Related
Hi,
I tried some ROM from this website to change my wizard to wm6.
When the RUU finishes at 100procent my device restarts and normally it should be flashed. But mine always restarts the original rom. On the pc it says that the procedure has finished succesfully.
Dont know if this has anything to do with locking, but I used the lokiwiz to unlock my device.
Anyody an idea to solve this?
Grtz
Annihil8
your wizard is still CID locked...
try it again ... follow the instructions ... read carefully the messages when running lokiwiz ... could be misleading sometimes at a first glance ...
I'll give it another try. But the lokiwiz keeps telling me that the device is unlocked. It doesn't even give me an error like you get with the AKU2.
error:itwritedisk-an internal error occurred
So that is why I think that should be ok...
you may want to use the WST tool to check the CID status ... you find it on this forum. don't have the link on hand right now ...
Hey folks,
I got the T-Mobile SDA and it's allready running WM5, so I skipped step 1-4 in the how to and wanted to flash the patched ruu from step 5.
But whenever I start the flash tool it starts fine, checks version and then boots into the bootloader mode (the one with the color bars). But after that it wount start flashing. After a while it aborts with a communication error. Also when it switches to the bootloader mode the activesync connection disappear, which I assume is correct, but from my mda2 which I flashed couple of times via the bootloader I remember that when it went into the bootloader some sort of device was discovered from windows. with the sda it's not the case.
Anyone got an idea what is going on here? I thought after I flashed wm5 on the damn thing getting wm6 on there would be a piece of cake...
thanks for your help!
4saken
_4saken_ said:
Hey folks,
I got the T-Mobile SDA and it's allready running WM5, so I skipped step 1-4 in the how to and wanted to flash the patched ruu from step 5.
But whenever I start the flash tool it starts fine, checks version and then boots into the bootloader mode (the one with the color bars). But after that it wount start flashing. After a while it aborts with a communication error. Also when it switches to the bootloader mode the activesync connection disappear, which I assume is correct, but from my mda2 which I flashed couple of times via the bootloader I remember that when it went into the bootloader some sort of device was discovered from windows. with the sda it's not the case.
Anyone got an idea what is going on here? I thought after I flashed wm5 on the damn thing getting wm6 on there would be a piece of cake...
thanks for your help!
4saken
Click to expand...
Click to collapse
by the sound for this you have allready got the bootloader the right one. if it says spl 1.01.0109 on the green part of you bootloader then you can flash wm5 or wm6 these no need to flash the patched ruu
lol, ok. it's flashing now! I didnt think I already had the right version. But you were right. it said 1.01.0109 in the green bar.
let's hope it goes trough without a glitch
Hi,
Does anyone knows a method for repairing my old P3300.
The problem is i've tried to upgrade to wm6 and something went wrong,
ATM i only have a screen with the Tmobile logo,
I can open the bootloader, but if i load the bootloader and try to run the official rom update i get the error 122 cannot connect to device.
If i'm in the bootloader and try to start mtty, it all goes as it is supposed to go
I can see the phone in mtty and can get it into flash mode when i enter the bootloader password.
Even when the phone is in this mode the official upgrade won't see the device.
So my question: is there a way to flash/upgrade the rom from mtty?
If yes what are the commands for it in mtty.
If not does anybody know an other solution?
Btw it's a sim unlocked and Cid unlocked P3300 From the Netherlands Tmobile.
IPL 1.13.0001
SPL 1.13.0000
GSM 02.49.90
OS 3.4.0.0
Thanks
Janus
Same here, I think we need the original T-Mobile rom.
RaZoR X said:
Same here, I think we need the original T-Mobile rom.
Click to expand...
Click to collapse
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.
neilhhardy said:
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.
Click to expand...
Click to collapse
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.
Which device are you guys trying to flash with a new ROM, if its a UK T-Mobile device its not got the WiFi hardware so don't go putting a ROM on the device that expects WiFi support, T-Mobile Artemis units from Holland did have WiFi built in as does the true HTC P3300 unit, the UK T-Mobile device does not - Mike
RaZoR X said:
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.
Click to expand...
Click to collapse
ok hear'd this one many times before, your running vista >?
try and search the forum, there is a fix for this then your phone.
@Mike it's the "Dutch" version with indeed WiFi
@Neilhhardy
No, I'm not running Windows Vista at the moment.
Me too have the same problem - flash allways stop at 2% , also can`t flash radio - stop at 73-75% - any idea?
the phone is original HTC (have Wi-Fi and not branded) - never CID locked go to bootloader without any problems but can`t flasing - I think case problem is standart HTC flasher exe - for early models have different flasher software - I have Jaf WM but Jaf WM do not support Artemis - did have released other soft that alow flashing Artemis?
P.S - I thing cause right solution is to flash your device with original version - the OEM version that was instaled by factory will fix the problem
this worked for me on a unlocked mda compact 3
format your memory card first with your pc then copy the rom file (nbh)to your memorycard and rename it to ARTEIMG.nbh
start bootloader and follow the instructions.
http://wiki.xda-developers.com/index..._Card_Flashing
rom i used http://makus.folijka.pl/OrbitO2UK.rar
I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)
I did a reset with the rec, pwrbutton and resetbutton. And now he's up and running agian with WM6 Haha
I tried to unlock the device with the AthenaUnlocker, but I got this error:
0x0, 0x100000, SPL-verify.nb
I think I killed him lol
ppl said:
I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)
Click to expand...
Click to collapse
this may had worked for you but at the HTC website I get the error that my phone is not branded. true it's a tmobile phone...
can you give me the serial number you entered? if you dont trust it you may make the last 3 digits a X
thanks
Janus
My heads spinning from all the information aka post and threads, but im still stuck like my wizard on the 2nd splash screen.
I wasnt trying to upgrade the rom jst clear storage but after everything ive read i would like to upgrade to wm6 but first i want to get my wizard working.
I tried backing up the rom to the sd card but I get "You didn't get the proper security level to download a specific image" So i take it my wizard is cid locked.
My IPL:1.01 and SPL:1.06 does that mean its a g3. My activesync 4.5 doesnt pick up my wizard is it because it cant boot, i tried with it in bootloader mode still doesnt pick it up.
So plz point me in the right direction to fix my wizard
ok i think the place where im stuck at is cid unlocking my wizard with out using that imei site. any help or is there another way to do this.
This helped me when I was stuck on the first screen. For some reason, the Radio file was gone. Follow this exactly, it works. In my case (sounds like yours also), at the end of this you will at least have access to the phone again.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=bootloader
After your done. You will have a RGB screen, then follow these directions to load a base rom and unlock so you can keep going until you ca load WM6.1.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I've had many, many problems over the last 3 days trying to do this. I completed it all in less than a day, but when I used the phone it had terrible reception. I completely downgraded everything back to square one. Still bad phone reception. I was about to through it out the window, when someone called my wife's cell phone and she also had bad reception. I then put my sim in another phone, same problem. Well, at&t has a tower down for the last 3 days. What timing, it seems to work when not at home, but hard to test that way Anyway, moral of the story is. Don't give up, keep plugging along.
Good luck.
I'm pretty sure imei checker is for SIM unlocking.
For G3 CID unlocking and upgrading read the stickies in http://forum.xda-developers.com/forumdisplay.php?f=289
If you can start your Wizard in bootloader, and it says "usb" in the lower-left, you can flash your original ROM. An active sync connection is not needed. Search for your carrier's ROM if you don't have it and I'd recommend the "no carrier ID" version of the RUU.
Have you tried a 'Hard Reset',hope it'll work,if it boots up into working OS and it already has IPL/SPL 1.xx,use lokiwiz02b tool to SIM/CID unlock the phone and than upgrade.
If it doesn't work still after Hard Reset,most probably,its Extended_Rom is corrupted,its required to reflash a new rom.
Activesync doesn't work in absence of a working OS and in Bootloaders mode.Its not required for flashing a rom.Just get the phone into Bootloaders and hook the phone with pc via usb cable and watch small usb appear at the bottom of the bootloader screen,if its there,it good to go and flash the rom.
ok so i downloaded the button rom finally but how do i flash it to my wizard.
Get your phone in Bootloaders,hook up the phone with pc via usb,watch small usb appear at the bottom of the Bootloader screen,if its there run the 'RUU' application,it'll start to flash,it stops at a certain percentage,don't get worried and do anything,after a couple of minutes it starts again,let it complete 100%,the phone'll restart and boot up in new OS.
which ruu application. I jst downloaded 1 which comes in the form of a rar file saying ruuwrapper. is that the right 1
So after lots and lots and lots more reading i realized i dont need a ruu. all i need to do is get into bootloader mode plug in the usb and run the wizard button rom. It worked perfectly my wizard is back to life yip pee.
Anyway i wud jst like to thank u guys for all the help and compliment u guys on a gr8 forum.
Now my next challenge is wm6 with touch flo.
i must admit i am a newbee... i read the thread thoroughly and downloaded the programs necessary to flash my HTC Touch P3452. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM, the version in phone was 2.20.0000 and new is IPL USPL 2.26. then i cliked update and the progress bar appeared on my PC. then after a minute, i gor an error (266) stating that updater cud not connect to the p[hone and asked me to check connection. i didnot do anything. after a while, i noticed a white screen on my phone and progress bar stuck to 0%. now my phone is dead.
can anyone help me
katbasav
Read this http://forum.xda-developers.com/showthread.php?t=406721, something I hope will help you.
Good luck
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
katbasav said:
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
Click to expand...
Click to collapse
tito12 said:
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
Click to expand...
Click to collapse
katbasav said:
the version in phone was 2.20.0000 and new is IPL USPL 2.26.
Click to expand...
Click to collapse
If you are able to enter the bootloader tricolor screen and you see that you have indeed USPL 2.26 installed, then you should be able to flash anything you want!
Fully charge your pda
Remove your memory card and SIM card
Connect via usb, enter bootloader and flash the Rom you want with the RomUpdateUtility.exe
WARNING
Since you don't have HardSPL but USPL be extra careful NOT to flash a Rom that includes SPL cause then your device mightwill get CID locked.
If the above steps don't get you with a working device, then better check if the USPL really worked.
A safe way to find out if your CID unlocking worked is following this method & check the line:
Code:
g_cKeyCardSecurityLevel = ?
;If ?=0 => Touch=CID_Unlocked => Able to flash any ROM or Radio Update through Bootloader
;If ?=FF => Touch=CID_Locked => Try CID_Unlocking again BEFORE flashing anything
Click to expand...
Click to collapse
Regards!
My mobile is HTC Touch P3450. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM & installed its working, but i tried RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe rom but my mobile is showing "smart mobility" and then mobile is off. Pls. kindly help me.
i tried CID unloking also, but not working
Narashimha