[Q] The only thing that's working: bootloader - Touch HD General

Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou

Samuel ben jamin said:
Hello together
wish you nice eavening!
My Problem is the following: The only thing, on my htc touch hd T8282 that seems to work, is the bootloader.
Til five minutes ago I could read there:
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
now the following is added:
in the right, top corner: RUUNBH
in the green field: Upgrade ROM code error, Please try again
I think, this is because, in my helplessness, I interrupted the flashing process. But that's not the main problem.
Beside that, I can "start" the phone only by plugging in the USB cable from Computer or charging station. Then the phone vibrates, and the "smart mobility" screen comes up. After about 5 seconds it starts again, doing the same.
I tried hard resets, but it doesn't work. The only reason why I'm still trying to repair the phone is, that the bootloader is working. To me a signal, that somhow not everything is lost, but maybe I'm wrong.
I tried to flash the phone too. I tried first with the official "BlackStone_GER_1.56.407.2_Radio_52.60.25.33_1.12. 25.16DE_Ship.exe" which worked in the bootloader mode. At least the screen "flashing was sucsessful" showed. The bootloader was the same and nothing changed.
After that I tried with "HSPLWrapper_Blackstone_156OliNex.exe", which is not working. It demands a connection with the ActiveSync, which I have on my Computer, but the only way the computer detectes the Phone is in the bootloader mode. In normal mode computer and active sync don't detect a phone.
So my questions to you:
Do you know a way to load the hard spl (from OliNex) to the phone, although I cannot connect it to ActiveSync? There should be one, because with the official data it "works" (or seems to).
Do you have any help?
Thankyou
Click to expand...
Click to collapse
wel its saying spl so its original spl and not hspl
if you downloaded the german rom form the xda site it doesnt work as the spl in that rom isnt for youre device
if youre in bootloader try to flash hspl on it and then you can flash roms from the site
the other option is got to htc official site and look up the blackstone
there search the latest rom
if you want to download it you have to enter youre imei(can be found under the battery) with that code the rom youre going to download is only for oure device and is supposed to work for you
hope it helps

Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..

Samuel ben jamin said:
Thankyou for writing!
I downloaded and tested the rom from the htc site. I can run that and it comes up with the "successful screen". Then, the phone restarts, and I have the old problem, nothing changed.
As I mentioned before, I can not flash the hard spl from OliNex. That's my big problem. Because, also mentioned before, my phone is not recognized by the active-sync programm and in bootloader mode the HSPLWrapper from OliNex doesn't work.
hope there are some more replies and answers..
Click to expand...
Click to collapse
In activesync (or windows mobile device centre) go to connection settings and make sure that "allow usb connections" is ticked. Then retry connection device to computer. Put device into bootloader while connected. Does bottom of bootloader change from "serial" to "usb" after a couple of seconds?

In activesync "allow USB-connections" is ticked.
In the white, bottom part of the bootloader is written "USB" when connected to Computer. But if I connect it to the charging unit and start in bootloader, the white field is empty. I can't start it without any electricity source. Either there is another problem with the battery or, because you can't turn it off, the battery is flat all the time.
Also, the original htc blackstone rom-program, detects a connection to the phone, and is loading the rom properly, it seems. Because I could turn the bootloader screen back to where I already was once (by loading the official rom again):
BLAC 100 32M
SPL-1.54.0000
MicroP - BlackStone (LED) v6
Somehow it seems, that the power button is not working, I can't shut down when it is in bootloader, and can't really start the unit. But it's hard to say, 'cause it's starting automatically.
thanks

Related

stuck at boot loader -cant connect to pc

Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!

Problem with USPL - dead after trying to CID unlock

I CID unlocked my HTC 3300, and instaled original HTC WM6.
It worked, but it was with 2.xx.xx radio, so I decided to upgrade it to 3.34.90
I started USPL (because i read in this forum that it need to be done before upgrading radio) and command prompt window with "initialisation" (or something like that) worked fine, until 100%. Than it started to upgrade ROM. It also finished to 100%, and then reported an error.
Since than, my HTC is dead.
It doesn't switch on, it doesn't react on USB cable, it can't enter bootloader mode (keeping voice record button, while pushing reset button).
What I need to do to revive it?
Thanks in advance.
Does the USB connects?
Try to reset the flash with MTTY.
No, when I connect it to USB, nothing happens. Neither orange LED blink, nor PC beeps like when USB device is found.
I tried to use mtty, but it does nothing. Apsolutelly nothing. I enter password and other commands, as sugested in some topics, but nothing happens.
I think that mtty doesn't see it at all. I can select COM3, regardless if HTC is connected to USB or not.
Next step?
Today I connected HTC on lab power source. When I try to switch it on, ampermetar shows that there is a flow of current through the circuit, but HTC remains switched off.
Anybody?

Dead Wizard, please help

Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.

help me - Frozen operator screen, unlocking, flashing and usb connector.

Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.
Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370
whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.
beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader
It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.
here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.
Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.
crap, my phone just ****ed off again. Same deal as before. Hate being broke.
help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you
what is your bootloader version
htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3
are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.
tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41
You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.
Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe
yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17
Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.

Screen won't turn on?

Hello,
I've got a problem with my Blackstone. I just flashed the latest topix Rom trough SD card and all went well (rom update:succes), and then i did a HR. But ever since then the screen won't turn on. I tried to softreset, hardreset, removing the battery for a few minutes and turn on, and entering bootloader. The screen stayed black. When i plug in the usb charge cable the orange led does go on, and when i press the power button the phone vibrates for half a second and plays the bootsound (as usual). I can even get an activesync connection with my pc.
Suggestions anyone?
Edit: Just flashed a new Rom (the latest energyrom); screen still stays black. I am still able to get an activesync connection + orange/green led
EDIT2: people in this thread seem to be having thesame problem I have with my blackstone. It seems to be a hardware defect... Now let's hope it will be repaired under warranty
Ok, I'm replying instead of editing because I've got a new problem now
I want to return my phone to claim warranty. I did manage to flash a stock rom + radio, but the problem is i use hspl and i am unable to flash a stock spl to the device. When I run the Hardsplwrapper-Blackstone.exe (doesnt matter wether its the unsigned olinex or the 1.56 olinex version) I get a 260: connection error when i use Windows XP, and a 202: connection error when using Windows 7.
The wiki says to run SSPL manually from a file explorer in your phone... But without a working screen that is a bit hard. I als don't have any screen viewing app installed on my device...
EDIT: also tried installing mymobiler to be able to view the screen but I am unable to connect...
Anyone?
I managed to flash stock spl by putting the device in bootloader manually while I had it connected to usb. Then I waited til the bootloader connected to my pc (I could tell because the "new hardware found"screen popped up). then I ran the hspl.exe and copied the stock .nbh spl file. After that I was able to finish the wizard
ok, another question (sorry mods for replying to my own thread _again_ )
I flashed a stock rom + radio and stock SPL (version 1.14). Is this enough to be able to claim warranty, or will HTC find out that i've been using HSPL and custom firmwares? I wouldn't like to have to pay for repairs because they find out about that.

Categories

Resources