Database Users

Revert back to Windows Mobile after NAND Android Install?

I've been using senseTattoo for a few days, and was wondering: Is it possible to revert back to Windows Mobile? If so, how?
Any replied will be appreciated, thanks

just flash back to your prior windows mobile rom. get into tri-color screen by holding down power and camera while you press and release the soft reset button. then flash away.

Did somebody try it? I hold power button with camera, tri-color screen was shown, thne I press and release soft reset button and from this time I have only black screen nothing working - HTC Polaris

tominga said:
Did somebody try it? I hold power button with camera, tri-color screen was shown, thne I press and release soft reset button and from this time I have only black screen nothing working - HTC Polaris
Click to expand...
Click to collapse
Instructions might be different for POLA, check your forum.

tominga said:
Did somebody try it? I hold power button with camera, tri-color screen was shown, thne I press and release soft reset button and from this time I have only black screen nothing working - HTC Polaris
Click to expand...
Click to collapse
Did you flash a Windows Mobile ROM?? Sounds like from your post you didn't, so I'm just making sure. And if you want further support, I would recommend you go to the HTC Polaris section
http://forum.xda-developers.com/forumdisplay.php?f=397

yes , retorn to wm6.5 after on instal nand android on htc hd2. detail on my e-mail [email protected] .am reusit sa instalez nand android pe al meu htc hd2. apoi mam intors la wm6.5 cu ship rom . easy. is possible

I enter bootloader mode and then run ROMUpdateUtility.exe
but i get error message --> error [260] connection
what should i do?
thanks

finally, succeed reverting back to winmo
flashing by SD card because i coudn't flash by ROMUpdateUtility

Need Help!!!
Im trying to get my HD2 back to windows 6.5. Would you tell me how you did [email protected]

acooke1105 said:
Im trying to get my HD2 back to windows 6.5. Would you tell me how you did [email protected]
Click to expand...
Click to collapse
Wrong forum, man. Take a look in the hd2 winmo section.
Sent from my DROID2 using XDA App

[Q] How To Upgrade MAGLDR From Android

I was wondering if anyone out there can help me.
Im currently using Magloader Version 1.11 by cotulla 2010 and i would like to upgrade to MAGloader Version 1.12 so that i will be able to run Windows Phone 7, though i can't do this because in order to upgrade Magloader i have to be connected to Windows Mobile Device Center and i cant connect to it since im running NAND Android not windows mobile.
Can anyone help me ? Thanks!!
Isaac

Read
Look at this thread
http://forum.xda-developers.com/showthread.php?t=912416
You install MAGDLR 1.12 the same way as you installed MAGDLR 1.1.
Read through the forums and use some common sense.

Hopefully a slightly more helpful response...
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.

shovels said:
Hopefully a slightly more helpful response...
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.
Click to expand...
Click to collapse
Thank you so much for your help ! Will try to do asap, so once i enter the bootloader screen windows will detect my phone and i can update my Magloader ?? Thanks a million for your time and help !

Problem with flash, "1234 fatal hit 4"

hi dudes i am new here and i think i fu*ked my hd2 up... can you guys help... what should i do... Flashed failed on PC and now i get fatal hit 4 on my hd2... what should i do!? How do i reflash it?

Hmmm, i would start right from the beggining again.
Re-flash MAGLDR by holding down the volume button whilst pressing on.
Then, re-flash WP7.
Alternatively use the MAGLDR youve got, and hold down the on off button and go to flash on the menu (cant remember exactly what it says on menu

If I were you I'd do the following. Might seem a lot like overkill, but should work 100%.
1 - Go into bootloader (press and hold vol down button then power on as normal)
2 - Flash any WM6.5 ROM
3 - Charge the battery to 100%
4 - Perform a Task 29
5 - Flash a 2.xx.50.x radio
6 - Flash Magldr
7 - using vol down button select option 5 from magldr menu
8 - when phone says USB flash WM7 (suggest YukiXDA for the mo until a ripe MANGO released)

i made it but can you give me a good wp7 rom and radio file? ty

This Is The Most Stable N Outstanding One I Saw And Im using at the Moment
http://forum.xda-developers.com/showthread.php?t=1080950

and one more question... Can i go back in windows mobile 6.5 after i install wp7?
i installed everything but when i was installing the WP7 rom it got some error and now i start the device says go go go in magldr mode and then shows a black white picture with mobile and a lap top and stays like that 5 mins and then restarts... what should i do? It drives me crazy...

problem with hard reset
Can some one help me with hard resetting windows phone7
1. On magldr screen, when I see "1234.." etc, I pressed and hold volume down key, I was expecting to see some screen which says press vol- twice to clear data. Instead I am seeing the main boot screen with four colour bands from top to bottom.
Please help..
Thanks in advance
Kishore

Hard resetting WP7 on HD2
Can some one help me with hard resetting windows phone7 on HD2
1. On magldr screen, when I see "1234.." etc, I pressed and hold volume down key, I was expecting to see some screen which says press vol- twice to clear data. Instead I am seeing the main boot screen with four colour bands from top to bottom.
Please help..
Thanks in advance
Kishore
EDIT:: I got it resolved, I could not figure out the way I need to press both the vol+ & vol- button at once during the 1234 GoGo screen... It worked

what do you want? cant understand you... You want to clear data or hard reset windows 7 phone... You need MAGLDR just when you flash the windows 7 phone rom...

king_slavcho said:
what do you want? cant understand you... You want to clear data or hard reset windows 7 phone... You need MAGLDR just when you flash the windows 7 phone rom...
Click to expand...
Click to collapse
Pardon for not being clear to you...
I got it resolved though, I could not figure out the way I need to press both the vol+ & vol- button together during the 1234 GoGo screen... (earlier i was pressing either vol + or vol- but the requirement is both vol+ and vol-)
Regards
Kishore

Fatal hit 4
Hey guys,
After a while i decide to go back tom my HTC HD2 and install the WP7 rom but like some others im facing the "1234 fatal hit 4' issue. Has anybody being able to adress the problem?
Thanks in advance.

[Q] Can't get to Bootloader

Hey Guys. I was hoping someone could help me with my problem.
Currently my HTC HD2 is running cyanogenmod7 using MAGLDR 1.13.
I want to switch back to winmo 6.5 to start fresh and have read tutorials that i need to enter bootloader ( the red, white, green screen thingy) to establish a connection with activesync. But the problem is that i can't actually get into bootloader and i have tried volume down button with the power button combo and it doesn't seem to work.
If someone knows how to get to bootloader then please help.

While the phone is off... do what you did... hold power and volume down buttons...

Yes, i tried that 20 times and it doesn't work

Roger9546 said:
Yes, i tried that 20 times and it doesn't work
Click to expand...
Click to collapse
Does the volume down button work on your HD2? Sounds like it does not.

That's the strange part. My volume buttons work perfectly in Android and Magldr. I don't know what's happening

switch off the phone and open it again while you are holding the end call button
you will go the magladr menu , i thik you can find something there to take to the bootloader

the_entity said:
switch off the phone and open it again while you are holding the end call button
you will go the magladr menu , i thik you can find something there to take to the bootloader
Click to expand...
Click to collapse
No no no no no and NO!!!!!!!!!!!!
There is nothing in MAGLDR that can make your HD2 go into bootloader. The only this.g that can get you into the bootloader besides the external hardware buttons is the bootloader.exe that can be run from inside Windows Mobile. It can only be run from inside Windows Mobile. MAGLDR is a custom bootloader that runs after the HSPL bootloader and has no way of communicating with the HSPL bootloader.
At the OP, you may have a faulty volume button ribbon that is causing you not to be able to boot into the bootloader. Check out this thread you will see what I mean. Read post #10

Boot loader mode
Bootloader mode is handy for checking the HD2's version of Hard SPL as well as the installed ROM and Radio versions,and also for ROM or Radio flashing to the HD2. I sometimes use the Bootloader method to flash ROMs as it saves connecting to Activesync/WMDC because the PC recognises the HD2 as connected via USB. It is also useful for flashing a ROM or Radio version if the battery charge is less than 50%, as it ignores the 50% charge warning that is normally displayed when flashing if the HD2 is low on charge. Never use this method if you have less than a 30% charge as you will be in deep trouble if the HD2 runs out of power while flashing a ROM or Radio version!
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.

AlexALP said:
Bootloader mode is handy for checking the HD2's version of Hard SPL as well as the installed ROM and Radio versions,and also for ROM or Radio flashing to the HD2. I sometimes use the Bootloader method to flash ROMs as it saves connecting to Activesync/WMDC because the PC recognises the HD2 as connected via USB. It is also useful for flashing a ROM or Radio version if the battery charge is less than 50%, as it ignores the 50% charge warning that is normally displayed when flashing if the HD2 is low on charge. Never use this method if you have less than a 30% charge as you will be in deep trouble if the HD2 runs out of power while flashing a ROM or Radio version!
To place the HD2 into Bootloader mode, remove the HD2's back cover hold down the volume down key, now press in the red reset button under the back cover to the bottom left of the SIM, release the soft reset button but continue to hold the volume down key in until you are presented with the tri colour bootloader screen. To exit Soft Reset the device.
Click to expand...
Click to collapse
Hi!
I try this so many time, but my hd2 does not step in bootloader. Have you got some other idea??

I have exactly the same problem, help!

Roger9546 said:
That's the strange part. My volume buttons work perfectly in Android and Magldr. I don't know what's happening
Click to expand...
Click to collapse
Can you get into the windows start- settings - system? If yes, there is an app that says "clear storage memory", which brings you back to the factory settings when you bought it. It's worth a try.
Entering bootloader screen is sometimes difficult: press and hold the volume down button and then press shortly
the power button, this should bring you to this screen. If it does not, remove your battery for at least 10 minutes and try again.
Good luck and regards, Kuzibri

I had the same problem ...
I could not enter the bootmanager in android brief button press to end a call, we moved the menu to shut down, reset, etc, the same menu that appears when you hold down the button longer to stop calling ...
This defect appeared to me after I lay HD2 due to large changes in ambient temperature ...
After a few days of research, opening, drying I removed the defect, so I pulled out and cleaned the keys below the screen (Home, Menu, Back, red and green) and wipe the foil that these pressures are the same buttons ...
My HD2 has been working for 2 weeks with no errors

same here but ...
to get in to bootloader i just discovered a different (strange)way ... from winmo , with back cover off press red reset button and imediately while reseting press volume down ... this is my only way to get in to ... otherwise , all the keys are fully working when in windows mobile .

very strange
all the keys includind the volume down key, works well inside windows, but I just cant go to bootloader.
I will dismante the phone, wash it and dry it, to see if something changes,

I have problem getting into 3 color bootloader also, but its because my voulme down is broken/ doesn't work anymore. Any other ways besides the volume down button?

Jcamacho228 said:
I have problem getting into 3 color bootloader also, but its because my voulme down is broken/ doesn't work anymore. Any other ways besides the volume down button?
Click to expand...
Click to collapse
only if you are currently running winmo 6.5, , theres a winmo app to restart into bootloader.
alternatively, dismantle the phone and short the voldown connections.

bootloader&spl
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom...if so, how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl... Thanx

foysyl said:
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom...if so,
Click to expand...
Click to collapse
phone off
press and hold voldown
tap and release power
keep holding voldown.
No, the tmous doesn't use a different method than the regular hd2.
how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl... Thanx
Click to expand...
Click to collapse
all stock roms include an spl, i think YOU mean ''or stock rom with hspl.''', , no, there are no stock roms that include hspl.
there is only one way to apply HSPL, , and that's through bootloader.

bootloader prob. on hd2 usa
How to enter bootloader(tricolor scren) on hd2 t-mobile-usa, i tried wth vol down key but no respns. I thk may be another key for hd2 t-mobile-usa. Does any one know? Or thr is no Spl with ths stock rom¡*if so, how to instal Spl on hd2 t-mobile(1024) or stock rom wth Spl so that i can instal Hspl¡* & whr i can get bootloader.exe for hd2 - wp6.5
Thanx
---------- Post added at 05:54 PM ---------- Previous post was at 05:30 PM ----------
But cant get its bootloader by holding vol down key wth power key at a time thn pres reset butn.
Is thr any soft/bootloader.exe for entering hd2's bootloader through pc or frm phn(hd2-usa)? If so thn pls giv the link. Or is needed to re-instll stock rom over prsnt stock rom
Thnx([email protected])
---------- Post added at 06:12 PM ---------- Previous post was at 05:54 PM ----------
samsamuel said:
only if you are currently running winmo 6.5, , theres a winmo app to restart into bootloader.
alternatively, dismantle the phone and short the voldown connections.
Click to expand...
Click to collapse
Need ths App...pls giv me the download link

Try this!
Hi, I had a similar problem where I could not enter the boot loader. The solution I found that worked for me was provided by: broncogr on another thread discussing a similar issue with the DHD ( http://forum.xda-developers.com/showthread.php?t=889567 )
"restart the phone
when the capacitive buttons light is off immediately press and hold volume - button and keep holding until device is in bootloader
cheers " - broncogr
Hope this helps someone.
Ez

[Q] Flashing the Blackstone

Hello, I have an HTC Touch HD with the 1.56.401.0 (43972) WWE Rom and SPB Mobile Shell 3.5 on top. I want to breath new life into it and searching for a suitable ROM to flash it. The main reason I haven't tried so far is that my Vol Down key is busted so I can't do much. What I want to ask is if there's another way to do this through connecting my htc to a desktop pc and what steps do I have to take to flash it successfully. Sorry if this looks like a stupid question but since my htc has serious stability issues I have to ask for help.
Any help or guidance/tip would be much appreciated.
Thanks

You need the Vol Down key to work in order to flash.
The phone must be in "bootloader" (3-colour screen) to flash.
Bootloader mode is done by pressing Vol Down + Power key combination.
Try and see if you can make the Vol Down key work without the back cover by poking a pin directly at the Vol Down contact. Sometimes it will work.
Cannot flash if you cannot reach the bootloader mode.

Thanks chan.sk for the head's up. I'll try and see what happens.