Database Users

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

8125 help! G4- wm6

ok so im new at this soo please bare with me
ive been trying to upgrade my phone to wm6
so i found instructions on youtube and followed them good...
then i found out my phone was g4
so i tried to unlock it using this
http://forum.xda-developers.com/showthread.php?t=332320
I used both and still nothing, it will cancel... i used windows xp and i still havr trouble... soo if someone can help me i would really appreciate it
im trying to unlock it so i can update it with the t-mobile wizard
and i want the touchFlo
but i just cant unlock it to get it

let me get alittle more in dep
im using the hard_SPL-G4.exe and it says no device detected
and it is (im using windows xp)
but when i try it with vista it will detect it but wont go all the way through and will leave my 8125 in a white screen
and then the program will close due to problems
i used the soft one but then it wont go though in the end on windows xp

This thread might help you
http://forum.xda-developers.com/showthread.php?t=303972&highlight=unlocking+a+G4+wizard

This one as well
http://forum.xda-developers.com/showthread.php?t=332330&highlight=unlock+g4+wizard

[GUIDE]How did i Brick my Gene and How i restored ( it was much worse )

Well First i was Using OLD Gene P3400
My Gene came with windows 5.1 in it
I have Upgraded to Windows 6.1 1 year Back
Now when i saw 6.5 i thought to use it Downloaded 6.5 ROM Summit's PRO Users WM 6.5 ROM
And i have Installed it as Mine was already SPL'ed for Olip
And after downloading i have directly Started RomUpdate Untility.exe
and My phone was fine 100 % completed and now Restarting
after Restarting i dont know why But it stuck at the Windows 6.5 Splash Screen from 1 hour then i though i should Upgrade the SPL and i have UPGRADED to Oleref some thing
and thus i Bricked MY GENE OLD
it aint working from then
it Wont even Start
SO i have Pressed HOLD Camara Button and Entered INTO Tri Screen Boot Loader
and tried with GENEIMG.NBH strong into CARD Not Helped
Tried mytty not worked
In middle when i try to update the ROMS i used to get INVALID UPDATE TOOL
tried for 3 hours nothing helping
So i search in Forum and found same problem of 3 ppl
there every one wrote the phone was messed up with some ONL some thing u need to give it to Service centre
for and 1 hour i though i should give it to Service Centre
Then Remembered That "HOW LAZY I AM And will i go to Service center and give the phone lol ? "
NOPE i wont im very lazy so i wont
still searched and TRIED HARD SPL V.1.0 olip
and Tried with my phone now its Back to SPl olip
Now what i did was same used Summit's PRO 6.5 WM and tried Sucess 100 % Completed and it was fine
but again same problem It stuck at SPlash screen for 15 mins +
so again entred into boot screen downloaded Original Shipped Asia OLD GENE WM 6.1 and Installed it
And tada it worked like a CHARM
and now MY GENE is BACK to NORMAL
Thanks to Search and thanks for reading all these **** this may be useful to some one
a quote from me "everything is around you try searching it "
So if have any problem feel free to PM Me
Forgot now im HAPPY
its 4 am now lol
Regards
Mr52

mr521427 said:
so again entred into boot screen downloaded Original Shipped Asia OLD GENE WM 6.1 and Installed it
And tada it worked like a CHARM
Regards
Mr52
Click to expand...
Click to collapse
hi can you post the link to original shipped asia OLD gene wm 6.1 ?

after upgrade to 6.5 screen showing windows mobile 6.5 only
I used SumitsProUsersROM_WM6.5_build21815_OldGene_Fixed to upgrade its struck at windows mobile 6.5 screen only nothing happening.
not able to flash again. Aslo want to note that while I was ugrading it shows me something like "sudden loss of power"
Pls help my phone is not working now.
thaks

please read the thread before downloading a ROM. Krazy's this ROM has this problem. try any other ROM for OLD GENE, it will work, if your spl version is .olip

problem with my p3400i
hello sir
i got a problem with my p3400i its shortcut are not working
and the notification error is
\windows\pmnotify.exe
what can i do now pls help me

plz help
plz help me getting out of this problum.i have htc p3400 old.i wrong hspl with orif hspl.then i performed mtty.exe process.now in bootloader [tricolour] screen it shows
spl 1.07. oref
now i dont khnow is it bricked.
or it is changed to new gene.
and what i have to do now.
i have nearly tried all roms .but at startup all show error 300.invalid update utilty.please any one who knows that what has happened to my set plz inform me.is it bricked or what happened to it.and now what i have to do.we have no service center in our country.i am from pakistan

Well Sunny Try Original Rom Now u should get from here please search
Install Original Rom first

upgrading rom

friends...mine is an 64 MB O2 Exec tomal build device
n i tried to upgrade it using Uni_21127v2.3-64 but my phone got
switched off n since then it stays only in the bootloader mode n ntn else happenes even if i remove the battery n again insert it, the device still stays in the bootloader mode...i dont knw wat has happened to it...as i dont havemuch knowlege about it..plz can anyone help me out n guide me...n m also in search of wm 6.1 or 6.5 rom by tomal...any help wud b appreciated....

Welcome to forums
Have a deep read on the Wiki
Good luck,

.... =]
if you cant find the usefullness in the wiki, firstly
Basicly the ROM hasent loaded propperly, but your uni can be saved.
So firstly,
what Operating System (Windows XP / Vista / 7)
1. Windows XP - good, as you can reflash quickly
2. need to load Windows XP as a VM (Vista)
3. Need to load Windows XP as a vm (Vista)
I would download a different ROM just to reflash with, say a tomal rom
then connect your uni to your pc, and let activesync give its nodification, then open the RUU and your uni should load the rom you have selcted to flash,
Flip, that shows how much of an ORD i have... now am writing tuts on re-flashing phone... HELP HELP

rom upgrade on locked sim?
just wanted to ask if one can upgrade the htc universal to wm6 even though it's locked on orange sims.
Thanks

Welcome to forums
More than one can upgrade ROM
Just be sure to read the Wiki instructions
Good luck,

please help... mda vario

hy. i'm a newbie so plz escuze my mistakes and most of all my english.
i have a mda vario or htc wizard 200 as i know.
on the start screen,it shows
IPL 1.06
SPL 1.06
GSM 01.12.10
OS 1.6.2.1
it's a G3 wizard. My problem is that it has the T-Mobile original german ROM and i want it in english. i have read most of the forums here and tried many ideas i found here but nothing helped me so far... i tried cid unlock with lokiwiz,it shows me that is unlocked but when i try to flahh it with the .exe flasher,downloaded Rom-s for it from here,it's not working. I have Win7 now and i tried with Windows mobile device center sync software for win7 and nothing,i tried in Win xp with activesync and nothing,the same simpthomes. It syncs,detects my ppc,i start the RUU,detects the Rom i have,but when i get to the flash window,just after it tells me that the flash process will take about 10 minutes,my ppc disconnects,enters in the bootloader mode,connection is lost and RUU ends with an error window that tells me that the memory could not be read.
My ppc is not sim locked,i can use whatever sim i want with it.
please help me,i am desperate newbie. thanks.

soriyn said:
hy. i'm a newbie so plz escuze my mistakes and most of all my english.
i have a mda vario or htc wizard 200 as i know.
on the start screen,it shows
IPL 1.06
SPL 1.06
GSM 01.12.10
OS 1.6.2.1
it's a G3 wizard. My problem is that it has the T-Mobile original german ROM and i want it in english. i have read most of the forums here and tried many ideas i found here but nothing helped me so far... i tried cid unlock with lokiwiz,it shows me that is unlocked but when i try to flahh it with the .exe flasher,downloaded Rom-s for it from here,it's not working. I have Win7 now and i tried with Windows mobile device center sync software for win7 and nothing,i tried in Win xp with activesync and nothing,the same simpthomes. It syncs,detects my ppc,i start the RUU,detects the Rom i have,but when i get to the flash window,just after it tells me that the flash process will take about 10 minutes,my ppc disconnects,enters in the bootloader mode,connection is lost and RUU ends with an error window that tells me that the memory could not be read.
My ppc is not sim locked,i can use whatever sim i want with it.
please help me,i am desperate newbie. thanks.
Click to expand...
Click to collapse
turn off the device and disconnect the battery as well sim card........ leave without sim card and plug it back battery then take away your device into bootloader mode to reflash again​