Hello,
I've got a C500 and i've tryed to flash the bootrom with MTTY and it gave me an error. My phone starts and stuck in bootloader and my computer can't see my phone when connected via USB. Any solutions???
Did you already update the SPL to the patched 1.09 version?
If so then usually you either missed to push the "0" button when the SPL asks you "do need an IU" or another application holds the USB - usually it is the Active Sync. Go to AS "Connection Settings" and deactivate USB connection.
To get the "IU query" you have to push the camera button when switching on and keep it pressed until that query comes.
To get better help you need to tell the exact steps you have done, so no guessing is needed.
Related
help please i can not sync using bluetooth because of the bluetooth option on my active sync is lacking. i can only see the 115200, 19200, 38400, 57600 and USB... any patch for this? thanks...
also, why i can not make any upgrade? my rom version is 1.11, i want to upgrade it to 1.12 or 1.13... everytime i put my device into bootloader, there is data (version of rom and radio) read into my device please help... thanks
I did not quite understand your second question. When you see the rom version number and radio rom number, then you are not in the bootloader mode.
I think you might mean that you cannot get into the bootloader mode. In that base, you need to do another hard reset when you see the boot flash. Actually you need to do TWO hard resets to get the bootloader mode - first reset to the start flash, then before the start flash disappear, do the second reset.
OK, to get bluetooth Active sync working, you can view my guide HERE
To get into Bootloader mode, you need to hold both the camera and power buttons and hit the reset button with your stylus. Continue holding the camera and power buttons until you see "USB 1.0". You wont be able to turn on the backlight when this appears but you should be able to see it ok if you're indoors.
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Leiden said:
Whats needed:
TyphoonNBFTools: http://w1.whatcounter.com/dlcount.p...yphoonNBFTools_0.3_SPL1010064_SPVServices.zip
Any Official Rom (I used I-Mate SP3 WWE).
A Typhoon running Windows Mobile 5.0.
Reverting Back:
Run TyphoonNBFTools and Open the SPL1010064.nbf. Right click on SPL in the bottom part of the screen and choose Emergency Flash. If this is the first time you have used the program you will get a prompt on your phone to run the runtimes. Choose yes. Click OK to flash the new bootloader to your phone. Next disable Activesync by turning off USB connections. Turn off your phone. While holding down the Camera button insert the USB cable, the phone should run the bootloader and you will be presented with the tri-color screen. It should say USB in the bottom corner. Now run Mtty and choose USB connection. Hit enter in the blank white space. You should now see Cmd>. Type "info 2" without the quotes. You should see some information about your phone. Next type "format BINFS" agains without the quotes. This one is case sensitive. You should see format complete or something along those lines. Now close Mtty and re-enable USB connections. Run the exe from the update you downloaded and follow the instructions. Your phone should now boot back up to WM2003.
For those stuck in bootloader mode you will need to run mtty and reflash the wm5.bin to the phone then follow the steps above.
Click to expand...
Click to collapse
Man! Can't thank you enough for this. I took my phone to the service centre, willing to pay for the repair, and they could not do it. Every thing works fine now. Very good manual, clear instructions and correct info!
THANKS!
Hi
I Am Trying To Follow The Procedure Mentioned. But When I Right Click On Spl I Am Not Getting 'emergency Flash' Active.
Can U Please Assist Me Regarding This
You need TyphoonNBFTools.dll installed on your phone. Try running TyphoonNBFTools and selecting Tools->Immediate Flash Tools->Test Immediate Flash. It should automatically install the required stuff for you. Check you phone when you run the program. You should get a prompt to installed a program from unknown publisher. Make sure to choose yes.
Stuck in bootloader
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
maybe u need to make a "goldcard"
my feeler (o2 xphoneII) lives again after flash with goldcard.
I can't find a way to create one for Typhoon, can you point me in the right direction?
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
er1cc said:
I try flash Amadeus = Qtek 8100 with UpdateTool from Qtek 8310.
Update process stopped at 74% , and UpdateProgramm closed.
Now my Qtek 8100 not Powered ON , and can't enter in boot mode (tricolor screen) with "Camera" button hold + USB cable conneting.
PC don't see any USB devices when I connected my Qtek 8100 to USB port.
I think I erased Boot loader in my Qtek 8100 (but not sure).
Is any method for repair ?
WBR !
Click to expand...
Click to collapse
UR Phone is fried!
this happens to almost 1 out of 20 users.....that while downgrading/upgrading to another bootloader, ur phone becomes dead....
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
get the tricolour bootloader type in mtty info 2 the type format BINFS then upgrade using rom upgrade
DomConway said:
Just trying to do this following my question here.
I though it was going well but I have a major problem now! I managed to do the emergency flash, but every time I boot I just get the tricolour bootloader screen (IPL 1.00, SPL 1.01.0064) and can't get any further. Any ideas please? I have tried using mtty to load wm5.bin but get the error "MTTYDownloadImageNot allow operation!"
I have also tried re-doing the "format BINFS" and doing the above again but still no joy.
Any ideas would be much appreciated!
Click to expand...
Click to collapse
i also got that problem but i reinstalled the patched RUU again and my phone now boot but i have not been able to go back to the 2003 as i insalled WM5 but still cant format the BINFS
If already have patcher the bootloader with the guide to upgrade to wm 6.0 can I ignore to do it again? I mean flash bootloader again ?
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen
anyone?
ideas?
Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!
every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck
Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.
I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in
Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.
Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight
thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!
I CID unlocked my HTC 3300, and instaled original HTC WM6.
It worked, but it was with 2.xx.xx radio, so I decided to upgrade it to 3.34.90
I started USPL (because i read in this forum that it need to be done before upgrading radio) and command prompt window with "initialisation" (or something like that) worked fine, until 100%. Than it started to upgrade ROM. It also finished to 100%, and then reported an error.
Since than, my HTC is dead.
It doesn't switch on, it doesn't react on USB cable, it can't enter bootloader mode (keeping voice record button, while pushing reset button).
What I need to do to revive it?
Thanks in advance.
Does the USB connects?
Try to reset the flash with MTTY.
No, when I connect it to USB, nothing happens. Neither orange LED blink, nor PC beeps like when USB device is found.
I tried to use mtty, but it does nothing. Apsolutelly nothing. I enter password and other commands, as sugested in some topics, but nothing happens.
I think that mtty doesn't see it at all. I can select COM3, regardless if HTC is connected to USB or not.
Next step?
Today I connected HTC on lab power source. When I try to switch it on, ampermetar shows that there is a flow of current through the circuit, but HTC remains switched off.
Anybody?