RW6815 brick - Sable

I tryed flesh my ROM from original HP WM5 to WM6.1 from miniSD image and it was failed. Now I have brick from RW6815. I try remove batery and keep two buttoms --, one time I saw logo HP but I didn't know what to do. So ater 5 minuts I reset it. Now I have new BL 1.0.5 on miniSD but I can't enter into mode with HP logo. Do I have only one attempt? Do I have any change to go reactivate it?
Idea: "removing battery pack for a few minutes.After that we must press the both '_' keys and put the battery pack (don`t unpress the keys) and wait.After few minutes you will see the HP logo" doen't work for second time.
many thanks for any idea.

Varan said:
I tryed flesh my ROM from original HP WM5 to WM6.1 from miniSD image and it was failed. Now I have brick from RW6815. I try remove batery and keep two buttoms --, one time I saw logo HP but I didn't know what to do. So ater 5 minuts I reset it. Now I have new BL 1.0.5 on miniSD but I can't enter into mode with HP logo. Do I have only one attempt? Do I have any change to go reactivate it?
Idea: "removing battery pack for a few minutes.After that we must press the both '_' keys and put the battery pack (don`t unpress the keys) and wait.After few minutes you will see the HP logo" doen't work for second time.
many thanks for any idea.
Click to expand...
Click to collapse
Hi,
Look here for the bootkeys....
Dirk

I finished in this step:
- Go to bootloader : Press both soft key (two "-" keys) and softreset (stylus), i'll apear HP bootloader sceen.
----------
nothing happend, it was worked only for the first time. Now I can press both soft key and softreset but no HP bootloader start
When I connect to the power baterry is changing (orange green) and after that green. Thats all behaviour what is works.

Related

Pls Help for bootloader of dopod c800 not worked aft trying install WM 6

I have dopod c 800 which is broke wjile install the WM 6 ,now the condition just the startup screen with :
- dopod logo
- ipl 1.09.001
- spl 1.09.001
-gsm 02.69.90
i'm trying to get into bootloader by pressing camera and stylus or camera+comm manager + Stylus , but the screen was goin back to the logo of dopod again.see the figure
i think after get into bootloader i can install the original rom first then install again the wm 6
some body help please
Try holding the Camera Button after Reset, until Bootloader Screen appears, this must work out !
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Thanks
papamopps said:
You have to hold both buttons (camera and commanager) until the bottscreen appears. only teh softreset button is pushed once.
DOn´t left the other bottons before bootscreen appears.
Good luck
Click to expand...
Click to collapse
Thanks it works but pls find the way to make the gsm work after ugrading to WM 6 , nice system ..but sad always searching signal for the handphone.
Thank you

mda vario

I have a big problem with my mda vario.
the begenning: !. i done a hardreset and before finishing a softreset.
now my ppc doesnt boot anymore. the hung up is by the screen of t-mobile.
Plese help me!
What can i do now, is my mda vario over?
No resets bring me forward
Touchscreen or any other buttons doesnt react and doesnt work anymore.
The only thing that i can do is to remove the battery
Stupid question, but why would you do a soft reset in the middle of a hard reset?
Anyway, probably your best bet would be to download the latest t-mobile rom, put your phone in bootloader mode and flash the rom again. This time, avoid doing a soft reset in the middle of it.
how do i install the rom in the ppc if it doesnt boot.
can you give me a todo list, please ?
how can i put my phone in bootloader mode
Press and hold the camera key and then press the on button. When multicolored bootloader screen comes up release the camera button and then you're ready to flash.

Stuck in Bootloader

Hello,
i tried to update my BA with wm6.
after flashing it stuck in bootloader(blue,green,red,white display) with the line "R 1.10.00" and nothing more...
even hard or softreset do nothing.
what can i do?
ok i even try the Stuck at startup method.
that's the output of Multiport TTY Version:
set 14 0
HTCST ÚÈÒHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>task 0
it always stuck in blue,green,red,white screen after run multiport tool. what can i do?
------------
i have this problem because of this flashing method:
i entered the grey screen (with serial/usb in first line). then i put my usb connection on and run the rom_update. after it is finished (succesfully) it stuck in the blue, green, red, yello screen! help please...
how did you hard reset?
hello,
i hold down the power-button and at same time put stylis in reset.
hard reset for both WM5 and WM6 is different from the one you're doing. here's the guide...
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
good luck!
ok thanks, i have tried this:
i do softreset. whenn the stripes came i push "records and "camera"(media player button because there is no camera)---> nothing happens. it stops with the line R 1.10.00 and the coloured stripes.
i dont knwo what to do.
the bootloader method is running. i hold power and record button while i softreset. but with color screen it wont work.
they is no camera button (it is media-player button) because there is no camera. its an german xda III (blue angel).
the next problem is i dont knwo what os is right now on it. befor flashing it was wm2003 and flashing says it was successfully. i dont know if its wm6 or wm2003!
ok now all is happen...
the xda says nothing. it dont go on, it dont work anymore. no lights when in cradle, nothing.
can i do anything?
1. Take the battery out, wait a moment, put it back, do not turn on. Put in the cradle and try to charge it. Use power connection (from power supply), disconnect USB from the computer for charging. Amber led should turn on.
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
jakubd said:
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
Click to expand...
Click to collapse
it was not unlocked befor i flashed with bootloader-method.
i charged the battery in cradle (withoud the blue-angel). the led first went orange, after a while turned green (fully loaded). put it back in BA an nothing happens. then put BA (with battery) in cradle and the led became red.
no action on devide, no feedback, nothing. it wont turn on but led is still working.!?
jakubd said:
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
Click to expand...
Click to collapse
ok i get it. in display is the "USB" & "v2.07". now i can flash. but my problem is the phone is not unlocked yet. what file can i flash now??
This message tells you are in bootloader mode. Now you can perform normal flash - I would propose you to use tested&working rom (WM2003?). If this works fine, try again to upgrade to WM5/WM6.
BTW: if you disconnect USB (take out BA from cradle) it should show Serial instead of USB.
ok big tanks to the forum. i finally get it. wm6 german on blue-angel!
Same thing here... but worst..
My 9090 is stuck at bootlader...
When i try to update, (i press the power, record and reset), it says:
SERIAL (or USB)
DOC VERSION IS ERROR!
v2.08
Any idea???
that's normal...
try to flash/update your BA in that screen.
the easy way to go into bootloader mode is to execute a file called Enter Bootloader.exe ..it comes with the rom u download..( well it came with xplodes )
Note:- you have to execute this file directly on your deive not on your desktop PC...and i have only tested this on WM 2003..maybe it will work with wm6 also
SilverSamurai said:
that's normal...
try to flash/update your BA in that screen.
Click to expand...
Click to collapse
I there...
I just updated to BA_TMNL_14200_119_11300_Ship, but only with Maupgrade, couldnt do it with baupgrade...
The problem is that i cant put extended rom, whem i try to upgrade is allways an error... and in the settings i dont have extended rom instaled...
Besides that the batery only last 1hour and the PDA is always freezing... i'm always doing resets...
any idea??
Sorry for my bad english by the way...

Help required WM6.1 for Typhoon/Feeler/Amadeus [1.5]

Hi Guys!
I have a Feeler. Flashed it with WM6.1 for Typhoon/Feeler/Amadeus [1.5]
It worked well for 2 - 3 weeks. Then the device hung. Now, i cannot access the device. When it reboots, it stops at the sceen showing "Mobile Operator" It does not want to hard reset......
Help?
Okay....
I got something happening. When i rebot, i pressed 1 clean Hive, now it booted back up.........
Wonder why this happened?
Any ideas guys?
pressing 1 on the startup screen is used to hardreset your phone... If you tried the old way (pressing the combination of key) will no longer work and you will freeze your phone..
So remember each time you press 1 on this screen you are doing a "hard reset"

[Q] pleezzzzz HELP ME... i need all of ur help... PLEEZZZZZZZ

i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
after you have fully charged your phone, try flashing it again...Happy New Year.
tnx.... but how cant flash it again... becuze its doesnt start to bootloader... i cant it power on.. plz help me... hw do i flash it????
you try to flash WM5 rom and then flash the rom. offline flash memory card.
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
try to Hard Reset your device , here the way to do that...
Perform a hard reset with the iPAQ. To perform a hard reset,
1. Press and hold the Answer/Send, Power, and End Call buttons.
2. While holding these buttons, use the stylus to lightly press the Reset button on the bottom (located at lower left base of the iPAQ), of the HP iPAQ until the device restarts.
3. When the HP iPAQ restarts, release all of the buttons, and then remove the stylus from the Reset button. The HP iPAQ restarts and powers on.
CAUTION: A Hard reset clears memory, deletes all data (such as owner information under Setup Wizard and AutoConfigurator) and restores the rw6818/rw6828 to its default factory settings. The action will erase all data that you have created and programs you have installed, but will keep all the preinstalled programs that were in the phone when your phone was first delivered to you. Be sure you have backed up all your data in a mini SD card or on your PC before performing a hard reset

Categories

Resources