Dopod 818 Pro Problem - JAMin, XDA Neo, S200 General

Hi guys, I just took over my dad's Dopod that was running under Windows Mobile 5 today.
During which, I installed:
PCCPIMBACKUP (and did a back up)
FIXUNREADCOUNT.exe and ran it.
After that, I resetted the device manually by holding down the power off switch and now my device won't start up again. IT keeps going to the "Dopod Screen" where is later restarts and attempts o switch on again.
IPL 1.00
SPL 1.00.00000
GSM 01.13.20
OS 1.0.13.21
I have not installed any other software except for these and I have attempted to hard reset twice with no avail.
Any help will be greatly appreciated.

are you sure u hard resetted the correct way?
put device on standby, press comm manager & camera button & poke your stylus in the reset hole.
should be hard reset...

wanwarlock said:
are you sure u hard resetted the correct way?
put device on standby, press comm manager & camera button & poke your stylus in the reset hole.
should be hard reset...
Click to expand...
Click to collapse
Yeap, did that. I hard reseted it a few times, tossed it about (literarily) and the just left it alone for the night. The next morning it switched on and hasn't been giving me much issues. Though I just found out the loudspeakers are busted. ):

Did you Check your baterry?

Hello pal...
Today i just hard reset my dopod 818 pro via setting and clear storage.. its done nicely.. until i install ezinput keyboard and after soft reset my device is unbootable...
i try to hard reset my device (press camera and comm manager and poke reset button) but just colurful screen appears (red,green, blue) according to tutorial, the send command will appear... please help me..

Related

White Screen only

I just installed this program, used default settings, apllied, My 8125 soft reset.
Now I cannot see anthing past the initial screen that lists IPL and SPL version.
Just a plain white screen, Active sync wont work, no buttons work. Please help !!!!!!!!!!
If you're stuck I think the only next step would be a hard reset which is going to drop it back to the base factory build so you'll lose anything you've installed etc.
How do I hard reset 8125, with buttons only (key / button combination) OS does not boot or visible.
press the "connetions" button (on the left hand side of the unit next to volume up/down) with the "voice" button (right hand side of the unit opposite the connections button) and then use the stylus to do the normal soft reset and it should hard reset back to factory settings - it's described in the manual
Tried hard reset several times, no luck.
All I did was installed registry wizard from here
http://forum.xda-developers.com/viewtopic.php?t=39725&highlight=registrywizard
and now I can't get it to do anything, anymore suggestions ?, your help is really appriciated, I have only had the phone to 2 days and its dead already
try holding the same two buttons and then hitting the power button instead of the reset thingy... this method was easier for me... If this dosen't work you will have to enter bootloader mode and reflash the rom.
For the detailed reset procedures try here
By the way, did you use that program to change the default input method?? I use it all the time and the only time it gave me the whitescreen is when I tried to change the default input...Oops. I believe that you should be able to use that program safely, just leave the default input alone... Hope this helps.
Thanks for info, I did manage to reload the ROM. and Yes I did change the default input method, that might have done it. Thanks all, for your Help.
raheelb did you have the warning that the proggie cannot recognize the AKU version?
I had had such a warning, unfortunately bypassed it and had the same issue (white screen) - any one knows why the RegistryWizard cannot recognize AKU version? I have the original Qtek 2.17 ROM installed... :?

my k-jam hangs

Hi,
Recently my pda(k-jam) fell from my pocket and it hanged. I did a soft reset but I get this error message "Press Send to restore factory defaults, Other keys to quit"
I tried all keys but in vain. I then did a hard reset by pressing the comm and the voice dial. (did a reset with my stylus). I still get the above error message.
Does anyone have any suggestion or idea how to reset my pda?
Thanks alot.....
Y dnt u flash it with a new Rom look around the forum for the new MOSKI ROM.
Thanks
Thank you for your suggestion, I will think of upgrading to molski.
But will it upgrade ? As a hard reset also doesnt seem to work and how do I get to reach the ROM if I am not able to see the other things?
Thanks
Please help...
Hi ,
I am a newbie and so would seek alot of help. Thanks in advance...
Couple of days back my pda fell and now after soft or hard reset the screen still shows this "press send to restore to factory defaults, other keys to quit"
I would like to upgrade to molski but they say I might have to downgrade my rom but I must first unlock the device. There are g3 or g4 device..how do I know what device my k-jam is...g3 or g4? How do I follow up or know?
Could anybody give me the link or solve my problem? As my k-jam just wont pass that screen..I tried looking into various topics but couldnt go about the first step I should be taking...
Please help!
Thanks
Hi,
Please help..after hard reset, it still does not happen to load into the factory defaults... I cant flash my ROM or anything ...as it wont progress further than that screen ... "Press Send to load factory defaults, or quit"
Anyone have any suggestion?
Hold down the camera button while resetting it. If you can get it to the bootloader (three color screen), you might be able to flash it with something and possibly rescue it. It does, however, sound like you might be screwed. Things break when you drop them, including plastic phones.
hi
Thanks but if I have to do a hard reset, I would already be holding the comm manager and the voice dial with the stylus to reset. Do I hold all the 3 buttons together while hard resetting ?
I have tried all the buttons after doing the hard reset but just doesnt get to the other screen.
Thanks for your help.
Hold down the camera button, Power Button and Pin in the hole. First relese the hole, then release the power button and keep holding the Camera button dis will bring the Tri-colour screen. There'll be some info. like IPL n SPL der
If IPL n SPL are like:
IPL 2.xx.xxxx or 1.xx.xxxx
SPL 2.xx.xxx or 1.xx.xxxx then ur device is G4.
if its like:
IPL 2.xx or 1.xx
SPL 2.xx or 1.xx then ur device is G3
if its G4 you need to CID Unlock that before upgrading it.
All the LUCK. Go Ahead.
Hi
Thanks,
I tried your steps but it still wouldnt work. But somehow I did the switch below the comm button and it showed me the screen to the somethign HTC innovation or like that.
I think I had to tinker with the switch below the button to get the screen working.Thanks for your help.

Please Help me Qtek s200

I have a qtek S200:
IPL 2.09
SPL 2.09.0000
GSM 02.07.20
OS 2.13.9.26
I have a problem, y qtek starts and goes until the "windows Mobile" Screen and then it stop.....and it stays in that screen for ever.........please help me out, i tried to hard reset and it doesn´t work what should i do?
Help me please!
What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.
See the wiki:
http://wiki.xda-developers.com/index.php?pagename=Flash_From_Bootloader
You have a G3 device, so make sure if you use a RUU, you use a G3 specific one.
levenum said:
What was the last thing you did before it stopped working?
Did you install something?
Are you sure you preformed hard reset? You must hold power + camera + comm manager buttons (all on the sides) then press and release the reset hole (at the bottom).
Then you will see a question asking you to confirm hard reset. If I remember correctly you need to press 'send' (the green phone button) to preform hard reset.
Please be sure to read the instruction on he screen.
Click to expand...
Click to collapse
thanks man it works, thank u a lot

Wing Problem

Hello,
I just uninstalled the Arabic support package (Pocket Arabizer Suite v2). Afterwards, I am not able to use my wing to make calls. I even tried to search for network and couldn't find any. I was thinking if I reinstall the Arabic package might help. Unfortunately, ActiveSync is not working no more as well. Also, I tried hard reset (by holding the 2 soft keys along with soft rest) but it wont reset.
Anyone got a clue ?
When you hard reset did you keep holding down the softkeys after you pressed the soft rest button? When done correctly a prompt to soft reset should come up after about 5 seconds
yes, I did
no one got a clue?
Go into bootloader mode and run the TMO RUU.
I was tryin to avoid that. But, I just done it
Thanks

Dopod 818pro | Cant Hard Reset

Hello pal...
Today i just hard reset my dopod 818 pro via setting and clear storage.. its done nicely.. until i install ezinput keyboard and after soft reset my device is unbootable...
i try to hard reset my device (press camera and comm manager and poke reset button) but just colurful screen appears (red,green, blue) according to tutorial, the send command will appear... please help me..
now got a new probs... camera button is not function..how do i hard reset my dopod..
use hardreset program
Same problem
mikagami29 said:
Hello pal...
Today i just hard reset my dopod 818 pro via setting and clear storage.. its done nicely.. until i install ezinput keyboard and after soft reset my device is unbootable...
i try to hard reset my device (press camera and comm manager and poke reset button) but just colurful screen appears (red,green, blue) according to tutorial, the send command will appear... please help me..
Click to expand...
Click to collapse
I have same problem, i try hardreset my Dopod 818 Pro than my Dopod 818 Pro cant power on, hard reset, softreset? give me no response, i try use jtag but, i dont know how to jtag for my Dopod 818 Pro, if you have solution please PM me. Thanks.

Categories

Resources