I really hope someone can help.
I followed the Hard Spl unlock instructions and all seemed to work well.
I then tried to install the original HTC WWE ROM and it froze at 24% reporting an error. I followed the recovery steps but noticed to my horror that the original SPL -1.25.0000 has reappeared.
I am unable to do anything and have the coloured bootloader screen. Attempts to run the Hard SPL unlock freeze at 0% can anyone help please........
What did you do?
Step by step from the beginning!
Step by step to destruction!
I ran the HardSpl unlock utility as per the detailed instructions. It worked well and I saw the new SPL screen. I unplugged the USB as per the instructions and ran the HTC original ROM Rom updater. All went well until IT REACHED 24% on the screen and on the PC - then it froze.
I waited 30 minutes hoping it would unfreeze but sadly............
I then removed the USB cable and attempted a hard reset. This brought me back to the Bootloader screen with the original SPL displayed.
Further attempts to load the HTC ROM produce an error telling me it cannot be installed on this device. I now have a very expensive paper weight.
Any help much appreciated.
pilib said:
I ran the HardSpl unlock utility as per the detailed instructions. It worked well and I saw the new SPL screen. I unplugged the USB as per the instructions and ran the HTC original ROM Rom updater. All went well until IT REACHED 24% on the screen and on the PC - then it froze.
I waited 30 minutes hoping it would unfreeze but sadly............
I then removed the USB cable and attempted a hard reset. This brought me back to the Bootloader screen with the original SPL displayed.
Further attempts to load the HTC ROM produce an error telling me it cannot be installed on this device. I now have a very expensive paper weight.
Any help much appreciated.
Click to expand...
Click to collapse
Maybe here was the problem...
If you have hard-spl on your machine (in bootloader you see Olinex) after you do not have to replug the usb cable.
Just run the romupdateutility.
Now it seems you have original spl...
In this case you can not install not offical rom. You sould try the offical Orbit 2 rom.
I THINK U HAVE TO TRY HARD-SPL, are u shure u,ve done allready?
Resurrection!
In desperation and believing I had nothing to lose I attempted to flash an O2 Artemis
ROM to the Polaris. It got to 2% failed but rebooted the device to the original ROM.
I had previously tried hard and soft restes and could get no further than bootloader screen.
I don't know or understand what happened but my phone is alive again.
I would wan anybody abut the Hard Spl Unlock.....it caused me major hasslr.
Thanks to those who tried to help me.
clearly you didn't get Hard-SPL, you got the soft-spl
congratulations for your massive fail.
Olipro said:
clearly you didn't get Hard-SPL, you got the soft-spl
congratulations for your massive fail.
Click to expand...
Click to collapse
^ Lol, he's the guy who came up with the Hard-SPL, so as you can imagine he's a little pissed off about the criticism.
Confusion
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
pilib said:
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
Click to expand...
Click to collapse
No, it not is the problem of hard-spl.
You did something wrong, according to your step by step guide.
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX.
On the pc run the RomUpdateUtiliy (from the offical rom folder)
After Few minutes pda will reboot, new rom is installed.
Anybody succewssfully changed XDA Orbit 2 ROM?
Could I ask if anybody has succeeded in changing the XDA Orbit 2 ROM for an alternative and if so could you outline the procedure. Many thanks
pilib said:
Could I ask if anybody has succeeded in changing the XDA Orbit 2 ROM for an alternative and if so could you outline the procedure. Many thanks
Click to expand...
Click to collapse
Read the post just above yours.
Sascha
Clarification
I am looking for someone who has actually succeeded - not just the theory!
Here are some:
http://forum.xda-developers.com/showthread.php?t=372665&page=2
Success
I must eat humble pie - it obviosuly was due to some error on my part that the ROM replacement failed. I have now been successful. The Hard Spl unlock works perfectly, and I will send a payment to show my gratitude!
pilib said:
Thw file that I downloaded and used was "Hard-Spl-V2" This is what caused the problem.
Click to expand...
Click to collapse
the problem was you ran the htc ruu after replugging usb in the hardspl unlocker process
edit: sorry i see problem has been solved
cmonex said:
the problem was you ran the htc ruu after replugging usb in the hardspl unlocker process
edit: sorry i see problem has been solved
Click to expand...
Click to collapse
yeah thats what i also think. he didn't compleate Hard-SPL process, when asked for re-plug just ran RUU.
Related
Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.
If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.
g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.
Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.
Thanks for details...
Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2
Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.
shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?
The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .
Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !
Ignore this post - I had IE troubles and double posted - See next post
Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434
Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem
Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.
See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.
For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.
See this thread..
http://forum.xda-developers.com/showthread.php?t=373725
Hi,
Does anyone know how can I restore the original SPL from bootloader ? I try to do it, the progress bar goes to 100% but when I restart it, I still have the HardSPL installed.
Any ideas ?
Use SEARCH please
ygeordy said:
Hi,
Does anyone know how can I restore the original SPL from bootloader ? I try to do it, the progress bar goes to 100% but when I restart it, I still have the HardSPL installed.
Any ideas ?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=381600
second post
Thanks for the reply.
I tried that. Unfortunatelly it doesn't work for me. The progress bar goes to 100% and after restart I still have OliNex loader. I don't have the step which says "Unplug cable".
Some other ideas maybe ?
ygeordy said:
Thanks for the reply.
I tried that. Unfortunatelly it doesn't work for me. The progress bar goes to 100% and after restart I still have OliNex loader. I don't have the step which says "Unplug cable".
Some other ideas maybe ?
Click to expand...
Click to collapse
That message appears on the device (on the colored bars screen). Maybe you thought it should appear in Windows.
It worked for me
SuperJMN said:
That message appears on the device (on the colored bars screen). Maybe you thought it should appear in Windows.
It worked for me
Click to expand...
Click to collapse
I know it's on the device. It did, when I did the hard spl. Now when I'm trying to get back to original spl (device stucked in windows boot screen) I don't have that message, but the process goes through. Unfortunately without any result.
ygeordy said:
I know it's on the device. It did, when I did the hard spl. Now when I'm trying to get back to original spl (device stucked in windows boot screen) I don't have that message, but the process goes through. Unfortunately without any result.
Click to expand...
Click to collapse
Stucked windows screen is a different problem. This method is ok only for working device.
In this case this is the only one idea:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
fktsndr said:
Stucked windows screen is a different problem. This method is ok only for working device.
In this case this is the only one idea:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
Click to expand...
Click to collapse
yeah, tried this already also. after I hit task 8 and enter, the device resets, goes to Windows startup screen, get stucked again and just turns off.
Full description off my problem here for whoever wants to help me.
http://forum.xda-developers.com/showpost.php?p=2126848&postcount=31
I fully appreciate any kind of help.
Did you try flash back the original rom?
And I suggest rename this thread for example Stucked in windows screen...
Maybe more people will read it, and try to help you....
fktsndr said:
Did you try flash back the original rom?
And I suggest rename this thread for example Stucked in windows screen...
Maybe more people will read it, and try to help you....
Click to expand...
Click to collapse
I did try to put back a french ROM. I don't know if it was the original because unfortunately when I first flashed it I was kind of beginner in flashing HTC's, but I tried with the only original french ROM that I found on this forum. The process goes through, but yet the result is the same. Is there any kind of command to fully erase (format) the memory (beside the bootloader) and then try to load a ROM ?
Same for me with restoring SPL ...it doesn't work.
And my device is almost at the same state of damage as yours. See my thread...
http://forum.xda-developers.com/showthread.php?t=402765
Also the mtty and task8 just restarts my device. Nothing more, nothing less!
So there is no way of restoring SPL with entering the bootloader manually? Not even a mSD-Card Trick out there? I need to get it done because of warranty ;/
You stucked in Olipro hard-spl, this is why restore spl not works...
And unfortunatelly you can not flash spl with micros-sd.
But you can try to flash rom with micro-sd card.
http://forum.xda-developers.com/showthread.php?t=384084&highlight=guide
Or ask Olipro, maybe he can help you.
Well I am able to flash my Rom the usual way with USB connection.
But no way of restoring the SPL ;(
"So there is no way of restoring SPL with entering the bootloader manually? Not even a mSD-Card Trick out there? I need to get it done because of warranty ;/"
I do not understand exactly...
Did you try restore original spl with manual bootloader?
you run SSPL from Windows Mobile, then flash a stock SPL NBH, job done.
the whole *point* of Hard-SPL is that it can't be overwritten when it performs a flash so that if anything screws up you don't end up locked out of reflashing in the event something screws up.
Olipro said:
you run SSPL from Windows Mobile, then flash a stock SPL NBH, job done.
Click to expand...
Click to collapse
Sounds easy *hehe* BUT i can't access Windows Mobile anymore, that is my big problem. So my device will be picked up by O² in a few days, so i have to get the original SPL back without accessing Windows Mobile ;(
Any suggestion?
@fktsndr: no, thats why i have put a question mark behind it I just need a way of downgrading to the Original SPL without access to Windows Mobile. Maybe i should be sorry for my english
gmc said:
@fktsndr: no, thats why i have put a question mark behind it I just need a way of downgrading to the Original SPL without access to Windows Mobile. Maybe i should be sorry for my english
Click to expand...
Click to collapse
So...
You have hard-spl on your machine
You can not restore spl followed the guide in post 2 (WITHOUT manual bootloader)
You can not access your windows mobile (WM does not boot)
You freeze on startup screen
You can not start you phone with steps in post 6
Am I right?
If yes, you stucked in bootloader. And unfortunatelly I can not help you...Maybe Olipro.
fktsndr said:
So...
You have hard-spl on your machine
You can not restore spl followed the guide in post 2 (WITHOUT manual bootloader)
You can not access your windows mobile (WM does not boot)
You freeze on startup screen
You can not start you phone with steps in post 6
Am I right?
If yes, you stucked in bootloader. And unfortunatelly I can not help you...Maybe Olipro.
Click to expand...
Click to collapse
Well seems like something like this.
See I have no error because of invalid flashing. I had slight water damage. But some days later my device was working again for a whole day.
Next day it didn't work anymore.
When i startup my device and the WM-Splash shows up it makes "bring" and device turns off.
When i plug in the AC charger i can't even get beyond the O2-Splash.
But I can enter the bootloader and flash what I want, it works ;/
I am also able to connect with MTTY, maybe there is a way with repairing it through MTTY?
Full description of my problems here: http://forum.xda-developers.com/showthread.php?t=402765
But if i cant get rid of the problems i have to send it to warranty by tomorrow or monday and i think they will notice that i don't have the original SPL on it. So they will screw me ;(((
So, as I am not a noob to computers I would try ANYTHING to get it back on my own!
Is there also no way of restoring it by using the microSD-Card? So is there no way without Windows Mobile? Not even the holy MTTY? Or any way of debugging it by MTTY to see whats going wrong?
I'm screwed!
P.s. I have also tried another battery in the o² shop....didn't fix it ;(
gmc said:
Well seems like something like this.
See I have no error because of invalid flashing. I had slight water damage. But some days later my device was working again for a whole day.
Next day it didn't work anymore.
When i startup my device and the WM-Splash shows up it makes "bring" and device turns off.
When i plug in the AC charger i can't even get beyond the O2-Splash.
But I can enter the bootloader and flash what I want, it works ;/
I am also able to connect with MTTY, maybe there is a way with repairing it through MTTY?
Full description of my problems here: http://forum.xda-developers.com/showthread.php?t=402765
But if i cant get rid of the problems i have to send it in by tomorrow or monday and i think they will notice that i don't have the original SPL on it. So they will screw me ;(((
Is there also now way of restoring it by using the microSD-Card? So is there no way without Windows Mobile? Not even the holy MTTY? Then i'm really f***ed.
P.s. I have also tried another battery in the o² shop....didn't fix it ;(
Click to expand...
Click to collapse
There is an mtty method on post 6...maybe helps start your phone...
You need working windows mobile to restore-spl.
fktsndr said:
There is an mtty method on post 6...maybe helps start your phone...
You need working windows mobile to restore-spl.
Click to expand...
Click to collapse
Yes but on "task 8" my device doesn't behave as it should be. It just restarts doing nothing.
Seems like i just have to hope the guys at the service center will not recognize my "not original" SPL. 1% chance ;(
Well thanks for now fktsndr.
Seems like there is really no way of restoring it without Windows Mobile ;(
I thought there would maybe be a "Low Level"-Method of accessing the device and restoring SPL.
Can't think of that there is no way of formatting the device on its lowest level (mtty) or transferring the original SPL per MTTY. Hmm...there should always be a way
Olipro, no way? ;(
if I remember right, the polaris hardSPL is based on an MFG bootloader.
this means you can use mtty commands (mw) to unpatch the write protection then flash the stock SPL.
if I don't remember right, and it is not MFG, then you can still use another mtty command with a special file, but this is more complicated and was not fully tested. you can contact me in PM and we can see.
(you could transfer SPL via mtty, but that is also blocked in hardspl because the mtty transfer uses same code to flash the SPL in this SPL common base)
by the way task 8 is exactly designed to just do a soft reset. nothing wrong with that command.
they really meant task 28. this does a hard reset. you can try that. I guess you already did, but just in case!
edit: I just remembered another way if task 28 doesn't help. ifyou don't mind that the device will stop booting SPL, then you can just do task 2a command in mtty. this will erase SPL, and because of hardSPL overwrite protection it will fail to flash it back from the temporary RAM backup.
the result is that the device will not even boot SPL, it will be black screen. it will boot to the radio bootloader only and O2 won't know what SPL was on it before erase.
I'm new in these forums as well I'm new with flashing ROMs so obviously I messed up flash process and my device stuck in bootloader (tri-color) mode. This post I address to those unfortunate like me .
# Symptoms #
- ROM flash started and stopped at 17%. After recovery flash process stucks at 0% and pops Connection Error 262. Device is stuck in bootloader mode not possible to flash anything, hard reset does not help, flash from SD card does not help either.
# Possible cause for that #
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
2. Connection between ActiveSync and device was not established when flashing ROM file.
Before to go any further please take your time and read Polaris Wiki to get familiar with glossary and acronyms used here.
PROCEED ONLY if flashing original ROM does not help, hard reset does not help and flash from SD card does not work.
# Solution #
1. Download MTTY software.
2. Kill ActiveSync (Press Ctrl-Alt-Del and stop rapimgr.exe and wcescomm.exe processes).
3. Plug Polaris into usb port (Plug directly not through hubs).
4. Start MTTY after chose USB from PORT dropdown list (if it is not listed there then ActiveSync processes were not stopped).
5. in window type: set 16 0 (enter cmd mode)
6. after type: task 8 (this will format phone)
7. after type: task 0 (this will restart phone. Not always necessary)
8. soft reset
This procedure can damage your phone. Use it as last resort.
Official source in french here.
Now before flashing any ROMs read carefully how to flash (not install!) Hard SPL.
# P.S. about install and flash termins #
This error with flashing happened to my due misunderstanding between notions of installing something on your device and flashing. In my opinion those are completely two different things. As for first I understand of running some cab or exe directly on device. So problem comes when people sees install Hard SPL en device as they try to find some cabs or exes to install directly on device or they just copy all files to device. To make things clear Hard SPL "installation" actually is ROM flash process which must be done with maximum caution, but those who did not read Wiki won't understand it.
Cheers, whitealien
BiG THX @ Whitealien.
works to 100% on my Touch Cruise.
I flashed under Vista Ultimate...
# Solution # ... addition from me for Vista users!
....
2. Start Windows Mobile Device Center and Deaktivate USB Connection and then start Task manager end kill
Process wmdc.exe.
Rest of whitealien. and have fun!
Thank you!!!!
I had given up on this, and was sure my only option was a warranty repair :O
always welcome
Thanks, you've saved my Polaris.
Mine didn't want to react anymore to the soft reset, so I replaced your instruction 8 with:
Cmd>boot
and that did the trick.
whitealien said:
1. In bootloader mode device shows:
Code:
Pola100
SPL-1.25.0000
CPLD-2
means that Hard SPL was not flashed before flashing ROM file (if Hard SPL was flashed then in second line will be written SPL-2.20.Olinex.).
Cheers, whitealien
Click to expand...
Click to collapse
I had exactly the same problem, for whatever reason went back to original SPL before HARD SPL.
I solved my issue by using back the original original HTC RUU_signed.nbh and flash it using the CustomRUU.
Thereafter, repeat the entire HARD SPL and flash the home cooked ROM.
Cheers.
For unbricking your HTC Polaris, you can try also a hard-reset (if it is related to a software error):
http://www.hardreset.eu/htc_touch_cruise_polaris_hard_reset_soft_reset.html
Thank you very much
you really helped
thank you again
mrfone2003 said:
Thank you very much
you really helped
thank you again
Click to expand...
Click to collapse
you are welcome.
Seems people are still falling for this error.
I'm has this error.
Solution (with SPL-2.20):
- kill ActiveSync (process, not uninstall)
- cable to USB on motherboard
- hard reset on phone
- connect to cable
- flash OFFICIAL rom
Two time I revive my Polaris.
help me please
hi.I have a big problem with my htc touch cruise when I installed a hard spl htc dedicate a Diamond.donc I had a white encrant after I did a hard reset since my htc no longer I have a black encrant are neither green nor orange but when I connect with the pc I am data interface and it does not recognized my htc. In my pay is not qualified repairman three non réparé.aidé unable to please me I tried the commands mtty.exe but does not c I do not really know how it works.
thank you for your patience and for help
thanks for the support
Thanks dudes for the great help you gave to recover my htc dual from bootloader screen. I am very happy to have my phone back. Thanks for everybody for the help they have provided generously. I appreciate alot. infact thousands times.
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
aaront1988 said:
I think i have really messed up my phone. When opening mtty i select USB and press ok, then it says "can not open USB Port"
please help me, i have all the symptoms you explain. Stuck in bootloader, POLA200 SPL-1.25.0000 CPLD-2
i cant flash any roms and the original rom stops at 39%, i have redownloaded it countless times so its not the rom.
Click to expand...
Click to collapse
Did you follow all steps from 1st post?
Did you kill all running ActiveSync processes?
I did indeed, i'm on vista so didnt have those particular processes going but followed the step from Aeroman and it still doesn't want to play. Any ideas?
managed to find a working XP machine and it worked a treat. Thank you so much.
thanks,this solved my pb
please help
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
wesram said:
Im having the same problem, im stuck in the bootloader but i didnt do anything for that to happen....this happened all alone withount any try to flash or do anything
it is saying
POLA100
SPL-1.28.0000
CPLD-2
when this happened i tried sodt reset and unpluging the battery b4 reading and searching here.
now i tried the steps showing in the first post and step by step .... the devise restart to the same bootloader like i did nothing ((( oh god im so upset please help me .... what to do ((((
Click to expand...
Click to collapse
What did you do to get there?
whitealien said:
What did you do to get there?
Click to expand...
Click to collapse
hey, im sorry for the late reply. it didnt notify me and now after posting several times asking for help in many threads by accident i bumped into this thread again to see that u answered and thank you so much.
now, what i did? this is the wierd thing, i didnt do anything, i went and back to see my phone stuck in bootload .... after this i tried almost everything i can find. from ur solution to flashing original rom to hrd spl to .........
now all gave an error except the original rom (polaris.1.28.415.2), it did went to 100% and device restarted to take me to my nightmare .... another bootloader screen am i suppose to search for polaris 1.28.0000?
i still have now the same writing shown.
please help me with this, its a nightmare .... is it totaly dead???
i managed to catch what it is saying b4 bootload screen (only when SD card is in place) it says no image file was found!!! in a very fast way and go to bootloader. in case the sd is not in place nothing happens and it goes straight to the bootloader
i must admit i am a newbee... i read the thread thoroughly and downloaded the programs necessary to flash my HTC Touch P3452. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM, the version in phone was 2.20.0000 and new is IPL USPL 2.26. then i cliked update and the progress bar appeared on my PC. then after a minute, i gor an error (266) stating that updater cud not connect to the p[hone and asked me to check connection. i didnot do anything. after a while, i noticed a white screen on my phone and progress bar stuck to 0%. now my phone is dead.
can anyone help me
katbasav
Read this http://forum.xda-developers.com/showthread.php?t=406721, something I hope will help you.
Good luck
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
katbasav said:
thanks.. but did not help me... i tried as per the sticky given in begenning. nothing worked..
Click to expand...
Click to collapse
tito12 said:
I doubt that you tried all the possibilities mentioned in post 7 from the link I gave you before, but if you did and nothing worked then I can't see what will...Sorry mate but before you call it dead, try a 2nd time and 3rd,
Good luck.
Click to expand...
Click to collapse
katbasav said:
the version in phone was 2.20.0000 and new is IPL USPL 2.26.
Click to expand...
Click to collapse
If you are able to enter the bootloader tricolor screen and you see that you have indeed USPL 2.26 installed, then you should be able to flash anything you want!
Fully charge your pda
Remove your memory card and SIM card
Connect via usb, enter bootloader and flash the Rom you want with the RomUpdateUtility.exe
WARNING
Since you don't have HardSPL but USPL be extra careful NOT to flash a Rom that includes SPL cause then your device mightwill get CID locked.
If the above steps don't get you with a working device, then better check if the USPL really worked.
A safe way to find out if your CID unlocking worked is following this method & check the line:
Code:
g_cKeyCardSecurityLevel = ?
;If ?=0 => Touch=CID_Unlocked => Able to flash any ROM or Radio Update through Bootloader
;If ?=FF => Touch=CID_Locked => Try CID_Unlocking again BEFORE flashing anything
Click to expand...
Click to collapse
Regards!
My mobile is HTC Touch P3450. I downloaded Onyx Ultimate and unzipped. connected my phone to activesync and ran the RUU. I followed the steps and till i reached update ROM & installed its working, but i tried RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe rom but my mobile is showing "smart mobility" and then mobile is off. Pls. kindly help me.
i tried CID unloking also, but not working
Narashimha