode and now works but without USB connection sound when he wants it or not................But I think she has lost some registry ...!!!
click 1.11.cmon in my signature.
this will divert you to a tutorial thread.
when you can connect your device to your pc successfully, you should do the uspl 1.11.cmon but not for now. do not try and flash a rom yet either, you will break your device. (thats what uspl 1.11.cmon is for)
id like you to just try the "hard reset".
back up all your data first.
bookmark the page as ill be updating it regularly.
personaly i think its your usb cable, eg:
one of my cables works with a micro sd reader but not my for my device, i understand your cable worked but now does not.. however thats what happened to me.
Sound engages when he wants and where he wants. If I restart the phone, sound disappears and microphone stop; and I can not talking on the phone. Enter data cable from PC to phone, and give the phone restart. Once the phone is starts, sound appear but only in back. When talking on the phone sound very loud and sounds of the touchscreen controls can not disconnect the rear speaker who remains engaged and does not want to disengage it from the normal operating mode. Another job here would be that when inserted in the charger cable, the sound is right: each speaker and microphone or operational. If I remove the plug (charger) of phone then the phone function normally just like before, but without USB connection. If I plug "USB cable data" on the phone, to the desktop I see message "One of the USB devices attached to this computer has malfunctioned, and Windows does Not Recognize it. USB Device not recognized." If I unplug USB cable from phone the sound disappears, and what I have to do is to start over again.......!!!!!!!!!
I tested all data cables, and are ok. The problem is hard. The hardware has a technical failure which somehow blocks the data on USB. Battery power consumption is higher and the battery is discharged rather quickly than it was before the cage. At night when I charge the battery full, morning at 10:00 is only 30/40% of capacity. But what is even stranger is that: when I connect phone to PC, in device manager shows me the new hardware (Mobile Device) but after a few seconds there appear a connection error code (CODE 10) that is the hardware can not start. Active sync has not started when the fault occurred..... In your opinion what should be done in this case? ... Should contact a service or ... in any way I can test something before others get the screwdriver into my phone?
sabih00 said:
hi guys,
i have searched the forums for wm 6.5 ROM, but lots of them are still in beta phase,have bugs or slow.
can anyone give link to a stable WM 6.5 ROM for my xda orbit
Thanks in advance
Click to expand...
Click to collapse
Thanks, i will test...
The connection was made the first attempt. After a week of "digging" through all possible places I noticed that the connection was obstructed by the firewall.PFFFFFFFF ..... Finally found! The FIRE WALL(on PC) settings to be set: ADD PORT------ "Outbound UDP ----5679" -on exceptions tab....See this:http://www.microsoft.com/windowsphone/en-us/howto/wp6/sync/activesync-troubleshooting.aspx?WT.mc_id=FWLink
TKX Raving U're the best...
...
Adryum said:
PFFFFFFFF .....FIRE WALL
Click to expand...
Click to collapse
lol, i didnt think about the fire wall being the problem.. typical that it was something that simple.lol although it did sound like a dodgy usb cable..
thats something ill remember
have a good new year dude!
guys i am having a problem....whenever i try to install any ROM i get error 224 device not responding......my htc is connected through activesync.....what can be the issue...i am using windows 7.
..
raving_nanza said:
ERROR [224] : DEVICE NOT RESPONDING
check the ActiveSync connection and run RUU again. if problem continues, uninstall active sync and re-install.
Click to expand...
Click to collapse
1. unplug device
2. re-connect device to pc
3. wait for active sync/wmdc to connect
4. run ruu
5. if error continues unplug device
6. uninstall active sync/wmdc
7. re-install active sync/wmdc
8. restart pc
9. go to step 1.
Rn
quertz?
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
But i can't change my touch keyboard from qwerty into qwertz.
HKEY_LOKAL_MACHINE\System\CurrentControlSet\Control\Keyboard Layout\"Active" is "00000407"
Thats the German code - but still having Qwerty?
HKEY_LOKAL_MACHINE\HARDWARE\DEVICEMAP\KEYBD\"TaskManVKey" is "0x23"
HKEY_CURRENT_USER\keyboard layout\Preload\1\"default" is "000000407"
What to do?
...
che.bike said:
Hi raving nanza,
you did a great work with BAB v03.
It works great. sometime the touchpanel reacts slow but good.
Click to expand...
Click to collapse
thats Babbeluts rom, not mine!
i merely suggest it to the other users
ill look into your qwerty to qwertz keyboard, when i find out ill post it here and ill update the tips&tricks thread
Rn