Hi
on my ipaq 914 button UP on jogdial stucks very often. Is there any chance to get disassembling manual for device? I want to remove keyboard and try to clean it
Related
I have dopod c 800 which is broke wjile install the WM 6 ,now the condition just the startup screen with :
- dopod logo
- ipl 1.09.001
- spl 1.09.001
-gsm 02.69.90
i'm trying to get into bootloader by pressing camera and stylus or camera+comm manager + Stylus , but the screen was goin back to the logo of dopod again.see the figure
i think after get into bootloader i can install the original rom first then install again the wm 6
some body help please
Try holding the Camera Button after Reset, until Bootloader Screen appears, this must work out !
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Thanks
papamopps said:
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Click to expand...
Click to collapse
Thanks it works but pls find the way to make the gsm work after ugrading to WM 6 , nice system ..but sad always searching signal for the handphone.
Thank you
I have made my worst error in my life i think... i was trying to update my rom.... but ...
First my HW6915 with a great hp logo wich says "hp invent, vG.39" and in the top something that says "serial" or "usb" when i plug it up.
I try to fix it with i know .
But now ....black ......with nothing
I have reading all the things you talked and having no idea .
i asked someones help..How can i do!
Do i have something to do ??? Has my ipaq chances ?...
PLEASE HELP ME !!!!
still in trouble with your 6915?
wikidorg said:
still in trouble with your 6915?
Click to expand...
Click to collapse
Yes ,it's still in trouble. what can i do.....
can you make a hard reset?? by pressing simultaneously the five buttons : power button, camera button from left side, green "send" button and red "end" button from keypad and the soft-reset button (using your stylus)... ? (i was tired first time i wrote the procedure, my mistake!)
or, perhaps, enter bootloader by pressing simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset (using your stylus)
if ok, you'll have that screen again, showing vG.39 on bottom, and "serial" or "usb" on top...
Helo !
You can try hard reset, bat not in the way wikidork was told you. You must press POWER button, GREEN dial button, RED stop button together and then pres RESET with stylus. If this wont work then try with bootloader mode like wikidork told you. When you are in bootloader mode try to upgrade with French ROM and then with ENGLISH one like i did. This must work.
Best regards,
Drahtman
NO use.
Always black
that means you accidentaly broke your hp's bootloader... unless you have some knowledge on dealing with JTAG-related operations, it seems useless to try other software miracles...best advice : sell the rest of your device or buy a similar hp with broken display from e-bay, in order to change the mainboard... or send the dead ipaq to some professional service...
regards
Pls Where is french rom?
i hope recuperate hw6915... pls help
i have hw6915 and now appears on screen SERIAL and vG.39. I tried write rom with ruu.exe and .... "code 203: UPDATE IS INCOMPATIBLE
This version of the Update Utility is not compatible with yor iPaq.. bla..bla.. bla
This Update: Model ID: hp iPAQ69(0,5)
Language: ALL
Your Device: ModelID: hp iPAQ hw6915
Language: WWE"
anybody can help me?
my email is [email protected]
Hi,
Here is the link of French rom:
http://forum.xda-developers.com/showthread.php?t=337975
Try with Orange one.
Best regards,
Drahtman
hw6915 german to spanish
Hi. Please I need your help because I don't now if my PDA is broken, I tried to change the language German to Spanish the realized steps have been the following. - hw6915_up_2_spanish_flasher
when the installation process finish (I'm not sure if I disconnects the PDA from the base before finish the process because now on the screen appears the following.
Serial + hp + vG.39 but change when I conect it to the computer to : USB + hp + vG.39
I don't now what is the next step to load spanish rom I have the archive but how I have to do it because when I conect the Hw6915to de computer to charge the rom after one minute appears error.Pls what I can do but the thing is that now the PDA is inoprative NO GERMAN - NO SPANISH.
please can you help me to repair or finish the process.Thank you very much in advance for your cooperation. and sorry for my bad english
[email protected]
HELP iPaq HW6965 FREEZ ON START UP only hp logo on screen and fone cant connect to pc and cant put it on boot mode , any advise please or how to realy put in boot mode ? thx in advance
Enter Bootloader mode !
To enter bootloader mode press simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset with your stylus, but you must put screen under the bright light or you wont see when your iPAQ will go to bootloader mode. Then you put USB cable from iPAQ to your PC and you will see if iPAQ detects USB craddle. Then you tray to update iPAQ with french ROM and this is it. Try this and report.
Best Regards,
Drahtman
before bootmode try to take out your miniSD and then try HR
power+send+end+SR
it is trky so may not work for the first time
so try till you make it right
good luck
drahtman said:
To enter bootloader mode press simultaneously the two front buttons (the left and right of the keyboards joystick) and the soft reset with your stylus, but you must put screen under the bright light or you wont see when your iPAQ will go to bootloader mode. Then you put USB cable from iPAQ to your PC and you will see if iPAQ detects USB craddle. Then you tray to update iPAQ with french ROM and this is it. Try this and report.
Best Regards,
Drahtman
Click to expand...
Click to collapse
phone cant go on boot mode only says done or somthing else and restart on hang screen hp but no boot mode sucsess , any advise plz ?
Hi.
I have an ipaq 6910.I tried to install wm6 on it, and it crashed. Now it won't even start! Can you give me step by step info on how to start it in bootloader.. then flash it, and maybe a link with the software required for this operation?! thank you very much
Can you go to the boot loader by holding power+center(the direction pad), then reset hole? if yes, reflash it.
terry_cheong said:
Can you go to the boot loader by holding power+center(the direction pad), then reset hole? if yes, reflash it.
Click to expand...
Click to collapse
frist try a hard reset : green + red + power buttons + stylus soft reset
if this don't works try : the tw soft butoons + powerbuttons + stylus reset
then reflash it
good luck!
Thanks
klaxhu said:
frist try a hard reset : green + red + power buttons + stylus soft reset
if this don't works try : the tw soft butoons + powerbuttons + stylus reset
then reflash it
good luck!
Click to expand...
Click to collapse
I found solutions at the end, and that is working fine.
read the forum first
of cource it didn't work you dumbhead, if you had read fist some topics in here before doing that stupid upgrade you would have saw that for the hp 6500 and 6900 series there is no windows mobile 6 !!! you flashed the wrong rom to your phone,if it still working in bootloader and sees the usb connection thern reflash to a wm5 rom version and ask something before you flash not after !!
Help I too have stupidly tried to upgrade to windows mobile 6.1 without checking
............
I tryed flesh my ROM from original HP WM5 to WM6.1 from miniSD image and it was failed. Now I have brick from RW6815. I try remove batery and keep two buttoms --, one time I saw logo HP but I didn't know what to do. So ater 5 minuts I reset it. Now I have new BL 1.0.5 on miniSD but I can't enter into mode with HP logo. Do I have only one attempt? Do I have any change to go reactivate it?
Idea: "removing battery pack for a few minutes.After that we must press the both '_' keys and put the battery pack (don`t unpress the keys) and wait.After few minutes you will see the HP logo" doen't work for second time.
many thanks for any idea.
Varan said:
I tryed flesh my ROM from original HP WM5 to WM6.1 from miniSD image and it was failed. Now I have brick from RW6815. I try remove batery and keep two buttoms --, one time I saw logo HP but I didn't know what to do. So ater 5 minuts I reset it. Now I have new BL 1.0.5 on miniSD but I can't enter into mode with HP logo. Do I have only one attempt? Do I have any change to go reactivate it?
Idea: "removing battery pack for a few minutes.After that we must press the both '_' keys and put the battery pack (don`t unpress the keys) and wait.After few minutes you will see the HP logo" doen't work for second time.
many thanks for any idea.
Click to expand...
Click to collapse
Hi,
Look here for the bootkeys....
Dirk
I finished in this step:
- Go to bootloader : Press both soft key (two "-" keys) and softreset (stylus), i'll apear HP bootloader sceen.
----------
nothing happend, it was worked only for the first time. Now I can press both soft key and softreset but no HP bootloader start
When I connect to the power baterry is changing (orange green) and after that green. Thats all behaviour what is works.