My heads spinning from all the information aka post and threads, but im still stuck like my wizard on the 2nd splash screen.
I wasnt trying to upgrade the rom jst clear storage but after everything ive read i would like to upgrade to wm6 but first i want to get my wizard working.
I tried backing up the rom to the sd card but I get "You didn't get the proper security level to download a specific image" So i take it my wizard is cid locked.
My IPL:1.01 and SPL:1.06 does that mean its a g3. My activesync 4.5 doesnt pick up my wizard is it because it cant boot, i tried with it in bootloader mode still doesnt pick it up.
So plz point me in the right direction to fix my wizard
ok i think the place where im stuck at is cid unlocking my wizard with out using that imei site. any help or is there another way to do this.
This helped me when I was stuck on the first screen. For some reason, the Radio file was gone. Follow this exactly, it works. In my case (sounds like yours also), at the end of this you will at least have access to the phone again.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=bootloader
After your done. You will have a RGB screen, then follow these directions to load a base rom and unlock so you can keep going until you ca load WM6.1.
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I've had many, many problems over the last 3 days trying to do this. I completed it all in less than a day, but when I used the phone it had terrible reception. I completely downgraded everything back to square one. Still bad phone reception. I was about to through it out the window, when someone called my wife's cell phone and she also had bad reception. I then put my sim in another phone, same problem. Well, at&t has a tower down for the last 3 days. What timing, it seems to work when not at home, but hard to test that way Anyway, moral of the story is. Don't give up, keep plugging along.
Good luck.
I'm pretty sure imei checker is for SIM unlocking.
For G3 CID unlocking and upgrading read the stickies in http://forum.xda-developers.com/forumdisplay.php?f=289
If you can start your Wizard in bootloader, and it says "usb" in the lower-left, you can flash your original ROM. An active sync connection is not needed. Search for your carrier's ROM if you don't have it and I'd recommend the "no carrier ID" version of the RUU.
Have you tried a 'Hard Reset',hope it'll work,if it boots up into working OS and it already has IPL/SPL 1.xx,use lokiwiz02b tool to SIM/CID unlock the phone and than upgrade.
If it doesn't work still after Hard Reset,most probably,its Extended_Rom is corrupted,its required to reflash a new rom.
Activesync doesn't work in absence of a working OS and in Bootloaders mode.Its not required for flashing a rom.Just get the phone into Bootloaders and hook the phone with pc via usb cable and watch small usb appear at the bottom of the bootloader screen,if its there,it good to go and flash the rom.
ok so i downloaded the button rom finally but how do i flash it to my wizard.
Get your phone in Bootloaders,hook up the phone with pc via usb,watch small usb appear at the bottom of the Bootloader screen,if its there run the 'RUU' application,it'll start to flash,it stops at a certain percentage,don't get worried and do anything,after a couple of minutes it starts again,let it complete 100%,the phone'll restart and boot up in new OS.
which ruu application. I jst downloaded 1 which comes in the form of a rar file saying ruuwrapper. is that the right 1
So after lots and lots and lots more reading i realized i dont need a ruu. all i need to do is get into bootloader mode plug in the usb and run the wizard button rom. It worked perfectly my wizard is back to life yip pee.
Anyway i wud jst like to thank u guys for all the help and compliment u guys on a gr8 forum.
Now my next challenge is wm6 with touch flo.
Related
Ok,
So I installed the T-mobile UK radio rom on my unlocked cingular HTC 8125 with a t-mobile sim. Upon reboot I get no phone service, it acts as though the phone is shut off but it's not. On bootup when it displays the IPL/SPL and OS and all that there was a line between the IPL / SPL lines and the OS line which used to have something on it, but now it's blank. Here's the worst part, it no longer recognizes on USB or under activesync, I tried to get it to work with bluetooth using a usb bluetooth adapter, but to no avail.
I need to know if there is anyway to get it working again, anyway at all to get it to connect or something so I can install a new radio rom on it.
Please help.
Help me too
I am in exactly the same predicament. I have spent days searching for a solution. Nthing so far. Anyone?
Rogue23
Well,only flashing a Radio Rom,never bricks a phone,cuz it doesn't include any IPL/SPL in it Its just a bad flash.Either,Try a Soft Reset or Hard Reset,if works fine,otherwise,get the phone in bootloaders (multicolor screen) and flash the cingular official Rom,it'll recover back. The phone doesn't get detected via usb or doesn't activesync if there's no working Rom (OS) on it,but if you are able to get to bootloaders and connect the phone via usb cable, a small usb appears at the bottom of the bootloaders screen,it means it has established connectivity and you can flash a rom.
Secondly if the ohine is not SIM unlocked,it won't work with a T-mobile SIM,you'll have to get it sim unlocked if you plan to use a different sim and network.
ericmda
Be a little more specific about the problem and remember to always post the version of the phone OR vital data of the phone to ask for an advise.
Cheers!
been done
yeah,
I've been able to get it into bootloaders, the usb pops up in the corner but when I try to flash a rom it it gives me a no phone connected type of error. which is really messed up because the first time I put it into bootloaders it worked, but I didn't use the official rom so the flashing didn't fix it.
If flashing the radio rom isn't supposed to brick it then well somehow mine is apparently the exception to the rule. Still gonna be working on it throughout today though, so any other suggestions?
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Zulu137 said:
I have a Cingular 8525 running WM5 that is stuck in bootloader screen. I have tried to soft and hard reset ... just boots back to the same screen, I can't turn it off once in the screen and when i sync via usb to the pc i get the message that the "usb device that is connected is malfunctioning" I have not done any upgrading at all and the phone worked perfectly right up till the time i powered it down and restarted into the bootloader screen.
Please can someone out there help me with this issue?
Click to expand...
Click to collapse
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Asfarizal said:
same problems, run perfect before with schaps wm6 rom then flash to faria wm6.1... not feel good with faria. try to flash with other rom then the problem start ..
how to recover ....... please help
Click to expand...
Click to collapse
Manage to solve the problem ...thanks WIKI !!
Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus
Then Flash to any ROM you want !!
Thanks .... But
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Thank You
I will follow the instructions you gave and try to get it going this weekend.
Thank you so much for your time
Zulu137 said:
Thanks for the reply ... but i have no idea how to do what you tell me, I am new to all this phone "stuff" as a matter of fact this is the first time that i am ever using one of these forums. I have read till i am cross eyed but dont actually understand what you are talking about ... now don't let that scare you away as i am willing to learn and i am not braindead ... you all had to start sometime in this, not so. I get that i need to try and reflash my rom...
so is there some type of rom update software that i need? ... what is a hard SPL?? ... and who is Schaps?? .. sorry guys to do this to you but i would like to get into this game and i need some ( well maybe a lot ) of pointers.
Thanks for your time.
Click to expand...
Click to collapse
Looks like you've got a lot of reading to do, and a problem to sort out. Firstly a couple of answers...
Schaps is a Rom Cooking guru (makes custom versions of WM5, WM6 etc). When you get your phone sorted out I'd recommend trying one of his roms.
Hard SPL. The SPL is part of the bootloader which effectively dictates how a rom is flashed and what roms can be flashed. HardSPL is a custom version of this which allows you to flash any rom from any carrier. It also protects against a bad flash in many cases. It is recommended before you try flashing any new roms or radio roms. Use Hard-SPL-V7 at the bottom of the first post here.
The Rom upgrading software is contained in any of the cooked or carrier supplied roms. It is normally a .zip file which cotains 2 files: xxxxxRUU.exe and RUU_signed.nbh. You run the .exe file from your PC when connected to your phone via USB. More details of how to do this are in MrVanx's guides. Also other resources here.
Now to try to sort your phone out...
What is displayed on your screen when in bootloader mode? It should be something like this:
HERM200
IPL-1.04
HERM200
SPL-2.10.Olipro (This is HardSPL V7)
If you don't have an Olipro SPL then you need to get HardSPL onto your phone. If you haven't done any upgrading and have had the phone from new then I guess you don't have hardSPL.
Now you need to fix your USB Malfunctioning problem. I can't help too much here except to suggest trying a different cable, different USB port or different PC. Also, if you are running Vista try an XP maxhine. When you connect to the PC does your phone show Serial or USB on the screen? If you can't get a USB connection, all is not lost - you can re-flash your rom using an SD card, method here.
There is a thread about un-bricking phones which may help.
There are various diagnostic tools (which can also screw your phone if used incorrectly). The favourite of these is MTTY but you need a USB connection to use this.
If your phone is in warranty I'd recommend getting your supplier to sort it out, but if not I'd try to re-flash an ORIGINAL supplier rom (Cingular I guess). You can get links to the official supplier roms here.
I think (might be wrong) that sometimes when stuck in bootloader you need to flash an official rom, not a cooked one to recover your phone - then you can run HardSPL and then flash cooked roms again.
Cingular 8525 stuck in bootloader
Thanks for the reply ... lots of great input.
Now to answer some of your questions.
1) When I power up the phone (only pushing the power button ) it goes straight into the bootloader screen without pushing any other buttons, and it displays
HERM100
IPL-1.01
HERM100
SPL-1.06
Then at the bottom in the white bar it says "Serial"
The only way that i have found to power it down again is to remove the battery, there is no response from any single buttons after it is in bootloader
the soft reset and hard reset work but it just goes right back to the bootloader screen after.
2) The USB malfunction. This only started after the phone "crashed" and before that it worked great ... well i only used it to sync up to my work pc for the contacts and to get pictures onto my hard drive.
all the PC's that i use are running XP. I have tried my home PC and my Laptop
and the work PC and all of them have their own cables and they all say the same thing ... "the USB device is malfunctioning"
I am sure that when i get the phone going again the USB will start to function again.
3) Phone warranty ... I bought the phone off e-bay from a store in new york about 10 months ago as a "new unlocked cingular 8525" it was new and unlocked, but i have no idea how they unlocked it. I would assume that there would be no warranty now and in any case i live in Canada and would have to ship it down to the states to an AT&T repair center and that sounds like a nightmare to me with the customs and so on.
I will give you a little more background on the problem. the phone worked like a charm without any problems at all for the 10 months that i had it, then the morning of the crash the phones alarm did not go off in the morning and i was almost late for work ... i did not pay it any further attention untill at 3:26pm
that afternoon the alarm went off ??????? (it was set for 6:05am) so i checked the main clock time, it was right. I then checked the alarm time, it was right ??? So i figured that something must have just got confused, so i powered down the phone with the power button to just restart it and while it was powered down i removed the battery to take the oportunity to to clean all those fuzzies and dust that collect in the battery compartment out and put it all together and powered it up again (just by pushing the power button) and this wierd red, green, blue and white screen appeared and that is all that i have seen since ???
I hope that answers your questions and i will start going through the links that you sent and get to reading ... will there be a pop quiz ... lol
Thanks again for your time and i very much appreciate all the time that all of you have spent on me and my phone ..... I know that you all just feel bad for me because i now have to use a Motorolla V551 ... lol
Great Work
ultramag69 said:
1. Search for "mr vanxs guide" so you have an idea on what you're doing.
2. OK, as Asfarizal said "Go to Bootloader mode: Hold side OK and POWER buttons together and reset with stylus". If you cant work out what the buttons are, go to the manual. it will tell you.
3. type in "hard SPL" in search on the forum & download the .zip or .rar file. this should have 2 files inside when opened,
a). RUUWrapper.exe and
b). RUU_signed.nbh
sync Hermes and double click .exe file. follow prompts.
4. find a rom that you want (would suggest TNT SE as a fairly good rom for noobs... good and stable, no problems...) Again download, then (and this is personel preference) format an sd card fat 32 and copy RUU_signed.nbh into root directory. Rename it Hermimg.nbh. Put into Phone and put into bootloader(make sure the battery is more than 50%) follow prompts. This should get you out of trouble. You can also sync your Phone and double click on the RUUWrapper.exe HOWEVER, if you should reset your computer, pull out the usb cable or have anything else happen to the computer that interrupts the flashm, you could end up with a worse brick than you have now. try to read up on flashing (search for "mr vanxs guide") and this should help you a lot if you have other questions. Good luck and happy flashing......
Click to expand...
Click to collapse
Thanks a lot man & great work i unbricked my Herm100 with method u mention above thanks a lot & great job keep it up
I also have this problem.
I d/l Hard-SPL-V7
and when i run RUUWrapper.exe
I get an error saying the application failed to initialize properly (0xc0000135)
What's going on?
How do i fix this?
this happened when i was trying to unlock the phone.
Thanks
need help
when i switch on my orange herm100 it shows On the bootloader screen is displayed:
HERM100
I PL-1.01
HERM100
SPL-1.40.01ipro
history : i buy unlocked orange phone
fewdays back i found no imei ,
yesterday i try to flash by micro sd but in gsm stage its gets hang no progress after extrom stage
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM - (NO ACTION)
OS -
i tryed several time no action, i cant connect by mini usb.
PLEASE help me
tell me which it the right rom to chose? step by step procedure..
how to rectify imei?
thanks and regards
kirtibas
kirtibas, sorry it took so long to reply, 1st thing I'd do is upgrade to SPL 2.10 olipro. This is safer to use than others. then I'd suggest reflashing a stock rom to see if that works. After stock rom works then use a cooked rom as your heart desires... Cheers...
I unlocked a Cingular 8125 and went to load TNT Professional ROM. The phone kept losing communication at 99% and when I went to reload the original ROM from HTC's site, now I have NO O/S. I DO have another one, but my wife is using it until we get her a pink BlackJackII. I really like these phones, and can't believe I crashed this one! I don't have any Mini-SD cards. Any way to rebuild this thing?
Nobody has any ideas for me? I really need to get this phone running again!
Your not using Vista are you?
Most comm errors are due to weak or discharged battery,not having enough juice to complete the the flash,get it fully charged and try again,secondly,Yes! don't use winVista.
Download the official stock rom and flash to recover back.Get the phone in Bootloaders (RGB screen) hook up the phone and watch small usb appear at the bottom of the Bootloaders,if its there,run the rom to flash,it'll start to flash,but if small usb is not present than most probably its a comm fault.
I was using a Win2K machine. I had 2 batteries that were fully charged. I have a friend that will lend me his miniSD adapter and use my 1gig microSD card to get the info off my wife's phone and copy it to this one. He has a Sprint version of the AT&T Tilt. Might see if he wants to check out this site.
OK. I have access to a miniSD card now. Do I just take my wife's 8125, make a backup from it, then put the card in the bricked phone and load bootloader?
Read this thread for more specific instructions :-
http://forum.xda-developers.com/showthread.php?t=276963
But this method will only work if both the devices are already CID unlocked.Secondly,most important,both the devices shud be of same DOC Chip version,G3 or G4.If you back up a rom of G3 on a G4 device,it'll brick it and vice versa,make sure both the devices are of same DOC Chip version.
They are both G3's. I think they may even be from the same batch. If I unlock hers, won't I lose all her data?
YUP ! but first make a back up of all the personal data on her phone to your pc,for this use either 'PimBackup' or any similar back up application and than unlock it.Its necessary to have both phones CID unlock,otherwise,this method won't work.
OK, I used Lokiwiz 3beta and superCID unlocked the other one. When I run mtty, and use the r2sd all command, I get
R2SDBackup()-Download type=5
usTotalBlock= 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
I have left it sitting there for an hour and nothing else happens. Isn't it supposed to have several more lines of text scroll by? Also, I can't figure out how to get the dead one to boot to the miniSD.
ok,did you read the method carefully,the link I posted above ? you are getting it correctly.
This methods involves many steps.
Step 1.
Back up all the data on your wife's phone to your pc with 'PIMbackup',than downgrade to IPL/SPL 1.xx either through flashing 'Button's Rom 1.05 or you can even flash official stock rom Aku1 for this,when getting IPL/SPL 1.xx either way,apply lokiwiz02b and not lokiwiz 3beta to CID unlock your wife's phone,or you can use WST_4.2.2 tool also to CID unlock it,but its must to have IPL/SPL 1.xx to CID unlock in both the ways.Only after getting the phone CID unlocked,you can Backup the rom on a miniSD card.
Step 2.
After successfully back up of the rom on miniSD card,insert this card in your dead phone and get the phone into Bootloaders mode (RGB screen).
Step 3.
Run the MTTY command to back up from miniSD card.This is only possible if you already have this phone CID unlocked,otherwise it won't work.
Both the devices must be CID unlocked.
Although,I'm still not sure if it works,but there's no harm to try,may be it gets going.
Is the progress bar supposed to change back and forth from blue-green to red while flashing?
YUP ! it changes during flash,but it'll become green on 100% completion and the phone reboots.
OK. I can't get this thing to take the WizardLove ROM, can't find Button's ROM, but I am trying to load the XDAMiniS ROM now. On my third try and the SPL still says 2.25. Battery is fully charged and I get an immediate connection failure trying to load WizardLove. I really wish I could find the original Cingular ROM for this phone, not the new(er) update.
Download Cigular official stock rom from here :-
http://www.htcamerica.net/support/8125/software-downloads.html
or
http://download.america.htc.com/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe
Check out this link for all the Roms like Buttons Rom T-mobile 2.26 etc
http://wiki.xda-developers.com/index.php?pagename=Wizard Windows Mobile 6 for newbies
I am just about ready to give up on this thing. No matter what I do, when I try to boot it up regular, it still keeps freezing up and when I try to do a hard reset, I get a format is failed error message.
Last ditch effort
Can I use WST to make a backup RUU from the working phone and flash that to the dead one? All other attempts have failed to restore this phone.
I dont think so
Men you are already doing everything!!!
Does you have mtty... try this please it may works for you let us know what happend please...
http://forum.xda-developers.com/showthread.php?t=420785 the man in this thread stucks on splash screen so read just the mtty steps.
BTW does you unlock your wife's phone... is yours unlocked too? before do it...please respond.
The hope dies at the end!!!!! we have so much to´pics about this issue... why you are runing windows 2000? nad make upgrades? or does I missunderstood? extremely recomended Win XP.
I have Vista at home, and I read where many people here say that you can't do reflashes with Vista, so I use my computer at work, which runs Win2K. I haven't unlocked the second phone, but I thought that I did the first one. That was why I went to flash it. I wonder if the unlock didn't take and that put me in this predicament.
I understand now
Maybe a mistake using windows milenium or 2000 or whatever...
So if it say format failed i cant imagine other thing that do the thing i post you... so if you got questions about clear DOC Chip ask everything...
when you already get everything in a XP machine tell us please oh just for a recomendation unplug the minisd and during the process the mtty working on some lines dont launch programs check your USB cable maybe with a little scratch and moving makes a false contact at all.
Hey there, just want to say before I tell you my problems that this forum is cool. I recieved a lot of useful information and tools for my phone here. Thanks.
Onto the problems!
Okay so first of all, I was given an HTC Vogue on the Telus network from a buddy because my previous phone fell in the pool. I was having a blast with this phone, 'twas the best thing that ever happend to me.
Now before I get into specifics, I'd like to mention that I've never been able to connect to activesynce because the computer would not recognize the USB cable. I've never been able to fix that problem.
Recently I've been having problems with my phone. Sometimes it would take a little spill onto the floor from my lap because I'd forget it's there or whatever. The back casing would come off and the battery would come out. No worries, I would just pop it back in and off I go. But this time it would boot up to the Telus screen with the buncha red writing.
Code:
M 03
B 01
P DCAAXOM-4350H
R 3.41.00
D 3.07
After that text disappears, the phone would freeze at the Telus screen and either: a) No LEDs would flash b) a yellow LED would come on c) THe phone would be left on that screen and just shut off after a while.
So i did some research and found that I could preform a hard reset. Voila! It worked like a charm and I was off using my phone again, but it had barely been 24 hours before the phone froze and I had to reset. And the phone would revertback to the previous problem. Hard reset would NOT work. It would reset the phone but still freeze. Sometimes it wouldn't even stay on the hard reset, the phone would shut off as soon as I release the SEND button after holding all fo the hard reset buttons. So i went back here and on Google to look for the fix.
I've done a bit of research on possible fixes to my phone like disassembley of the phone and the placement of plastic sheet over a processor of some sort and flashing the ROM.
So what I did was look up some custom roms and what not. From what I understand you need a CID Unlocker before custom roms can be used. I looked around and found that I need the USB connector to work for the phone to become unlocked. But this conflicts with my current situation and whenever I try to flash with a custom rom from the microSD, it takes me to the Loading... screen and stays there without any mention of flashing a ROM. This is also the case when I try to put the CID Unlocking .nbh on my microSD card.
So I ask what I can do for my phone to revive it. I've done extensive searches on any fix to my phone with little or no result. I need some fixes fast because I have a tonne of important calls coming in that I need to answer. I will not accept that my phone is dead.
Please guide me in the direction on how to unlock the CID with a microSD card. Or just anything that'll enable me to use my phone again. I con't afford ot buy another one.
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11[/QUOTE]
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.
Also here is a link for the unlocker for the CDMA Touch on PPC Geeks
http://forum.ppcgeeks.com/showthread.php?t=20370
whitey10tc said:
BTW
The info on my boot loader screen reads.
VOGU100
SPL-2.01.0000
CPLD-11
Click to expand...
Click to collapse
I gather that you can get to the boot loader screen by the above info. While on that screen try pluging you cable into a direct USB port on the computer and then into the phone. If your phone is recognized it will change from serial to USB at the bottom of the multi color screen. If that doesn't work let me know.[/QUOTE]
I've tried that. The phone reads USB but the computer can't recognize the phone. Activesync won't work either.
EDIT
I've tried flashing with a stock rom. Everything runs fine in that screen. I soft resetted the phone and it went to the windows mobile 6.1 screen with an orange LED and just sat there, I wanted to wait but impatience got the best of me and I soft resetted and now it gets stuck on the telus screen again. Sometimes the green LED flashes as if the phone was running normally and the screen dims. I don't know whats going on.
I think I've tried that ppcgeeks thing but I can't be sure. It doesn't work because I can't connect my hpone with the USB cable.
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
patience
patience is the key.
patience is the key.
If you go to bootload screen connect cable and it changes to USB you should be connected.
Also here is a link to a tutorial
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
To be sure that your computer is not connecting to the phone plug usb in go to deivce manager and double check the USB if it is not connected correctly it will have a warning sign by that port. Try reinstalling updating your drivers for the usb.
patience is the key.
patience is the key.
beanage said:
My boot loader screen has changed after flashing the stock rom. It now reads:
Code:
VOGU100
SPL-2.01.0000
CPLD-3
same problem after flashing, just different writing on the boot loader screen.
Click to expand...
Click to collapse
You need to flash the SPL 2.31 bootloader
It appears as if it's fixed for the most part. Some minor problems but that doesn't stop the fucntionality of the phone. But I'm still pretty pissed that no matter what i do, my phone will not be recognized by the computer with the USB cable. i've tried everything and looked everywhere. Does someone want to send me the usb drivers for the Vogue? Please don't tell me that i don't need drivers because activesync won't connect. I've seriously looked all ove rthe internet for fixes and none of them work. Any pointers ro anyone want to send me official HTC drivers? I want to start using cooked ROMS.
here you go HTC windows driver will work for the vogoue
http://www.4shared.com/file/94429326/ffb09a5f/WindowsHTCdrivers.html
But unfortunately won't solve active sync problem. I would uninstall activesync and reinstall on your windows XP computer.
Quote from HTC website
Q.
Activesync is not recognizing my device, what should I do?
Be sure that you have not connected your device to your PC before you installed Activesync. If you did plug in your device before installing, uninstall Activesync and start the process over ensuring that you do not plug your device in until after Activesync has been installed.
Verify that your device is recognized by your PC in the Device Manager; if it is not, resolve that issue first.
Unplug your device from the PC for a few seconds and then plug it back in.
Perform a Soft reset on the device while it is plugged into the PC.
On the device, go to Start>Settings>Connections>USB to PC and check the "Enable advanced network functionality.
crap, my phone just ****ed off again. Same deal as before. Hate being broke.
help with vogue frozen loading screen
i unlocked my vogue and flashed NFSFAN 6.5 ROM and now phone freezes at loading screen and will go no further. i can still pull up bootloader thats all. any help or tips would be appreciated. thank you
what is your bootloader version
htc boot up screen and bootloader
m03
b01
acaaam-4070
r 2.26.00
s 3nfs
vogu100
spl-0.41.coke
cpld-3
are you using a GPS ROM if so you have the wrong bootloader and need the 2.31 from this post http://forum.ppcgeeks.com/showthread.php?t=20370.. Install the 2.31 and give it a try.
tried using 2.31 unlocker, when i run the RUU and says it will take 10 min it accually takes 10 sec and installs fast then after my phone restarts bootloader still says .41
You need that SPL 2.31 for that ROM
http://forum.xda-developers.com/showthread.php?p=3680838#post3680838
This is a quote from the facts thread for your ROM
First go here http://forum.ppcgeeks.com/showthread.php?t=20370 and
READ the hell outta it until you have it step by step.
(BTW use the 2.31 unlocker regardless about the GPS thing)
OK, now that you've read that (happy dance time)
Download the 2.31 Unlocker and NFSFANs WinMO 6.5 ROM.
Here is a good link for the boot loader. unlocker.
ftp://up.ppcgeeks.com/Vogue/Users/ImCoKeMaN/Vogue_unlocker_MFG_2.31.exe
yeah still can't get 2.31 to load on my phone. i tried to flash the stock alltell and sprint roms but at 29% it freezes or has recovery issues and will not go past 29%. flashed dcd 0.2.0 and got it to load! bootloader still shows .41 but now when i boot up phone it says in red at bottom of HCT boot screen.
m 03
b01
No radio
d1.17
Who is the original carrier You will need to get that OEM ROM and flash it. Then run the 2.31 unlocker follow the directions you can use the bootloader on the factory rom I have done it with sprint and alltel Vogues. The OEM ROM will reinstall your radio then you canuse the unlocker. The .41 unlocker is for non GPS radio and ROM combinations.
Hello mates,
My i-mate Jasjar doesn't start any longer. Here's how I got here. I tried to flash my jasjar with Crossbow ROM using ROMUpgradeUt.exe but it didn't do anything. So I went into the Country_ID_Error folder on the computer and executed MaUpgradeUt_noID.exe. My jasjar froze after this and everytime I restarted it just hung on the bootscreen that says i-mate.
So I tried using mamaich method using mtty and now I can't even get to the i-mate bootscreen. So nothing just happens when I try to power up the phone (I'm sure the battery isn't dead).
All I can do is just enter the bootloader mode. That is the only thing that I can do that I know.
Please suggest something. I'm lifeless without the i-mate.
Thanks and regards,
Aditya More.
i had this same issue, i task28?'d my device, whatever command that resets the flash structure, then booted into bootloader, and flashed this file:
http://rs507.rapidshare.com/files/184081773/JASJAR_WWE_11353_137_10301.zip
that should fix you up real good, hopefully.
Well thanks a lot. But it doesn't help. It gives me a connection error when everything is fine. USB is connected, ActiveSync USB connection is disallowed.
I forgot to mention, that when I task 28'd my device, nothing showed on the device. It just showed USB at the top and v2.01 at the bottom for ever, which means the task 28 wasn't probably successful or I ain't sure what.
Yeah, I had to ask you how if the above given file will work if the phone is in bootloader mode.
To fill you on more details, my phone somehow strangely starts. I'll explain how.
When the phone is switched off, and when I press the reset button, nothing actually happens, no activities can be observed.
When the phone is switched off and I connect it to the computer via USB, it shows the charging light. Now when I press the reset button with the phone connected to the USB, the charging light goes off and the USB detection sound sounds on the computer and the computer shows "USB Device not recognized". This means the phone started.
But strangely in both the above cases, none of the two lights on the phone indicate anything and display of the phone shows absolutely nothing.
The only thing I can do with the phone now is enter bootloader.
Also, since I compromised so much, is it possible that I can still flash it with WM6? Because going back to WM5 will make me feel miserable.
Thanks.
@cheapusenet:
I tried flashing with that file. It flashed successfully, but the screen is all smudged. I soft reseted the phone too (using reset+two soft keys) but it keeps displaying that same smudged screen.
Good news is it did something.
Bad new is that it didn't make the mate work.
Please help. I'm dying without the phone.
Thanks and best regards,
Aditya More.
is it possible you can get a picture of what screen its showing? I THINK it happened on mine as well, did you let it sit for 10 or so minutes? if i recall the bootscreen was all corrupted but it started into WM5 just fine.
and regarding wm6, i'd attempt to get the device working before you try and get fancy. is the device cid unlocked? mine was and thats what was causing the issues.
Originally Posted by mamaich
if you can enter bootloader - use "task 28 55aa", this would restore DOC to its original layout.
If you cannot - contact service center.
if you didnt run that exact command, it's probably a good idea.
and you could try reflashing that stock imate rom?
This is all that happens.. I have waited for 5 minutes. I'll wait for 20 minutes now.
i waited for 30 minutes.. no go..
yap it did that EXACT same thing to mine.
reflash it, i think that fixed mine.
if that doesnt work, attempt flashing some custom roms.
is it CID unlocked?
i flashed it twice.. no go..
what's CID unlocked?
CID
Read the Wiki on my sig link
cid unlock allows flashing of roms that don't match your device branding.
i don't remember what brought me back from that, i may have flashed a custom rom with the imate cid settings in it? i don't remember.
i'll post a rom that i think may have helped in a few hours, I have slow upload speed. until then, just keep tinkering.
also, you should only be flashing nk.nbf. not the ms, or radio nbfs.
http://milfweed.info/UNI_AKU3_2_WWE_IVAN_beta_4_extrom_public.rar
try that rom.
hey man.. Flashed the rom with Ranju's ROM of WM6.1.. it worked.. But I can get the phone to be turned on. i mean device turns on but I can't make or receive calls or text. Let me check the thread of that rom. Thanks a ton for your support. Really appreciate it.