Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.
If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.
g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.
Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.
Thanks for details...
Related
Hi, I have a TMobile MDA with IPL 2.26 and SPL 2.26 and I was trying to put a new rom but the program gave me an update error when reached 99% an now it is stuck in the boot screen (shows in the bottom USB connection) but when re-running the program it does not connect and activesync does not detect the phone. Before the rom update program ruu gave me the that said the phone required a newer program version.
Did I screwed the phone or there is a solution?
Thank you in advance for your help and best regards
Issue Was solved downloading from T-MOBILE the updated ROM and executing the program
Nick
Nope, you're good.
As long as you can enter bootloader and it reads usb in the bottom corner, your wizard can be saved. Don't worry about active sync, it won't read. Get a stock rom from your provider...if Tmo, it is available on their website. Plug in the usb and get into the tri-color boot. Run the stock ruu. Do not let anything interfere with the process, so disable your screensaver, don't let cats or kids near the usb cord, etc (trust me on that one!). NBow flash the stock rom. It will take 10 minutes roughly, be patient, DO NOT unplug usb for any reason...let it flash and reboot. Once flashed, make sure you are cid/sim unlocked...use lokiwiz (read the sticky on unlocking). You cannot change roms from stock to custom without first unlocking. If you are already unlocked, once you have the stock rom re-installed, you can flash to a custom rom. The linky in my siggy explains in detail about reviving a "bricked" wizard.
Hi Profs,
there are some problems with a Artemis Update SPL (USPL) v.01. I've found this problem is several topic but there was no solution for it.
#1:
http://forum.xda-developers.com/showpost.php?p=1739577&postcount=413
#2:
http://forum.xda-developers.com/show...44#post1745844
#3
http://forum.xda-developers.com/showpost.php?p=1713596&postcount=1
The problem:
use USPL to get rid of the CID....count goes up to 100% screen shows black with green text, then pops to white. I need to do a soft reset to get it running again.
Then i use ROM Update Utility to update my p3300....and it still keeps hanging on 3%....damn. i get mad...!! Have read almost all here online...no virusscanner, no firewall....I use win XP.
i even tried without memory card and phone card....and nothing seems to work.......
ipl 1.14.0001
spl 1.14.0000
gsm 02.07.90
os 1.14.0.0
Who has any clue...?
With other words:
I've just got back my P3300 from repair, they changed the main board. With the previous main board I was able to upgrade the device and I was using the B&B versions.
But with this new board I'm not able to upgade the SPL. When I try to upgade the device after and start the start_uspl .exe the 10...20... ....100 my device become an interresting "blue screen" status and only the reset help to get out from this status. If I start the RomUpdateUtility.exe after the upgrade I got the error message #270
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
ExtROM version: 3.12.405.102
This is not the solution for the problem. I've tried it:
Plug in USB cable. Hold voice recorder button and press reset button. Bootloader will appear (Three color stripes). Then you may flash up ROM. (This works only for RUU installation types, not for PDAmobiz modified installator) Original english HTC P3300 ROM you may download form here: http://wiki.xda-developers.com/index...temis_Upgrades ....
Please help us to solve this problem....
Probably the same problem
This should be the same:
Hello POF,
I was directed to this link by Rudegar because I want to change the french ROM to English ROM.
The relevant data of my PDA is:
The version of the ROM: 1.14.406.1 FRE
Date of ROM: 9/27/06
Radio version: 02.67.90
Protocol version: 4.1.13.28
ROM extension version: 1.14.406.101
I tried exactly the way you described in the USPL_manual and everything went well till I got to a stage where I was asked to click the update button which I did. After then there was a window which showed "updating from current version to version 9.99". I was confused at this point but clicked "continue" and after this stage I got an error message and there was no longer a connection bw my PDA and my computer.
Thanks,
Jonat
Reply With Quote
http://forum.xda-developers.com/showpost.php?p=1784337&postcount=430
Also the same
Problem "lost connection PDA-PC"
Hi,
first I would like to thank you for goooood job to many people here !
Back to my problem. I have HTC Artemis (T-Mobile MDA Compact III), OS WM6 T-Mobile Czech version.
I ran start_uspl.exe on my computer. The part in DOS based screen seems to finish everytime OK, but finally the connection with PC is lost. Therefore when the PDA Phone ROM Update Utility starts cheking version the error "lost connection with PC" appears . PDA stay in "black screen" mode and only hard reset start it again as usual.
Does anybody have the same problem? Any idea, how to solve it ?
Thanks
http://forum.xda-developers.com/showpost.php?p=1773030&postcount=426
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
lenocs said:
then pops to white. I need to do a soft reset to get it running again.
Click to expand...
Click to collapse
What im saying is when it pops to white, dont soft reset it, just start the upgrade.
Anthony2oo5 said:
When the screen goes white, don't restart. Just start flashing to the new ROM. Worked for me
Click to expand...
Click to collapse
that what i also do When the screen goes white, don't restart. Just start your RUU
lenocs said:
Unfortunately it not a white screen, it a black one, connenction lost with the PC, and only the reset PDA helps to restart the unit again....
Click to expand...
Click to collapse
Same situation as above. Depending on the Artemis, the screen might go white or black. Just don't freak out and keep on flashing the USPL. It WILL work and then reboot. Then you can flash the actual ROM you want.
Hello from an absolut newbie trying his first upgrade,
And I have just experienced the same problem than lenocs.
I have run start_uspl.exe, but when the screen is suposed to become white or dark, it becomes dark and the artemis is in fact totally off and connection is lost.
Anyway I supossed that it was because the scrren got black and I tried to run the update utility, but I´ve got an error (the terminal is disconnected or similar) and nothing happens.
I have had to soft reset the terminal and fortunatelly it seems that I still have my previous ROM and it seems that it works. But, do you know if there could be some "side effect" because the first step of start_uspl script?
Anyway I would like to move to WM6, so, any suggestion would be really appreciated.
Thank's a lot
When you restart, what is the USPL number?
Ooopppssss!
I didn't pay attention.
As I've said, I'm a newbie, so I was just woried because I thought I had "bricked" my new atemis.
How can I know now the USPL number?
Anyway I tried the star_uspl again (I'm a crazy newbie) and it failed. The artemis went off almost inmediately.
Thank you very much for your help
SpiggyTopes said:
When you restart, what is the USPL number?
Click to expand...
Click to collapse
solved ... at least for me
I think the problem is in SPL version 3.13 (or maybe anyone newer than 1.11).
Try different Artemis USPL - for me worked version from this page:
http://wiki.xda-developers.com/index.php?pagename=Artemis_DumpedRoms
It's very confusional, because file sizes and also dates are the same as in unfunctional version, but this one worked.
Hope it'll help you as it helped to me.
Maybe this can help you
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Rocheau said:
I bought a 8gb card the week before, so I needed to update the rom in order to have my new SDHC working. But whn I was trying to update the rom, through UPSL 1.1, I had an error. This was the first time I had an error because I have modified the room many times before. My error was about a CMD.EXE issue, something like Error code line 26 "can´t spawn cmd.exe" so I was not able to change my rom. What I did was to copy CMD.EXE from Windows/System32 and put in the same folder where I had the start_uspl file, and finally works!
Do not ask me why, but this was the only way I could make works the update process.
Just try.
Click to expand...
Click to collapse
do u have ur card in the phone while updating
you are suppose to remove the card
Problem solved (for me)
Hi,
i had the same problem error 270, 3% and lost connection with Activesync.
IPL: 3.13.0001
SPL: 3.13.000
GSM: 02.94.90
ROM version: 3.13.405.1.WWE
ROM date: 8/28/07
any way to upgrade was wrong ->> error 270
My good way was:
1. Downgrade to WM5 - original shipped ROM 1.12.405.1(link found on Wiki pages)
2. Under WM5 run USPL to unlock CID (now without any errors)
3. Final STEP - Upgrade to new ROM Artemis Touch 3.01 (without any errors by upgrade)
))
Now my Artemis seems to be OK.
I ran USPL with storage card inside the device...
no problem
switch SD card back to 2GB or smaller before USPL
Hi,
for me USPL did not work with my SDHC 8GB card but then I switched back to my previous 2GB SD card and then it works.
Perhaps the SDHC driver blocks USPL in some way.
Cheers,
Markus
i have been trying for 3 months
once i have upgraded my artemis to wm 6.0 everything seemed to be OK for two days... then the screen started to go black when i restart... şi downgraded to 5.0 but nothing changed... when i remove battery for a while, my arte works... when i try to do anything with it, the screen slowly goes black as if it is broken... please DO HELP ME! i am going to go mad... i have a new iphone, ihave i kaiser as well... but i miss my artemis very much...
Hello:
I have the same problem and realized hundereds have too. I have been checking in all forums and no asolution to it
The issue that happens to me is that I used USPL for upgrading to WM6 and worked, but now for the Touchflo it does not. Tried with all USB ports, tried with different computers and no good news.
The USPL msdos screen indicates that there is no connection at all in all percentage levels, then it bocomes dark and the 260 error whne installing the rom.
please help us soon !!!
we are in trouble!!
Same Problem : Screen shut down
Anybody can help us on this point ?
The only way to solve it is to remove the batterie during 30 min., then put it back and pray...
Then, for no reason, the screen shut down, a few minutes or days after
I've upgrade from WM5 to WM6 with the original Rom of HTC, it seems a little more stable but it shut down every 2 days when i'm lucky
Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725
does anyone know of a company or repair service that will unbrick my hermes?
thanks
Whats wrong, maybe we can help...
Give us a brief rundown on whats wrong, and what you did to fix...
Well first of all,
the phone was bricked through unable to flash a rom
i didn't get a chance to check the SPL and IPL before the phone was bricked
the phone is only showing bootloader and the ok+power+soft reset doesn't work
ive tried the micro sd method and didn't work
i had just barely got the phone and was a noob at it so like every other person who doesn't take the time to read, didn't put the Hard SPL on the device.
i don't know what else to do now.
thanks for replying
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
ultramag69 said:
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
Click to expand...
Click to collapse
dude, thanks a lot!
last time my PPC was stuck at bootloading ( I guess my Hermes 100 can't support M2d due to lack of RAM ). Then I do the step as u mention, n it work!
Thank God. I'm feel relief now, knowing my PPC is revive.
ultramag69 said:
Download the original SHIPPED rom.
Untick "allow usb connection" in activesync on your PC.
Reset into bootloader - hold power, OK button above flywheel and rset with stylus. This should bring you to thr tri-colour screen wher your IPL and SPL are shown. This is true bootloader, not a screwed up version. DO THIS...
Connect Hermes to pc.
Run RUU-Wrapper.exe of original rom.
This may or may not woirk, Good luck...
IF this works, go here - http://forum.xda-developers.com/showthread.php?t=296722
Download Hard SPL V7 & install it. Then you can use sd card method to flash roms, I find it safer...
Cheers...
Click to expand...
Click to collapse
See the problem that i have with that is the fact that i don't know what my original rom was, all i know was that it was an htc windows mobile 5 rom, but i don't know what version..
could it help if i told you that it is a qtek 9600 (herm100)?
Owh, forgot to mention.
I already applied hardSPL. I guess thats why the process of recovering it quite simple. N I directly flash the ROM to WM6.1 v13.3 Cooked Rom. It works like a charm.
Bo0mcxh402 : sorry mate. I didn't know the original version of ur ROM. Maybe u can try to ask around. I'm sure there've lot of users out there also using the same phone as yours,
Try the HTC stock WM06 rom which you should be able to find somewhere on here... May work...
Cheers...
Bo0mcxh402 said:
See the problem that i have with that is the fact that i don't know what my original rom was, all i know was that it was an htc windows mobile 5 rom, but i don't know what version..
could it help if i told you that it is a qtek 9600 (herm100)?
Click to expand...
Click to collapse
It's irrelevant what your original ROM was/is. Follow these directions and use the T-Mobile ROM.
The T-Mobile ROM won't install. It will go thru a couple of steps (one of which is "Erasing" which is critical to get through) and then it will "Error" out. After the T-Mobile ROM "erases", your Hermes should be back to a state where you can flash any ROM you prefer.
Timtown said:
It's irrelevant what your original ROM was/is. Follow these directions and use the T-Mobile ROM.
The T-Mobile ROM won't install. It will go thru a couple of steps (one of which is "Erasing" which is critical to get through) and then it will "Error" out. After the T-Mobile ROM "erases", your Hermes should be back to a state where you can flash any ROM you prefer.
Click to expand...
Click to collapse
Well i Tried the method, but i can't even get the phone to sync even after i unticked the "Allowed USB connections," the phone is recognized as "HTC usb connection" but when i run the t-mobile rom, it says error 264, (USB Connection)
The reason I said to use the shipped rom is because Bo0mcxh402's device ISN'T supercid... If it was it could take ANY rom you want to throw at it BUT because its not you HAVE to have the STOCK CARRIER ROM it was shipped with (later update may work too as the cid should be recognised)...
Cheers...
Bo0mcxh402 said:
Well i Tried the method, but i can't even get the phone to sync even after i unticked the "Allowed USB connections," the phone is recognized as "HTC usb connection" but when i run the t-mobile rom, it says error 264, (USB Connection)
Click to expand...
Click to collapse
Did the T-Mobile ROM do *anything* or just immediately error out?
Timtown said:
Did the T-Mobile ROM do *anything* or just immediately error out?
Click to expand...
Click to collapse
I couldn't do anything because the t-mobile rom didn't recognize my hermes even though my computer did
That pesky CID again as stated so many times before. You need to find your stock carrier rom. The upgrade to WM06 will work as well as it has the same CID as the shipped rom.
ultramag69 said:
That pesky CID again as stated so many times before. You need to find your stock carrier rom. The upgrade to WM06 will work as well as it has the same CID as the shipped rom.
Click to expand...
Click to collapse
well i ended up trying that and nothing happened... the usb connection didn't work for the hermes, i know that there is nothing wrong with the usb connection because i used it on my t-mobile dash.
IVE GIVEN UP.. IS THERE A COMPANY FOR A REASONABLE PRICE THAT WILL UNBRICK THE PHONE?
On the PC - Untick "Allow usb connections" in activesync settings.
On Hermes - Hold OK button, power button and reset with stylus. This will bring you back to bootloader BUT it won't be the screwy bad flash bootloader.
Connect the Hermes to the PC via usb. Run the RUU_Wrapper.exe of the stock rom.
This should work, if it doesn't then there may be no help available. You don't want activesync trying to connect to the Hermes so its better to disable the usb connection settings, You might be able to get a successful flash this way without activesync screwing it up.
Can't say about any unbrick service. Don't think they could help, only thing they might do is replace the mainboard (if they can find) and that would be expensive.
Cheers...
i must admit i am a newbee... i read the thread thoroughly and downloaded the programs necessary to flash my HTC Touch P3452. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM, the version in phone was 2.20.0000 and new is IPL USPL 2.26. then i cliked update and the progress bar appeared on my PC. then after a minute, i gor an error (266) stating that updater cud not connect to the p[hone and asked me to check connection. i didnot do anything. after a while, i noticed a white screen on my phone and progress bar stuck to 0%. now my phone is dead.
can anyone help me
katbasav
Read this http://forum.xda-developers.com/showthread.php?t=406721, something I hope will help you.
Good luck
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
katbasav said:
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
Click to expand...
Click to collapse
tito12 said:
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
Click to expand...
Click to collapse
katbasav said:
the version in phone was 2.20.0000 and new is IPL USPL 2.26.
Click to expand...
Click to collapse
If you are able to enter the bootloader tricolor screen and you see that you have indeed USPL 2.26 installed, then you should be able to flash anything you want!
Fully charge your pda
Remove your memory card and SIM card
Connect via usb, enter bootloader and flash the Rom you want with the RomUpdateUtility.exe
WARNING
Since you don't have HardSPL but USPL be extra careful NOT to flash a Rom that includes SPL cause then your device mightwill get CID locked.
If the above steps don't get you with a working device, then better check if the USPL really worked.
A safe way to find out if your CID unlocking worked is following this method & check the line:
Code:
g_cKeyCardSecurityLevel = ?
;If ?=0 => Touch=CID_Unlocked => Able to flash any ROM or Radio Update through Bootloader
;If ?=FF => Touch=CID_Locked => Try CID_Unlocking again BEFORE flashing anything
Click to expand...
Click to collapse
Regards!
My mobile is HTC Touch P3450. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM & installed its working, but i tried RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe rom but my mobile is showing "smart mobility" and then mobile is off. Pls. kindly help me.
i tried CID unloking also, but not working
Narashimha