Hello, please can you help me! I only had my PDA repaired a couple of days ago, i needed to unlock it and i used your intructions for unlocking the XDA II but it did not work.
After following your instructions and opening the program xda2unlock and typing "yes" the program came up with the message:
"ERROR: OpenComport \\.\WCEUSBSH001 - the system cannot find the file specified"
The PDA is showing "serial v1.06" and "usb v1.06 when in cradle, it wont do anything like before i had to get it "reflashed" by the company.
What can i do??
Thank you!!
Nieko
connect it to usb and falsh a rom on it
the wifi and the readme of the rom file describe step by step how you do it
Struck on Serial
I do have the same problem. What would be the best ROM plz. All the ROMs I downloaded gives error as "102 Image File Checksum Error" or Language ID Error". Pls give me a good link for a working ROM.
Related
i dwonloaded and installed T mobile rom from this site
My device is Q tek 1010
i cant install any other rom as this error message appears each time i try to upgrade the rom
"Please find the error message attached"
I need help as the message read the device is not connected however its will connected and active sync can see it fine
Please advice what to do
Regards
The ROM you have currently installed prohibits flashing via Active Sync. You have to flash via SD-Card and Bootloader.
Take a look here how to do this....
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashSD
HTH
Stefan
Hello,
I was trying to upgrade the O2 XDA II and in the process, it created an error. The upgrade was terminated, when I try to hardest the device and put it in boot loader the screen went blank. The Mtty.exe doesn’t work with USB anymore it gives an error “USB port can not open”. Any suggestions will be appreciated.
Thanks
Hello, i tried to install wm6 on my qtek 9100, first i have followed this guide: http://forum.xda-developers.com/showthread.php?t=298613 , but the wizard_love rom failed, and then i CID unlocked my phone and that worked fine but then when i tried to install T-Mobile 2.26 rom" from the link: http://rapidshare.com/files/38880130..._ship.exe.html an error message comes up after the instal has
reached 1% i think its "error 326: this NBF file can not be used for your PDA phone, please check your PDA file" and then the instal does not continiues. So i installed button_rom again from the gudie and the install worked fine, but when i restarted my phone i gets stuck in bootladder screen (not the 3 colored screen) and there are IPL/SPL 1.01 but i dont came any longer, i tried to reinstall button rom but it´s the same thing, i get stuck and my phone wont go in to windows...
What shall i do??? pleease help me i have just buy this phone for 400 dollars, so i must make it work again, the best is if i get the orginal swedish rom for my qtek 9100 pleeeease help me please
Sincerly yours// Johan
Edit: almost every rom i try to install, it gets stuck and a error message comes upp: Error 326 ( i think) please check your NBF file or something like that, what is the NBF file? and how do i fix it?
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Have you tried updating to the latest version of Active Sync on XP
or following the guide for Vista
Take off battery. wait for about 10 hrs. put back battery and switch on the power.
Thanks for the tip's
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Furkinl said:
I have tried Activesync on XP and Vista still does not work.
I have removed the battery for two days and recharged it through the cradle, on returning the battery and switching on. It returned to the serial screen.
I tried flashing with the following rom : [Maxishare_net]alpine-1.11.171-radio-1.04-bluetooth-patched-camera-fixed again i get the message it is the wrong ROM??
I can not understand why I keep getting the wrong ROM message as it is definetly a XDA IIi PH10C
thanks anyway
Click to expand...
Click to collapse
erm u are trying to flash on a pc running vista?? thats your problem, u cannot flash on a vista pc, xp home/pro ONLY!
Thanks for the advice, tried on XP and it worked fine, it would seem that activsync was not required in this case. At least my XDA is ALIVE for now.
many thanks
You simply could revive it again by Resetting it via the stylus
thnx 4 all the soloutionsss
i had same problem , but once i tried it on xp, its works for me, my ppc now is refresh installed,
thnxx
qtek 2020i
for information the french rom is available on this place http://www.planete-htc.com/index.php?mod=download choose dangaard section there is two files to download
1. choose 2020i dangaard rom
you can not use it
2 download the radio file
it contains an exe called upgradeut make it in the directory of your dangaard folder and you will be able to flash it
it work also for pda stuck in serial usb
voila
qtek 2020i
radio file 1.04 two mega
do a hardware resett and it should be the phone back to defaults
XDA IIi V 1.01 Serial /USB
Hello,
I tried to update my XDA IIi from a new rom version found at o2.ie website but my XDA IIi is stuck and showing Serial on top and v 1.01 at botom. When i attach it with cardle it shows USB instead of serial.
I have tried Almost everything that i found on this forum in last three days.
Hard reset / soft reset/ new installation using different version etc.. but nothing worked for me..
Now I am really confused and can't find what to do.. Can any one from XDA gurus/ developer help me and sumarize what should i do?
Thanks in Advance
Zeeshan
Yes, i have the same problem i did exactly what was done above me pls can someone help!!!!!!!!!
Furkinl said:
Hi all, Hopefully some wise person can assist me.
I downloaded a ROM update for my XDA11i from this site :Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed which was highlighted for a Alpine. However on running the update you get a picture of a MDA and a message "The ROM upgrade utility does not design for your device. Please get proper ROM upgrade utility and try again"
Unfortunatly my XDA11i is now stuck on a blank screen with Serial V1.01 and is not recognised by activsync or My computer. However in the cradle the screen shows USB V1.01
I have tried installing the official O2 ROM update: AP_O2UK_11100_169_10000_ShipXdaIIi but get the following message Error 101: connection error. I assume because my XDA is not recognised by Activsync.
I have spent days trawling the forum and trying the various solutions to no avail. Most of the links are dead as in archive.
1. On reset and hard reset the serial text only dims.
2. I tried the process posted by CelticLo and copied a ROM image to a SD card, however again on hard reset the sserial text only dims.
Any assistance would be very much appreciated.
Click to expand...
Click to collapse
Where can I download this rom?
Alpine_Ext-1.11.162_Radio-1.04_O2stuffstripped_Camera_Fixed
Thanks in advance
Chet
look and lern
put qtek 2020i in stativ (conect to pc via usb)and push power ( on screen will apear USB and v1.01), and you dezarhive :astel_wwe_11100_112_10200_ship, and doble klik on AlUpgradeUt and bios at ppc wil be update !!!!! This is all, the ppc will be now reinstaling, be patient and wait until will be reinstaled (25 min)
I have got hold of a T-Mobile Ameo that's gone wrong whilst upgrading/unlocking, I believe they were using the Olipro way (which I've successfully done fine myself in the past) and it's now stuck in the multi colour bootloader screen which displays:
ATHE100
IPL-v2.02
ATHE100
SPL-v1.10.RP00
And although it shows USB when plugging it in to a computer it won't connect to ActiveSync so I can't get to the stage where I can re-flash it.
I have tried the hard reset by holding down the volume and pressing the reset hole, and I get to the prompt:
Press ACTION to restore factory default
Press Camera Key to exit
I then press the little nipple button down and it displays:
Restore default complete
Press Power Key to boot
Press CommManager Key to format micro drive
I press the Power Key and I'm back in the multi colour boot loader back where I started, and I canot connect to ActiveSync to reflash.
Any help to turn this paper weight back into a useful device would be appreciated...
exactly the same problem here.
any guru with a solution ?
seckt0r said:
exactly the same problem here.
any guru with a solution ?
Click to expand...
Click to collapse
Hi seckt0r,
have you tried reflashing the original rom for your device while connected to your computer in bootloader? ftp://ftp.xda-developers.com/Athena/Shipped_Complete_Updates/
another idea would be to try sd card flashing,(see the wiki) but you would need to extract an image from the flash utility.
One thing to note is you couldn't flash any of the newer roms as you are probably not unlocked
lakeman,
Thanks for the tips and sorry for the late reply.
I did figured out how to make it work again, and played a lot with the device
Already delivered back to the 'client'...
Active Sync issue is solved !!!
Active Sync 4.5 had changed the way it connects from USB Serial Sync Mode to RNDIS Sync Mode. So it can cause problems in connecting with PPC. Try install on your PPC the "ActiveSyncMode.sa.CAB" that you can easily find on Google & run it. Hope this might help.
same problem here i tried to upgrade with orignal rom tmobile uk but its show invalid vensor what can i do plz help thnx
got your msg ahmerp but I don't use MSN
have you tried some of the other shipped roms
if that fils you could try cmone s mtty solution to rswrite the vendor id
seckt0r said:
lakeman,
Thanks for the tips and sorry for the late reply.
I did figured out how to make it work again, and played a lot with the device
Already delivered back to the 'client'...
Click to expand...
Click to collapse
Please help me to sort out my ameo problem some one flashed with with wrong rom now phone shows only volume icons and whenever i try to flash with tuk roms it always give me error invalid model id e.g
Check post 33 on this thread http://forum.xda-developers.com/showthread.php?t=387454&page=4. You MUST use Windows XP with SP2 optionaly SP3 for this to work. If you need mac file for SPL1.2 send me email.
ameo stuck on bootloader after trying to unlock with athena unlocker
my tmobile uk was on rom 1.12. i tried to unlock and it went faulty on step 1. now it boots only in bootloader mode tri colour screen.
any tmobile rom gives invalid vender id error 294.
anyone can provide me with the original 1.12 tmobile uk wm5 rom?? also anyone cna help me online to change vender id using rswrite or pdocwrite.
Ayyub
hafizayyub said:
my tmobile uk was on rom 1.12. i tried to unlock and it went faulty on step 1. now it boots only in bootloader mode tri colour screen.
any tmobile rom gives invalid vender id error 294.
anyone can provide me with the original 1.12 tmobile uk wm5 rom?? also anyone cna help me online to change vender id using rswrite or pdocwrite.
Ayyub
Click to expand...
Click to collapse
Can you post what is written on the bootloader screen?This will help define what rom you need to flash.
thanks lakeman
my bootloader tri color screen shows
I hv a new htc Athena (ameo t mobile uk locked).
I was trying Athena unlocker by olipro. I hv used this on a number of occasions and no problems.
With the present one it was on rom 1.12 tmobile uk and while doing Athena unlocker it crashed on first step.
In bootloader mode it shows
Athe100
Ipl-v1.00
Athe100
Spl-v1.10. RP00
It keeps giving invalid vendor id error 294 when I try to flash tmobile original rom
I have read olipro message who say that I can only repair this via pdocwrite. Apparently it’s the spl that’s corrupt so I need to repair this.
I will be very happy if u can help me with a step by step guide to repair the spl using pdocwrite or rswrite to change vender id.
I am using windows xp or windows 7 and I hv tried mtty and I can successfully connect to Athena and do info 2
It shows level=ff ie it is still locked cid.
Wdata also seems to work but even after password says pass I do not really know how to change the device id or vender id
Device id shows HTCS Þ?ÒtHTCE
I am told y olipro that this device id or spl can only be repaired via pdocwrite.
How can I do it..
Pls help me u can email me on [email protected] or hotmail.com and can add me so u can please provide me with a step by step guide repair my athena ameo
Ayyub