Related
Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.
If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.
g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.
Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.
Thanks for details...
Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725
I really hope someone can help.
I followed the Hard Spl unlock instructions and all seemed to work well.
I then tried to install the original HTC WWE ROM and it froze at 24% reporting an error. I followed the recovery steps but noticed to my horror that the original SPL -1.25.0000 has reappeared.
I am unable to do anything and have the coloured bootloader screen. Attempts to run the Hard SPL unlock freeze at 0% can anyone help please........
What did you do?
Step by step from the beginning!
Step by step to destruction!
I ran the HardSpl unlock utility as per the detailed instructions. It worked well and I saw the new SPL screen. I unplugged the USB as per the instructions and ran the HTC original ROM Rom updater. All went well until IT REACHED 24% on the screen and on the PC - then it froze.
I waited 30 minutes hoping it would unfreeze but sadly............
I then removed the USB cable and attempted a hard reset. This brought me back to the Bootloader screen with the original SPL displayed.
Further attempts to load the HTC ROM produce an error telling me it cannot be installed on this device. I now have a very expensive paper weight.
Any help much appreciated.
pilib said:
I ran the HardSpl unlock utility as per the detailed instructions. It worked well and I saw the new SPL screen. I unplugged the USB as per the instructions and ran the HTC original ROM Rom updater. All went well until IT REACHED 24% on the screen and on the PC - then it froze.
I waited 30 minutes hoping it would unfreeze but sadly............
I then removed the USB cable and attempted a hard reset. This brought me back to the Bootloader screen with the original SPL displayed.
Further attempts to load the HTC ROM produce an error telling me it cannot be installed on this device. I now have a very expensive paper weight.
Any help much appreciated.
Click to expand...
Click to collapse
Maybe here was the problem...
If you have hard-spl on your machine (in bootloader you see Olinex) after you do not have to replug the usb cable.
Just run the romupdateutility.
Now it seems you have original spl...
In this case you can not install not offical rom. You sould try the offical Orbit 2 rom.
I THINK U HAVE TO TRY HARD-SPL, are u shure u,ve done allready?
Resurrection!
In desperation and believing I had nothing to lose I attempted to flash an O2 Artemis
ROM to the Polaris. It got to 2% failed but rebooted the device to the original ROM.
I had previously tried hard and soft restes and could get no further than bootloader screen.
I don't know or understand what happened but my phone is alive again.
I would wan anybody abut the Hard Spl Unlock.....it caused me major hasslr.
Thanks to those who tried to help me.
clearly you didn't get Hard-SPL, you got the soft-spl
congratulations for your massive fail.
Olipro said:
clearly you didn't get Hard-SPL, you got the soft-spl
congratulations for your massive fail.
Click to expand...
Click to collapse
^ Lol, he's the guy who came up with the Hard-SPL, so as you can imagine he's a little pissed off about the criticism.
Confusion
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
pilib said:
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
Click to expand...
Click to collapse
No, it not is the problem of hard-spl.
You did something wrong, according to your step by step guide.
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX.
On the pc run the RomUpdateUtiliy (from the offical rom folder)
After Few minutes pda will reboot, new rom is installed.
Anybody succewssfully changed XDA Orbit 2 ROM?
Could I ask if anybody has succeeded in changing the XDA Orbit 2 ROM for an alternative and if so could you outline the procedure. Many thanks
pilib said:
Could I ask if anybody has succeeded in changing the XDA Orbit 2 ROM for an alternative and if so could you outline the procedure. Many thanks
Click to expand...
Click to collapse
Read the post just above yours.
Sascha
Clarification
I am looking for someone who has actually succeeded - not just the theory!
Here are some:
http://forum.xda-developers.com/showthread.php?t=372665&page=2
Success
I must eat humble pie - it obviosuly was due to some error on my part that the ROM replacement failed. I have now been successful. The Hard Spl unlock works perfectly, and I will send a payment to show my gratitude!
pilib said:
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
Click to expand...
Click to collapse
the problem was you ran the htc ruu after replugging usb in the hardspl unlocker process
edit: sorry i see problem has been solved
cmonex said:
the problem was you ran the htc ruu after replugging usb in the hardspl unlocker process
edit: sorry i see problem has been solved
Click to expand...
Click to collapse
yeah thats what i also think. he didn't compleate Hard-SPL process, when asked for re-plug just ran RUU.
If anyone find a time to help me , about HTC artemis is only stuck on windows mobile screen/logo
..also phone was entering on bootloader mode , three color screen ?
3.15.0000 version T-mobile , but cant fllashing , cant uspl nothing only going to 3% and stopping there.
Any help on this please?
best.r
Hellooooo...
Masters , how to solve this problem , pleasee???????
Radio ROM curropted,
First of all
Try restoring factory settings.
1) PUSH AND HOLD the (-) and (-) buttons over the (ok) and (windows) buttons, then press and hold RESET button.
2) Release reset button. but keep (-) and (-) held.
3) A message will appear and tells you to press SEND to restore factory defaults, SEND = GREEN TEL BUTTON.
4) Press it and wait, see what will happen after, maybe once it's finished you will need a soft reset, I don't remember...
Second Try possibility -if the above will not work-
Try with flashing a new full official ROM
it might be a problem as probably you do not have USPL unlocked!
so your SPL should still be looked to 3,13 or similar.
it would give you a DEVICE ERROR if you update it, and stop at 3%.
if SPL is 1.11 so that's fine, SPL is unlocked.
just enter bootloader and flash any complete (OS + RADIO) Rom, even non factory rom.
if SPL is locked you can save your tel just trying to update and original factory rom.
example: T-Mobile UK, T-Mobile Germany, T-Mobile ....
Note that even if they are all T-Mobile they are different! (Germany is different than UK, and so...)
Desperate last choise
If all the above did not solve,
probably your Radio ROM is curropted and in a bad sector,
use MTTY tool and comands to do a low level format, and remove any residual rom tack.
Do not clean bootloader, you will need it for the new re-flash
Then enter bootloader and flash an official factory rom.
It took me 6,30 hours to save my last Artemis, wish you a quicker solution, so good luck!
mouse.co.nr , thanks for reply mate.
First i have try since from yesterday to give on the phone any fllash , i have try so much diference way to get solution but nothing happen.
The phone cant do a hard reset by presing buttons , the phone was only get on bootloader mode , and was show IPL 3.15.0001 , and SPL 3.15.0000 , and i know that the phone was not cid unlock maybe , but i cant give any upsl and fllashing with fllash that phone.
Second i we try with ART_TMOUK_11311001_024990_WWE_Ship_R3 t=mobile UK , nothing happen , also only radio ARTEIMG_TMO_UK_4.1.13.251_02.92.90_RadioOnly , again nothing.
Radio only , and fllash was going to 3% and stopping.
Artemis_USPL , starting and was going to 100% , but cant finalize i think , bcs ERROR [270]:UPDATE ERROR The image file is corrupted.Please check your update Utility.
..and also i have try to fllash from sd card http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing , i have create one folder with name : root , and i'we put the image ARTEIMG.nbh....but can not starting from sd card also.
i'we download from here all this: http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades , and also from official t-mobile.
what of this list is a good RUU for my HTC?
Best.r
root folder
haveri said:
..and also i have try to fllash from sd card , i have create one folder with name : root , and i'we put the image ARTEIMG.nbh....but can not starting from sd card also.
Best.r
Click to expand...
Click to collapse
...probably a problem is creating a folder with the name root, "root folder" means on your sd-card without any folders... as far as i know...
anyway, good luck trying
haveri said:
the phone was only get on bootloader mode , and was show IPL 3.15.0001 , and SPL 3.15.0000
Click to expand...
Click to collapse
SPL still Locked!
two solutions:
1) USPL (proper one) lately I foundout the official one on the official form was giving me some update errors, I think the file is curropted, and if startuspl.exe does not run till 100%, reboot and start the RUU by itself, it wouldn't work if you maually start the RUU once the original launched after USPL gaves the error.
I'm attaching another USPL try this other one...
2) if your pc does not see the PPC for USPL, try not other WWE roms, it should be for your ARTEXXXX, ther is ARTE100, ARTE110, ARTE1000, ARTE200 ...
try more than one till you'll get the 100% rom update.
Radio Only will not work, you are in bootloader, you have an OS problem! if it gives you the "windows mobile image" and stops there, so it's just the radio, else it's the OS and probably the radio!
do a full ROM updt, official WWE have both radio and OS.
I wish for you that your PPC doesn't stop at Windows Mobile Image (the one after boot image), I have thrown away a P3600 in this way!!! Radio was so curropted that I could not fix it anyway, nither MTTY, required a CIP programming, but I'm not good at...
haveri said:
Artemis_USPL , starting and was going to 100% , but cant finalize i think , bcs ERROR [270]:UPDATE ERROR The image file is corrupted.Please check your update Utility.
Click to expand...
Click to collapse
It surprised me the first time I got a 270, try the attached uspl, I got that from the rapidshare, scanned with norton 2010 and is clean, tested today on a german T-Mobile ARTE100 and it worked (now it speaks french!).
haveri said:
..and also i have try to fllash from sd card
Click to expand...
Click to collapse
Will not work, you can not bypass protections just by running SD bootmode!
if it's locked it's always locked!
haveri said:
i'we download from here all this: http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades , and also from official t-mobile.
what of this list is a good RUU for my HTC?
Best.r
Click to expand...
Click to collapse
I have no idea, try one of each, in the worst of cases it will always block at 3% and bring you back to beginning, Bootloader mode back again and re-flash..
hope it'll help!
good luck
haveri said:
the phone was only get on bootloader mode , and was show IPL 3.15.0001 , and SPL 3.15.0000
Click to expand...
Click to collapse
SPL still Locked!
two solutions:
1) USPL (proper one) lately I foundout the official one on the official form was giving me some update errors, I think the file is curropted, and if startuspl.exe does not run till 100%, reboot and start the RUU by itself, it wouldn't work if you maually start the RUU once the original launched after USPL gaves the error.
I'm attaching another USPL try this other one...
2) if your pc does not see the PPC for USPL, try not other WWE roms, it should be for your ARTEXXXX, ther is ARTE100, ARTE110, ARTE1000, ARTE200 ...
try more than one till you'll get the 100% rom update.
Radio Only will not work, you are in bootloader, you have an OS problem!
do a full ROM updt, official WWE have both radio and OS.
haveri said:
Artemis_USPL , starting and was going to 100% , but cant finalize i think , bcs ERROR [270]:UPDATE ERROR The image file is corrupted.Please check your update Utility.
Click to expand...
Click to collapse
try the attached uspl, I got that from the rapidshare, tested with norton 2010 and is clean, tested today on a german T-Mobile ARTE100 and it worked.
haveri said:
..and also i have try to fllash from sd card
Click to expand...
Click to collapse
Will not work, you can not bypass protections just by running SD bootmode!
if it's locked it's always locked!
haveri said:
i'we download from here all this: http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades , and also from official t-mobile.
what of this list is a good RUU for my HTC?
Best.r
Click to expand...
Click to collapse
I have no idea, try one of each, in the worst of cases it will always block at 3% and bring you back to beginning, Bootloader mode back again and re-flash..
hope it'll help!
good luck
no bootloader possible
hi,
I have tried everything on my T-Mobiel MDA Vario 3.
SSPL-KAIS.exe
JumpSPL 156, 193 and 194
pressing of any keys will not forward me into the bootloader
on my pda is IPL and SPL 3.15
I have also tried HardSPL 329 and 356, no success.
the only way to get into the bootloader is when starting KaiserCustomerRUU.exe, but no ROM is getting installed. I always receive an error 270 file defect. but this is not correct, as I have tested 3 or 4 different files.
does anybody have an idea?
thanks a lot
hds09 said:
hi,
I have tried everything on my T-Mobiel MDA Vario 3.
SSPL-KAIS.exe
JumpSPL 156, 193 and 194
pressing of any keys will not forward me into the bootloader
on my pda is IPL and SPL 3.15
I have also tried HardSPL 329 and 356, no success.
the only way to get into the bootloader is when starting KaiserCustomerRUU.exe, but no ROM is getting installed. I always receive an error 270 file defect. but this is not correct, as I have tested 3 or 4 different files.
does anybody have an idea?
thanks a lot
Click to expand...
Click to collapse
Hi!
Check hardware buttons,maybe one of them is broken,that's why you can't put your device in bootloader.
Make a Goldcard (search) and flash the Kaiser with Goldcard inside.It will revive your device.
BR
Scootie
Hello everybody, with the risk of opening an already discussed thread, I am asking for your help regarding my HTC Elf (or Elfin?).
Initially I tried to change the language from Spanish to English, with the aid of some programs like ELF USPL. The first thing that appeared on the screen when my phone turned on was an Orange(TM) logo and it did not go further than that (it shut back off). After several tries with that program and other .nbh files, I even installed an Onyx release.
Now the phone has the same attitude as with the Orange(TM) logo, but now it appears "smart mobility" and then shuts back off. When I enter the boot screen: on the red colour it says IPL 1.14.0002 and SPL 1.14.0000 followed by green, blue and a little white on which states if the USB is connected.
Can you guide me to the solution, please?
Read this http://forum.xda-developers.com/showthread.php?t=996105&highlight=stuck+in+smart+mobility
You need to find your original Rom then cid unlock. Don't forget to click on the last link too.
Good luck
commission lestist
tito12 said:
Read this http://forum.xda-developers.com/showthread.php?t=996105&highlight=stuck+in+smart+mobility
You need to find your original Rom then cid unlock. Don't forget to click on the last link too.
Good luck
Click to expand...
Click to collapse
Thank you for the directions. I've followed some of them and I am in this stage: I know my device ID: ELF010050 ORANG309, got the original ROM but the same 270 problem which pops up at 2% when the phone resets and then shuts down. My CID is locked and saw in this thread http://forum.xda-developers.com/showthread.php?t=320155 a program called enable-rapi but requires the phone to be on to install the files. Can you help me further, please?
To the best of my knowledge, if you really had Your original Rom it'd have successfully flashed. Any other one will meet the 270 or 2% error. Enable Rapi and the rest is valid before you flash a Rom, so my best advice is to try to find the appropriate one.
After countless tries to flash that ROM, I'm still getting the 2% error. But I've noticed that I can make the tricolor screen display RUU in the top right corner by removing the battery while 0% - 2% flashed and turning the phone back on. But it doesn't work this way either, error 270 still pops up.
At this stage, I'd try other Roms http://forum.xda-developers.com/wiki/Elf_Upgrades
I have tried all of them but with no success. Should I start with these ones now? http://forum.xda-developers.com/showthread.php?t=379034
Try find your cid and device using the same link first and then flash
ELF010050 and ORANG309 are the CID and device, I've downloaded two seemingly original ROMs but I still get the 2% error. They were in Spanish like the original one but still didn't work.
Sorry, running out of ideas...
try creating a goldcard, it should work
Betrakiss said:
try creating a goldcard, it should work
Click to expand...
Click to collapse
Thank you for the idea. Could you give me a link for a tutorial? I downloaded the Axe Box program and didn't install properly, maybe because of its version (5.0) that I got from some FTP server.