I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?
Related
Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....
Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.
Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks
Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks
Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?
Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.
hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.
Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.
Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.
Hello. First all sorry for my english.
Since a few days the buttons of my pda are crazy and don't work properly.
For example: The power button don't switch off the pda, but if I press and hold the button for a few seconds, switch off the ligth of the screen. This mean that the button isn´t broken, is it??? With the cam and record button it´s the same. If I press those buttons on windows 6 it works perfectly but i want to hard reset my pda and when reset and press whe i have to change "Clean Registry Hive " and "Format Storage" I can't change these options and cant make hard reset.
Then that is the question:
How can i make hard reset?? is there an alternative metod???? At Qtek S200 there is an application that clean the memory. It Exists for my blueangel??'
There is any application than do it???
Thanks. I´m waiting for answers.
u can use psshutXP it can do a hardreset with confirmation by holding the upper right corner of the application.
Hello.
Thanks for your answer.
I have tested your option, but it seems that the hard reset doesn´t work in wm6. It changes time and date, but don't clean memory, because i have the same programs than before.
I need another metod.
Thanks.
here u are..
just reset first your device, than after you see the stripped screen, press the record and camera button quickly before the the version appears (radio,etc).. then you will see the three options..
enable kitl should be no
clean registry hive should be yes
format storage should be yes
to choose just use the camera and record to change the options...
good luck
cheers
adri..
Hello evoluzionne.
I know that way to do hard reset, but my problem is that i can´t change the options:
enable kitl should be no
clean registry hive should be yes
format storage should be yes
In Windows Mobile 5 or 6 the camera and record buttons works properly, but when I reset the device and press the record and camera button quickly before the the version appears (radio,etc).. i can´t change the optios. It´s seems like the buttons don´t work. But i know that the buttons works, but the buttons don´t change the options. It´s very stranger.
In the power button is seemed. I can switch on the device, i can switch on/off the screen if I press and hold the button but i Can´t switch off the device. It´s incredible. My buttons are crazy. So i want to do downgraded to WM2003 ( so I need to do hard reset).
Do you know why are my buttons crazy????
Thank for your answer, and sorry for my english
Ciao
Hi,
Just wondering if you resolved the issue. I am having a similar problem on pda2k upgrading from wm5 to wm6. Buttons work except during boot menu so i cannot change options.
Appreciate your help.
MC
melilleny said:
Hello evoluzionne.
I know that way to do hard reset, but my problem is that i can´t change the options:
enable kitl should be no
clean registry hive should be yes
format storage should be yes
In Windows Mobile 5 or 6 the camera and record buttons works properly, but when I reset the device and press the record and camera button quickly before the the version appears (radio,etc).. i can´t change the optios. It´s seems like the buttons don´t work. But i know that the buttons works, but the buttons don´t change the options. It´s very stranger.
In the power button is seemed. I can switch on the device, i can switch on/off the screen if I press and hold the button but i Can´t switch off the device. It´s incredible. My buttons are crazy. So i want to do downgraded to WM2003 ( so I need to do hard reset).
Do you know why are my buttons crazy????
Thank for your answer, and sorry for my english
Ciao
Click to expand...
Click to collapse
Another BA with the same problem
melilleny said:
Hello. First all sorry for my english.
Since a few days the buttons of my pda are crazy and don't work properly.
For example: The power button don't switch off the pda, but if I press and hold the button for a few seconds, switch off the ligth of the screen. This mean that the button isn´t broken, is it??? With the cam and record button it´s the same. If I press those buttons on windows 6 it works perfectly but i want to hard reset my pda and when reset and press whe i have to change "Clean Registry Hive " and "Format Storage" I can't change these options and cant make hard reset.
Click to expand...
Click to collapse
Hi,
I have an exact problem as you. I've followed any info about hard reset, I've red wiki 100times, searching using Google but perform hard reset or enter to bootloader mode on my BA is IMPOSSIBLE!
In November I've upgraded to WM6, ROM from pdaviet, OS 5.2.2000 (Build 20000.1.0.0.PV.HAT)
MDA is working without problems, I can use phone, wifi, camera, record, BT, ActiveSync 4.5.
Right now I want to upgrade to new ROM from pdaviet but I stuck with a step: enter to bootloader mode
I've tried psShupXP software, which is capable do a hard reset. Still no luck, after software hard reset my BA comes on with all files installed...
Unfortunatelly mtty doens't works too, I can't see any WCEUSBSH001 port...
I'm not alone, but the bad news is that I don't find any solution
Thanks for any hint
R.V.
I have the same problem as you do, except I can enter BootLoader and Hardreser, but I can't turn off my device with power button, and if I hold it for long it shuts the backlight.
If anyone had any sucess solving this please share how...
Thank you.
evoluzionne said:
just reset first your device, than after you see the stripped screen, press the record and camera button quickly before the the version appears (radio,etc).. then you will see the three options..
enable kitl should be no
clean registry hive should be yes
format storage should be yes
to choose just use the camera and record to change the options...
good luck
cheers
adri..
Click to expand...
Click to collapse
I am following the same exact steps...flashed rom for the 5th time...hard reset is not working. The problem...'Mail' button (the hardware key) does not respond. I can change the options from No to Yes. But after pressing the 'mail' button nothing happens. Please let me know if there is another way to clear the registry hives and format the storage!!!
have you guys tried the MTTY alternative? i think it's somewhere here in the forum.
I am having the problem described in here.
By holding the record & media button, it *does* go to the hard reset menu, so obviously the record and wm buttons do work (ie is not a physical problem with the buttons), since these buttons do get it to the menu, it just does not allow any changes to the options (KITL, format storage, format registry hive)...
It is maddening, because I am stuck with the oldish pdaviet WM6 rom that crashes for me all the time and I want to try the newer 6.1 ROMs but can't hard reset and have seriously considered finding another used BA on ebay to start fresh it is driving me so nuts.....
I am about to search for the MTTY method described by samurai above... assuming I locate and can do it, I'll post results....
what do you mean "it just does not allow any changes to the options"? do you mean it wont let you navigate through each options? or do you mean it wont let you change from yes to no or no to yes?
any changes to the options are executed only after you have pushed the "mail" button
SilverSamurai said:
have you guys tried the MTTY alternative? i think it's somewhere here in the forum.
Click to expand...
Click to collapse
Catch:
http://forum.xda-developers.com/showthread.php?t=378640&highlight=MTTY
tried it myself - works great!
Bird
Hello,
I just uninstalled the Arabic support package (Pocket Arabizer Suite v2). Afterwards, I am not able to use my wing to make calls. I even tried to search for network and couldn't find any. I was thinking if I reinstall the Arabic package might help. Unfortunately, ActiveSync is not working no more as well. Also, I tried hard reset (by holding the 2 soft keys along with soft rest) but it wont reset.
Anyone got a clue ?
When you hard reset did you keep holding down the softkeys after you pressed the soft rest button? When done correctly a prompt to soft reset should come up after about 5 seconds
yes, I did
no one got a clue?
Go into bootloader mode and run the TMO RUU.
I was tryin to avoid that. But, I just done it
Thanks
Hi guys, I just took over my dad's Dopod that was running under Windows Mobile 5 today.
During which, I installed:
PCCPIMBACKUP (and did a back up)
FIXUNREADCOUNT.exe and ran it.
After that, I resetted the device manually by holding down the power off switch and now my device won't start up again. IT keeps going to the "Dopod Screen" where is later restarts and attempts o switch on again.
IPL 1.00
SPL 1.00.00000
GSM 01.13.20
OS 1.0.13.21
I have not installed any other software except for these and I have attempted to hard reset twice with no avail.
Any help will be greatly appreciated.
are you sure u hard resetted the correct way?
put device on standby, press comm manager & camera button & poke your stylus in the reset hole.
should be hard reset...
wanwarlock said:
are you sure u hard resetted the correct way?
put device on standby, press comm manager & camera button & poke your stylus in the reset hole.
should be hard reset...
Click to expand...
Click to collapse
Yeap, did that. I hard reseted it a few times, tossed it about (literarily) and the just left it alone for the night. The next morning it switched on and hasn't been giving me much issues. Though I just found out the loudspeakers are busted. ):
Did you Check your baterry?
Hello pal...
Today i just hard reset my dopod 818 pro via setting and clear storage.. its done nicely.. until i install ezinput keyboard and after soft reset my device is unbootable...
i try to hard reset my device (press camera and comm manager and poke reset button) but just colurful screen appears (red,green, blue) according to tutorial, the send command will appear... please help me..
I desperately need an alternative way to hard reset my hd2. Holding the up down button and shortly pressing the on/off button just switches the phone on. No reset. btw I cant start up normally so the software approach doesn't wort either.
Peter65nl said:
I desperately need an alternative way to hard reset my hd2. Holding the up down button and shortly pressing the on/off button just switches the phone on. No reset. btw I cant start up normally so the software approach doesn't wort either.
Click to expand...
Click to collapse
Use the reset button on back whilst holding up/down buttons
a few people have commented on the difficulty of getting both up and down pressed correctly.
I find I get a much better press with the battery cover off, and I press one first, then the second.that way you can feel them connect individually.
Why don't you guys use the build in software to hard re-set the devise.
1] Press Star Icon
2] Press Setting Icon
3] Press System Icon
4] Press Clear Storage Icon
That should start a hard re-set on device and re-store everything back to original configuration.
maniep said:
Why don't you guys use the build in software to hard re-set the devise.
1] Press Star Icon
2] Press Setting Icon
3] Press System Icon
4] Press Clear Storage Icon
That should start a hard re-set on device and re-store everything back to original configuration.
Click to expand...
Click to collapse
why don't you read the opening first again?
the dude can't use the software approach because his windows won't start, remember?
what about using task 29 or the reflash original splash screen while its doing its thing you can use both hands to hold the vol buttons, other than anything else suggested i dont thinj there us another way to hard reset other than reinstalling your rom maybe fix the software wipe storage app.
That works!
11calcal said:
Use the reset button on back whilst holding up/down buttons
Click to expand...
Click to collapse
Thanks, finally got the thing going again.
I have the same exact problem. None of these methods are working for me. Is there anthing else I can do?
Same for me. Locked out of the phone completely. When it boots it only gets as far as the O2 start up screen and doesn't get any further. Hard and soft reset do nothing. Have tried all suggested here already.
When I get to the screen where I'm prompted to press Volume up to restore, it goes straight to 'restore completed' in a fraction of a second, then back to the start up screen when I press Volume up again.
Need help as I now have an HTC paperweight and no phone!
sonicuk said:
Same for me. Locked out of the phone completely. When it boots it only gets as far as the O2 start up screen and doesn't get any further. Hard and soft reset do nothing. Have tried all suggested here already.
When I get to the screen where I'm prompted to press Volume up to restore, it goes straight to 'restore completed' in a fraction of a second, then back to the start up screen when I press Volume up again.
Need help as I now have an HTC paperweight and no phone!
Click to expand...
Click to collapse
Been using magldr? Cos hard resetting with magldr installed just affects magldr, hence a very short reset time that does nothing.
samsamuel said:
Been using magldr? Cos hard resetting with magldr installed just affects magldr, hence a very short reset time that does nothing.
Click to expand...
Click to collapse
No, I don't even know what that is. I'm not very technical and all I had installed was Cookie's Home Tab Editor.
I have the same problem.
My HTC is blocked ( the WM "forgot" the password that I set - a common problem ), so I have to do a Hard Reset that doesn't start.
I can't reflash or do anything else ( as told here ) without instaling HSPL first. As this can only be installed by the Active Sync, and Active Sync doesn't connect to blocked phones, I can't do anything else...
Is there a way to do anything else with only a new ROM in the sd card ? Or I REALLY have to install HSPL first ?
Thanks,
Leo
leodino said:
Is there a way to do anything else with only a new ROM in the sd card ? Or I REALLY have to install HSPL first ?
Click to expand...
Click to collapse
It is possible to be stitched from a SD-card without reinsertion HSPL. It is desirable to stitch official ROM
It is desirable SD-card to format a feather an insertion.