Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

My SVP M600 phone got stuck at Starting screen

Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.

did you try a hard reset ?

Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.

Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.

I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.

Can any one help me in this regard please.

I am having the same problem, but my phone is not sim-locked.

I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated

Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.

ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!

Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.

yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck

Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.

mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks

(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452

hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin

Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.

collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)

Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.

just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...

[SOLVED] Connection Error [262]. Stuck in bootloader (tri color) mode.

I'm new in these forums as well I'm new with flashing ROMs so obviously I messed up flash process and my device stuck in bootloader (tri-color) mode. This post I address to those unfortunate like me .
# Symptoms #
- ROM flash started and stopped at 17%. After recovery flash process stucks at 0% and pops Connection Error 262. Device is stuck in bootloader mode not possible to flash anything, hard reset does not help, flash from SD card does not help either.
# Possible cause for that #
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
2. Connection between ActiveSync and device was not established when flashing ROM file.
Before to go any further please take your time and read Polaris Wiki to get familiar with glossary and acronyms used here.
PROCEED ONLY if flashing original ROM does not help, hard reset does not help and flash from SD card does not work.
# Solution #
1. Download MTTY software.
2. Kill ActiveSync (Press Ctrl-Alt-Del and stop rapimgr.exe and wcescomm.exe processes).
3. Plug Polaris into usb port (Plug directly not through hubs).
4. Start MTTY after chose USB from PORT dropdown list (if it is not listed there then ActiveSync processes were not stopped).
5. in window type: set 16 0 (enter cmd mode)
6. after type: task 8 (this will format phone)
7. after type: task 0 (this will restart phone. Not always necessary)
8. soft reset
This procedure can damage your phone. Use it as last resort.
Official source in french here.
Now before flashing any ROMs read carefully how to flash (not install!) Hard SPL.
# P.S. about install and flash termins #
This error with flashing happened to my due misunderstanding between notions of installing something on your device and flashing. In my opinion those are completely two different things. As for first I understand of running some cab or exe directly on device. So problem comes when people sees install Hard SPL en device as they try to find some cabs or exes to install directly on device or they just copy all files to device. To make things clear Hard SPL "installation" actually is ROM flash process which must be done with maximum caution, but those who did not read Wiki won't understand it.
Cheers, whitealien

BiG THX @ Whitealien.
works to 100% on my Touch Cruise.
I flashed under Vista Ultimate...
# Solution # ... addition from me for Vista users!
....
2. Start Windows Mobile Device Center and Deaktivate USB Connection and then start Task manager end kill
Process wmdc.exe.
Rest of whitealien. and have fun!

Thank you!!!!
I had given up on this, and was sure my only option was a warranty repair :O

always welcome

Thanks, you've saved my Polaris.
Mine didn't want to react anymore to the soft reset, so I replaced your instruction 8 with:
Cmd>boot
and that did the trick.

whitealien said:
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
Cheers, whitealien
Click to expand...
Click to collapse
I had exactly the same problem, for whatever reason went back to original SPL before HARD SPL.
I solved my issue by using back the original original HTC RUU_signed.nbh and flash it using the CustomRUU.
Thereafter, repeat the entire HARD SPL and flash the home cooked ROM.
Cheers.

For unbricking your HTC Polaris, you can try also a hard-reset (if it is related to a software error):
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html

Thank you very much
you really helped
thank you again

mrfone2003 said:
Thank you very much
you really helped
thank you again
Click to expand...
Click to collapse
you are welcome.
Seems people are still falling for this error.

I'm has this error.
Solution (with SPL-2.20):
- kill ActiveSync (process, not uninstall)
- cable to USB on motherboard
- hard reset on phone
- connect to cable
- flash OFFICIAL rom
Two time I revive my Polaris.

help me please
hi.I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help

thanks for the support
Thanks dudes for the great help you gave to recover my htc dual from bootloader screen. I am very happy to have my phone back. Thanks for everybody for the help they have provided generously. I appreciate alot. infact thousands times.

I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.

aaront1988 said:
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
Click to expand...
Click to collapse
Did you follow all steps from 1st post?
Did you kill all running ActiveSync processes?

I did indeed, i'm on vista so didnt have those particular processes going but followed the step from Aeroman and it still doesn't want to play. Any ideas?

managed to find a working XP machine and it worked a treat. Thank you so much.

thanks,this solved my pb

please help
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((

wesram said:
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
Click to expand...
Click to collapse
What did you do to get there?

whitealien said:
What did you do to get there?
Click to expand...
Click to collapse
hey, im sorry for the late reply. it didnt notify me and now after posting several times asking for help in many threads by accident i bumped into this thread again to see that u answered and thank you so much.
now, what i did? this is the wierd thing, i didnt do anything, i went and back to see my phone stuck in bootload .... after this i tried almost everything i can find. from ur solution to flashing original rom to hrd spl to .........
now all gave an error except the original rom (polaris.1.28.415.2), it did went to 100% and device restarted to take me to my nightmare .... another bootloader screen am i suppose to search for polaris 1.28.0000?
i still have now the same writing shown.
please help me with this, its a nightmare .... is it totaly dead???
i managed to catch what it is saying b4 bootload screen (only when SD card is in place) it says no image file was found!!! in a very fast way and go to bootloader. in case the sd is not in place nothing happens and it goes straight to the bootloader

T-Mobile Ameo / Athena - Stuck in bootloader, won't connect to ActiveSync

I have got hold of a T-Mobile Ameo that's gone wrong whilst upgrading/unlocking, I believe they were using the Olipro way (which I've successfully done fine myself in the past) and it's now stuck in the multi colour bootloader screen which displays:
ATHE100
IPL-v2.02
ATHE100
SPL-v1.10.RP00
And although it shows USB when plugging it in to a computer it won't connect to ActiveSync so I can't get to the stage where I can re-flash it.
I have tried the hard reset by holding down the volume and pressing the reset hole, and I get to the prompt:
Press ACTION to restore factory default
Press Camera Key to exit
I then press the little nipple button down and it displays:
Restore default complete
Press Power Key to boot
Press CommManager Key to format micro drive
I press the Power Key and I'm back in the multi colour boot loader back where I started, and I canot connect to ActiveSync to reflash.
Any help to turn this paper weight back into a useful device would be appreciated...

exactly the same problem here.
any guru with a solution ?

seckt0r said:
exactly the same problem here.
any guru with a solution ?
Click to expand...
Click to collapse
Hi seckt0r,
have you tried reflashing the original rom for your device while connected to your computer in bootloader? ftp://ftp.xda-developers.com/Athena/Shipped_Complete_Updates/
another idea would be to try sd card flashing,(see the wiki) but you would need to extract an image from the flash utility.
One thing to note is you couldn't flash any of the newer roms as you are probably not unlocked

lakeman,
Thanks for the tips and sorry for the late reply.
I did figured out how to make it work again, and played a lot with the device
Already delivered back to the 'client'...

Active Sync issue is solved !!!
Active Sync 4.5 had changed the way it connects from USB Serial Sync Mode to RNDIS Sync Mode. So it can cause problems in connecting with PPC. Try install on your PPC the "ActiveSyncMode.sa.CAB" that you can easily find on Google & run it. Hope this might help.

same problem here i tried to upgrade with orignal rom tmobile uk but its show invalid vensor what can i do plz help thnx

got your msg ahmerp but I don't use MSN
have you tried some of the other shipped roms
if that fils you could try cmone s mtty solution to rswrite the vendor id

seckt0r said:
lakeman,
Thanks for the tips and sorry for the late reply.
I did figured out how to make it work again, and played a lot with the device
Already delivered back to the 'client'...
Click to expand...
Click to collapse
Please help me to sort out my ameo problem some one flashed with with wrong rom now phone shows only volume icons and whenever i try to flash with tuk roms it always give me error invalid model id e.g

Check post 33 on this thread http://forum.xda-developers.com/showthread.php?t=387454&page=4. You MUST use Windows XP with SP2 optionaly SP3 for this to work. If you need mac file for SPL1.2 send me email.

ameo stuck on bootloader after trying to unlock with athena unlocker
my tmobile uk was on rom 1.12. i tried to unlock and it went faulty on step 1. now it boots only in bootloader mode tri colour screen.
any tmobile rom gives invalid vender id error 294.
anyone can provide me with the original 1.12 tmobile uk wm5 rom?? also anyone cna help me online to change vender id using rswrite or pdocwrite.
Ayyub

hafizayyub said:
my tmobile uk was on rom 1.12. i tried to unlock and it went faulty on step 1. now it boots only in bootloader mode tri colour screen.
any tmobile rom gives invalid vender id error 294.
anyone can provide me with the original 1.12 tmobile uk wm5 rom?? also anyone cna help me online to change vender id using rswrite or pdocwrite.
Ayyub
Click to expand...
Click to collapse
Can you post what is written on the bootloader screen?This will help define what rom you need to flash.

thanks lakeman
my bootloader tri color screen shows
I hv a new htc Athena (ameo t mobile uk locked).
I was trying Athena unlocker by olipro. I hv used this on a number of occasions and no problems.
With the present one it was on rom 1.12 tmobile uk and while doing Athena unlocker it crashed on first step.
In bootloader mode it shows
Athe100
Ipl-v1.00
Athe100
Spl-v1.10. RP00
It keeps giving invalid vendor id error 294 when I try to flash tmobile original rom
I have read olipro message who say that I can only repair this via pdocwrite. Apparently it’s the spl that’s corrupt so I need to repair this.
I will be very happy if u can help me with a step by step guide to repair the spl using pdocwrite or rswrite to change vender id.
I am using windows xp or windows 7 and I hv tried mtty and I can successfully connect to Athena and do info 2
It shows level=ff ie it is still locked cid.
Wdata also seems to work but even after password says pass I do not really know how to change the device id or vender id
Device id shows HTCS Þ?ÒtHTCE
I am told y olipro that this device id or spl can only be repaired via pdocwrite.
How can I do it..
Pls help me u can email me on [email protected] or hotmail.com and can add me so u can please provide me with a step by step guide repair my athena ameo
Ayyub

Imate JAM says USB on lcd

Hello everyone!
I have one imate Jam that's showing USB v1.02 on lcd n it's doing nothing at all. Cant even connect it to pc or anything at all. tried to put it in boot mode but nothing happened.
Wat can be wrong? tell me procedure for fixing this!
Regards
Tom

Showing USB1.xx is the bootloader mode ! Maybe a damage switch ?
I would try to flash it .
Cotulla says : *Enter bootloader mode on device (Press POWER + CAMERA + RESET, you will see Serial/USB at top and 1.0X at bottom)
*Connect via USB to PC
*Run Update.exe
*Follow instructions in Update program.
*At the end you should see at device screen: "100% Upgrade OS Image Complete".
*After flashing press reset.
*Don't touch device, wait while "welcome screen" appear.
*Press screen, do calibration and start using device.
Good luck

Have the same problem, tried flashing but update program doesnt pick up the phone and then errors... Im using windows 7, could that be the problem?

Thanks for sharing info..
Can u tell me what rom to flash my imate jam with? I m new here don't know much about imate flashing. can u give me the link for the rom here please??
Regards,

*Connect via USB to PC
*Run Update.exe
*Follow instructions in Update program.
*At the end you should see at device screen: "100% Upgrade OS Image Complete".
*After flashing press reset.
*Don't touch device, wait while "welcome screen" appear.
*Press screen, do calibration and start using device.
Where to download rom from?? update.exe?? where to get that from?

wihandw said:
Have the same problem, tried flashing but update program doesnt pick up the phone and then errors... Im using windows 7, could that be the problem?
Click to expand...
Click to collapse
Fix it like here described, its in german but you will understand it.
The Magician must be in Bootloader mode for this procedur.
View attachment 298939
To be sure that your MAgician is o.k. flash a ROM from your Provider. Also you can get Cotullas WWE3.03 ROM from here http://cotulla.pp.ru/Magician3.html
Be sure that you have Radio 1.12 on your Magician ! ! ! !

cum instalez radio 1.12? cum imi dau seama ca este instalat. please help me