Related
Hello,
i tried to update my BA with wm6.
after flashing it stuck in bootloader(blue,green,red,white display) with the line "R 1.10.00" and nothing more...
even hard or softreset do nothing.
what can i do?
ok i even try the Stuck at startup method.
that's the output of Multiport TTY Version:
set 14 0
HTCST ÚÈÒHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>task 0
it always stuck in blue,green,red,white screen after run multiport tool. what can i do?
------------
i have this problem because of this flashing method:
i entered the grey screen (with serial/usb in first line). then i put my usb connection on and run the rom_update. after it is finished (succesfully) it stuck in the blue, green, red, yello screen! help please...
how did you hard reset?
hello,
i hold down the power-button and at same time put stylis in reset.
hard reset for both WM5 and WM6 is different from the one you're doing. here's the guide...
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
good luck!
ok thanks, i have tried this:
i do softreset. whenn the stripes came i push "records and "camera"(media player button because there is no camera)---> nothing happens. it stops with the line R 1.10.00 and the coloured stripes.
i dont knwo what to do.
the bootloader method is running. i hold power and record button while i softreset. but with color screen it wont work.
they is no camera button (it is media-player button) because there is no camera. its an german xda III (blue angel).
the next problem is i dont knwo what os is right now on it. befor flashing it was wm2003 and flashing says it was successfully. i dont know if its wm6 or wm2003!
ok now all is happen...
the xda says nothing. it dont go on, it dont work anymore. no lights when in cradle, nothing.
can i do anything?
1. Take the battery out, wait a moment, put it back, do not turn on. Put in the cradle and try to charge it. Use power connection (from power supply), disconnect USB from the computer for charging. Amber led should turn on.
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
jakubd said:
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
Click to expand...
Click to collapse
it was not unlocked befor i flashed with bootloader-method.
i charged the battery in cradle (withoud the blue-angel). the led first went orange, after a while turned green (fully loaded). put it back in BA an nothing happens. then put BA (with battery) in cradle and the led became red.
no action on devide, no feedback, nothing. it wont turn on but led is still working.!?
jakubd said:
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
Click to expand...
Click to collapse
ok i get it. in display is the "USB" & "v2.07". now i can flash. but my problem is the phone is not unlocked yet. what file can i flash now??
This message tells you are in bootloader mode. Now you can perform normal flash - I would propose you to use tested&working rom (WM2003?). If this works fine, try again to upgrade to WM5/WM6.
BTW: if you disconnect USB (take out BA from cradle) it should show Serial instead of USB.
ok big tanks to the forum. i finally get it. wm6 german on blue-angel!
Same thing here... but worst..
My 9090 is stuck at bootlader...
When i try to update, (i press the power, record and reset), it says:
SERIAL (or USB)
DOC VERSION IS ERROR!
v2.08
Any idea???
that's normal...
try to flash/update your BA in that screen.
the easy way to go into bootloader mode is to execute a file called Enter Bootloader.exe ..it comes with the rom u download..( well it came with xplodes )
Note:- you have to execute this file directly on your deive not on your desktop PC...and i have only tested this on WM 2003..maybe it will work with wm6 also
SilverSamurai said:
that's normal...
try to flash/update your BA in that screen.
Click to expand...
Click to collapse
I there...
I just updated to BA_TMNL_14200_119_11300_Ship, but only with Maupgrade, couldnt do it with baupgrade...
The problem is that i cant put extended rom, whem i try to upgrade is allways an error... and in the settings i dont have extended rom instaled...
Besides that the batery only last 1hour and the PDA is always freezing... i'm always doing resets...
any idea??
Sorry for my bad english by the way...
Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.
Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370
whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.
beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader
It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.
here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.
Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.
crap, my phone just ****ed off again. Same deal as before. Hate being broke.
help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you
what is your bootloader version
htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3
are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.
tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41
You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.
Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe
yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17
Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.
Hello mates,
My i-mate Jasjar doesn't start any longer. Here's how I got here. I tried to flash my jasjar with Crossbow ROM using ROMUpgradeUt.exe but it didn't do anything. So I went into the Country_ID_Error folder on the computer and executed MaUpgradeUt_noID.exe. My jasjar froze after this and everytime I restarted it just hung on the bootscreen that says i-mate.
So I tried using mamaich method using mtty and now I can't even get to the i-mate bootscreen. So nothing just happens when I try to power up the phone (I'm sure the battery isn't dead).
All I can do is just enter the bootloader mode. That is the only thing that I can do that I know.
Please suggest something. I'm lifeless without the i-mate.
Thanks and regards,
Aditya More.
i had this same issue, i task28?'d my device, whatever command that resets the flash structure, then booted into bootloader, and flashed this file:
http://rs507.rapidshare.com/files/184081773/JASJAR_WWE_11353_137_10301.zip
that should fix you up real good, hopefully.
Well thanks a lot. But it doesn't help. It gives me a connection error when everything is fine. USB is connected, ActiveSync USB connection is disallowed.
I forgot to mention, that when I task 28'd my device, nothing showed on the device. It just showed USB at the top and v2.01 at the bottom for ever, which means the task 28 wasn't probably successful or I ain't sure what.
Yeah, I had to ask you how if the above given file will work if the phone is in bootloader mode.
To fill you on more details, my phone somehow strangely starts. I'll explain how.
When the phone is switched off, and when I press the reset button, nothing actually happens, no activities can be observed.
When the phone is switched off and I connect it to the computer via USB, it shows the charging light. Now when I press the reset button with the phone connected to the USB, the charging light goes off and the USB detection sound sounds on the computer and the computer shows "USB Device not recognized". This means the phone started.
But strangely in both the above cases, none of the two lights on the phone indicate anything and display of the phone shows absolutely nothing.
The only thing I can do with the phone now is enter bootloader.
Also, since I compromised so much, is it possible that I can still flash it with WM6? Because going back to WM5 will make me feel miserable.
Thanks.
@cheapusenet:
I tried flashing with that file. It flashed successfully, but the screen is all smudged. I soft reseted the phone too (using reset+two soft keys) but it keeps displaying that same smudged screen.
Good news is it did something.
Bad new is that it didn't make the mate work.
Please help. I'm dying without the phone.
Thanks and best regards,
Aditya More.
is it possible you can get a picture of what screen its showing? I THINK it happened on mine as well, did you let it sit for 10 or so minutes? if i recall the bootscreen was all corrupted but it started into WM5 just fine.
and regarding wm6, i'd attempt to get the device working before you try and get fancy. is the device cid unlocked? mine was and thats what was causing the issues.
Originally Posted by mamaich
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
if you didnt run that exact command, it's probably a good idea.
and you could try reflashing that stock imate rom?
This is all that happens.. I have waited for 5 minutes. I'll wait for 20 minutes now.
i waited for 30 minutes.. no go..
yap it did that EXACT same thing to mine.
reflash it, i think that fixed mine.
if that doesnt work, attempt flashing some custom roms.
is it CID unlocked?
i flashed it twice.. no go..
what's CID unlocked?
CID
Read the Wiki on my sig link
cid unlock allows flashing of roms that don't match your device branding.
i don't remember what brought me back from that, i may have flashed a custom rom with the imate cid settings in it? i don't remember.
i'll post a rom that i think may have helped in a few hours, I have slow upload speed. until then, just keep tinkering.
also, you should only be flashing nk.nbf. not the ms, or radio nbfs.
http://milfweed.info/UNI_AKU3_2_WWE_IVAN_beta_4_extrom_public.rar
try that rom.
hey man.. Flashed the rom with Ranju's ROM of WM6.1.. it worked.. But I can get the phone to be turned on. i mean device turns on but I can't make or receive calls or text. Let me check the thread of that rom. Thanks a ton for your support. Really appreciate it.
Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou
Samuel ben jamin said:
Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou
Click to expand...
Click to collapse
wel its saying spl so its original spl and not hspl
if you downloaded the german rom form the xda site it doesnt work as the spl in that rom isnt for youre device
if youre in bootloader try to flash hspl on it and then you can flash roms from the site
the other option is got to htc official site and look up the blackstone
there search the latest rom
if you want to download it you have to enter youre imei(can be found under the battery) with that code the rom youre going to download is only for oure device and is supposed to work for you
hope it helps
Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..
Samuel ben jamin said:
Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..
Click to expand...
Click to collapse
In activesync (or windows mobile device centre) go to connection settings and make sure that "allow usb connections" is ticked. Then retry connection device to computer. Put device into bootloader while connected. Does bottom of bootloader change from "serial" to "usb" after a couple of seconds?
In activesync "allow USB-connections" is ticked.
In the white, bottom part of the bootloader is written "USB" when connected to Computer. But if I connect it to the charging unit and start in bootloader, the white field is empty. I can't start it without any electricity source. Either there is another problem with the battery or, because you can't turn it off, the battery is flat all the time.
Also, the original htc blackstone rom-program, detects a connection to the phone, and is loading the rom properly, it seems. Because I could turn the bootloader screen back to where I already was once (by loading the official rom again):
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
Somehow it seems, that the power button is not working, I can't shut down when it is in bootloader, and can't really start the unit. But it's hard to say, 'cause it's starting automatically.
thanks
Hello,
I've got a C500 and i've tryed to flash the bootrom with MTTY and it gave me an error. My phone starts and stuck in bootloader and my computer can't see my phone when connected via USB. Any solutions???
Did you already update the SPL to the patched 1.09 version?
If so then usually you either missed to push the "0" button when the SPL asks you "do need an IU" or another application holds the USB - usually it is the Active Sync. Go to AS "Connection Settings" and deactivate USB connection.
To get the "IU query" you have to push the camera button when switching on and keep it pressed until that query comes.
To get better help you need to tell the exact steps you have done, so no guessing is needed.