I have a big problem with my mda vario.
the begenning: !. i done a hardreset and before finishing a softreset.
now my ppc doesnt boot anymore. the hung up is by the screen of t-mobile.
Plese help me!
What can i do now, is my mda vario over?
No resets bring me forward
Touchscreen or any other buttons doesnt react and doesnt work anymore.
The only thing that i can do is to remove the battery
Stupid question, but why would you do a soft reset in the middle of a hard reset?
Anyway, probably your best bet would be to download the latest t-mobile rom, put your phone in bootloader mode and flash the rom again. This time, avoid doing a soft reset in the middle of it.
how do i install the rom in the ppc if it doesnt boot.
can you give me a todo list, please ?
how can i put my phone in bootloader mode
Press and hold the camera key and then press the on button. When multicolored bootloader screen comes up release the camera button and then you're ready to flash.
Related
I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?
Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....
Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.
Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks
Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks
Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?
Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.
hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.
Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.
Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.
T-Mobile MDA USA weird, "fixies" dont work, stuck in "press send to restore"
Hi, sorry for my poor English is not my first language
I have a T-Mobile MDA USA and happened a weird thing, my phone works properly, was CID unloked and sim unloked with TNT_5.0_Wizard_TouchFLO ROM but 3 days ago I put the USB (PC)to charge the battery, lately when I back to pickup my phone I see in the screen of the phone open and close or put an quit windows explorer(mobil) repetitively, i try to close manually tapping in the "X" but explorer continues opening, then I see in the bar where you put the web address the number "3" and "8" was typing continuously, like when you hold pressing the buttons, but nothing was pressing or making pressure to do that, since I cant close the explorer with the "X" I turn off the phone, when I turn on instead to load normally, appears the Align Screen and for some reason will not recognize the Screen Tapping to align the screen, so, I turn off/on again, but in this time shows a black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, it is stuck in there since, before to put this tread I have read this forum and still I am lost, because i do a Soft Reset or Hard Reset #1,#2,#3, I enter into a bootloader mode to re-flash the ROM with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ... IPL/SPL 1.01 and when finish to flash, its suppose the phone restart and windows loading but instead that I get again the same black screen with "Press Send to Restore Factory Defaults, Other Key to Quit" in withe letters, ok, maybe with other recently ROM, then I enter into a bootloader mode to re-flash the ROM... AGAIN... but now with ruu_prodigy_226102_22610105_022511_tmous_wwe_ship... IPL/SPL 2.26 ... and AGAIN I get the same black screen with "Press Send to Restore"... I try to press send key always, but nothing happens, is still stuck there always, I could not get past that, I would really appreciate any help. Thank you so much.
I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.
l33tphreak said:
I hate to ask this, at the risk of sounding too obvious, but are you sure that it was CID unlocked properly? I have a Cingular 8125 with IPL/SPL 2.25 and I know it was a hell of an effort to get it CID unlocked, five or six tries before it worked properly and I was able to flash successfully.
Click to expand...
Click to collapse
yes was CID unlocked properly, I do it with lokiwiz02b like 3 moths ago and I use Wizard Service Tool to see was really unlocked, I could flash any ROM since was unlocked I could use crosbow,faria, Molski even TNT.20273_Professional ROM's but I prefer use TNT_5.0_Wizard_TouchFLO because I feel my phone works more stable and speedy... searching in treads I see Im not the only one with the same problem (stuck in a black screen with the legend " Press Send to restore factory default, other keys to quit" in white letters) but in that treads no one get answer how fix this problem or how get out of the black screen.
like I say before I could put my phone in bootloader mode and re.flash the ROM wherever I want to try running ROMUpdateUtility and always I reach 100% then, when its suppose the phone restart and you will see the windows logo or T-mobile, don't happen that, instead I see the famous black screen with white legend, so the legend says me "press send"... I press send, or any key and nothing happens... I read in other treads when you press send the phone formating but this is not the case, just don't do nothing,.... realy I need some help here
thanks
Hey!
I have the same problem as described above. I've been using CR96 Touch HD WM 6.1 with soft SPL unlock for couple of months with no problems until tonight when I noticed that my phone is hanged. I did a soft reset, but the phone gets stucked at "press send to restore factory default, other keys to quit" screen. At that none of the buttons work, soft resetting just puts it back to this screen, the same goes for taking the battery out. There have been no software or registry changes within weeks - just using basic phone functions. Is there any way how to fix this or what could be the problem?
Thanks in advance
Hi everybody,
on my Trinity hard reset doesn't work anymore. After for example flashing with a new rom bootloader just blinking. OS is booting normally but hard buttons doesn't work only the "joypad" in the middle. For hardreset i have to press Send button to accept hard reset when i remeber well. But nothing happend when pressing the button. In fact that the device wants a hardreset, softreset is the same problem. I have to replace battery to access OS and boot device. Has anybody a solution? Or is there a progam for WM which can make a hardresend?
€dit:
Is it possible that something is wrong with the bootloader?
thanks and best
Robbat
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
after you have fully charged your phone, try flashing it again...Happy New Year.
tnx.... but how cant flash it again... becuze its doesnt start to bootloader... i cant it power on.. plz help me... hw do i flash it????
you try to flash WM5 rom and then flash the rom. offline flash memory card.
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
try to Hard Reset your device , here the way to do that...
Perform a hard reset with the iPAQ. To perform a hard reset,
1. Press and hold the Answer/Send, Power, and End Call buttons.
2. While holding these buttons, use the stylus to lightly press the Reset button on the bottom (located at lower left base of the iPAQ), of the HP iPAQ until the device restarts.
3. When the HP iPAQ restarts, release all of the buttons, and then remove the stylus from the Reset button. The HP iPAQ restarts and powers on.
CAUTION: A Hard reset clears memory, deletes all data (such as owner information under Setup Wizard and AutoConfigurator) and restores the rw6818/rw6828 to its default factory settings. The action will erase all data that you have created and programs you have installed, but will keep all the preinstalled programs that were in the phone when your phone was first delivered to you. Be sure you have backed up all your data in a mini SD card or on your PC before performing a hard reset