Hello there magicians.
My poor Artemis is in trouble.
After an upgrade to a new rom (Artemis touch 4.02) and when everything went perfecty well, I tried to put greek in it. After reseting the device starts but stucks in the screen before opening WM 6.1
HELP!!!
How to enter it in bootloader?
shut down ur phone by removing the battery then again put in the battery then press the record button and the power button together u will see the red blue screen this is boot loader mode flash it with official factory rom this is important and dont forget to remove ur sim and memory card before flashing
Thanxxxxxxxxxx
A lot
And now what I ll do about greek keyboard?
Related
I flashed an Elf yesterday with an original HTC Rom (german). In the beginning all worked fine, after flashing and restart it showed the HTC screen, all in german, and said: no Sim. ihad removed the Sim and SD Card before flashing. So I switched off the device, put back Sim and wanted to start. right now the device doesn`t boot any more. It just shows a T-Mobile Screen for about 10 sec and than goes off. I Tried the recover Rom from sniper911 (HTC Test ROM), but the device doesn`t start in bootloader Modus. I can`t access the bootloader modus. What to do????
charge your battery and try hard reset
dear all experts ...
I tried to update my Shadow by the new wm6.1 rom.. the first time it went to 100% and restart with an error 270 : the image is corrupt . After, when I boot loader, it go to 2% and restart every time ( many) :
I'm stucked at bootloader mode and tried many roms but no one sucsess ... all of them reach 2% and then stopped.
even I tried the original one (Shadow_Software_Update_1.11.531.5.exe) from t-mobile official site but also same result.
so can any one help me and give me any solution to try?
try to install this on your phone
http://forum.xda-developers.com/showthread.php?t=394478
after that try installing a cooked ROM
Dear sir;
thanks a lot for attention to my problem and ur kind reply.
I already tried to do this but...
* How can I upload sspl/uspl to my phone from bootloader because it's the only mode I can work my phone?
* when I tried to do USPL + RUU it go to 100% and then the phone restart and the RUU program says corrupted image...
then the phone stays in it's state (only can go to bootloader mode).
can I use MTTY program to flash sspl/uspl and USPL and then the new rom? if yes .. how I can do it?
Or what may I do my friend..
thnx a lot again
if you can only get to the bootloader then try flashing to the t mobile rom, then start over
Mee toooooo
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
isfected said:
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
Click to expand...
Click to collapse
Power off the phone
Press and hold the camera and voice keys
Insert the USB cable, Keep holding the camera and voice keys until you get the bootloader screen
Then flash an original ROM.
Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!
rupesh baviskar said:
Hi
Plssssss Help me. i'm using HTC touch 3450 and i have upgraded my device with wm6.1
NOW THE PROBLEM IS...
1. MY DEVICE BUTTONS(HARD KEYS) NOT WORKING BUT I CAN MAKE THE DEVICE IN BOOTLOADER (TRICOLOR) MODE BY PRESSING CAMERA + POWER BUTTON.
2. AFTER INSTALLING A ROM WHENEVER MY DEVICE STARTS IT SHOWS THE HARD RESET SCREEN (BLACK SCREEN........... ALL THE DATA ...BLAH BLAB......)
I HAVE TO REMOVE THE BATTERY AND START THE DEVICE AFTER 30 MINS.) PLEASE NEED THE SOLUTION ......
3. I AM TRAYING THIS FOR A MONTH BUT NOTHING HAPPENS
PLZ GUYS HELP MEEEEEEEEEEEE OTHERWISE I'LL BE CRAZY!!!!!
Click to expand...
Click to collapse
hi
if u can get ur tricolor screen then try this
connect the usb cable to pc and see if u get the USB words on the phone tricolor screen if so good try flashing any official ROM the same happened to my phone long back did the above got my phone back asuming u have done HSPL for ur phone if u have not done that then the only way is to take it to service
hope it helps good luck
thanks
hari
Wrong forum.. Touch P3450 is not a touch 3g , its the original touch (ELF version)
but i will try and help as i have owned both.
if your hardware buttons are not working it could be possible that your send and end keys are stuck down as this key combo brings up the hard reset you are talking about.
think you are going to have to open it as it sounds like a hardware fault, and if you cannot get into bootloader you cannot flash
if it was working alright before this is not the case, but either way you will have to fix your camera button and get into bootloader
Hi everyone in a panic but am trying to stay calm lol...
So i think i have over tinkered and broken my phone....
I am able to get to the boot loader by powering on and holding down the volume button and it will allow me to flash radio and rom to it but it never boots after just hangs and says loading please wait..
I have tried roms
chuckyrom 23148 tabtasitc
OzDroid 2.00
and radio's
2-11-50-26
2-11-50-26
and the same thing with these in any combo
I have ran task 29.. and have to admit i am left a bit worried now... any advice would be great i am going to read the rom section and try and get a new rom and radio combo...
Any Ideas ...
Okay phone seems to be flashing... but task 29 is not seeming to wipe my phone correctly it is still left with the chucky room splash screen after a task 29 i thought this should go white
First thing, your phone is fine - since you can get into bootloader mode.
What version of the HD2 do you have - is it the T-Mobile USA version?
Have you installed HSPL on your phone?
Go to the HTC website for your location and download the ROM for your phone (if your phone is unbranded then download the HTC ROM or if it is branded then download the mobile operator's branded version of the ROM). NOTE: If you are using a TMOUS phone, then double make sure that you are downloading the USA version of the T-Mobile ROM.
Bootup your phone into Bootloader Mode, then connect to your computer via the USB cable. Run the downloaded ROM. Ignore the connected via activesync in the warnings.
Hi i have a O2 uk hd 2 i thought the phone was okay as the laod was coming up and it seems to be writing to it... hm strange it just says loading but the red writing does not appear on the bottom left to say rom and radio version...
Hi have downloaded and flashed the o2 rom from the HTC website it seems to have gone okay BUT now when it boots it is just stuck on the O2 splash screen and goes no further..
I have now removed this from usb and re inserted the sim card and am getting this at the bottom
R 2.07.51.22...2 (Is this the radio?? or the Rom)
g15.32.50.07u
d 1.72.82124
and it has come up slowly and seemed to be loading windows mobile.. and then crashes and starts all over again...
Okay so I have now got a stock o2 rom from htc on my phone. and it is working.
Thank you Fred_up for the advice... should i now be able to start again trying to load a custom rom back on to the device to enable me to use android again?
Try doing a hard reset. While phone is Off, hold Volume up & Volume down buttons, then tap the Power button.
In Bootloader Mode, what does it say?
pull off battery and wait 5 minutes. let the phone cool and the insert back the battery.
it should be alright. however everytime your phone overheating its freeze again..
any solution to that let me know.
cool off your phone. take out the baterry and then once the phone is cool insert the battery and it will boot again.
now hd2 have this problem. overheating. the phone will freeze. hd2 now need freezer to make it not freeze.
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
after you have fully charged your phone, try flashing it again...Happy New Year.
tnx.... but how cant flash it again... becuze its doesnt start to bootloader... i cant it power on.. plz help me... hw do i flash it????
you try to flash WM5 rom and then flash the rom. offline flash memory card.
dulands said:
i have hp ipaq6828 phone... so i did flash it with new rom after complete full install my device came to black screen.. i was try to get turn on it again.. but it cant... its nw charging.. charge light is work fine... but no more power on or no more boot loader screen & hp logo screen... so how can i ge bootloader sccreen again??? or hw can i fix my devicce... please help... i love my phone & i dont have enought my to buy new one....
Click to expand...
Click to collapse
try to Hard Reset your device , here the way to do that...
Perform a hard reset with the iPAQ. To perform a hard reset,
1. Press and hold the Answer/Send, Power, and End Call buttons.
2. While holding these buttons, use the stylus to lightly press the Reset button on the bottom (located at lower left base of the iPAQ), of the HP iPAQ until the device restarts.
3. When the HP iPAQ restarts, release all of the buttons, and then remove the stylus from the Reset button. The HP iPAQ restarts and powers on.
CAUTION: A Hard reset clears memory, deletes all data (such as owner information under Setup Wizard and AutoConfigurator) and restores the rw6818/rw6828 to its default factory settings. The action will erase all data that you have created and programs you have installed, but will keep all the preinstalled programs that were in the phone when your phone was first delivered to you. Be sure you have backed up all your data in a mini SD card or on your PC before performing a hard reset