Database Users

My wizard died

Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english

which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck

Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)

My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.

alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.

luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.

My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?

alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(

HTC P3300 completly block

Hello Buds,
I've upgrade my p 3300 a few weeks ago with Artemis_touch_1.0_WWE_rapid
IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0
After some days a freeze and soft reset, I made a hard reset, and re-use the upgrade soft ware.
Now its completly block on the boot page with HTC.
I use RUU(in( Artemis_touch_1.0_WWE_rapid) in the Bootloader but it run but after 3% : error 270
If a use a newer RUU ( Release_Aje_fr_1.90Full_YuanYuan) : error 260
please help me I completly lost !
Trux 13
HTC P3300IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0

I had almost the same problem. I intented to change my ROM with an WM6 but it faild and the PDA is some kind dead it freezes in the boot screen. is there some tool to change the rom to an original HTC rom or thre is no help. I hope somebady can help me. the version of the ROM that apears on the screen is:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 4.0.0.0

I've tried to :
Hello...
In bootloader run USPL
It run, to 0% >> to 100% but right after : error 270
Still block...
Trux 13

hmm i don`t know how i can get the device to boot loader mode can u tell me how

Bootloader
Go in ths Thread :
http://forum.xda-developers.com/showthread.php?t=306880
Trux13

hi i solved my problem i used one spanish version of the WM6 for P3300 and it works if u want hire is the link http://www.megaupload.com/es/?d=YZOQEF4H
u can install it and then change to one on english its what i will do today and i saw how to enter in 3 color bootloader mode ON/OFF boton + VOCAL + RESTART then holding the ON/OFF + VOCAL

Stillnot working
I tried your *.exe file but not working
Trux

me too . always the error
ipl 1,14,0001
spl 1,14,0000
g 02 67 90
os 1,14,00
i ll be crzy! jesus! someone help me!
how to run the uspl on this tm phone ?

Has anybody solved the problem? I have exactly same errors and can't do anything

Try This:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing

i tried this already. Invalid certificate any other ideas ?

woojtekr said:
i tried this already. Invalid certificate any other ideas ?
Click to expand...
Click to collapse
Hi
if you need still help GG9735272

the only solution !!!!
woojtekr said:
Has anybody solved the problem? I have exactly same errors and can't do anything
Click to expand...
Click to collapse
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))

savich said:
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))
Click to expand...
Click to collapse
I have the same problem and I've come to believe that this is the only solution. Just one thing: I didn't back up ROM before I tried to flash (talk about a noob mistake).
So, I ask, I plead, I beg... can anyone tell me where to get an original Orange France ROM for the Artemis (SPV M650)?

To my knowlegde you cant backup the rom from your device. whenever you change your rom, use the USPL tool. It is a golden rule until something better is made.
Here are some tips:
First make sure you have a original factory rom from your provider/brand/etc.
Check with a soft reset if code: SPL 1.11000 appears on the the boot screen. (then it is CID unlocked) Any other number and it is locked so you have to USPL first before you change to any custom rom.
If you flash a factory rom then the SPL resets to a non SPL 1.1100 number again. Use USPL to CID unlock again.
Also avoid Vista (especially 64bit) to use the USPL tool. Do it on a windows XP machine. Also there reports of glitches in the usb connection and active sync when doing upgrades or USPL. So keep you system as clean as possible. Dont use a USB hub and disconnect any other usb devices just to make sure.
Also remove your SD / SDHC card before doing a upgrade.
Sometimes the new rom misses some stuff when flashing. When this happens just flash the rom again. But first make sure if its still CID unlocked by soft reseting and check if SPL 1.1100 else use USPL first.
Even if you did all that, there still can be things that can go wrong. So if you absolutely confident to do a custom rom then do it. Otherwise use original upgrades from your provider

brim
help i breaked my htc p3300
jai lereur 270 jai essaiyer tous les rom rien ne marche ::

p3300 work again
p3300 movistar work again

Search but need urgent help please

Hi
I have an O2 Orbit and was attempting to add a few nice cabs to my cooked rom. Anyway it crashed about 6 times running after it had worked fine so I decided to do a hard reset.
Now, when I go into bootloader I get SPL 1.25.0001 and SPL 1.25.0000 with the RUU and USB motifs at the top right and bottom left respectively.
I have tried running ROMUpdateUtility.exe and flashing:
a) the original Orbit rom which just gives a FLASH WRITE ERROR
b) a cooked ROM (but I think I need to USPL) which fails after 3%
How do I re-USPL and then re-flash a cooked ROM...I seem to be able to find small bits of information but not everything I'm after.
I did this about 18months ago so I've completely forgotten again now!
Please can somebody take the time to explain what I need to do.
I can get it into Bootloader and connect it to an XP machine so it's recognised by the update utility.
Thanks for any help.

Follow the links
Follow the link http://forum.xda-developers.com/showthread.php?t=311403
You may need to check about how to recover the bricked device through the link http://forum.xda-developers.com/showthread.php?t=308242
you will be guided on how to unlock before installing any cooked ROM to O2 Orbit or Artemis.
Hope the above clarifies and solve your problem.

unfortunately the first link doesn't help as I can't get into my WM device's OS for it to actively connect through Active Sync.
The device was already unlocked as I had a cooked rom on it before a hard reset (does this matter). I've tried the WM5 and WM6 o2 orbit roms and neither flash...both fail on 5% with FLASH WRITE error.
Please if anyone else can help I'd be greatly appreciative. I've lost my entire phone as it is. My partner has just lost her father (my father in law to be) and we have been staying in constant contact whilst she is away.....I can't do without a phone.
Here's hoping somebody takes pity on me and gives me a hand.
Currently sitting at bootloader...can connect with mtty but no idea what to do with it (password of BsaD5SeoA doesnt work)

Right,
I'm at my bootloader and I also have a non-SDHC microsd card sitting with me with an ARTEIMG.NBH on it...it starts to flash when using it then says "SD FAT failed!!!"
Please help!

Anyone? Dire Straits lives here!!

HTC ELF 0300 problem!

I have HTC ELF 0300 that freezes on the T-mobile logo when i try to power on!!!
I tried with hard reset,but that not helped.
I can't make ActiveSync connection with my PC!
I try with connecting the phone in bootloader mode,but still can't make ActiveSync comunication!
Any advice???

Did you manage to see a screen that says 'smart mobility'

jeremy89632 said:
Did you manage to see a screen that says 'smart mobility'
Click to expand...
Click to collapse
No! It just goes to operator logo and blocks on it!

When you are in bootloader mode.
Does windows xp or vista detect that?
Activesync ONLY LOADS in normal mode, not bootloader.

jeremy89632 said:
When you are in bootloader mode.
Does windows xp or vista detect that?
Activesync ONLY LOADS in normal mode, not bootloader.
Click to expand...
Click to collapse
No,windows doesn't detect the phone in bootloader mode!

Weird.
My vista pc will.
But have to install Windows Mobile Device Centre first.

When I connect in bootloader mode I tried with many Rom updaters but every time I get this message 'The update utility can not be used with your PDA Phone.Please get newer update utility'
I tried with update utility 3.27.4.3 an lower versions.
Is there newer version?

What is your phone's IPL and SPL?
Before you start your phone, press the power and camera key together, it will boot up a multi colour-ed screen and it will report the IPL and SPL to you there

jeremy89632 said:
What is your phone's IPL and SPL?
Before you start your phone, press the power and camera key together, it will boot up a multi colour-ed screen and it will report the IPL and SPL to you there
Click to expand...
Click to collapse
IPL 1.13.0002
SPL 1.13.0000
any idea what to try next???
thanx for your help bro anyway!

Can you sync your htc to other pc's?
Reinstall activesync.
and your ipl and spl is way too old.
During the meantime, read the other threads.
Will be going to camp in 14 hrs time and its almost 1am here.
So yeah.

I've tried to sunc with other PC's too,but the same result! when i start some Rom Update Utility it gives me that I should try with newer version.

well, if that can detect the newer version!
Bingo!
you computer can read it.
Alright, update your IPL and SPL to 3.10.
and its avail at htc upgrading forum.

HTC ELF 0300 Error
Hello somebody could help the other day I came across a ELF0300 phone and also the problem that would crash the machine operator in the Logo.
inquired the previous administrator of the system can not be installed on it.
handheld device is excellent by the way the externally,and we need to somehow fix
Bootloader mode writes
IPL 2.26.0002
SPL 2.26.0000
but quite interesting if you install this dream running 100% and then upgrade error
Activesync does not do anything
Thanks in advance for the help

HTC Prophet won't load Windows :(

Hello everyone!
I got a HTC Prophet with english windows mobile. I've wanted to install a german ROM, and used this:
http://www.handy-faq.de/forum/htc_p...ophet_touch_ix_rom_deutsch_download_1005.html
I've runned a .bat file and the installation startet. But then i closed the window with the installation insinde (undeliberate). and now the prophet won't load windows. it always stops at the boot screen, where the infos are:
IPL 2.15.0001
SPL 2.20.0001
I can run the BootLoader mode and connect the Prophet to my PC. on the left bottom it says "USB" but when I run the installation again it says "no device connected".
i got windows 7 ultimate in 32bit version.
I hope you can help me, 'cause it's the phone from my dad and i won't get him angry
Greetings from Germany!
Bianca

geffi said:
Hello everyone!
I got a HTC Prophet with english windows mobile. I've wanted to install a german ROM, and used this:
http://www.handy-faq.de/forum/htc_p...ophet_touch_ix_rom_deutsch_download_1005.html
I've runned a .bat file and the installation startet. But then i closed the window with the installation insinde (undeliberate). and now the prophet won't load windows. it always stops at the boot screen, where the infos are:
IPL 2.15.0001
SPL 2.20.0001
I can run the BootLoader mode and connect the Prophet to my PC. on the left bottom it says "USB" but when I run the installation again it says "no device connected".
i got windows 7 ultimate in 32bit version.
I hope you can help me, 'cause it's the phone from my dad and i won't get him angry
Greetings from Germany!
Bianca
Click to expand...
Click to collapse
Hi this is a easy problem to fix dont worry but first u need to read this http://forum.xda-developers.com/showthread.php?t=353547 you need to hardspl your device first then install the NVID rom in the link read the recovery solutions carefully oh and about active synce try this
Go in to Active Synce settings and uncheck allow usb connections that will help to detect your device when flashing the NVID rom after that just use any flashing tool to install the rom on your device problem solved just read the link if u dont understand as this happened to all of us before so we understand how u must feel
Hope this helps

Heya and thanks for your answer!
I did read the terms of use in the post u linked, but I got always the same problem:
No device is found. on the BootLoaderScreen it says "USB" and Windows 7 detected the Mobile Phone.
But the HardSPL didn't found the phone
I try to take the battery out and put it in after one minute, but it didn't work

geffi said:
Heya and thanks for your answer!
I did read the terms of use in the post u linked, but I got always the same problem:
No device is found. on the BootLoaderScreen it says "USB" and Windows 7 detected the Mobile Phone.
But the HardSPL didn't found the phone
I try to take the battery out and put it in after one minute, but it didn't work
Click to expand...
Click to collapse
Did you try flashing the NVID - AKU 2.* WM5 rom for recovering your Prophet on your device first then hardSPL your device? you need to install the rom first then hardspl it after that flash any other rom here http://www.4shared.com/file/57952591/3955ed98/NVID_RUU.html?dirPwdVerified=2948f2e flash this to your device and remember to uncheck allow USB Connections in active sync and just it should work if u still need more help al be happy to help you out and since ur using windows 7 use this tool to flash any rom to your device ok http://forum.xda-developers.com/showthread.php?t=534707 since am using both vista and xp and they work well so remember flash the NVID rom first then hardspl and try flashing back the rom you wanted to use on your device ok

hey!
i installted Windows XP and then load the HTC Prophet in BootLoaderMode.
I do HardSPL and it works. Then I install thisNVID. The phone rebootet, but windows didn't load. when i try to install the rom (i posted the link in first post) but it says already, that no device is connected.
the phone didn't load windows

geffi said:
hey!
i installted Windows XP and then load the HTC Prophet in BootLoaderMode.
I do HardSPL and it works. Then I install this NVID. The phone rebootet, but windows didn't load. when i try to install the rom (i posted the link in first post) but it says already, that no device is connected.
the phone didn't load windows
Click to expand...
Click to collapse
Sorry but first you need to recover your device by first installing the NVID rom and good u have windows xp did you did what i said about active sync uncheck allow usb connects then flash the NIV rom then use lazytool thats what i use on my windows xp to flash the rom u wana use what happened when u try to install the NVID rom? first you must manualy go too the bootloader menu in other to flash it you know reset the device and hold both the commanager and camura button until you enter the bootloader menu then flash the NVID rom if it works then do a hardspl then flash any roms using lazytool it should work when u said the phone rebooted but windows did not run what did you see on the screen? after the reboot? also the NVID rom is windows mobile 5 so you device should boot up windows but al look into this for you ok
PS this is important you should know that your device is G3 or G4 and from the looks of you spl it looks like a G4 device this is very important beouse if u flashed with G3 you can damage ur device but dont worry the guys here have managed to fix this so if ur flashing any rom use the G4 option ok but please look over these instructions http://forum.xda-developers.com/showthread.php?t=353547 as they helped me when i had the same problem
I just Private message you check ur inbox