My SX66 is running WM6.1 ROM from sun_dream.
Every are smooth except one problem:
When I set the Caller ID service to "no one", I can not make any call.
I do not know why. I test my SIM with another phone, calling works normally. So I guess the problem is on the ROM.
I did search the forum but did not find a clue.
Any suggestion/solution are really appreciated.
Thanks,
it is possible that the network setting for caller id varys from country to country but for germany for instance the code is 31.
for getting the status dial *#31#
for temporary sending of your callerid dial *31#
to disable callerif dial #31#
and to get the status of incoming id dial *#30#
either that works for you or you look up the codes for your country and/or carrier and try them, that way, you can tell whether really the setting is broken in the rom or just not compatible to your network and adjust it.
Thank you for quick reply.
My network uses code #31#, and I tried it but could not make the call. The same with setting "No one"
I guest that the problem is with the ROM.
have you tried upgrading your radio rom? the newest one is 1.15.00 and maybe that will do the trick. or you sim unlock your device, or you try another sim card in your device. you know, the possibilities for what went wrong are pretty limitted, but i actually would blame the rom last, since that really hardly affects the calling.
Related
I have T-Moble here in the US and updated my Pocket PC Phone edition rom versio 4.00.16 ENG and noticed they have this call barring feature in the phone settings that lets you bar incoming or aout going calls but to activate you have to enter a call barring password does anyone know what it is.
i never used or tried it, but i was told its the last 4 digits of your social securty # or last 4 of your fone #
I tried both abd it didnt work but thanks for the info
I always thought call barring was done through the sim/service provider password.
T-Mobile also uses 1234 as a default password often.
also try 5678
Thanks again people i will try thpse suggestions today
Where did you find a 4.00.xx update for Tmobile? I just checked their site and they still had the old Nov 2002 3.16 code up there.
Thanks,
If you look at the ROM Update section of this forum you will see we have easy access to various 4.00.xx ROM updates.
SIM PIN 1 & 2
Ok, I had an experience earlier this year where one of my t-mobile phones (not the PPC) wanted "Sim Pin 2" to access a feature. I ended up getting my sim pin blocked and called up t-mo support. After a little bit of "Try to get the information out of the dumb support person" I finally had the person ask me "Well, I could give you PUK1 and PUK2, if you think that would help", I said i thought it might, and she gave me the two keys to the kingdom (Along with what SIM PIN 2 was originally, just a random string of number). The moral: Call T-Mobile, tell them you have a feature that you can't unlock and that you think you've screwed up your phone bigtime. If they ask if you want to send it in, say no, that you think you can fix the problem if they give you these weird PUK numbers or PIN numbers. They'll probably just be happy to get you off the phone, and these might be the numbers you're looking for.
Tmobile has a special plan called the "data-only" plan that automatically blocks all incoming or outgoing calls. However, it still allows emergency dialing (911) and 611 calls... Just call a rep and have them set you up with that plan! Everything costs the same...
As I am using the below mentioned OS version and Radio. I have a call barring for all outgoing INTERNATIONAL calls. Whenever I need to dial an int'l call. Thru the built-in selection for disabling the bar code, this options pops an error saying to check my phone settings!
But when I use the dial buttons to press the keys combination which my ISP provides #331*----# (dash are digits), this works on the spot in either cases, the on and off!
Any help
hello,
i have t-mobile mda II (under wm5 ,i think software is O2),
does anybody know standard password for this phone? i'd like to change CALL BARRING SETTINGS, i need CALL BARRING PASSWORD.
thanks.
as wm5 is not offical
i doubt it's a real o2 rom
and CALL BARRING sounds
very very much like something
put in the sim rather then on the
phone
Hi,
Since a few weeks back my Trinity always shows Unknown as the user id of the incoming call.
At the beginning I thought it was Rom related, since I've been messing around with Mary's and Axel's roms. But I went back to the official one with same result.
I must admit that I have dropped the Trinity a couple of times. So I was wondering if anybody knows if this functionality is sofware or hardware related (maybe I damaged sth when dropping it?!?!)
Or maybe is some registry setting?!?!?
Any thoughts greatly appreciated!!
Thanks,
Elsral
I had the same problem before though i didn't update any ROM. Try downloading your telco settings again. (Network Wizard).
caller id is a service of your provider so if you disable it once il will always be disabled, whatever rom or phone you use
you can reactivate it in the settings>phone>service
Hi,
thanks both for your input.
I went to settings/phone/callerid/ and set to show to everyone.
However, I think this is only for the reverse process, to show your number to the person you are calling.
However, I still don't know who is calling me. Any other Ideas?
thanks,
elsral
elsral said:
Hi,
Since a few weeks back my Trinity always shows Unknown as the user id of the incoming call.
At the beginning I thought it was Rom related, since I've been messing around with Mary's and Axel's roms. But I went back to the official one with same result.
I must admit that I have dropped the Trinity a couple of times. So I was wondering if anybody knows if this functionality is sofware or hardware related (maybe I damaged sth when dropping it?!?!)
Or maybe is some registry setting?!?!?
Any thoughts greatly appreciated!!
Thanks,
Elsral
Click to expand...
Click to collapse
Bump.
I've exactly the same problem since the beginning of january.
All the incoming voice calls are "unknown", no number is displayed.
But incoming SMS are ok, the sender number is correctly displayed.
I've reinstalled my network provider settings (Orange F), with no success.
Someone has a solution ?
Thanks.
try your sim card in another phone. i suspect your operator disabled it. you may want to give them a call.
ww2250 said:
try your sim card in another phone. i suspect your operator disabled it. you may want to give them a call.
Click to expand...
Click to collapse
You were right. It's same problem with my sim card in another phone.
I've called my network operator, he reset the parameters of my line, and it works now.
Thanks.
Hi I'm jayus from Indonesia. I have HTC Ozone Verizon. I have unlocked it and used it with my local CDMA and GSM operator. I have two problem about the phone.
1. When I'm in GSM mode, if i dial '081212345678' the call would not connect. However if i try dial complete number like '+6281212345678' the call would connect. But if I'm in CDMA mode I have no problem about this, I can make a call using direct number like 081212345678 and the call would succeed. I have turned the assisted dialing on and set the the reference country to indonesia, but the problem still exist.
2. When I'm in CDMA mode, everytime I try to send SMS the phone would automatically change the destination number from ex 08129500140 to 01108129500140. Looks like the phone always add prefix 011 to the real number. So I always failed to send SMS. But the problem didn't exist in GSM. In GSM mode I can send SMS successfully and the phone did not add prefix 011.
What's wrong with the phone? Need help please..!!
Hi,
This is interesting cause i have the same problem with my
Touch pro 2 from VERIZON.
I made a thread about it, follow it here:
http://forum.xda-developers.com/showthread.php?p=5854877
I was thinking this might be something in the verizon stock rom so if you flashed
to a rom that wasnt stock from Verizon you wouldnt have to deal with it.
I havent got this confirmed yet.
Keep me posted if you find something
I dont know about cdma i only use gsm.
I hade the exact same problem as you and I finally solved by disabling
assisted calling in registry settings
Hey everyone,
my Axon seems to hide my phone number by default when I call other people.
I know that the phone is responsible for this because:
1. others can see my number when I call them with my old phone
and
2. when I put *31# in front of a number to basically override the phones setting the person I'm calling will see that it's me.
I feel like there is no setting to change the caller ID option in my Axon. At least it's not where it normally is (Call Settings, Additional Settings).
Does anyone have a similar problem or even better, a solution?
I asked about this on ZTE`s forum and never received a reply.
Okay, that's interesting.
I wonder why no one in the Axon 7 section talks about this issue. There should be more people with the same problem.
This is generally a carrier setting problem not a phone problem.
For T- Mobile not sure about ATT.
*67DN Activate Calling Line Identification Restriction (CLIR) for outgoing call
*82DN Deactivate Activate Calling Line Identification Restriction (CLIR) for outgoing call
In this case I know that it is not a carrier problem because I've tested it.
It might be worth mentioning that I own the European model and that I live in Germany.
Same for me, Europen Version and I live in Germany. Provider is O2. Switched from my HTC M8 to the Axon 7, had no hidden caller ID whatsoever on the M8.
Kind of annoying and I can't find anything to switch it off.
Anyone else has the same problem?
rootkowa said:
Anyone else has the same problem?
Click to expand...
Click to collapse
I live in France and my provider is Free Mobile.
The caller ID works for me.
My Axon 7 is a 2017G model with B05 firmware.
I've got news:
After dialing the gsm code #31# the phone is no longer automatically hiding my number. The strange thing is that this code is supposed to do something completely different: hide the number for the next call.
This still works after restarting the phone but after updating the software (bo5 to b06) I had to dial the code again which means that this method is only a temporary fix and this is something the ZTE devs have to look into.
Same here in Spain
I suscribe all your comments ace.infinity.
I'm in Spain, my carrier is Oceans. I'm in last build and with code *31# my name appears, I have to use it in all calls to be visible.
No solution found by the moment.
Incorrect
ItsLasher said:
This is generally a carrier setting problem not a phone problem.
For T- Mobile not sure about ATT.
*67DN Activate Calling Line Identification Restriction (CLIR) for outgoing call
*82DN Deactivate Activate Calling Line Identification Restriction (CLIR) for outgoing call
Click to expand...
Click to collapse
It is the phone setting itself that is now hidden from thre user menu that is actually hiding the number!
I was able to modify my caller ID setting by opening the phone app > menu> setting > call setting> SIM 1 or 2> additional setting.